Network wireless Ethernet networking device

Similar Questions

• 'Wireless network device has been disabled' - Satallite A300

  My mother bought this yesterday and shes already been buried under problems, the transfer cable has absolutely nothing of his portable od (although I think that this is the problem, not a new) and when trieing to connect wireless to our network, a message appears "the wireless network device is disabled. Please turn on the camera. "appears...

  ADAPT bit at the front is now in a position to market... and the lght wireless is also on... ive tried Fn F8 also and nothing happens... Although in the essay the Fn brightness key does not change so I think that maybe there is a problem there too although im not familiar with vista.

  With the wireless, he has not yet received up to even looking for a network connection... and connects fine via ethernet... cable please help me with connection problems and a side note advice with other problems.

  Not sure of the computer laptop cos he got just spilled on my knees with a "fix it": p

  Hello

  I put t know what that card WLan you have but you should try to reinstall the WLan driver.
  Go to Device Manager and check first your WLan card.
  Then download the page of European Toshiba driver WLan driver.
  Then delete or uninstall the old drivers WLan (Device Manager) and install the new downloaded drivers.

  Reboot the laptop, and then enable the wireless using the antenna WLan switch and the combination FN + F8.

  If you are not familiar with Vista and don t know how to use the Wlan under Vista OS and then google and you will find many pages that describes how to set up WiFi network.

  Check it out!

• Photosmart HP 7520: All wireless network devices will lose connectivity after printing

  Dear all, 
  
      I have a problem with my HP Photosmart 7520 printer where all wireless network devices will lose connectivity after a printer has been sent to the printer.
  
  * Summary
  Wireless network unusable after sending one print to HP printer
  No device ( computers nor smartphones ) can use the Internet nor access internal networks ( 192.168.0/24)
  
  * Details
  Turn HP printer on.  ( wireless direct is off - never turned on )
  HP printer connects to working wireless network.
  Other devices ( phone/computers ) already connected and working.
  From any device, send a document to the printer.
  Printer prints document successfully.
  Immediately after printer has printed all devices cannot access internet IP range ( including HP printer ) nor Internet nor router ( 198.168.0.1 ).
  
  * Reproducibility
  Always
  
  * Work around
  Disconnect all devices from the network.
  Power off printer.
  Reboot Internet router.
  
  * Attempted solutions
  Removed wireless configuration.
  Factory reset.
  Added wireless configuration back.
  Powered on and off printer.
  
  * Printing tested with
  Tested with Macbook10.11/Windows 8/Ubuntu 12/Android 4.4.2
  
  * Not tested
  Ethernet cable directly connected to router.
  
  * Internet Router
  Netgear CG 3700
  

  Number of brand and model of the router?

  These settings are to set up your printer wireless (or wired):

  • Stay connected to your router
  • Trouble printer status 'offline '.
  • Wake mode 'sleep'
  • All wireless devices stay better connected

  While the DHCP is convenient, devices like printers (wired and wireless) should always be assigned a (fixed) IP address manually to avoid conflicts on your wireless network and must be outside the range of the router DHCP.  After the adjustment of the static IP address the computer must be updated to show a Standard TCP/IP port with the IP address of printers under printer properties/Ports.

  1. Set a static in the printer IP address (click here) outside the range of the DHCP of the router (check your manual). It is for Linksys routers, but can be used for all routers. Check your DHCP range and change this first if necessary. More Help Wireless Printing is here and here and still more here.  Video here explains the problem and how to solve the problem. <--> So watch this!
  2. Or check in the printer "Auto Off/sleep/Energy Saving Mode" is disabled the System Mode Time Out is set to zero (0) Use the built-in webserver (EWS) by visiting the printer address IP address in the address bar of your browser, click on settings tab/Auto Off. Or use the printer, printer Home Page (EWS) Wizard. Also check your printer properties.
  3. If the printer supports and has IPv6 enabled, disable the IPv6 option in the printer.
  4. Make sure that the printer is connected directly to a socket wall and not to a UPS, power strip or a lightning arrestor. This will cause the printer to drop offline connection and disconnection (checked yes!).

  Additional measures to take if you continue to have the problem (if they are posted)...

