Similar Questions

• Add new Member and firmware update

  Hello

  I have a group of 4 bays Equallogic

  1xPS4000 (Type: 70-0120) and

  3xPS6100 (Type: 70-0400)

  They all firmware v6.0.4

  The new table is a PS6210XV. I'm sure that the firmware of it's newer probably with a release v7.x.

  The documentation for the firmware update, it says that I have to upgrade all the tables on my group first, and then add the new group.

  I was hoping to add the new table and move some of the volumes to that one, update a table that I emptied, add back to the pool, empty one another etc etc.

  Is this possible?

  It is really not a good idea to do so.   In place upgrade is by far the best option.  If you have defined your timeout of 60 seconds and choose a period of quierter I/O, that there should be no problem.  Also, be ready for an upgrade means that be ablel to handle a failure of the controller in the case of a real problem of HW.

  First, if.  You need TO upgrade the new Member and all members of 6.0.x to 7.0.9.   The new table will come with 7.0.x since it is the minimum version for this controller.  Upgrade to 7.0.9 as well.  Create a new pool for this member and do not set the RAID policy yet.  Do not enable the iSCSI 2nd course interface.

  What disks you have in the existing tables?

  You run VMware ESXi?

• Photosmart 7520: News on the firmware updated

  Hello

  I was talking to HP support problems with the latest firmware pushed for the 7520 breach ePrint and network services and they told me that there is an updated release due to be released for download via the software / support site, I was wondering when the new firmware is supposed to be available?

  Matt

  Hello

  A new firmware to restore the ePrint feature are available on hp.com, however it is currently available for MS Windows :

  http://support.HP.com/us-en/drivers/selfservice/swdetails/HP-Photosmart-7520-e-all-in-one-printer-series/5199461/model/5199462/swItemId/OJ-113641-5

  I don't know if / when it wil become available for Mac OS, that's why I suggest you get a Windows PC and update of the printer, if you can have such an or can borrow a laptop to a member, family, etc.

  If you need to use another PC, remember to install the printer drivers first prioor runs the update:

  http://ftp.HP.com/pub/softlib/software12/COL43773/MP-108670-3/PS7520_1315-1.exe

  Kind regards

  Shlomi

• Problems with the new office of Windows Update January 14, 2014

  The update on the Windows desktop appears to have downloaded on my laptop and then request e-mail/password or a key product to allow it. When I click on the product key, a small window opens with the message get your new windows of office ready for you... it will take a few moments... and then crashes on this message, so I can't put a product key or closed Word / Powerpoint downwards. Does anyone have any suggestions on what I need to do this issue?

  Hello, Beverley,

  Thanks for the information and apologies for the late reply.

  I suggest to reset Windows update components and then check if the problem persists.

  Important this section , method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: How to back up and restore the registry in Windows

  Please reply with the results, in order to help you solve the problem.

  Thank you

• Install RAC 11 GR 2 and apply the patches with the new Option of software updates YES

  Anyone tried the installation with the new Option of software updates?
  
  I'm going to install grid RAC 11 GR 2 and I intend to do the following steps:
  (1) install the Oracle Grid Infrastructure 11.2.0.2 patch group
  (2) make all configurations with YES
  (3) create ASM disks
  (4) install Oracle Database 11.2.0.2 software only
  (5) apply recommended patches 11.2.0.2.2 Oracle (12311357) and 12431716. (Ref. MOS doc [756671.1 ID])
  (6) create the RAC (advanced option) with DBCA database
  
  With these steps:
  Grid and ASM disks would be configured without the recommended patches, but the database will be created with applied patches.
  
  I would not do a "Software only" install IM and then apply the patches because later I would have to manually do all the configuration steps.
  
  If I use the Option of YES software updates to apply patches, YES makes the adjustment, and then I would set up the GRID with YES?
  
