My hp photosmart C4680 will not go into stand by mode

Similar Questions

• Print job Photosmart 8180 will not delete. Printer error mode.

  My 23 page stopped Mid-page print job short of 9 pages. I tired to restart that has not worked. I then went to cancel and he says that the deletion but it is not. It will not have any other impression. It says 1 document in Quebec and printer in error mode. How can I delete the job?

  Hi Gingercoconut,

  I see by your post that you are unable to delete the job stuck in the print queue.
  I'll be happy to help you.

  I've included a URL to find out how to restart the print spooler and empty folder of spooling print to delete the job stuck in the queue. How to clear the current queue in Windows Vista & Windows 7.

  You will need to go back and try and delete the task in the queue again.

  If you're still having problems, then restart the computer.

  What operating system do you use? How to find the Windows Edition and the Version on your computer.

  I hope this helps.

  Thanks for posting on the HP Forums.
  Good day!

• HP Photosmart C4680 will not print or copy

  Hi all

  My printer does not print (the document is sent to the print queue, but is never printed) and either copy (it just says: "copy" on the screen, but it never does).

  It has been a few months since I use it, but it worked perfectly the last time I did...

  Any suggestions?
  Camy

  Hi Camy_A,

  Thank you for your answer!

  I would try first with our HP print and Scan Doctor .

  So, please take a look at this guide. Printer does not print after upgrading to Windows 7.

  You see another error message when you try to print or copy?

  Hope this information helps and have a great day!

• My analysis of the HP Photosmart C4680 will not open

  Cannot open the Scan00001

  Download Adobe Flash Player. When I switched from Windows 8.1 for Windows 7 Home Premium, computer repair people not to download. It works fine now.

• my hp photosmart c4680 will not print over the network

  I set up the printer on a computer (it prints fine from there) I then shared it on the local network. When I try to print other computers it is said print, computer, it is connected to the so-called print and thus made the printer. but nothing prints help!

  NVM, I thought about it myself. instead of simply cancel the print through the computer job, that I had to cancel the print job directly to the printer. weird.

• S2409W, setting HDMI will not go into power saving mode?

  So I searched high and low on these forums of the Dell Community (and other sites) and I've not seen this documented problem. The problem I have is when I plug the cable HDMI to computer (Tower slim 530) to my s2409w, I get a nice clear picture and everything works as expected, until I put the computer in standby mode.  The computer sleeps, but the monitor turns off almost as if he was going to sleep, but then display Saver screen default monitor that says "hdmi cable does not exist.  What I was expecting the screen to go to power save mode. When I use my DVI or VGA cable and put the computer to sleep, the computer and the monitor switch mode 'sleep' as expected.  This problem only occurs with HDMI. I tried setting the screen "automatic detection" and "hdmi" for the selection of cable and no work to put the monitor to sleep. Anyone has a solution, or similar experiences?  I've seen a lot of posts on power audio hdmi save the problem, but not with this one.

  -Thank you

  I know this is an old thread, but I had the same problem with another Dell monitor and a homemade computer.  In another thread, someone said that some cables HDMI I have this problem, and others do not.  I just wanted to confirm that it IS THE CABLE.

  I swapped HDMI cables with my TV.  The TV had a cable older and thicker.  Immediately after that, the monitor will now sleep just right.  What I can guess is the skip of thin cables really cheap make the connections required for this feature since the TVs didn't have standby mode.

• Why my computer will not go into screen saver mode, the settings are defined in law?

  Hello, I just rebuilt my computer. I run windows 7. I can't get my pc to go to screen saver mode. I run a Gforce 7800 graphics card, also

  I can't get my system to go in sleep and Hibernate, unless I do it manually. I checked all the settings and everything seemed ok.

  My drivers are all up to date. My email addy is * address email is removed from the privacy *.

  Thanks for your help,

  RSPRING

  Hello

  1 did you change on your computer?

  2. what happens when you try to change the screen saver?

  Method 1:

  Open the troubleshooter of power

  http://Windows.Microsoft.com/en-us/Windows7/open-the-power-Troubleshooter

  I suggest you to follow the steps and check.

  1.	Open settings screen saver by clicking on the Start button, clicking Control Panel, appearanceand personalization, customization, then screensaver.
  2.	Under screen saver, in the drop-down list, click the screen saver you want to use.
  3.	Click Preview to see what your chosen screen saver will look like.
  4.	Click OK.

