My CPU is too noisy

Similar Questions

• Satellite A500-040 - too noisy CPU fan

  My CPU fan runs too fast and too loud. The fan speed is still 73 percent. Although I have not used all the programs, the CPU fan speed is always 73%. Never speed is made once it has reached 73%. Even the CPU temperature is about 35%.
  I tried to do as a result of the actions:
  It solves not 1 updating bios/drivers-
  2 changing settings of the power plan does not solve
  3 cleaning cooling module does not solve

  Can someone help me?

  Unfortunately there is not much you can do about it. Cooling fan is controlled automatically. I put t know which options have the power that you have changed, but please try to change the option for cooling method. You can find it in the advanced power options > Toshiba power Saver saver > cooling method.
  Use the optimized battery option. This should reduce the activity of fan cooling.

• iMac restarts after 5 minutes of the heavy load of CPU/GPU and noisy fan

  Hello

  My iMac (late 2012 if I remember) restarts when under heavy load for a while.

  I work a lot with Final Cut Pro X.

  Whenever I have add clips in an event, Final Cut allows you to copy and then transcode and analyze the clips, and this task's CPU/GPU intensive (Final Cut Pro X uses OpenCL, where CPU/GPU). After a few seconds, the iMac fan begins to be really strong and seems to reach its maximum speed.

  Then, after a few minutes of this heavy burden, the iMac simply restarts, and the fan slows down and stop. After the reboot, everything is back to normal, with the exception of the warning illustrated by Mac OS X, who said that the closure was not planned.

  I'm sure that this behavior is not normal. I don't see why a computer should reboot/crash when under heavy load.

  Note: you can also, to transcode some clips or movies I used the excellent software called Handbrake, using CPU only encoder ffmpeg, and I don't remember having accidents even if the CPU has been loaded and FAN running loud too. So maybe it has something to do with GPU?

  How can I understand what is happening?

  Thank you very much.

  Thomas

  First try to reset the SMC reset management system (SCM) controller on your Mac - Apple Support

  If continuous reboot to run the Apple Hardware Test mode extended using Apple Hardware Test - Apple Support

• Tecra 8100 CPU gets too hot

  Well, some may remember my previous post about the fan activation in my Tecra 8100.

  This laptop came to me as a gift by a customer, because the screen didn't work. After some research, the problem was the internal cold cathode that was broken. Once replaced: Yes! a free book for me! It was a Pentium III 650 Mobile, with 64 MB of RAM and a 12 GB hard drive. I replaced all the components (which are now on sale, btw), and now has a Pentium III 850 Mobile, 512 MB of RAM and a 40 GB hard drive. Someone gave me a card PCMCIA of WiFi 11 Mbit/s, and now how it works with Windows XP Professional and updated Toshiba Utilities and drivers downloaded from Toshiba USA.

  What's the buzz? SpeedFan, Motherboard Monitor and other monitoring utilities reported temperatures up 72a? Aºc in the processor. I opened the computer laptop and put thermal paste instead of the sticker that has the heat sink. Temperature guard high and utilities Toshiba even with parameters ' cooling high performance "does not have the fan to cool the cpu...

  I hangs at all, but the business cards and pcmcia laptop have too hot even with the system works with any of the applications running. Lowering of the CPU clock or the ratio helps not at all.

  I think putting a fan somewhere extra to force air circulation and that cool the cpu, unless...

  ... Toshiba could develop a utility that allows you to directly control the fan speed. I don't know if the thermal management is hardware or software-driven. If it is a software-driven, it should be easy to create a utility that directly access the fan and temperature records. It would be MUCH better than simply let the computer decide when and how long to activate the fan.

  I'm sure that Toshiba engineers are busy with more important things which will not create the utility for us, so...

  .. What to check or do to cool the CPU at more appropriate values?

  Thank you all!

  Hello

  As in you previous announcement describes the Toshiba power saver controls the CPU and fan usage.
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=12585
  This software works very well, and if you use the laptop as prescribed, you should not get all the problems and overheating problems.

  The problem is that you have changed all the devices and parts on you laptop. The new parts are effective, but produce more heat.
  On the laptop you can cool the CPU with a small fan, and if she goes out, it is necessary to decrease the performance of the processor.
  It is a simple fact. All these functions can be set with energy saver.
  In addition, it is very important that your cooling module is clear and free from dust and debris obstruct the work of fan.

  PS: Useful link about changing CPU:
  http://support.toshiba-tro.de/KB0/FAQ5300W5000XR01.htm

• Satellite L40 CPU is too hot?

  I just bought a Satellite L40 with a intel T2370 processor and I have a feeling that its temperature is high enough.
  Everest ultimate sensors show a temperature around 70 c during operation.

  This temperature is normal?
  Other users have a similar temperature?

  Thank you.

  Hello

  The temperature of your laptops is certainly not too high!

  You need to know some important facts;
  First a few 3rd party tools don t always provide values for temperature of 100%!
  Second, the internal temperature is constantly changing.

