My work of dose't WiFi.

Similar Questions

• problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  Problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  On the Pro iPad, tap settings > general > reset > reset network settings

  You will need to re enter your Wi - Fi password.

  Then try to connect to your Wi - Fi network.

  If this does not help, more available in this support article suggestions > If your iPhone, iPad or iPod touch connects to a Wi-Fi network

• Satellite A110 - switch WiFi does not work with the new WiFi card

  Hello everyone

  I have a problem with my laptop Toshiba Satellite A110 - 178 (PSAB0E). I replaced the original Intel 3945abg with Intel Link 5100 WIFI card and on the new wifi hardware wifi card switch does not work.

  New wifi card is discovered and drivers to the correct job but when I try to search with the Intel Pro/Wireless software wifi networks I message to turn on hardware switch, but there light and not work. The old wifi card swich works OK - orange light is on. On the new map light is off and swich does not work.

  Help, please

  Hello

  Do you have also enabled the WLAN functionality by pressing FN + F8?
  Check it!

  In addition, I think the case is clear: the new wireless LAN card isn't compatible with Satellite A110.
  So in my opinion, you must use remove the new card Intel and install the old card that works fine in your laptop.

• Satellite 4100XCDT: how the IRDA port works under DOS

  I have a Toshiba Satellite 4100xcdt. How do I assign a COM port to the IRDA (infrared) port in the BACK so I can use programs such as Winsamp
  http://www.veg.Nildram.co.UK/remote.htm

  The BIOS assigns COM1 and COM2 serial port to the built-in modem. However there is not a single option for the IRDA port not found.

  How can I make the IRDA port works under DOS?

  In my opinion it of not possible to use the IrDA DOS, because drivers must be installed and initialized.
  The IrDA port driver is a common Windows driver and the irda connection works only when windows was loaded

• How Siri works with a hotspot wifi phone from ATT without data?

  How Siri works with a hotspot wifi phone from ATT without data? I have the hotspot & it recognizes my iPhone5c, but Siri cannot find a connection when I use it. My phone service is now but only phone at & t imessage. No data, unpaid for the text. It works fine on my home WiFi & works but not the hotspot.

  Siri requires an Internet connection

  It will not work without one

• OLE1. CreateEmbed Bit_str, "Paint.Picture" works under Dos but does more when gave birth off the coast. How can I fix teachix?

  OLE1. CreateEmbed Bit_str, "Paint.Picture" works under Dos but does more when gave birth off the coast.  How can I fix teachix?  Using VB5 to obtain a bitmap for embeded in an Access database. This used to work perfectly, but gives an Error 31032 when the program is spawned off the coast.  It still works from a command prompt.  How I have the code around this, or what is the problem?  Help, please. Thank you

  Hi AllisonBlackmer,

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the forum TechNet for assistance:

  http://social.technet.Microsoft.com/forums/en-us/category/windowsxpitpro

  Hope the helps of information.

• Damaged my iPhone 5.  Receipt of replacement and went through the steps of activation.  All transferred very well - I thought.  Now, the phone only works when connected to wifi.  Help!

  Damaged my iPhone 5.  Make an insurance claim and received a replacement.  Has passed through the stages of restore/update / back.  Everything seemed to go well.  However, I can only send/receive texts or to use the phone when connected to wifi.  Saved settings and recontroler.  Nothing works.  Help!

  Hello

  I'm sorry to hear that you are not able to use your cell phone... Well well... like a cell phone.

  I suspect the 'texts' you send and receive through iMessage, not your cellular service provider network. When you look at the top left of the screen, it does not say 'search' or does it see the connect to your provider's network?

  Have you tried the steps If you cannot connect to a cellular or cell - data Apple Support Network?

• express problem airport works as a wired wifi Extender

  I have TW cable for internet in bridge mode and not as a DHCP server.  This is directly related to the port WAN to a time capsule extreme Airport (1-2 years).  The time capsule has a link to 16 port 10/100 netgear switch to one of the LAN ports.  About 3 weeks ago, I added 2 new Airport Express to expand the wifi of my very large House.  I ran the hard lines to the Airport Express as well.  Each express is set to bridge mode and just to extend the wifi network.  The extreme time capsule is the DHCP server.  Everything works fine as long as the couple declares itself to the extreme to the wifi, but this does not solve my problems of scope and speed on the other side of the House that expresses it is installed to cover.

