My drive external hitachi hard works like

Similar Questions

• How to save raw files on an external drive but the hard work during the development?

  I want to save my raw external hard disk files, but when I work on copy them some files on the hard disk of the computer is faster and when I finished to remove hard drive but continues work to develop, so next time I'll get the file from the external drive it will show develop it I created. How can I do this?

  Thank you

  ts3287 wrote:

  I want to save my raw external hard disk files, but when I work on copy them some files on the hard disk of the computer is faster and when I finished to remove hard drive but continues work to develop, so next time I'll get the file from the external drive it will show develop it I created. How can I do this?

  Thank you

  In fact, I don't think that smart insights do what you ask, although they could be a solution to a different problem. Smart insights are especially useful when the external drive is not connected (that has not been mentioned in the problem statement).

  In general, the workflow of moving pictures on an internal drive, changing them, and then remove the pictures back to the internal drive is unnecessary extra work that adds almost no advantage. There is such a difference in small speed based on the speed of drive when you load a photo into the development module that you may not notice, and it can be eclipsed by the time it takes to move the photo. Ian Lyons did a study and in most cases, the difference between editing photos on a hard drive internal and editing photos on an external drive was small fractions of a second.

  So my advice to you is just to let the pictures on the external hard drive, no moving pictures from here to there, not too much space on your internal drive with smart insights.

• Satellite L500-1WP: after Win8.1 upgrade USB 3.0 drive external does not work

  Satellite L500-1WP

  After updating Windows 8 to 8.1 my drive USB 3.0 external do not work.
  Windows message: "device not recognized".

  Hello

  I guess you are talking about an external HDD that supports USB 3.0 standard.
  Right?

  Have you tried to connect to another USB port external HARD drive?
  The USB ports work correctly in relation to other USB devices?

  The USB 3.0 device supports Win 8.1?

  You should check this.

• Inspiron 530: drive external sata hard not automatically recognized.

  Hello
  I have an external sata Hitachi HD.
  It comes with a back plate for external sata connector.
  When I plug this HD anything happen on windows (Vista SP1), I need to go into the Device Manager and search for new devices.
  The HD appears, then it is mounted.
  But it should not work this way.

  On my old computer (Asus motherboard and windows XP SP2) this HD works just like any USB device:
  When I plug in the external Sata connector, it mounts instantly and removable devices icon will appear in the bottom right of windows.
  If I want to remove the HD I just need to click on this icon and select the HD.

  I would like to than this HD to work on my Dell, as it does on my old computer.
  Is it possible?

  Thank you for your help.

  
  

• I bought a whole new office 27 "Mac provided with Adobe CS6. Everything worked like a charm until the 1 TB hard drive, developed a bad sector and the Apple Store reinstalled a new I had extended warranty with them. The recycled player I

  I bought a whole new office 27 "Mac provided with Adobe CS6. Everything worked like a charm until the 1 TB hard drive, developed a bad sector and the Apple Store reinstalled a new I had extended warranty with them. They are recycled the disc immediately (like crazy, I don't ask for this return to get the data off it.) But fortunately, I have all my data on CrashPlan. I downloaded it and it was working fine except that I downloaded it on the desk and not the original location so he had succeed. I also have an external 1.5 TB drive that I wanted to make it bootable, so I installed Mavericks 10.9.3. Then I advanced and installed on disk newly installed too.

  I think that because I have a new reader that adobe thinks, I have a new computer. I bought the 27 "Mac new on Ebay and it came loaded with the software, including CS6. I have a serial number for CS6, but Adobe says that it was not valid. (I've owned CS2 and CS4 now CS6 that came preloaded on the Mac by the seller who told me that the software has been registered for the Mac?

  I'll re - download the backup to the original location but this time (I still don't think that it will work with Adobe.) What can I do about it?

  iMac 27 inches, end of 2012

  Processor 3.2 GHz Intel Core i5

  Memory 32 GB 1600 MHz DDR3

  Graphics  NVIDIA GeForce GTX 1024 MB 675MX

  Software  OS X 10.9.3 (13D 65) @.

  You must contact Adobe Support by chat or phone when you have the serial number and activation problems.