  Running some games, videos, or other high performance programs would lead to higher heat dissipation and a higher temperature
  This is a common behavior of laptop so don t be worried that something is wrong with your laptop ;)

  By the way; the laptop supports an overheating protection. It will stop automatically if the temperature is too high.
  If the computer laptop doesn t turns off automatically, your CPU temp is ok.

  Good bye

• Dell Studio XPS too noisy!

  I have a Dell Studio XPS 9000 with a Radeon 5870 graphics card that makes too much noise. I think it is the fan noise. I called technical support, which replaced two fans. Did not help - if anything, it is now more noisy he was! All idling, it is not quiet.

  The system is about a year. (Is there more than the 2 fans in the system by the way?)

  (1) can anyone suggest how this system down?

  (2) I contacted a vendor third 3d that makes fans more silent, so-called, but the seller must exact model or type numbers or something Dell fans. Does anyone know how to find out exactly what kind of fans are in the Dell XPS and also exactly what solutions third-party 3d for quieter fans there are, if any?

  It is also an old thread, you should start a new one.

  I assume you mean a Studio XPS 9000.

  This model according to the configuration guide, has no onboard video and no on-board video port is shown in the figure on page 20 of this installation guide. If you cannot select video...

  What do you mean by "the noise of the fan? It's just the fan spins at high speed or is it squealing or some other noise?

  You can open the case and make sure the fan and vents are clean. Use canned air to blow 5 - year-old dust of all components.

  And if this started after a recent update of MS, you can consult the Web of AMD site for an updated driver for the video card today, that works with any version of Windows that you are using before you spend money unnecessarily.

• Edge 320 CPU overheats too easily.

  Hi, when I don't do anything too intensive on my Thinkpad E320, the temperature of the CPU is about 50 degrees Celsius, but when I play a game, even a game that is of the requirements is much lower than I need, the temperature goes down to 85 degrees and the strength of the laptop restarts. What is a safe temperature of CPU to do, and how can I keep it cool? I tried lifting up so that there is space between the vents on the bottom and the table, but it makes no difference.

  Thank you!

  Overheating problems are often caused by poor air circulation in the computer case. Have you tried to use a Chill Mat?

  Also, try cleaning with compressed air, make sure all the fans are nice and clean and the heat sink is shiny. Spray just the air across it, it's going to be enough to remove the dirt and grime.

  Since the Manual of Maintenance of equipment , it seems that you should only take the backdoor to clean the system. The instructions to remove the backdoor begin on page 49, that will not void your warranty; If you decide to do something else, you may void the warranty.

• Low utilization of the CPU, system hot, noisy fans

  My 2011 27 iMac mid has worked well. Here are the basics.

  

  The system has an SSD instead of a hard drive (therefore less heat than normal). I use the development system: it is not and has never had a lot of junk on it. About four weeks ago, the system started to run hot and the fan was strong while the CPU is about 99% vacuum. I have download the trial of TG Pro and the CPU seems

  

  "Load" in the photo below, which is less than 3%, is high normal baseline because I'm running TG Pro and activity monitor.

  

  The noise is very annoying and seems out of line for the load of the system.

  Someone has any practical suggestions or see obvious problems? (Until you point out 24 GB RAM and other fundamental issues, keep in mind that this system has been stable and performing normally in the current configuration for about nine months, save El Capitan updates).

  Resetting the SMC often with these problems reset management system (SCM) controller on your Mac - Apple Support

• Advantage 2545: Too noisy printer

  Is anyone experiencing the same thing with all-in-one printer, HP Deskjet Ink Advantage 2545. The printer works fine, but it has an annoying problem. It is curious when you're printing. It's really disturbing. Is it possible to make it less noisy?

  I am a writer and blogger at booboone.com . I like and use of HP products in my office.

  Hi @Delarno

  Welcome to the Forums of HP's Support. I understand that your 2545 seems to be stronger, then it should be.

  Spec wise, it is not that strong. Although all the ears and reviews of the sound intensity is different.

  (Viewer position) of acoustic pressure: LpAm 50 (dBA) (mono project printing)
  Sound power: 6.3 b (a)

  Source: Plug printer for HP Deskjet 2540, 2545 printers

  I do not have the printer, but if it is strong, it would be interesting to talk to a hotline. This link will create a case. www.HP.com/contacthp/

  It also brings a squeak?

  Is this a new issue or the printer since always noisy?

  So new, this is an event where he started to be noisy?

  Look for any obstruction or broken in the transport path part.

  Make sure that the carriage moves freely.

  Remove and reinsert the cartridges to ensure that they are properly installed in the device.

  Perform a hard reset. (while the printer is on, unplug the power cord for 30 seconds and then reconnect the power supply)

• ENVY 17 3D - no overheating, no surprise, but suddenly the CPU is too

  Since HP has really managed to kill the line of envy and merge it with the Pavilion dv line, brand envy low poor quality material pavilions, I still use my old, real envy 17 3d 1195ea apart elitebook workstations brilliant, because his only able successor, the 17 line 3200, is no longer available for purchase , and something more recent (envy j# line) is low-middle-end consumer crap.

  now the line want 1000 overheats as soon as it is powered on without news, I could manage quite well by opening to the top of each month and cleaning inside, same repasted CPU & GPU some 3 months ago, making the time decreased by 10 degrees in general.

