Network connection problem Wifi (Ralink RT5390R...) and Ethernet LAN (Realtek PCIe...)

Similar Questions

• Some virtual machines have intermittent network connectivity problems and rest work correctly.

  Some virtual machines have intermittent network connectivity problems and rest work correctly. The VMs are in the same group of port and on a 4-node cluster. Physical network interface cards are appearing in vsphere client

  Please confirm if the issue has been resolved after you complete the steps.

• Wireless network connection problem

  Nice day

  I have a wireless network connection problem and I ask for help to resolve.
  What surprises me that this problem appeared suddenly, I used to connect to the WIFI correctly but two days ago my laptop could not connect to the WIFI and more.

  Other devices and computers connect with success so I think that the problem in my laptop.
  I don't have any changes on my laptop or windows, antivirus, drivers... updates or installed new software.
  Troubleshooting of Windows detected 'router or access point issues '.
  -Reset the router does not resolve the problem
  -Network adapter is enabled.
  -State of wireless card "working properly" and "update".

  I read a solution on this site, which was to change the properties of the wireless adapter, but the changes mentioned does not appear in the pilot of my laptop...

  * My laptop info. :
  DELL INSPIRON 3521
  Windows 7-64 bit
  Dell WIreless 1703 802.11b/g/n(5.2GHz)

  Sorry for this long to make, I appreciated all the help.
  Thanks in advance.

  Hello

  Have you tried to reset your laptop to a time before this issue started with a Windows 7 Restore Point?  If it is a parameter change or software this restore point can help solve what is at the origin of the problem.

  I'd also, of course, when you are resetting the router, to make sure that you let it sit for at least 30 seconds to a minute before plugging power back in.  You may need to do a few times to clear his memory to be able to connect.

  In addition, have updated the drivers for the wireless card?  What version of driver currently installed in the system?  You can consult our support site, enter your serial number and click on drivers & Downloads to find the driver for your wireless card.

  Finally, have you tried to empty the wireless profiles that are currently stored in your system?   If you delete the profile current wireless (which is to control your connection to the router), reboot your system, and try to reconnect Windows will rebuild the profile and hopefully allow you to log in again.

  I would like to know if any of this helps.  To help resolve this more effectively please click on my user name Dell Todd and send me a private message with the Number of Dell Service from your system.  Please keep all troubleshooting and discussions on this thread open so that others can find the information they need to solve their problems.

  Todd

• Network connection problems, forcing APIPA to be always active

  Original title: APIPA
  According to the manual of microsoft
  IPAutoconfigEnabled = 0
  is defined in each group of interface parameters in the registry
  but ipconfig/all says:
  Automatic configuration: Yes
  and tcpip sometimes gets the 169.254.x.x address
  The DHCP service stops
  Network driver has been reset, reinstalled, updated...
  Automatic configuration (APIPA) is still on
  How to solve this problem?
  (Vista x 64)

  Hello

  
  1. is this a wired or wireless?
  2. don't you make changes on the computer before the show?
  3. What is the accurate and complete error message that appears on the computer?
  
  Method 1:
  You can perform network troubleshooting steps from the link:
  Network connection problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems
  Also, try the steps from the link:
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
  
  Method 2:
  You can also reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself:
  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357
  
  Method 3:
  You can try to release and renew the address IP address and check if that helps. To release and renew your IP address follow these steps:
  a. open windows command prompt
  b. click Start - run type cmd and press enter
  c. to release your ip address ipconfig/release , press Enter
  d. to renew your ipconfig/renew IP address
  
  Method 4:
  You can also consult the knowledge base article and check if it helps:
  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233
  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base. How to back up and restore the registry in Windows:
  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

• Home wireless network connection problems

  What should I do if I normally connect to the wireless network does not appear?  It is not a network card problem, because I can connect to other wireless and school and other places.  I tried to reset the router, ping and by unplugging and seeing what I could understand on the computer at home, but nothing does.  Any ideas or suggestions would be greatly appreciated.

  Thank you.

  Hello

  Have you tried other computers to connect to your router? You use both wire and wireless
  connection?

