My "Laptop" no longer works after installing Bios 1.9

Similar Questions

• My CD/DVD drive no longer works after installing an update for Roxio Burn, (it was working perfectly until after the update).

  Hi, my CD/DVD drive has stopped working after I installed an update for Roxio Burn. I tried uninstalling and reinstalling, updating all windows and my device driver programs, but I just comes up with one, "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) ', warning. The DVD/CD player that I use is called TSST corp DVD +-RW TS - H653G

  Hello

  Code 39 means that the driver is corrupted or missing.

  Having too many CD/DVD programs can cause strange problems, especially if they're loading of parts of them.
  Selves at the start because they will be competing for resources. This does not mean that this problem was caused by
  These however is a possibility depending on which and how many you have installed.

  Definitel check with the help of Roxio and their forums - you may need to uninstall Roxio to see if this
  allows the reader to work (not re - install until the issue is resolved).

  -------------------------------------------------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ==========================================================

  After the foregoing:

  References to Vista also apply to Windows 7.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The DVD player does not work after installing Windows 7
  http://support.Microsoft.com/kb/975270/

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry settings for your
  CD/DVD drive someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays
  all devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• His Dell Inspiron 1420, microphone and camera integrated into the laptop does not work after installing Windows 7 Professional

  No sound from my Dell Inspiron 1420 and the microphone and built-in laptop camera do not work after installing Windows 7 Professional 64-bit. My laptop has Windows 7 Vista 32 - bit family premium. My laptop is 64-bit capable and after going through the Upgrade Advisor, I installed Windows 7 64-bit. I can hear sounds when I use a headset plugged into the line-in Jack, but not through the speakers built into the laptop. I already tried new drivers from the Dell website, but I could not find.

  Any help will be much appreciated. Thank you.

  As it is has no drivers 64 bit Windows 7 on Dell Web site, your best chance is to install the 64-bit versions of Vista (if they exist) in compatibility mode, viz:

  Right click on the Vista driver, then select Properties > Compatibility tab. Now choose to run the program in Vista compatibility mode and then apply > OK. Right click on the file and select run as administrator to install it.

• Touchpad no longer works after update BIOS on Satellite A500-1GL

  Hello world

  I just bought my laptop Satellite A500-1GL today. I started at the top and plays a bit (nothing serious). The touchpad worked very well at the moment.

  Then I discovered this tool to update the material and the update of the BIOS that worked without any problems. After I restarted the laptop, BIOS, loaded the default values of the installation and recorded.
  After that Windows 7 (x 64) started the touchpad no longer works...

  I downloaded the driver here and installed again once, still does not. I went into the BIOS, disabled the touchpad (I thought that maybe it's a bug...) and started again. It still does not...

  I enabled it again in the BIOS, tried to push the function + F9, but it still does not... Finally, I used the recovery and installed a Windows 7 costs.
  But unfortunately it still doesn't.

  Now, I'm out of ideas, can anyone help?
  Is there a chance to get the older version of BIOS to downgrade it?

  Thanks in advance ;)

  Hello

  It seems strange that after update Bios touchpad no longer works.

  > Is there a chance to get the older version of BIOS to downgrade it?

  To be honest, I don't know where to find. In any case, do a search on Google. Perhaps, other users of the forum can give you a link to download.
  The downgrade of the Bios is riskier upgrade procedure. So, be careful the next time...
  Advice for the future; Do not touch the running system.

  Good luck!

• Pad at the top of the keyboard no longer works after installing Windows 7

  I have a cl dv7-1273.  Just changed from Vista Home Premium 64 for Windows 7 64.   Win 7 installed OK.  After you install the pad at the top of the keyboard no longer works in the dialogs like this.  When I entered the numbers here I had to use the keypad.  Keys still work in Word, Excel, Evernote, etc..

  Someone on the forum had the same problem of pad during the upgrade to win 8.  They solved the problem by uninstalling Comcast constant guard.   I removed a constant guard and now my keypad work.  Is there something in constant guard that is in conflict with the keys from HP laptop during upgrade to Win 7 or 8 Win.

• My Equium L40 no longer works after update BIOS!

  Hi friends...

  Please, I need a help.
  I updated my computer laptop bios v2.00 v1.60 and after that it no longer works.
  When I try to turn it on nothing happens.

  Maybe I need the original BIOS.

  Who has a solution? What can I do?
  Could someone help me?

  Thank you!