• wireless network device no 104 during the replacement of Intel 3945agb with Intel N 1030

  When replacing the wireless Intel 3945agb with Intel N 1030, the message card "wireless network device 104 undetected." system stopped. remove device and restart" appears.

  Intel ensures that these 2 cards are compatible.

  Model: DV-6600 series (DV-6660eb), built in 2007.

  Vista Premium (32 bit)

  No change on HW and SW since it was purchased

  BIOS: F5A (latest version according to HP, 2010).

  How to activate the wireless card Intel? (Download the BIOS of recent products with N 1030, such as DV6-6xxx 1xxx G6,...) ?

  Thank you

  solved flashing BIOS with whitelist F.5A deleted:

  http://www.BIOS-mods.com/forum/thread-HP-disabled-whitelist-mega-thread?page=15

• E/s network device Usermode and ConfigFree protocol error

  I have a Toshiba laptop and recently it has not started properly, displaying the following message: "Not found TOSHIBA Network Device Usermode i/o Protocol. Please reinstall ConfigFree. OK ".

  I'm unable to use the laptop and it will not close without having (although once it has stopped and rebooted OK and then worked fine for three days we have left it for Christmas and now it does once again). Can someone let me know what does this error message mean and how do I deal with it (I know little about the functioning of my laptop!).

  We have Windows XP and are configured for a wireless broadband connection. I'd be wonderfully happy if I could work out what I was forced to move to work rather than working at home today because of this!

  Thank you in advance!

  Hello

  The message is clear.

  > Please reinstall ConfigFree.

  Then why didn t you reinstall this utility?
  If you didn t create the utility CD & Tools you can download this utility from the Toshiba driver page.
  Then remove the ConfigFree to add & remove programs, reboot the device and reinstall the ConfigFree.

• Airport not showing is not as network device?

  My Airport Extreme 802.11ac does not appear in the finder as a network device. It showed in the previous Extreme model I was using, then leave for any reason any. After messing around for a month or two, then trying to get it working again, I bought the new 802.11ac AE, but it does the same thing.

  I have two other devices that appear in the finder under the shared part of the side bar of the Finder window, but cannot figure out how to show by EI. The wireless feature works very well, as a printer BSE connected to the USB port of the AE. Internet

  It would be different if I was using the IP address of the type 10.x.x.x instead being in bridge mode and using 192.168.1.X?

  Any suggestion is appreciated.

  My Airport Extreme 802.11ac does not appear in the finder as a network device

  In the finder it will show only upward if you have a connected USB drive.

  It showed in the previous extreme model that I used

  Only if you have the network resources available to him.

  Computers will be displayed, because they offer resources network, the PF to be exact.

  But the airport will not be displayed. Mine is not, and never has.

  My Time Capsule arises because it is a hard drive offering services of files on the network.

  Printers will not appear in the finder no longer...  Again, I have printers online... they do not show in finder and never have any version of Mac OS X, I used.

  However a printer with USB or SD card slots and a wired card which offers services of files on the network may appear... In the only finder services files will be displayed.

  EI has to offer network file services appears in the Finder... Plug a USB stick into the USB port and set it to share on the network and the AE will then appear in the finder.

  The place that you are looking for your AE's utilitarian Airport... It's the Apple of method available to see you the configuration of EI... no viewfinder.

• Networking the cDAQ-9188 - no 'network devices' Max

  Hi all:

  I have problems connecting my NI 9188 cDAQ via ethernet to my computer. MAX does not display it in his repertoire, or it displays "network devices". Based on the guide NOR offer, I don't know what else to do (I can't access the modules in a LabVIEW project which is my problem).

  I used the tool online browser that seems to be the equivalent of MAX and works very well - I can see the IP address of the controller and it shows what chassis slots are used by what the map.

  I tried manually inputing this IP in a remote system to the MAX, but that hasn't worked.

  Any ideas on how I can networks controller on my computer so I can actually use in a LabVIEW project.

  I have LabVIEW 2012 32 Bit. Would a student version be the cause of the problem?