  However, since a few weeks I meet some really strange and excessive overheating of the CPU (although the 5850 m GPU was overheating mainly of firs to date).

  It is idling at 65-85, but with each burst (happening several times a second), it reached 99 to 100 degrees for a fraction of a second. That is to say. times are constantly jumping up to 100.

  pull up something really stressing, as a game (CS - because its bound processor) or an application with emphasis on the CPU, makes the scope of the CPU 100 degrees in less than 1-2 minutes, leading to the heavy restrictions and ergo great performances.

  even strongly linked to the GPU games keep the GPU at 90-95 degrees (from my experience in the past, during bad weather the GPU begins to 104 degrees, so no question of limitation at all), while the CPU gets up to 100 and the throttles.

  now my question - is the only explanation for what the thermal paste has become dysfunctional? That is to say. repasting it would solve it?

  or else maybe the reason for this?

  Thank you

  OK, repasting has a job well done. now, I'm back at temperatures around 85-98 for two, CPU GPU & under medium to heavy load. Surf and light load remains at 70-80 degrees.

  so I can't tag this thread as resolved, even if only a 'real' solution would be a different cooling system, IE. a second fan heatsinks more/more thick, Gill more...

  or a REAL new Envy 17 3D, IE. no desire to brand pavillion.

• Too noisy fan on Processor__ noise

  I have a loud fan in my processor which is constantly changing and all using the computer.  What could be the problem?  Should I be worried?

  Thanks a lot for your comments.  I'll certainly check things.  Much appreciated!

• Portege R700 - high CPU fan noise

  Hello

  I own the Canadian version of the Portege R700, called Tecra R700 (PT319C-00E002).
  The CPU fan always runs between 43 percent and 51 percent (regardless of the mode of selected frequency), which makes the noisy computer - too noisy to be used comfortably, too noisy to be used at meetings of air-conditioned silent.

  The fan seems to be controlled by the BIOS, as well as applications such as SpeedFan are unnecessary. Is there a way to fix this?

  Kind regards.

  Hi dernierrecours,

  > CPU fan always running between 43 percent and 51 percent (regardless of the selected frequency mode)
  This means that the fan runs always at the same level regardless cooling method that you can choose in Windows power management?

  Well, have you tried updating the BIOS? The latest version is installed?
  Check out the Toshiba page for an update.

• Fan brand new Pavilion HPE h8-1120une System (case) is much too loud

  Hi all

  Just received delivery of the new Pavilion HPE PC.  Turned on the PC and the fan is way too noisy.  Applied just latest Bios Rev 7.12 and took a look in the Bios and can see the system fan speed is constantly running a little over 4000 rpm and the CPU turns fan I think a little over 2000 rpm, there are no adjustable parameters for the thermal options.

  The system fan is the noise, the power supply fan is not yet noticeable.

  Any ideas how to solve this problem would be much appretiated.  I'll try to call HP support tomorrow and see what they can do...

  Model No.: h8-1120une
  Product #: QU296AA #ABG
  Serial No.:
  Software update #: 11AP3MRW604 #SABG #DABG
  Service ID #: 060-212
  PCBRAND: HP

  Laptop HP ENVY 17-j005tx, HP ENVY 27 - k001a, HP ProLiant MicroServer Gen8 G2020T, HP MediaSmart EX495 Server tilt, HP MediaVault 2020, HP ENVY 120 AiO Printer

  This problem has been solved, solved by simply moving the PC in den where I wanted to put in place, and then he moved to my study! I have absolutely no idea why this has solved the problem. My guess is maybe the power cord or the video cable * HDMI) were not properly connected or the plug in the living room playing place... in the cher, is now resolved.

• Tecra S11 - CPU fan is high speed

  Hello

  We have a problem with nine Tecra S11 / Windows 7 64-bit. The CPU fan is noisy high speed during ignition and start Windows. No change after logon. Speed remains unchanged up to go to the sleep mode once. After waking up, everything is OK.

  For me, it seems to be a problem with the firmware (BIOS). Update V1.70 but no change. We have same problem with the S11.

  Any ideas?

  Cordially Stevep

  Hi Stevep_1,

  Have you tested different cooling options in Windows power management? Check it for each profile, and then select battery optimized cooling.

  It work?

• My HP Pavilion a6000n cpu upgrade

  I got this hp Pavilion a6000n friend and I basically rebuilt this computer, but I'm not sure what CPU I can go to. I've been watching this cpu for my computer. I am running windows 7 64 bit. This upgrade of the processor is possible for my computer?

  Edit: I also watched this cpu, if the other cpu is too powerful.

  Here are the specifications of your HP Pavilion a6000n desktop computer and its card mother M2N68 - LA (narrated). Based on these specifications, this model supports the following processors;

  Type of socket: AM2
  TDP: 89 watt
  Athlon 64 X 2 with Dual Core technology up to 5600 + (up to 89 watt)
  Athlon 64 4000 + less than
  Sempron less than 4000 +.

  Neither the processors you listed works on this computer.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation