My HDX9000 notebook slowed after BIOS update

Similar Questions

• Unknown device on the Satellite A100-153, after BIOS update to 5.1

  ACPI\TOS1901 * TOS1901<--- this="" is="" the="" unknown="" device="" after="" bios="" update="" to="" 5.10="" on="" my="" satellite="" a100-153="">

  Vista now shows it in as unknown device manager; the TOS1900 showed up too, but after installation of Toshiba Value Pack for Vista, it went.

  Help, please. WHICH IS: ACPI\TOS1901 * TOS1901

  Hello

  ACPI-> Advanced Configuration and Power Interface
  ACPI defines hardware and software interfaces that allow focus on the OS configuration and power management to enumerate and configure motherboard devices.
  For example: ACPI is necessary for the standby and hibernation mode.

  Now your question; the new BIOS has been updated and configured to using VISTA.
  It seems that VISTA was not compatible with the previous version of BIOS because the ACPI interface. Now you can install Vista on the laptop, but it seems that you need a driver. Possibly new chipset driver version might help. But as you probably know, the drivers are not available at this time. Unfortunately

• Satellite L450D - 13 X - blue screen after BIOS update

  I have the blue screen after BIOS update. Satellite L450D - 13 X worked ok before that ideas?

  Is there contact information for Support TOSHIBA?

  Hey,.

  > Is there any TOSHIBA support contact information?
  No, becaue, must contact an authorized service provider. Guys can help on any hardware and software problems and can also order spare parts from Toshiba.

  Here is a list of aspic, where you can look closer:
  http://EU.computers.Toshiba-Europe.com/innovation/generic/ASP_SUPPORT

  Good luck! :)
  ?

• Notebook G71 won to boot after BIOS update on HP site

  I just updated the BIOS on my notebook G71... I downloaded the update from the HP site and it has been updated V20 to V23.

  After the update, the system became an automatic restart and now it does not move before the initial startup screen that shows HP and "ESC to return to the Start Menu" logo at the bottom. I tried the ESC key, but nothing past then is except that it says "esc... pause start." Nothing anyway. Now I can't reboot my system and it is dead. Help, please. Steve

  Unplug the power cord, remove the battery, hold the power button for a total of 30 seconds, connect AC only, see if it will load windows now.

• PAVILION NOTEBOOK 15 K7Q21EA #: SCROLLING WINDOWS PROBLEM AFTER BIOS UPDATED 10 (08/03/2016) PAVILION 15 YESTERDAY 16/10/2016

  CANNOT CONTROL THE SCROLLING. CURSOR DOWN TO THE LOW WHAT MAKES IMPOSSIBLE TO SAVE TO A FOLDER

  Hi @STICKMAN5124,

  Nice day! Thank you for your participation in the Forums of HP Support! It is a great location to get resolutions and interact with experts from the community. It will be a pleasure to help you.

  I saw the post and understand that after only a bios updated cursor drops down due to a problem of scrolling.

  Impressive work, do the update of the bios. Kudos to you for this. It is a privilege to work with tech-savvy and technically competent customers like you and we greatly appreciate your business with HP. You have been great to work with.

  Please check in F2 diagnostics if the scrollbar works correctly. If Yes, then you can update the chipset drivers and http://hp.com/drivers touchpad drivers you can also consult with a mouse external further isolate the issue.

  You can also run diagnostics on the touchpad from this link by going to the UEFI F2 diagnostics: http://support.hp.com/in-en/document/c03467259 please run the complete components. If any component fails, please note the failure code. This is done to determine if the problem is hardware or software partners.

  If it passes and scrolling works very well, please perform these updates. If you are still having the same problem on page F2 UEFI (screen) then you could roll back bios after performing a hard reset. Link for the hard reset: http://support.hp.com/us-en/document/c01684768

  • Please perform this step to roll back bios.  Hold down the "Windows" key and the letter "B" at the same time, then press the power also button for about 5 seconds at the same time.

  I hope this helps. I would like to know how this happens. I hope the problem is solved without hassle and the unit works very well.

  Just to say thank youPlease click the ' Thumbs Up ' button to give a Kudos to appreciate my efforts to help me. If it helps, Please mark this "accepted Solution" because it will help many other people with the same problem to get it resolved without hassle.

  Now carefully and have a wonderful week ahead.