  Here is a link to a page with options to help make contact:

  http://www.Adobe.com/support/download-install/supportinfo/

• Drive external hard USB - cela used to work now I get an error message = "this device cannot start. (Code 10) "Any suggestions?

  Drive external hard USB - cela used to work now I get an error message = "this device cannot start. (Code 10) "Any suggestions?

  Hello

  I suggest to refer to this link and follow the steps in this link and check if that helps:

  http://support.Microsoft.com/kb/943104

  It will be useful.

• After Vista update cannot find the external hard drive, AutoPlay does not work, and new unusable disk appears under my computer

  After Vista update cannot find the external hard drive, AutoPlay does not work, and new unusable disk appears under my computer. Also I can't 'manage' my computer because I do not have "permissions". I tried a fix he 45071 and it did nothing.

  Applications, (Norton and McAfee) (including free evaluation versions are notorious for not not upgrade (or uninstalling) itself.) If NIS has been installed for 3 years, you have NIS update at least once and maybe twice (e.g., NIS 2009 > NIS 2010 > NIS 2011).

  [You may want to print these instructions for reference offline. If a step said to reboot, reboot.]

  1. download the Norton Removal Tool, save it to your desktop: ftp://ftp.symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  2. close all open applications (that is, anything with an icon on the taskbar).

  3. After completing some you have a copy of your handy product key, uninstall all Norton software (including LiveUpdate and everything Norton Add ons) viaControl Panel | Programs | Uninstall a program (or Control Panel |) Programs and features, if you are using the classic view).

  4 IMPORTANT! -Online activate Windows Firewall immediately after the restart.

  NB: Now you're "working without a net": no to ANYTHING else online (e.g., navigation, reading e-mail, chat) until you have completed step #7 below!

  5. right click on the file that you saved in step #1 above, and then select run as administrator.  DO TAP not your keyboard until the race ends, then restart.

  6. do a clean install of NIS 2011 (using your product ID, if need be) & reboot. CF. http://www.symantec.com/norton/support/kb/web_view.jsp?wv_type=public_web&docurl=20080514162318EN

  NOTE: Do NOT activate or install additional modules of Norton (for example, Norton Anti-Phishing) immediately.

  7. manually and repeatedly run LiveUpdate (Norton) until you get a prompt "no update more".

  8. open Internet Explorer (only) to http://support.microsoft.com/kb/923737 & run the difficulty.

  9. open Internet Explorer (only) to http://support.microsoft.com/kb/971058 & run that set it by DEFAULT and modes and AGGRESSIVE. [1]

  10. restart once again & test.