  Problem: When it expresses the airport is not connected I get a ping void 5ms from a computer on the local network to express it and extreme.  Once I Plug one of them in the cable system my time to ping for all devices are very erratic.  From time to time they are in the range 1-10ms, but more often they are in the range of 1-2 seconds and exhale.  Once, I disconnect or hard of the line time to ping back to normal within 5 seconds.

  Troubleshooting attempted so far: even once, I connected one or the other of expresses it to the hard line the problem occurs.  Disconnect it and connect the other the same thing.  Connect them directly to the Airport extreme still same thing.  Connect the express directly to a PC and run ping test, void 1ms response times and no change for the rest of the devices.  Ethernet connected to the WAN port of expresses it instead of the LAN port same question.  Repunched and re made the end of the cable used to one of them, same problem.  Called Apple and they told me it should work, and provided with additional troubleshooting.

  Firmware on all the devices have been updated about 3 weeks after I got them stable on wifi.  Unfortunately I do not have the written down version, but they are all on the same version now.  All devices have a green light on them when just using wifi to talk to the extreme.  When wired in airport utility devices drop the GUI are available intermittently and back.

  Whats to test I can think of to the left: replace the extreme airport time capsule.  Replace expresses it.  Wipe off the network completely and start over from scratch with a factory reset complete.

  Any help would be appreciated, I am amazed as to why it does not work.

  Each express is set to bridge mode and just to extend the wifi network.

  And this... extend the WiFi network... is the problem.  When the Express is configured to "extend a wireless network", it waits a connection without wire of the main router. When an Ethernet signal is applied, this translates a huge feedback loop blocking, network.

  Start over and do a hard reset on each of the AirPort Express devices

  Then for the Setup, use a short piece of spare Ethernet cable... any length will do... and plug it between a LAN port <>- on AirPort Extreme on the "O" WAN port on the AirPort Express Terminal

  Don't forget to make the Ethernet connection before you try to implement the Express. In this way, the "Wizard" will pick up the Ethernet connection and apply the correct settings for the Express installation.

  Use "Wizard" Apple's Installation in AirPort Utility to configure things. When you do so, you will notice that the final configuration screen will indicate that the AirPort Express is set up to "extend with Ethernet', who must confirm that the correct settings apply to the Express.

  

  The first Express is now properly configured. It turned off and move it to the remote location where it is needed. If your Ethernet cables and the Ethernet switch works correctly, so too the Express will work properly.

  Implement the second Express exactly the same way as the first, except him give a different device... as Express2 name, for example... to keep things straight.

• WiFi only works in safe mode

  WiFi worked normally on my Mac Pro and then suddenly yesterday I received signal and an IP address but pages load. Other devices and computers work well with my wifi router. I can also surf the web very well when I boot in safe mode. However, when I restart my computer, then no wifi again. I can then go back into safe mode and get internet. I did no new software updates, installations or router configuration changes that may cause this problem from one day to the other. Anyone have any suggestions?

  Since then, I tried the following:

  -restart my router

  -renew the DHCP lease

  -flushed out DNS cache

  "- removed 4 files of./Library/preferences/SystemConfiguration/" then restarted computer

  -rebooted in safe mode

  -reset the SMC

  -turned off bluetooth

  -hidden "iTunes Helper" elements of opening under my user account. The only listed element.

  http://etrecheck.com/

• GPS (all cards apps) working only on wifi. Not on cell phone

  Hey,.

  for a few weeks now all my apps basedon like waze, cards... Work well when on wifi.

  If I remove (or if not connected to a wifi) wifi gps is not in my position.

  I have the software updated 9.2.1. And I tried to clear all the settings from the network and I even rebooted my iPhone and set up under a new phone.

  It still does not.

  can someone help me?

  Hi Anastasia,.

  If you are having problems with your iPhone's GPS works not when it is not connected to the Wi - Fi, you can try some things to solve problems.

  First, close all applications using GPS and test again.

  Force an app to close the iOS

  Then, I would try restarting iPhone.

  Restart your iPhone, iPad or iPod touch

  Thank you for using communities of Apple Support.