  Unplug the modem and Router 3 + minutes. And then reconnect the modem - when it is running
  Plug in the router - when it is running - restart the computer. This is known as a hard reset.

  Check with your router manufacturer support.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

• Failure of the motorway E - there are network connectivity problems or this peer has different support encryption (AES / non - AES software)

  I have two websites and a cluster CPU as below:

  site - 1

  CUCM pub-1

  Pub 1 CUC

  imppub

  exp-c-1

  exp-e-1

  site-2

  cucm2

  CuC2

  IMP2

  exp-c-2

  exp-e-2

  !

  I do a bunch of highway E and C, but it I show error on cluster of highway E:

  Failure - there are network connectivity problems, or this peer has the support of different encryption (AES / non - AES software)

  This highway is part of a cluster, but is not the master of the configuration. Configuration changes made on this highway may be lost. More information about the Clustering help page.

  !

  What is the solution to fix it?

  Locally add cluster of highway or having to make cluster of 4 motorway between locations?

  How far are the peers of the highway on the other, what is the round trip time?  This should be within 30ms.

  Can you confirm that all highways in the cluster have the same keys option installed on all peers, as it is a requirement, call license quantities can be different, but the features option enable/disable keys must be the same.  Additionally, make sure that the version of the software installed is the same, that you have a version mismatch or could be active where encryption the other not.

  Regarding the "this highway is part of a cluster, but is not the master of the configuration... '. "this message is normal for a node that is not the master, as it is said just only make changes on the master, since all changes on the slave will be replaced by the master.

  Suggest you watch on creation of Cluster Expressway and maintenance Deployment Guide (X8.8) in case you have not yet.

• Wireless network connection problems

  I have problems to stay connected to my wireless router.  There are 3 laptops and 2 workstations connected, but my laptop does not seem to disconnect every time my computer sleeps or is closed.  I have to go through this process to solve the problem in which the connection is immediately restored, but then disconnected and connected once again. I tried to remove the connection & restores and troubleshooting with the router, but nothing seems to solve the problem. Other computers never have this problem.  My laptop is fairly new, and I'm quite puzzled as to why he's in trouble.

  Hello

  To provide the proper resolution, I would need more information on your side.

  What is the number and the model of the laptop?

  Windows can be disable your network adapter to save power. You can try to disable the power saving option in the network adapter properties

  I suggest you try the steps to disable power saving option. Check if it helps.

  a. open network connections by clicking the Start button, and then clicking Control Panel.

  (b) in the Search box, type adapterand then, under network and sharing Center, click on view network connections.

  c. right-click on the connection and then click Properties. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  d. click the Networking taband then click on configures.

  e. click on the power management , clear the checkbox allow the computer to turn off this device to save power tab and then click on OK.

  See the article for more information.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• Network connectivity problem, it must be disconnected at random

  Original title: connectivity problem

  connectivity problem: under troubleshooting is said: problem with nearby connections... the computer disconnects Internet after 45-60 minutes - it closes down also, usually when I repair as administrator, I can connect to internet, but still a time when left almost an hour without using the internet disconnects?

  Hi Kvhan,

  1. are you using cable or wireless network?

  2 have you made changes on the computer before this problem?

  This problem can occur because of network settings, try the following methods and check if it helps.

  Method 1:

  Run the network troubleshooter utility.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2:

  This problem can occur if authentication enable IEEE 802. 1 X for this network checkbox is enabled. If this box is checked, but there is no server to authenticate the connection is interrupted. If you turn on the wireless network connection, it disconnects again after a short period.

  To disable authentication IEEE 802. 1 X, follow these steps:

  a. Click Start, type ncpa.cpl, and then press ENTER.

  b. right click on your wireless network connection, then click Properties.

  c. click the wireless networks tab.

  d. under preferred networks, click your wireless network, and then click Properties.

  e. click on the Authentication tab, click to clear the authentication enable IEEE 802. 1 X for this network check box and then click OK twice.

