MySQL and PHPMYADMIN with WAMP on port 81

Similar Questions

• FirePOWER 8130 come with built-in ports and is need of a Management Center?

  Hello

  I'm looking for information for a 8130 HA pair.

  They come with built-in ports or the ports must be ordered in the form of Modules of network?

  Also a management centre needed to handle a 8130 HA pair or not?

  Is FS-VMW-SW-K9 to manage?

  Hello

  You must netmods with the device, which can be ordered with the machine.

  http://www.Cisco.com/c/en/us/products/collateral/security/firepower-8000...

  All modules of firepower including the 8000 series requires center (FMC) of management firepower

  Virtual CMF is good enough to manage it. Material FMC is normally made when there is a lot of sensors and rating that must be stored.

  Rate if helps.

  Yogesh

• Compare Dot1Q and QinQ with access ports and trunk?

  Hi all

  How do you compare Dot1Q and QinQ with access ports and trunk?

  Thank you

  Sunil Kumar

  Hey, Sunil,.

  With regard to your questions:

  1. we have a case of Dot1Q configured on the port of access of habit?  If not, then why? - Dot1q aims to tag executives leaving the switch and access is opposite, it does not therefore not used together marking.

  2. how the topology would be for QinQ case? - For QinQ as I mentioned in my last post one side will be set to while links to access than others. A simple example is explained on this link:http://networklessons.com/switching/802-1q-tunneling-q-q-configuration-example/

  HTH.

  Kind regards

  RS.

• Tablet HP 8 G2 1411: Problems with my USB port on my Tablet

  Problems with my USB port on the Tablet connector. Fees sometimes and sometimes not.

  Hello and welcome to the HP support community!

  Micro USB ports tend to be quite fragile.  A good accidental yank on the cord that connected while can be enough to cause damage.

  If you want to organize repairs, contact HP directly.

  To contact HP directly, click on this link: http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1
  
  Outside the U.S.: http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
  
  WyreNut

• My Thunderbolt screen has only 1 thunderbolt port, how can I Garland with 1 single port?

  My Thunderbolt screen has only 1 thunderbolt port, how can I Garland with 1 single port?

  It has two ports Thunderbolt.  One is connected to the cable, the other is on the back of the screen.  If you can't find the Thunderbolt port, you will have the Mini DisplayPort in the screen version.  It has three USB ports on the back.  The Thunderbolt display has three USB ports, a FireWire port, an Ethernet port, and a Thunderbolt port on the back.

  (The Mini DisplayPort version cannot be connected in a string.)

• Satellite M30: Cannot use COM with the Modem port

  Hello

  I have a satellite m30. I have problems with the com port to use with the modem. I get an error code saying 12 resources etc. There is no i/o or IRQ conflict IRQ 04 and e/s beach is 03F8 - 03FF. I tried to uninstall various things to free resources, but still the same error.

  Any help would be greatly appreciated.

  This problem when you use the Toshiba Recovery CD?
  Try to disconnect all the external devices and install Windows from the Toshiba restore CD.

  Additional please check several comments here in the forum area Modem. I found several threads with similar issues

• NB200 running Windows XP - what is wrong with my USB ports?

  I recently bought a new NB200 and have had a problem with my USB ports since then.
  Regardless, the two ports of HHR work fine with my Logitech wireless mouse - unless I have fixed via a USB hub. When I use the second port to connect any other device - in this case an external DVD - RW - the mouse just freezes. Meanwhile, the DVD - RW himself is recognized by Device Manager, etc - ('output work well - with plenty of power available per port), but it is nevertheless unable to work and Windows Explorer is unable to read any disc inserted in it.
  In addition, the USB port on the lhs is pure decoration only; nothing that I relate to it (even the mouse) won't work, neither will the capacity load & sleep (at one of the 4 Modes).
  I uninstalled the USB controllers and the ports using the Device Manager which, after re-booting, continues to report that all is well, both with the devices I attached and the ports themselves, though i's obviously not yet!
  I am concerned that I am still unable to create a recovery disk if the worst should happen if someone can help me solve my Riddle, please?
  I'm doing something wrong or, less likely to be the case, I am sure, is there maybe a problem with my machine?
  Any advice would help, please.
  Concerning
  Bob

  Try to update the BIOS to version 1.50, this solves many problems.
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  By

• By using the Tecra M11 - 11J with an Express Port Replicator II

  Currently, I have the Tecra on a cooling rack, but I think to buy an Express Port Replicator II.