  My laptop is a series of Equium L40 - PSL49E - 156

  Hello

  I can tell what you have to do now
  You will need to contact the ASP in your country for assistance

  Yes, you have the technician ASP.
  I assumed that the ROM module where the BIOS is stored has not properly been flashed.
  I think that the ASP will try again by using a special version of the flash BIOS

  Good luck

• Wireless no longer works after installing OS

  Due to a hardware problem, I had to reinstall the operating system.  I'm running Windows 7 on an Inspiron 9300.  Initially, the PC had XP on it but works Windows 7 for several years and when I tried to reload the drivers from the OEM disk provided with the purchase, I received error messages.  The light Bluetooth enabled / disables the slot and off mode with the FN + F2 but the WIFI light, what has worked before you reinstall the operating system, is no longer lights up.  I can't find that the WIFI in the list of my network.  The driver for the Mobile Intel Chipset or drivers of wireless network will be set up.  I get the message that the operating system is different and on one of the installation of the tent a message that says "OS not found article in the INI (iProInst.ini) file.  Are there drivers available for the wireless network card that works on Windows 7?  The original PC configuration shows that an Intel 2200 Wireless Mini PCI card has been installed.  For any help or suggestion would be appreciated.

  Thank you, Andrew.  I downloaded the driver and it did not work at first.  However, it is ultimately the one I needed.  The I found on the networking forum and the first assignment was labeled 'Read Me First' from a K of Rick in it, he listed the measures to be taken if the BONE had to be fully installed from scratch.  He entered different drivers and the order in which they should be installed.  I found four points of recharge/reinstall in the list, he published and he did it in the suggested order.  The quick set button would not move I received a message from the "is not a supported system.  Setup cannot finish.   The wireless still doesn't work after you install the network driver (R155386) so I scanned the files that have been loaded and are hitched to C:\Dell\Drivers\R155386\XP\Drivers and found the DPInst32 file (there is also a 64 bit one).  It's the driver package installer and after execution of this fact, a series of drivers have been installed and the light launched WIFI.  Once I went to my network implementation and setting up wireless setup, everything works now and I have access to the network.  Thanks again for the answer so quickly and put me on the right track.

  Roger

• CD/DVD no longer works after update BIOS of yesterday

  HP Pavilion dv7-6b55dx

  Win 7 64 bit

  I solved the problem with the audio that created the update, but now to discover that my DVD/CD is unusable.  I don't see the driver available to replace it.  Tried to reinstall the driver I have on my PC and got the error message

  Windows cannot start the hardware device because its configuration (in the registry) information are incomplete damaged (code 19)

  Help, anyone?

  Endy9 wrote:

  I tried a DVD player USB which also cannot use the info registry now damaged on the DVD drive external.  Do you really want everyone (I've seen dozens of messages on bulletin boards, and it's just what I've seen) to believe that it is a coincidence that immediately after installing this BIOS update hardware failed and corrupt just pilots themselves.  Please, I beg you.  We have an adult discussion about this.  The process of updating these registry settings can be affected if the real drivers belong to HP or not.

  If you notify me that I reinstall the BIOS (guess I can do no harm, since I already have downloaded audio drivers to reinstall) the registry information for my DVD will be fixed?

  BIOS do not affect or touch the registry somehow and there is no need to relocate the BIOS but you can reset the default BIOS. You could link me to these forums you're talking and if not. cases are of a scale that is having the same problem, the update of the BIOS can be studied.

  Since you said that even an external DVD drive is also not recognized its certainly a matter of s/w.  Could try to use a restore point was working on your dvd player? I know that you did a restore to a date before you installed the update to the BIOS, but you can try a diff. one?

  In addition, you can restore your BIOS downgrade (F2-System Diagnostics) If you feel/think the BIOS update is a cause of the problem.

• Windows Update or automatic updates no longer work after installing SP3?

  Recently I photographed two XP machines. A a Latitude D600 and also an Optiplex 745 with Windows XP SP2. I can deploy SP3 in our process of the image. First run I did. Once installed SP3 updates no longer work. I found this article KB http://support.microsoft.com/kb/943144 and tried the suggestions here and FixIt MS, no luck. Then I thought why not try again maybe all the trial and error messed up something. I reimage but this time choose to do not to install SP3 immediately. Once done I run Windows Update and it works, until it installs SP3 then is no longer functions. I tried the above steps once again, no luck. I then leave the PC for 48 hours to see if the automatic updates the shot but they do not have. By other suggestions online I wrote a small batch file that updates several components of Windows Update (dll) which made no difference, and yes I'm in the last WindowsUpdateAgent. Please any help on this would be welcome. We move away XP but we have still a few dozen or more systems deployment running XP and this question slows down my work courses as I spend time troubleshooting instead of being able to finish and move along.

  Hello

  I suggest you to download and install Windows XP service pack 3 manually and check to see if the same problem happens:
  http://Windows.Microsoft.com/en-us/Windows/help/learn-how-to-install-Windows-XP-Service-Pack-3-SP3

  It will be useful.