  The screen goes black when the monitor is set to mode 'Sleep' through the Power Options.
  Here is a link to some information about your Power Options settings:

  http://windowshelp.Microsoft.com/Windows/en-us/help/495c2226-19F1-49EB-9FD8-6dd7f2c0b49e1033.mspx
  Method 2

  I suggest you follow the links and check out them.

  Sleep and extended: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/sleep-and-hibernation-frequently-asked-questions

  Turn off a computer: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-off-a-computer-frequently-asked-questions

  Windows 7 is not going to sleep

  http://support.Microsoft.com/kb/976877

• Software HP Photosmart C4680 is not compatible with Windows 7

  I recently updated my HP Pavilion DV5-1138-nr laptop to Windows 7. I managed to reinstall all my software, but the software on the drive for the HP Photosmart C4680 will not install. I have no problem to install the drivers because they have already integrated into Windows. But it would be nice to have software that tells me when the ink will run out, so I know when to buy more ink. Basically, it says that I can not install this software in "Run As" mode... ", which I am not. He says I need to be connected to an Administrators account, but I am logged in as one. If anyone has any ideas, please let me know.

  Thank you.

  Message edited by cpuman216 on 10/31/2009 08:58

  cpuman216 wrote:

  I recently updated my HP Pavilion DV5-1138-nr laptop to Windows 7. I managed to reinstall all my software, but the software on the drive for the HP Photosmart C4680 will not install. I have no problem to install the drivers because they have already integrated into Windows. But it would be nice to have software that tells me when the ink will run out, so I know when to buy more ink. Basically, it says that I can not install this software in "Run As" mode... ", which I am not. He says I need to be connected to an Administrators account, but I am logged in as one. If anyone has any ideas, please let me know.

  I suggest to disconnect the printer from the computer, uninstall the drivers, then download and install the driver HP recommended here.

  Edit by Katie_H (30/03/11): fixing broken link

• HP Photosmart 3210 will not install on Windows 7 Pro 64 bit.

  HP Photosmart 3210 will not install on a brand new desktop running Windows 7 Pro 64 bit.  I downloaded the latest software, and when I run it, the installation window disappears shortly after it starts.  No error message.  I ran into several related issues lately.  I can't install a ScanJet 5590 on a new laptop running Windows 7 Pro 32-bit.  Said it ends, but nothing is installed.   Could the fact that there are other HP printers installed on these computers (network printers) installed using driver only before attempting to install the software cause problems?  I spent hours trying to solve these.

  OK, much better progress!

  If the software is always installed, tell him you'll connect later.

  Go to devices and printers, look for the printer here, make sure you that no documents waiting to print and delete the printer if it is there.

  Then go into Device Manager and remove all photosmart series 3200 drivers you find, you may need to click displays hidden on the view menu.

  Thirdly, go back to the devices and printers. Select another printer, as the writer XPS comes with Windows. Along the top, with adding a device, add a printer, print server, you will see properties. What to choose and go to the tab drivers. If you have the HP drivers in there you do not, select them and choose delete and "delete the driver only."

  Now restart and go to your Start menu and your HP folder. You must have installed the software, just no device driver, select "add a device" or "printer setup and software." Installation should complete without problem.

  One last thing, you must temporarily turn off firewall and antivirus installation, in which case he mistakingly tries to block the attempt to install.

  Good impression!

• Photosmart 6525: will not print in black

  My photosmart 6525 will not print in black ink.  Clean the printheads 6 times. Cartridge replaced twice. Any suggestions?

  Hello

  Welcome to the Forums of HP Support! I see that you are having problems printing in black. I want to help you solve this problem. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  Try the following steps to see if it will solve the problem, HP Deskjet 6520, printers HP Photosmart 6520 - printer prints a blank Page or doesn't print in Blac...

  Here is a document to manually clean the contacts of the cartridge, "not compatible ink cartridge" or "specified ink cartridge needs to be replaced" views for HP Deskjet i...

  Do not take into account the title.

  Here is a document for the reset of the printer. Ignore the title, HP printers - solve the 'problem with printhead,' "The printer failed," 'Ink system failure', or ' 0 x. / c0 > »

  Please let me know the result and if there is anything else I can help you. Thank you.

  

• HP Photosmart d110a will not scan.