  Thank you very much.

  cuaerospace wrote:

  I am familiar with the method you describe, but I agree with all the power cycling to get some of these products to work. I had to do this several times with the cRIO. Any chance you could give a little more than a description step by step explcit of your approach? Thank you!

  Good so here's what I did to try to reproduce and to have a step by step of what I had to do.

  Firstly I have reset my cDAQ so that it would be if all goes well in the mode that yours is.  To do this, I pressed the button to reset for 5 seconds then.  I have also all my network devices defined to "Obtain an IP address automatically" in the IPv4 settings in my network connections.

  After that, I start MAX.

  Go to devices and Interfaces > network devices, then I right click and choose Find devices.  It took a lot of time and the list was empty, but then I noticed that while he was always looking in this window, the MAX window showed my cDAQ-9188, who was a white device.  There, he registered the IP address as 169.254.93.149.  At this point if I went to the device to the MAX I saw where he sometimes States under network settings that no network adapters found.

  So I closed MAX and open my "view network connections" in Windows, I just searched that term in the start menu.  Then for my device properties, went to the IPv4 properties, set the IP address of 169.254.93.0 with 255.255.0.0 default gateway.  It is, so I'm on the same subnet as the appliance.

  I then restarted MAX now when I go to the device under devices, network and network settings I can set static IP and subnet is 255.255.0.0 10.10.10.100 then save.  Then closed MAX.

  Then I went back to my view network connections, the static value of what I really wanted is 10.10.10.0

  MAX then launched.  Find my device that is always white, click Add the device.  And then all is good.  I don't know if all these steps are necessary, and I don't know if there is an easier way, but it worked for me.

• wirelles not conect, problem of network device

  Network device, control device, wirelles conection problem

  Hello

  1 are there any changes or updates made on the computer before the show?

  2. what operating system is installed on the computer?

  3. What is the full and exact error message?

  I suggest you to return the item and check if it helps:

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  In Windows network connection issues

  http://support.Microsoft.com/kb/313242

  If the problem is not resolved, please provide more information to help you best.

• all Parental control computers appear as 'Network Device'

  Hello, I have a Verizon FIOS router that I believe must remain as a router and I have bad wireless coverage in my house. Various articles mentioned that a wireless router can be configured as an access point by turning off the DHCP / NAT and cascade the new router (E4200) in the local network (without using the WAN port). This seems to work very well for the first device, which I have added to the wireless network, but when I went to set up parental controls to restrict access, all devices in the selection box appear as 'Network Device', so you can easily know which devices choose. Is it the way things are if you do not use the software or are - because I use it in a non-standard way? Does anyone know how to have that came with the computer names?

  Thank you

  Al

  Parental control is relevant only if the router is used as a router as access point. You may not use the parental controls on the E4200 if you use it as an access point only.

• HP Officejet scan cannot be run, error "Scan cannot be performed because another program or computer uses the network device.

  Hello everyone,

  After you have installed Windows 8 on my desk, I lost the ability to scan with HP (Officejet 8500 pro wireless) solutions Center. Wen I click on scan (rather photo or document) I get a message: "Scan cannot be performed because another program or computer uses the network device. There is a little information on the HP site. I've tried all the suggested solutions, including several install and reinstall the HP software. The printing part works very well, and I can scan with other programs directly using the WIA driver. Now I scan documents to pdf authorizing searches, who wants me that this question be set quite often. Currently, I use my laptop for that. Everything works very well with Windows 7.

  Any help would be appreciated.

  Thanks, Johann

  I contacted HP about this specific problem.  They informed me that it is an upgrade of Windows 8 that Twain issue and they do not support this problem.  Reinstall the current drivers of hp does not help.

• Watch is not in the wired network device manager or manage networks

  You have a slgiht problem, I have a HP DV6, do not ask me which model and I noticed when I tried to connect a PS3 to the laptop to share the internet the wired network adapter was not appear anywhere. I checked in internet Manager network cards, network devices, and it's not listed, I then checked the program uninstaller and found that the driver was listed for ethernet so decided to uninstall and reinstall but nothing. I then went back and plugged in an ethernet cable from the router to the laptop and it appeared, why is this and y at - it a way to get the wired connection to show at all hours because it means that I can share my internet connection for laptops with another device.