  The question is: the duplicator will dissipate heat from the laptop. It would be useful in this regard?

  I would be happy to comment.

  What about John

  Hi John

  I agree with Akuma. Port replicator doesn t have the vents inside and you can't wait until the laptop temperature will be reduced because of the port replicator.
  The reasons why the port replicator is are different and, in general, has nothing to do with the computer laptop cooling.

• Individual access to the inputs and outputs on a single port (PXI-6509

  Hello

  I use PXI-6509 and this sentence taken from the Manual:

  "You can use each of the DIO lines as the input to a digital static (DI) or digital output (DO) line"

  leads me to believe that each individual DIO can be defined as input or output (even within ports), but picture:

  

  shows that these ports can be defined as inputs and outputs in the same port.

  On another card 6284 with DIO, I can put them individually.

  Can someone confirm that the 6509 is correctly?

  Best regards

  Adrian

  
  

• Mobile Mouse 4000 stopped working with USB 2.0 port, works with 3.0 port.

  I just bought the Mobile Mouse 4000, eventually find the necessary drivers, installed, but still does not work, after plugging in all my USB ports so I decided to plug in on my single USB 3.0 port, it works. Nowhere on the site, or on the box does say USB 3.0 required, I went through my device manager and all the usb ports work correctly, even, I went in the power options and turned off the selective USB power option so that they are all on. How to work with normal 2.0 because I would like to save the port 3.0 for my WD external hard drive.

  Original title: is the Mobile Mouse 4000 only USB 3.0?

  Hello

  1. What is the brand and model of your computer?

  2. are you able to work with other USB 2.0 devices normal port?

  3. what happens when you try to plug the USB key?

  4. What is the operating system installed on the computer?

  I suggest you to connect the mouse to another computer and check with the question.

  Method 1: Run the Fixit described in the article:

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2:

  As all devices have same also have USB device associated drivers. Appropriate sometimes drivers not detected after initial installation so reinstalling the drivers can fix the problems.

  You can check after uninstalling and reinstalling USB drivers if you are able to connect. You can disconnect all USB devices and then perform the following steps:

  1. click on Startand then click Control Panel.

  2. click on system and Maintenance, click System, and then click Device Manager.

  Note If Control Panel is in Classic view, double-click System, and then click Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click allow.

  3 in Device Manager, double-click to expand the "USB Bus controllers", right click on the controller host, click "Uninstall" and click "OK".

  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.

  4. Repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

  If you are still having the same problem then you can check the device USB drivers updated using windows update.

  Reference:

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  I hope this helps.

• I need to connect my HP 2200 printer for a 32-bit Windows 7 system with NO parallel port

  I have an older HP Business Jet 2200 printer coming to leave, and I love using it.  My problem is the upgrade to windows 7 and a computer-ish with NO parallel port.  I have seen cables with female parallel to USB connectors, but the cable I have has a male connector to my 2200.  I have a Dell XPS 600 former with no parallel port I want to use as a backup computer.  My system is Windows 7 32 bit.  Can someone help me? should I think about a direct stream map server thingie or I can just a cable for this?  Thank you all!

  I am VERY happy to share positive results for my project listed above.  I went on Ebay and raised his eyes to the parallel to USB cable port and found a 36 pin, which was what I needed.  I got it for next to nothing

  36 pin parallel USB IEEE 1284 Printer Adapter Cable - I got it home, plugged into the side 36 pins, the business jet HP 2200, then plugged on the side of the USB to the Dell XPS, I worked with - and immediately the cable acknowledged.  It took me a few tries to get the software and I didn't know if it was to be on the LPT or USB, so I played with both and it was released as an HPA installation, which worked like a charm!  With the fragility of the printers of today; This printer is one of the sturdies and I can still get parts for it.  He has been a workhorse for me for six years now and of course, it has been around since the beginning of the 2000s.

• BlackBerry smartphones to SYNCHRONIZE MY DELL OFFICE MS OUTLOOK 2000 CALENDAR and CONTACTS WITH MY BB 8330

  I am a personal user and not a business user.

  I loaded the disc of Blackberry Desktop Manager, and when I got my phone.