  Reference:

  Problems in Windows wireless and wired network connection: http://windows.microsoft.com/en-US/windows/help/wired-and-wireless-network-connection-problems-in-windows

• With device log Insight network connectivity problem

  We manage the virtual appliance 1.0 - beta and I noticed that the virtual appliance will fall the network periodically for a short period. I had constant pings, it will and it will just stop respond for anywhere from a few seconds to several minutes. You can also see in the capture where the data is missing in the user interface of screen attached. I know that we are not the problems with our ESXi hosts or dvSwitch because there are many other virtual machines running on the same host ESXi and same VLAN and they are not network connectivity problems. Does anyone else know this?

  Sounds like a network problem. Perhaps you have a dual IP / MAC address on the network? Do you perhaps have a routing problem on the network log Insight's sitting on that?

  Can you generate a bundle of support and download the instructions here: http://kb.vmware.com/kb/100852 (no need to SR just create a file called mvanbeck)

• EBS R12.1 network connection problem

  Hi hussein.
  
  We have the new location of the EBS R12.1.1 in a client with a security network "tight."
  
  My problem is that in a certain Department with the network 192.168.1.xxx segment than the connection of the EBS is fast, while
  the Department with a segment of network 192.168.2.xxx EBS connection is very slow, that has been a very long web pages
  to open it. I can really conclude the customer that it is their network problem. They want to prove that it is.
  
  How to do a basic test for network connectivity? Is the server from the client PC enough EBS 'ping '? We can
  

  C:\Documents and Settings\Administrator>ping 192.168.1.107
  
  Pinging 192.168.1.107 with 32 bytes of data:
  
  Reply from 192.168.1.107: bytes=32 time<1ms TTL=128
  Reply from 192.168.1.107: bytes=32 time<1ms TTL=128
  Reply from 192.168.1.107: bytes=32 time<1ms TTL=128
  Reply from 192.168.1.107: bytes=32 time<1ms TTL=128
  
  Ping statistics for 192.168.1.107:
      Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
  Approximate round trip times in milli-seconds:
      Minimum = 0ms, Maximum = 0ms, Average = 0ms

  The statistics above may give clues to a network connection problem?
  
  
  
  Thank you very much
  
  
  Mrs. Mina

  I guess that's the same thing with R12.1.1?

  -Yes, you can also refer to:

  Compare the needs in bandwidth between the version 11i and 12
  http://blogs.Oracle.com/stevenChan/2007/06/comparing_bandwidth_requiremen.html

  Thank you
  Hussein

• There was a problem with the Windows Live Hotmail service (a network connectivity problem temporary has nothing to do with your computer).

  There was a problem with the Hotmail service (a network connectivity problem temporary has nothing to do with your computer). Please try again

  . I really need to fix this! Help!
  original title: no answer not before!

  track every step!

  no change!

  I am getting really worried about it!

  Please ask in the forum Hotmail. We do not use it. We cannot answer your question.

  Windows Live Solution Center Hotmail Forum
  http://windowslivehelp.com/forums.aspx?ProductID=1

• Windows 8 pro and windows 8.1 pro 64 bit drivers ralink rt3290 and lan realtek PCIe FE Family Controller

  Hello

  I have a HP Pavilion GP A10 AMD laptop 2313-AX. The latest drivers from the HP website for windows 8 pro and windows 8.1 pro 64-bit drivers ralink rt3290 and lan realtek PCIe FE Family Controller appear limited in my laptop, but in the same laptop connectivity when I start in Windows Server 2008 R2, both LAN and wifi works very well.

  Are there drivers available updated 2013 for these two hardware devices as dated?

  Are there universal or generic drivers that can act as a workaround?

  If so, please give me the URL for the same thing.

  Kind regards
  Sriram.

  Hi Steve,.

  I came across similar issues where the driver manually enabled users to solve the problem. Uninstall the current network adapter drivers and manually install drivers that you previously downloaded.

  a. press Windows key + R key, type devmgmt.msc, hit the Enter key to open the Device Manager.

  b. expand network adapters, right-click on the listed network adapter and select Update driver software.

  c. click Browse my computer for driver software, click Let me pick from a list of drivers for devices on my computerand then click on disk.

  d. in the dialog box to install from the disc, click Browse, locate the drivers, and then click Open.

  e. follow the steps described in the DeviceName update driver software dialog box to update the driver.

  Try these steps and let us know the results.