• Thunderbird no longer works after installing security update

  After installing 24.4.0 Thunderbird security update (20140316131045) cannot retrieve or send messages of any of my e-mail servers. There is no error message. I can see new messages through webmail.
  Is it possible to uninstall this security update?

  Make sure that your firewall is not blocking Thunderbird.

• Satellite A300 - Touchpad no longer works after update BIOS

  Hello

  After the upgrade of the bios of my Satellite A300-1NJ version 1.70, the Synaptics touchpad stopped working at all!
  (I tried with ubuntu liveCD check is not a driver problem)

  Older bios is no longer available from Toshiba Web site!

  How can I solve this problem?
  And thanks for the help.

  Hello!

  The touchpad can be validated with FN + F9.
  Check it!

  In addition, try to use an external mouse. It work?

  Good bye

• Satellite A200 - Webcam no longer works after installing Win7 32 bit

  I have a Toshiba Satellite A200-237 and I formatted my hard drive and installed Windows 7 Ultimate 32 bit once.
  I also installed software Toshiba site (camsoft-20070810084209) of this 1.7 version camera assistant...
  I start the program, but when I want to start the cam I get an error with the message of start the cam. I don't really understand the problem and when I loop upward the CAM system is unknown?
  What can be the problem? I have different version of CASES if so where can finance this?

  On my Satellite A300 (supplied with Vista) I installed the latest version designed for Satellite A500 (Vista version) and it works perfectly.
  I don't know if you can use it on your Satellite A200 but you can try it.

  You can find HERE for your model of laptop Win7 CASE
  CASE I used you can find HERE

  Try it. If it does not let us know.

• Existing Web site no longer works after installing OSX Server

  I have a site on my mac mini, who resides in/Library/WebServer.  It has Perl cgi pages, images, css, Javascript files.

  I installed Mac server I can use the mac-mini as a place to for Time Machine on my laptop to save on via wifi.  Now the Web page has moved and has a different configuration, I can't understand. Before I had a directory/Library/WebServer with Documents to subdirectories, CGI-Executables, Lib, pictures and models. Now it seems that the html files live in/Library/Server/Web/Data/Sites/Default, and I have no idea where the other files to go.  Apache does not work either.  Disable the sites option just disables the address of the Web site completely.  Enter http://localhost just gives an error message saying that Internet sites is disabled.

  I didn't change my site, I just wanted the time-Machine capabilies.  I put a lot of work in my site and I would like to recover my TI.

  Not a good situation, unfortunately.    You are either going to learn how OS X Server, or you want to remove OS X Server and perhaps acquire a Time Capsule.  (Ac-class AirPort Wi-Fi devices are also supported on Time Machine.)

  OS X Server expects local DNS to be put in place, you may not use DNS ISP, if you are on a NAT device would have network - and OS X Server expects that you will place your files in the localities of/Library/Server/Web/Data/Sites, or whatever the directory on your web site is stored in a site within the.app.

  In both cases, you will need make your website readable _www.

• Satellite P300D-h-13: Bluetooth no longer works after update BIOS 3.30

  I have a huge problem with my bluetooth module integrated on Toshiba P300D-h-13.
  It worked great until I have not flashed Bios to version 3.30.

  Now, I do not see my module and when I start battery bluetooth, it says that I should plug my camera.

  Plese help me or give me a link to older firmwares bios?

  You define the default BIOS after the update?
  Isn't it? Then do it.

  Have you tried to activate the Bluetooth using the function keys after the update of the BIOS?

  PS: don't think that its probably the Office BIOS issue is related to the other grounds
  What system do you use?

• Microphone no longer works after installing Windows 7 Ultimate

  I recently installed Windows 7 Ultimate on my laptop Acer Aspire Timeline (exact model Acer Aspire Timeline AS4810T-8480 14 inch HD laptop screen). I noticed that once I installed it, my microphone/sound stopped working. I have no problem listening to the audio, but I think that the microphone was affected. When you use Skype, that is the message that appears: "micro problem: there is a problem with the microphone into your computer." Try plugging a USB headset for this call. I know he's had no problem with my microphone before I installed Windows 7 and had been using Skype without problem. Can someone help me solve this problem? Thank you.

  Hi Ana

  Yes, first you recommend to contact ACER to your hardware mic problem.
  try to update your sound driver from device (right-click on computer management<>
  or download the Audio driver from the ACER site
  If persists
  uninstall the Audio driver and install the driver updated again, reconfigure the Mic and test the question.
  I hope that the problem will be resolved quickly
  concerning
  Nikhil