  When I connect BB to desktop UBS port, open the Desktop Manager to synchronize software... it returns an error message "no application to synchronize.  What should I do to sync MS Outlook calendar and Contacts with my Blackberry.  Funny, is that I get my emails wireless made for me in my mailbox from comcast.  I spent hours trying to figure this out. Can it be done? Thanks to all those who can help you.

  L

  Hi Laurie,

  I did a search just now and I have a thread for you to try. I can't wait to go back, but your situation was resolved by installing a different (older) version of the Blackberry Desktop software. I have Outlook 2003 and XPpro so I know it works.

  Read this and see if it makes sense. I can help you with it if you wish.

  Let me know.

  http://supportforums.BlackBerry.com/Rim/Board/message?board.ID=8300&message.ID=4026&query.ID=1886#M4...

• 3 laptops different ALL been facing intermittent problems with the USB ports.

  We have 3 laptops at home, running 3 different versions of winsows 7... Home, Professional and Ultimate. They have in recent months ALL given intermittent problems with the USB ports. A device that worked on a port stops working. It may or may not work on another port. A week later it could very well lead again on the port that wouldn't work. This applies to all types of devices.

  A few more questions:

  Is there a USB device that you use with all three computers?

  This problem occurs with all kinds of USB devices?

  The is the problem with all the USB ports on each laptop?

  Have you tried to reinstall the USB drivers? As in, uninstall via the Device Manager, restart your PC and allowing Windows to reinstall?

• I'm trying to connect two monitors and one using the hdmi port and the other vga. How can I get the pc to recognize the two?

  Original title: multiple monitors

  I'm trying to connect two monitors and one using the hdmi port and the other vga. How can I get the pc to recognize the two?

  Hi David,

  Thanks for posting your query on the Microsoft Community.

  I suggest you refer to the Microsoft Help Articles below and try the steps mentioned.

  Check out the link:

  http://Windows.Microsoft.com/en-in/Windows-8/how-connect-multiple-monitors#1TC=T1

  You can also check:

  http://Windows.Microsoft.com/en-in/Windows-8/get-best-display-monitor

  Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.

• Cannot send/receive at full speed with Intel dual port 10 GIG 82599 ethernet in guest on ESXi 5.5 OS

  Me to consider whether or not it is possible to send/receive to 20 Gbps throughput with Intel 82599 dual port card within a guest VM on ESXi. I use to send and receive traffic PF_RING DNA of ntop. I have configured the dual-port card Direct IO mode to allow the guest VM have a direct access to the card. For the traffic generator, I use a metal machine naked with another dual port ethernet to generate traffic. The generator of nu metal machine and ESXi have their double ethernet port directly connected via SPF + cables.

  In the first experiment, the traffic generator generates 10 Gbps of traffic on port 1. The guest VM is able to capture packets at full speed without any loss of package even for 64 byte packets, which translates into 14mil PPS. I had then invited VM pass to 10 Gbps for the traffic generator, which currently receives. However, guest VM was able to generate about 7 Gbps of traffic regardless of package size. The CPU seems to be fine at around only 20% of load. I do not understand why the VM can receive at full speed but could not pass to the line rate.

  In the second experiment, the traffic generator generates 20 Gbps of traffic on ports 2. The guest VM unfortunately can only capture at the rate of 5 to 6 Gbps per port for a total of 10-12 Gbit / s. I have the receiving process listens on each port on a different processor. Then, I got VM generate 10 Gbit/s on each port. Unfortunately, could not reach 5 to 6 Gbps per port, regardless of package size.

  The naked metal machine is only an AMD 2.2 ghz machine low range to four hearts. It can send full line ate 10 Gbps for gpbs port 1 and 20 for 2 ports. The ESXi server is actually a much beefier machine with the quad core Intel Xeon 3.2 Ghz. There is a lot of memory and CPU on ESXi machine.

  5.5 runs the ESXi server. I have 1 comments running virtual machine running experience.

  I'm quite puzzled why there is no bottleneck even in Direct IO mode. Both CPU memory seem to be good. I wonder if there is any setting that I need to be playing with in ESXi. I appreciate all help. Thanks in advance.

  It turned out that I placed the network card in the pci slot 3 which is only x 4 routing. I moved it to 1 (x 8) slot. Now, I get full 20 GIG.