  Best for you.

• R7000 can't get wifi to work

  Ive had r7000 router to call big fees, 2 years work August 23, 2016. WiFi lights are on and white. I have good Internet service. Hardline works fine but no wifi. Fact that it recharges and do reset still no wifi. Devices can see the wifi but says not in the beach. I'm standing in front of her.

  If multiple devices have the same problem it seems then that your router has suffered a hardware failure and needs to be replaced

• Satellite L30 PSL33E - wifi is not working after installing XP

  Satellite L30 PSL33E downgraded from Vista to XP. Everything works apart from the Wifi. Device Manager displays Atheros ar5005g card with yellow exclamation point.

  I tried the driver from this site, but windows does not load the driver as it is not signed.
  I try to reload the driver and the laptop freezes.

  I'm probably something wrong. If advice... soon

  Hello

  First you need to update the Win XP to the last State.
  Very important are the SP2 and al MS patches and fixes after the release of SP2.

  The European Toshiba WLan driver page provides a new Atheros WLan driver which is compatible with the Windows operating system. XP and Vista.
  Check this box:
  http://APS2.toshiba-tro.de/WLAN/?page=downloads

  First remove (uninstall) installed WLan driver and then install the new driver Atheros WLan downloaded.

  See you soon

• WiFi Netgear C6300 works do not with edge of samsung Galaxy s7 and regular s7

  I edge of s7 and regular s7. I have 200 Mbps with time warner and the netgear c6300. It does not properly connect to app store, youtube, oculus magazine etc. Iphones in my house works perfectly, as do my computers and laptops. The s7 phones work fine on other wifi connections, but not at home. Help!

  Samsung has recently released an update and now I'm able to watch YouTube videos and update my apps on the Google game shop. I got my phone from T-Mobile so idk if other phone companies still released the update. I hope it's a permanent solution to the problems and not a temporary as patches that I found here. I don't have the money to buy another router and I just wait for the WiFi problem get it fixed so I can use my home phone.

• Phone will now connect only via wifi to otherwise the web network does not work

  My Motorola xprt is less than 1 week old. At first, that everything worked well. I got internet connection etc. So I connected to my wifi at home and it worked fine, then my wifi secure at work. but now I can't connect to the internet without wifi. There is no 3G signal activity. I tried to help out with a representatitve of Sprint and after trying to make an update to profile 3 times in vain, he recommended I take it into a store and maybe get a new phone. Prior to this, however I tried to solve the problems of the site via a USB connection with the drivers properly installed (I think) and he was not able to detect my camera. Don't I have some settings wrong? I'm going crazy because I like the phone but can not use wifi all the time.

  In fact the question on the data connection helped because I went to my settings and the title of the data management 'enabled data' has not been verified, now everything is ok - I have my 3G back. It seems that the Sprint guy should have just over my settings rather than suggesting that I might need a new phone. Thanks again.

  I have another question, but I'll start a separate discussion.

• Communication satellite U500 wifi switch control does not work

  Hello

  I have problem after update of the operating system from Vista 64 bit to win7 64-bit. The problem is in the wireless communication switch command before notebok. When I was with win vista, it works fine, post off - wifi off and post-wifi on (without restarting). But when I updated to win7 and install all the drivers of toshiba upgrade dvd, my wifi switch works as follows:

  When I turn on notebook with wifi off button - its turned off all the time and the wifi does not work and fn + F8 (shortcut key for wifi) does not work too. I have to restart the PC with wifi switch in position-the wifi works fine and fn + F8 is able to turn on and turn off the wifi. But that put the material do not react to pass and - diode LED is always on (in case when I start the pc with position control on and in the case where is when off wifi LED is not clear and switching does not work).

  I've updated wifi realtek drivers but still it does not work. IAM verry sorry for my English. I was looking into Toshiba diagnostic tool and there is no modem device, but yes, wifi is perhaps problem here?

  Thank you very much for the reply. Tom

  Hello

  Different Satellite U500 (and other models) supports various wireless network cards, and that's why you'll find also different WLan card drivers.

  Your U500 seems to be equipped with an Intel Wlan card and here you can also download the right Intel Wlan card driver for this card:
  http://APS2.toshiba-tro.de/WLAN/

  Welcome them