  NB: Installation KB971029 disables AutoRun/autoplay on USB connected but not 'brilliant media' external drives (i.e., CDs & DVDs). See http://blogs.technet.com/b/msrc/archive/2011/02/08/deeper-insight-into-the-security-advisory-967940-update.aspx

  ~~~~~~~~~~~~~~~~~~~~~~~~
  [1] full Disclosure: the difficulty operating in AGGRESSIVE mode will remove your update history but not list the updates installed in Add/Remove Programs (Windows XP) or installed updates.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• I SAVE ALL MY DATA TO AN EXTERNAL HARD DRIVE MDL WD16001032 AND LOOKS LIKE THIS INS DEVICE IS NOT COMPATIBLE WITH WINDOWS 7... WHAT CAN I DO?

  I SAVE ALL MY DATA TO AN EXTERNAL HARD DRIVE MDL WD16001032 AND LOOKS LIKE THIS INS DEVICE IS NOT COMPATIBLE WITH WINDOWS 7... WHAT CAN I DO?

  I SAVE ALL MY DATA TO AN EXTERNAL HARD DRIVE MDL WD16001032 AND LOOKS LIKE THIS INS DEVICE IS NOT COMPATIBLE WITH WINDOWS 7... WHAT CAN I DO?

  I don't understand. What makes you think the reader 'is not compatible' with Windows 7? Windows (or any other OS besides) sees no external hard drives as "compatible" or not...

  Now if you have a PROPRIETARY disk, then that is a different case. If you find my answer helpful, please click the button "Vote as helpful"! Thank you! My Blog

• External USB hard drives lose its connection and work stoppages. __

  External USB hard drives lose its connection and work stoppages.

  History

   
  Windows 7 Ultimate - 64-bit
  I installed it on a HP Pavilion, OS, 64-bit, and I have this problem.
  People report that it does not occur with Windows 7 32 bit OS.

  Problem:
  Any brand of external hard drive USB (and other USB devices sometimes) lose its connection and stops working only when copying large files internal drive to external USB drives.
  The USB device may appear to work properly when Windows first starts, but later stops working (crashes computer) after the start of large files to copy. You must restart Windows for the USB is working again.
  This only occurs when you copy files large files to THE USB port, not on the internal drive. It happened when I synicing my IPhone with Itunes when it started the synchronization of music files.

  According to the suggestions I have:
  1) updated the BIOS from the websites of the manufacturers.
  (2) power management disabled on the USB hub for disks
  (3) ensure that the BIOS for Legacy USB is set to.  I don't have this option in the BIOS settings.
  (4) this is not a motherboard problem, it is located on three different MB that we use.
  Also tried three different USB drives and different cables.

  Because I tested with two different computers updated and USB drives, our opinion is that this problem indicates that the Windows 7 64-bit operating system.

  Someone knows a solution?

  Hi Jh6284,

  Thank you for posting.
  What is a version of Windows 7 RC or RTM?

  You can try to uninstall and reinstall the drivers for the USB ports in Device Manager.

  UNINSTALL ALL USB ENTRIES IN DEVICE MANAGER ASSOCIATES.

  1. click on START
  2. right click "Computer" and select "Properties".
  3. on the left side, click on Device Manager.
  4. expand the 'USB Bus controllers' category
  5. right click and uninstall all THE references listed
  6. restart your computer and check if it works.
   
  I suggest you go to the Web site of the manufacturer of your and try to install the latest drivers for the chipset. Make sure that install you in compatibility mode there is no driver for Windows 7 64 bit.

  Please go through the article below to install in compatibility mode.
  http://social.technet.Microsoft.com/forums/en-us/w7itproappcompat/thread/cdd894f8-1ee2-43e5-952b-d04c25779a7f

  Kind regards
  Technical support of Microsoft-yama.

• MacBook pro work leave because of pulled and broken wire.  I took out the hard drive.  the hard drive has all my files that I wouldn't need to clear all of the other personal files?

  MacBook pro work leave because of pulled and broken wire.  I took out the hard drive.  the hard drive has all my files that I wouldn't need to clear all of the other personal files?

  It does not start to the top, screen and hardware ok except belt disconnected.

  also can I sell adapter, brand new, never used. where can I sell?

  Hi Wally, the hard disk OS X and all of your files. Get a case for your reader, and it backs up. Try OWC

  Always keep your Mac backed up on an external drive with Time Machine or utility of cloning like SuperDuperor double clone.

  Try eBay for the adapter.

• Drive external HARD Toshiba PX1267E - 1 32 cannot be properly detected/installed

  Hi everyone, I need help.

  I have a Toshiba PX1267E - 1 32 external hard drive that I used on my PC under Windows XP. Yesterday, I bought a new laptop with Windows 7. When I plug the HD via USB, it is said that it cannot be properly detected/installed.
  It does not appear in 'my computer' and I really need to transfer a lot of data on my new laptop.

  I can do to make it work?

  Are there drivers for Windows 7? I can't find my original CD

  Any help is very appreciated. Thank you

  Hello

  Looks like a HARD drive contains a preinstalled software that is not compatible with Win 7.
  I'm not sure if this will help but try this:

  Connect your HDD to the other no Win 7 PC
  Select the CD drive with your browser (password)