  HP Photosmart d110a will not scan.  The resettled drivers, checked, put off - tension, nothing works.  Using Windows 7.  Error message is ' try scan from computer or see the documentation.

  Hello smhbcd

  The current software and try to reinstall using the latest drivers from the website. The link below will take you to the page "Select your operating system". Do it and download the latest driver full features.

  Photosmart D110 software

• My computer will not go into Hibernation mode. I checked the hibernation mode. But when I close the laptop, I get a message saying prepare to Hibernate.

  My computer will not go into Hibernation mode. I checked the hibernation mode. But when I close the laptop, I get a message saying prepare to Hibernate.

  Hello

  1 I want to erase the General corruption and repair/replace damaged/missing system files:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ============================================

  After the foregoing: a Fixit for Hibernate

  How can I enable hibernation on my Windows Vista computer?
  http://support.Microsoft.com/default.aspx/KB/929658

  How to reactivate the lack of Hibernate Option in Windows Vista?
  http://www.askvg.com/how-to-re-enable-missing-Hibernate-option-in-Windows-Vista/

  -------------------------------------------

  More if necessary:

  Check your settings (BIOS/CMOS) - usually F2 as you start - Wake on Lan, Wake on Modem and so on.

  Troubleshooting Windows Vista sleep and extended
  http://www.computerperformance.co.UK/Vista/vista_hibernate.htm

  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista
  http://support.Microsoft.com/kb/950686

  May need to reset all to default power settings and then place back as you prefer.

  How to solve a problem of Mode for Vista and find a Solution
  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

  How to enable and disable Hibernation - you can try to disable and re-enable the it. http://www.Vistax64.com/tutorials/165508-hibernation-enable-disable.html

  How to restore the default power in Vista (and then go back and change as you wish)
  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  Panel configuration-Device Manager - look at the settings for the network card, WiFi, Modem power management.
  and other devices. (Double click on the device and the power management tab)

  Panel configuration-Control Panel Home view (non-conventional) in the top-right search pane
  type of hibernation - see turn Hibernate on / off

  May need to reset all to default power settings and then place back as you prefer.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• How can I recover a .ts file that will not import into Movie Maker? The .ts file works fine in Media Player... help

  How can I recover a .ts file that will not import into Movie Maker?   The .ts file works fine in Media Player... help

  Hi Stuart,

  We understand that you try to import a .ts file to Windows Movie Maker. However, Windows Movie Maker does not support this file type. You can click on the link below for more information on what file types are supported by Windows Movie Maker:

  Can what types of files I use in Movie Maker?

  Kind regards.

• empty folder named "enteral" will not go into the existing folder on desk too long because "Path of Destination."

  Make an empty folder to simplify the example of this problem recently of news. Everything I do, even a single word names, will not go into any other file with this next window: "Destination path too"

  long. "

  The file names (s) would be

  be too long for the

  destination folder. You

  can shorten the file name
  and try again, or try a

  location with a

  shortest path.

  Hello

  Welcome to the Microsoft Community Forums.

  Looks like you get an error message "the file (s) would be too long for the destination folder. You can shorten the file name and try again, or try a location with a shorter path.

  This normally occurs when the file system is corrupt.

  I suggest you scan the computer for the error. Follow this step to do the same thing:

  1. click on start
  2. type: CMD, according to the results, right-click CMD-> click 'run as administrator '.
  3. at the command prompt, type: chkdsk /r

  When you restart your system, your computer will be scanned for errors and will try to correct them.

  Note: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  In addition, you can consult the following link for more information:

  Check a drive for errors

  Hope this information helps. Get back to us with more information so that we can help you.

• HP C4680 will not remove jobs at the end then freezes in queue on MAC with the Mavericks

  HP C4680 will not remove jobs at the end then freezes in queue on MAC with the Mavericks

  try to download the latest driver Package HP from Apple here:

  http://support.Apple.com/kb/DL907

  Install the package.

  Reset the printing system.  And add the printer with the new driver.

  Try to perform a "reset printing system" on the Macintosh and then reconnect to the printer.

  To reset the printing system do the following:

  1. open System Preferences
  2. click on Printers & Scanners
  3. right click or control click in the list box for the current print queues.
  4. Select the Reset printing system...
  5. enter admin user name and password
  6. restart the Macintosh
  7 try to set up the printer again