  Hello:

  It's probably a setting in your BIOS to disable the power saving Mode LAN (which by default is set to enabled). Normally found in the system configuration menu.

  When your laptop is on battery and you plug in a network cable, it may not work if the LAN Power Save mode is set to enabled.

  Disabling the setting allows the map LAN is present and ready at any time. Press the F10 key there and at the exit of the BIOS to save settings and exit.

  Paul

• (Redirected) For Dell Dimension 5150 Windows 10 upgrade: "there are no supported network devices.

  Hello world

  I have run the applet get Windows 10 and get the message: "there are no supported network devices.

  I use the router directly from the ethernet port, so it seems that the Dell 5150 driver for this is not Windows compatible 10, which is disappointing.

  Does anyone have a solution to this, or I'll have to just buying another cheap network card?

  Thanks in advance,

  J McVirgo.

  Best of this post in the forum Windows 10 here:

  http://en.community.Dell.com/support-forums/software-OS/f/4997

  Bev.

• Setup could not find any supported network devices

  Hi all -

  I try to install ESX 3.5 on Windows 6.5 for learning virtual machine. During installation it says "Installer could not found no supported network devices.

  My Intel Core2 WD system and the NETWORK interface is "Realtek RTL8168 (p) / 8111 PCI Gigabit Ethernet.

  Please let me know why I get this error.

  Thanks in advance... J

  Shiv

  Make sure that the virtual network adapter is connected - also if you did not check the white paper on the http://knowledge.xtravirt.com/ title VI3.5 in a box - provides detailed instructions on how to set VI 3.5 under my computer.

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• MacOS Sierra - time machine stuck preparation backup on network devices

  Since I've upgraded to Mac OS Sierra, cannot use my local backup USB. Time Machine is stuck with the message "preparing backup" - more than 12 hours - for network devices, an Apple FileVault and another NAS device. Works very well with the local USB drive.

  Something funny underway with network devices such that she works for the drives the.

  Hope Apple take note and fix.

  I have the same problem. I found this,

  macOS, problems of the Sierra: Time Machine backup Mac

  Time Machine problems prevented the Mac owners of their devices to backup since the upgrade to Mac OS Sierra, and the problem is widespread enough that Apple has published a guide on what to do if you can't back up:

  Discount for the iMac SMC

  1. turn off the device

  2. unplug the power cord from the monitor

  3. wait 60 seconds

  4 reconnect the power cord

  5. DON'T TURN ON DEVICE

  Reset the PRAM

  1. the computer must always be switched off.

  2. Locate the following keys on the keyboard: command, Option, P, and r. you need to hold these keys down simultaneously in step 4.

  3. press and release the power button to turn on the computer.

  4. press and hold the Command-Option-P-R keys. You have to press these keys before the gray screen appears. Continue to hold the keys down until the computer is restarted, and you hear the tone of starting for the 3rd time.

  5. release the keys.

  You can then try to save again. If this does not work, try to disable indexing on the drive you want to back up.

  but I'm not sure it's the same question. I'll try it and report.

• We are trying to install FSRM (File Server Resource Manager) in windows server 2 k 3 R2 SP2. After installation, its error message that gives as no network device connected. Suggest me!

  Original title: problem in installing FSRM

  We are trying to install FSRM (File Server Resource Manager) in windows server 2 k 3 R2 SP2. After installation, open the FSRM in "All programs", its error message that gives as no network device connected.  Suggest me!

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows 7 networking forum.

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

• Listed unknown network device

  Two unknown devices appear on my player network as 'EXPTRACKINGPC '.

  "

  These network devices are automatically added as part of the Windows Media Player sharing features? The first one above is protected by password and I can't access the file. I don't like sharing media through Windows Media Player, how can I get rid of them?... .or is that a hack program that somehow got installed despite my security measures that have been taken? I can't find anything on the web dealing with these devices. Thank you

  It looks like another computer on the network.  You could probably open a command and ping the PC name to see what IP address it has.  Perhaps even then go to your router and disconnect them from your network.

  Some ISP problems (configuration errors) can also make your neighbor computers appear in your network.