• Photon: Dropped calls and network connectivity problems

  I bought my Photon August 18 and he was not long for me first to the problems with network connectivity.

  The phone displays signal on the phone, but when you try to call, send text messages or surf the web. Zilch.

  A soft reset works every time. I've had some experience with the issue of the "appeal of ghosts", but had no network connectivity so often that he was too much a problem. Restores the soft 3-4 per day.

  I took the phone to the Sprint store and they told me that my phone verified and were not hardware problems that may be found. I said at the time on the update of the software of MR5 and was anxious to see how the phone after the update.

  I received the update on Wednesday and the phone worked fine. No appeal of ghost, no network connectivity not problems, only dropped the call.

  Now, Friday morning, I lost network connectivity despite seeing the strength of the signal and had to perform a soft reset to regain connectivity. My wife and I bought this phone at the same time. She had many calls interrupted before the update and we both experienced after that update eventhough signal showing on the phone is at least two if not more bars.

  Is this a known issue? Is it going to be/CAN this be corrected by a software update? Is this phone a lemon and he'll remember?

  I LOVE this phone. I don't want to get rid of it, but...

  Seriously. It's a phone! Making calls should be the FIRST thing that is done right.

  Please, someone, Motorola, reassure me that this isn't a lemon and that network problems are going to be fixed. I CAN wait, but I don't want to get stuck with two phones for $200 that need to be pampered just to be usable.

  Thank you

  TC

  Yes, it turns out that be was a buggy phone. Two stores tested Sprint phone for reception of the signal and they said that it spent; but as said the technician in the second store, the tests they take place the phone in ideal conditions.

  The two stores I've visited, said they were ready to replace the phone, but my first visit came just before the MR5 update software while I was willing to wait to see if the update corrects the problem. It didn't, but the replacement of the second store phone works fine with upgrading to MR5 and really no problem.

  I'll go ahead and mark this question as a response, but if you experience the same problems of chance complete loss of all network connectivity (Sprint or otherwise), I recommend getting the phone replaced. It is a bad camera.

  Oh and the technician at the second store mentioned the network problems. It has been a problem for them, but the most telling proof of the issue of network is random dropped calls. So if from time to time, you lose a call under the conditions of good network signal, it's probably not your phone and Sprint. I have almost that many abandoned calls as of late, so it could have been the wrong phone I had that really amplified the problem... or... Sprint has got some of the bugs in our region.

  Thank you for looking in. I hope that your problems are as easy to solve as mine and I hope that you are still within your 30 days so that you get a new replacement.

  Best wishes

  TC

• Problems connecting an Officejet 7310, wireless and ethernet cable

  My printer (Officejet 7310) is connected to two PCs with an ethernet cable and the router. Now I want to install a laptop as well.

  I know that the lap top is communicating with the wireless router, but I can't get the laptop to recognize that there is a printer is installed.

  I tried to connect the printer directly (via Ethernet cable) to the laptop and it works fine. I downloaded the latest version of the software for the 7310 and used two options (without wire and cable).

  Any help would be most appreciated.

  Cutting the anti-virus made no difference.

  I HEALED NOW THE PROBLEM!

  Installed a new router 2wire.

  Thanks a lot for your help.

• BluRay BDPS3100 network connection problem and cannot remember the last position a DVD was finally play

  Third time, it will not make a network connection. Last two times, I called Sony about the probplem of Youtube, it turns out that it was a Sony problem and a week later, I did a udate software and it fixed the problem. Now for the third time, the device does not connect. Check all the settings and looks good. ??????

  And finally, the unit does not remember where the last stop on a DVD has been in the Middle film.

  Seems that it was poorly designed. I got my 5 years old and it worked perfectly.

  Maybe time to consider other products. Any suggestions?

  Someone has something they want to add?

  To the problem of internet connection, perform a power reset on the player and the router.

  1 turn off the player and the router, and then unplug the power cord for 1 minute.
  2. after one minute, plug the player and router and then turn on again them.

  You help us, please provide more information. How you connect the player to the internet, wired or wireless? Do you receive an error message? If Yes, please provide the exact error.

  For the movie problem, you say you cannot resume the film if you press stop or pause?