  Run the ONSPCLCK.exe (or another exe file which controls and password.)
  Select 'Options '.
  Select "Disable security password"
  Enter your current password
  Unplug the HARD drive
  Connect the HARD drive to laptop with Win 7 OS.

  welcome them

• WD My Passport not recognized as drive external HARD on windows 7

  Hello

  I would like to ask if anyone has experienced this and how the address the issue:

  I just bought a WD My Passport Ultra 1 TB and tested on two devices (desktop to Win7 ultimate) and portable Win7 Pro. At first I used it on my desk and it it detected as required WDC but subsequently using the router as its update driver.

  -J' checked the Disk Manager, and he's not here.

  -J' checked Device Manager, it is detected as "Internet access server" (maybe the reason a router driver has been used).

  -J' tried to uninstall the server "Internet access" and restart the system to flush it out

  -The Office again the HDD detected as "Internet access server.

  -J' checked BIOS and it is clearly detected as external WD HARD drive

  After all this I tried on the laptop. No problem and did a reformat of the hard drive so that it can be detected as a disk of expenses by the office. Still no luck.

  Hope someone can help me here.

  Thank you

  Perry

  Hi Perry,

  First of all, check Device Manager to see if the WD hard drive status.
  Right-click on the device and click Properties to check the status of the device.

  Try to connect the WD Passport to another USB port.

  Kindly, follow these methods and check if that helps.
  Method 1:
  Try the Fixit from Microsoft Hardware:

  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/en-us?WA=wsignin1.0

  
  Method 2:
  If this does not help, try to rescan the disks in disk management.
  a. right click "my computer".
  b. click 'manage '.
  c. Select 'disk management '.
  d. click Actions and click 'analyze disk '.
  e. find your player in the list in the lower pane. Right click and select "Initialize" and "Add partition".

  Method 3:
  If none of the steps help, then remove and reinstall USB controllers.
  a. disconnect all USB devices except the keyboard and mouse.
  b. click on the Start button.
  c. type devmgmt.msc and press ENTER.
  d. in the Manager device scroll down to USB controllers.
  e. right click each one, one at a time and click Uninstall.
  f. restart your computer now, each USB port is reinstalled.

  Now test the question.

  Let us know if it helps. If the issue persits, we will be happy to help you.

• Transfer VM for drive external HARD

  Hello

  Like the title says im a beginner when it comes to VMware. Just started new job and learning more about it all day.

  I've been responsible for transferring a virtual machine to an external HARD drive so we can send a company to the United Kingdom to support some software on it.

  The virtual machine is online at the moment and is used.

  How can I make a copy of it and transfer it on an external HARD drive, so I can package it their?

  I thought about clone to the model using the VI client can find where it is located and copy it to the external HARD drive. Would this work?

  Thanks for any help and sorry if I have not provided enough information.

  as a quick fix, you can even copy the virtual machine files in the virtual machine folder in the data store place on your hard drive and then to destination copy in another store data and then make a right click and add the virtual machine to inventory, or create a new virtual machine without the files on disc and use the option 'use existing disk files' to add files from your drive that u copied and then turn on the virtual machine

• External Toshiba HARD drive not recognized on USB 2.0 ports, but only on USB 3.0

  Hello

  I have a Toshiba drive external HARD 750 GB USB2.0/USB3.0
  Now, this HARD drive is not recognized on USB 2.0 ports from my laptop (same thing on my desktop computer) but only on the USB 3.0 port.

  I have try on port USB2.0 computers different (desktop, laptop) but it doesn't work. The LED is the lightning, but the drive does not appear in the file Explorer.

  You have any ideas?

  Thank you

  > Now this HARD drive is not recognized on USB 2.0 ports from my laptop (same thing on my desktop computer) but only on the USB 3.0 port

  USB 3.0 port 900mA feeds. The USB 2.0 port common provides 500mA.
  I think that the HARD drive needs more 500mA power in order to work properly.

  So if you want to use the HARD drive on USB 2.0 ports, I recommend you to use a USB Y cable which allows to connect the HARD drive to two USB 2.0 ports

• PC stopped recognizing 3.5 hard drive external Toshiba

  Hi all

  I have a 3.5/250 GB Toshiba hard drive external. I use Windows XP as my operating system and for some reason, my PC stopped recognizing saying 'USB not recognized '.
  It is supposed to be taken & play and I'm sure that I didn't have a driver, when I installed it.
  If anyone can help or has any suggestions, I would be grateful.

  Thank you

  Malc

  Hallo Malc

  It is possible that you have removed the external device without using the option remove the device safely. Restart the machine and try again.

  Otherwise, you can remove all ports USB device manager and start option to add material on the list. After detection and installation it should work again.