• Re: Satellite X 200 - 20F - slow pace after BIOS update

  Hello!

  I have a Satellite X 200 - 20F bought about 4 years ago. I changed the bios 2.70 recently and I had a problem when I play games:
  The performance of the laptop suddenly decrease after a few minutes of play. For example, when I play Fable 3 + or + + Duke Nukem Forever + the framrate goes to 10-15 fps of 40-50 fps. I need to restart the game to correct this, but even that, the problem come back...

  I used version 1.40 BIOS and no problem.

  What should I do?
  You have one advise?

  Thanks in advance,
  Direct them best.

  Hi Crowzer,

  I m wondering that you did a BIOS update if you didn't have any problems before

  I can only imagine that a BIOS setting is different now. So I recommend to load the default settings in the BIOS, then save & exit.

  Try also to update your display driver. You can find the latest version on the official page of Toshiba also.

• Satellite Pro P200-15W: after Bios Update 1.90 incredibly noisy fan

  Hi, I have a Toshiba Satellite Pro P200-15W, I recently made an update to BIOS version 1.9 and seems to have been a big mistake.
  After restarting the computer, I had a lot of software deconfig and the fan has become incredibly noisy.

  I have the problem with the Toshiba Vista registration software, I get this message: "registration of Vista has stopped working". I read other discussions, I don't want to just disable it in the start.ini file, I would actually solve the problem if there is a way.

  Is there a way to change the configuration of fans? I read a post from Toshiba on another model of laptop that has had the same problem of noisy fans after an update of the BIOS, they gave that a solution with a new version of the BIOS, is there a way to reverse the BIOS to the previous version? (recovery CD will be useful for this purpose)?

  See you soon

  Edgard

  Hello

  It seems that the picture of the fan was changed and renewed in the new version of BIOS, and so fans run fall.
  Why the table fan has been changed?

  Well, usually something like this is necessary to improve the reduction of the internal temperature while the CPU and GPU are running with maximum performance.
  This helps to prevent the equipment from damage!

  Usually, the recovery CD formats the whole HARD drive (partitions too) and installs only the image of Toshiba on the notebooks of HARD drive.
  The image contains the OS, drivers and additional software and has nothing to do with the BIOS update.
  But you can try to recover the laptop to see if you can solve the problems of software as "Vista record"!

  If you want to reverse the BIOS, you will need to contact the ASP in your country!

  Sorry, but all I can suggest.

  Best regards

• Satellite L750 - Bluetooth does not work after BIOS update

  I am preparing some L750 notebooks for use and accept updates from the Toshiba, which included an upgrade of BIOS v1.70 for v2.00. He appears after this update occurs that Bluetooth no longer works, i.e. try to install Bluetooth Toshiba stack will fail as it is said that the Bluetooth radio is disabled and must be turned on for continue.

  As the L750 (model PSK1WA-0C300R) is not a hardware switch to enable or disable the Bluetooth/Wi-Fi, the only option available (Fn + F8) is unsuccessful. I ran a recovery of factory default installation and Bluetooth still does not - resumption of classes does not restore the BIOS to the previous version. I have 5 of the model and confirmed the update of the BIOS is the cause. Two laptops now have v2.00 and Bluetooth has been tested in the work before the update of the BIOS.

  If Bluetooth is not critical for the environment which I deploy these notebooks, it's an annoyance I want to solve. My questions are: has anyone encounter the same problem and managed to resolve it? Is there a BIOS v1.70 available for download to restore the functionality? Y at - it an update of the BIOS > V2.00 for solve the problem I have? Thank you.

  Hi JasonL750,

  Load default settings after updating the BIOS? Go into the BIOS, press the F9 key to load the default settings of the installation. Also, make sure that Bluetooth is enabled in the BIOS if there is such an option.

  In addition, it would be interesting to know what happens if you use the FN + F8 key combination. Don't you see that he has an option to turn on Bluetooth and if so what happens if you do this?

• Satellite A500 emit after bios update 1.50

  Hey guys and girls,

  I have some problems after the update of the bios. Before the update my laptop has been the scene of much smoother and everything was fine and dandy until Tempro told me to update my bios. The problem is that after the update, the temperature seems to be considerably higher as usual when I play the game (I am a gamer) and also all the games I play seems to be much slower than before (lower, gal frame rate). Before the update I could play Dragon Age Origins with 1366 x 768 with 4 x anti-aliasing and the only one that I could get the same performance with the graphic parameter above is on 800 x 600. Now, it is certainly a big problem for someone who is a graphics junkie when it comes to games.

  * What do you think I should do? *

  A. downgrade my bios for when I bought everything first? (I don't know what version of bios is if anyone knows the stock bios?)
  B. perform HARD drive recovery?
  C. clean install of Windows 7 64-bit?

  My laptop computer spec:

  Model name: Satellite A500
  Part number: PSAR3E-00N005EN
  Serial number: X9206227K
  OS version: Windows 7 64-bit Home Premium edition
  BIOS version: 1.50
  Physical memory: 4096MB RAM
  Graphics card: NVIDIA Geforce GT 230 M

  Any help with this is greatly appreciated.

  Post edited by: Poyzen

  Hi mate

  I think you had a version of BIOS 1.30
  In older versions of the BIOS update are not available on the Toshiba driver download page. Only ASP (partner) has access to these early BIOS versions

  In any case, I found an interesting thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=50577

  Not sure if it could be useful but check

  PS; the graphics card driver update is a good idea it too check

• HP Probook G3 450: Start slowly after bios update

  Hello everyone,

  I am a new user of laptop Hp so I need your help, I want to thank you for your time to read and help me with this problem.

  Yesterday, I updated the bios Hp SoftPaq Download Manager recommendation. Progress to succeed and the result of this action made my laptop boot really slowly. The first time, it took just 10 seconds to start windows 10 compared to more than two minutes after the update of the bios.

  I've already searched google for help, but it still does not originally.

  Please help me with your experience on it, I really appreciate all your help.

  Best wishes

  NewHpUser256

  Assuming that this PC came with the edition of Win10, all I can guess at this point is the default setting for FastStartup is in conflict with the new version of the BIOS.  It is a new form of hibernation which is supposed to speed up your boot process, but in some cases, it actually slows down.

  There are two ways to disable FastStartup Win8/10; (1) via the control panel and (2) through a command prompt high.
  
  Control Panel - open Control Panel-> Power Options.
  Select ' choose what buttons power. "
  Select "change settings that are currently unavailable".
  At the bottom of the window, under stop settings, uncheck the box about quick startup
  
  High - command prompt run the following command:
  REG ADD "HKLM\SYSTEM\CurrentControlSet\Control\Session Manager\Power" v HiberbootEnabled /T REG_dWORD 0 f d
  
  In both cases, restart Windows.

  If this doesn't fix it, there is something to play and while this PC is still under warranty, you should contact HP Customer Support directly so they put you in contact with HP Tech Support to see what they can do on the diagnosis and repair of your machine remotely.
  
  I did recently, and HP technology was able to remotely access my PC on the Internet and to make the necessary repairs.
  
  If you live in the United States or the Canada, details are on this page: http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1
  
  If you live elsewhere, contact details are on this page: http://www8.hp.com/us/en/contact-hp/ww-contact-us.html
  
  NOTE: once you get through, stay on the line until you are finally able to talk to someone ' one - it can take a while!
  -------------------------------------------
  However, HP customer care is generally not available on weekends, so you may have to wait until Monday to contact them.
  -------------------------------------------

  Good luck
  ========================================================================
  I'm a volunteer and I do not work for, or represent, HP.
  ---------------------------------------------------------------
  If my post helped you, please click on the Thumbs-Up symbol on my post to say thank you.
  If my posts resolved your issue please click "accept as a Solution.
  ========================================================================

• Satellite U500 - 11G - noise of the fan speed after BIOS update

  Hello

  I have the Toshiba Satellite U500 - 11G.
  I've recently updated the BIOS because my CPU fan did not work under Ubuntu,
  But after the update, my CPU fan speed is faster then normal and make a lot of noise (even if the CPU is cool) when I use Windows 7 is still stay on fast speed making a lot of noise.

  Do we sort of degrading the BIOS or thw way to earn the slow CPU fan speed?

  Concerning
  Sagar

  Update BIOS because of Linux? You know that Linux is not possible on this laptop model?

  In any case, to reduce the fan sped Please reduce the cooling in saving settings method.
  Control Panel > Power Options > go to your preferred power plan settings and choose advanced power options > Toshiba saving settings > cooling method > set to optimized battery.

• Failure of starting in B50-30 Touch after BIOS update

  Hello

  I bought a B50 - 30 touch notebook 2 months in the United States.

  Just before my visit to India, I have updated the BIOS to version 2.04 to 2.07.

  Now I am unable to boot successfully in the factory-installed Windows 8.1.

  The Lenovo logo & the system gets stuck in a reboot loop.

  I have reset the BIOS for the parameters by default in the system, but still failed to start successfully.

  Even using the Novo button for system recovery results in endless reboot loop.

  Kindly let me know if there is anyway that I can Flash the BIOS to version 2.04 using a USB flash drive.

  I have both versions 2.04 & 2.07 of the BIOS update utility executable files:

  http://download.Lenovo.com/ibmdl/pub/PC/pccbbs/mobiles/ziwb0207.exe

  http://download.Lenovo.com/ibmdl/pub/PC/pccbbs/mobiles/ziwb0207.txt

  http://download.Lenovo.com/ibmdl/pub/PC/pccbbs/mobiles/ziwb0204.exe

  http://download.Lenovo.com/ibmdl/pub/PC/pccbbs/mobiles/ziwb0204.txt

  Any help in this regard would be greatly appreciated.

  Until I got back to the States after 3 months of waiting, is not a pleasant option.

  
  

• Portege M800 no boot after BIOS update

  Hello

  I encountered some problems with my netbook (Portege M800-10W) after the BIOS update.
  The update of the BIOS program appears failed. Then my Netbook automatically rebooted and now I can't start my PC more.
  All the LEDs will light up but the screen remains black and after a few minutes, the beep 3 times (1 long, 2 cm) netbook.

  How do I restore the BIOS to the previous version (or plant)?

  Thank you.

  Adrien

  null

  Hi Adrien

  I think that Akuma is right. Your laptop must be verified by the service of Toshiba s. Let check your laptop and I hope they will help you with this.

• Satellite C55-A-16Z - graphics card does not work after BIOS update

  Hello

  I have a portable Satellite C55-A-16Z with windows 8 and a Nvidia geforce 740M graphics card.

  Last week he asked me to update the version of the bios at 1.30.
  The bios update was successful.

  However when I restarted my laptop I started having a BSOD dgxkrnl.sys.
  Correction of the error and restarted for an another BSOD Windows, and after the second solution, I stopped making BSOD.
  But now, I noticed its games running, if not use the dedicated card, but use the 4000 Intel.

  In the settings Nvidia dedicated card is configured to be always on.
  It seems that my card is missing, but it appears in Device Manager.
  I tried to delete, update the drivers and the default factory reset, but nothing helped.

  Also, when I go into Options power the Intel card is listed and when I disable the card intel in the Device Manager it starts to use the graphic viewer for windows.

  How can I get my Nvidia card to work again?
  Any help is appreciated.

  Thanks in advance.

  Hello

  After the BIOS update the BIOS should be set to default settings.
  You can do it in the BIOS.

  In addition, you mentioned that Windows 8 is still installed on your laptop.
  8.1 to win has already been published by Microsoft and I highly recommend that update you the system of 8 to 8.1 Win Win.

  Before you start the upgrade to 8.1 win, you should check and read the instructions step by step for Toshiba: http://www.toshiba.eu/innovation/generic/windows8_1-message/

  I guess that after the Win 8.1, nVidia graphics card upgrade works well also.

  Your comments would be greatly appreciated.

• Satellite C650 - black screen after BIOS update

  My Satellite C650 Windows 7 - won't start afte BIOS update / switch.

  Everything worked very well until the automatic update of Toshiba asked me to download and install the new BIOS update, I did. At the same session Windows and McAfee asked updated. I agreed to all. After all updates have been installed, turns off. The next day when I walk, I see only black screen. I also tried F2, F12 and drive recovery. Nothing happens!

  Any recommendation?

  Hey,.

  It seems that something was wrong during the update of the BIOS and so that you can t the computer unbootable. But I put t understand why you did the BIOS update. If everything works correctly, you can forget about this update. More if you do a BIOS update you shouldn't t run any other updates or programs that might affect the update of the BIOS.

  Anyway, in this case you can do nothing and you need professional help. Please contact an authorized service provider and guys can help you update the ROM module On the Web from Toshiba site, you can find a list of all the FSA:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  Good luck! :)