  Quote from Oracle® Setup Guide Network Infrastructure 11 g Release 2 (11.2) for Linux - E17212 number of part-11:
  'Use the feature of dynamic download and apply software upgrades of software updates as part of the installation of the Oracle database. You can also download updates separately using the downloadUpdates option and later to apply during installation by providing the location where updates. »
  
  I could not find more detailed information on this feature in the documentation and MOS.
  
  Thank you

  Hello

  You can download the latest updates and patches to help with option - downloadUpdates

  ./runInstaller -downloadUpdates
  

  You can use this note:

  * How to download the latest updates and patches using 11.2.0.2 YES [ID 1295074.1] *.

  Don't miss...
  * Error: INS-20704 while installation 11.2.0.2 with Option 'use downloaded software updates' [1265270.1 ID] *.
  : Note ensure that the user download the updates of patches have own/correct permission to download updates to patch to MOS (My Oracle Support).
  Do not use the directories/tmp/oraInstall * for the download location. New bug 9975999

  Documentation explaining...
  4.5.1 running Oracle Universal Installer
  Download of updates before Installation
  http://download.Oracle.com/docs/CD/E11882_01/install.112/e16763/inst_task.htm#BABJGGJH

  Kind regards
  Levi Pereira

• New Firmware Update - where is the change log?

  I see that a firmware update was sent to my phone. However I can't find a change log. Where is it?

  Hello!

  HP and Microsoft has released an update (online) of the OTA for the X 3 elite on October 25, 2016. The update installs Windows Mobile 10 for the following versions:

  Firmware revision: 0002.0000.0014.0100

  Build of the OS: 10.0.14393.321

  Bootloader Version: 520101

  New features:

  Area	Description
  Display	High brightness Mode is activated when the brightness adjustment is suggested by default.
  Security	Reset functionality is enabled. However, the existing user must reflash phone with this software with Windows Device Recovery Tool (WDRT).

  The issues addressed (Items with * are fixed by OS updates):

  Area	Description
  Apps	App Instagram, have green lines during use is fixed.
  	Launch of view inconsistent HP on docking tools is fixed.
  Audio	Detection of the helmet is not reliable is fixed.
  Camera	Auto focus performance and stability in low light conditions are improved.
  	Model tapes preview screen is fixed.
  	Video recording after that tap put in pause/resume many times received message 'something went wrong' is fixed.
  Security	Blue BitLocker Recovery screen on reboot with active device encryption is fixed.
  User interface	Tap to wake up the wrong feature turn off screen is fixed.
  Hello Windows	IRIS is unblock, followed by sweeping to unlock quickly led to the prompt error is fixed.
  	Fingerprints and Iris being setup one after the other, one of them will not functional, is fixed. **

  Known issues:

  Area	Description
  Apps	Skype for business app can be run from external display of Continuum.
  Connectivity	Dock desktop LAN port of HP has no configuration of the user interface.
  User interface	Missing tiles with update settings. The user can go to the list of applications, press the settings icon and select PIN to start restoring the tile.
  	Tile 2 Messaging becomes white with update. Touch on the tile once it restores.
  Security	Too many failed unlock attempts, the device will be blocked for security reasons. User can unlock the unit to https://account.microsoft.com/devices.

  Thank you

• S2110 new firmware updated for Tablet and keyboard

  We finally got a first major update (about 160 MB) and the Tablet seems more vivid. However, no one knows exactly what has been updated?

  The mentioned update:
  (1) update Google GMS
  (2) remove Lenovo Appstore
  (3) cannot remember what it was

  The keyboard firmware update had no details on what has been updated

  Also, the questions that we have been always complain have not been set:
  (1) the words not being in the dictionary and still having red lines under can't use spell check
  (2) Tablet battery drain when connected keyboard because he won't sleep

  Continues to conduct tests to determine if the problem to delve into the keyboard and it does not work is now completely resolved.

  However, someone has more information on this update?

  The update of the firmware seemed to solve the problem of the dock being not recognized periodically. So that's very good!
  Also, no new WiFi issues for me.
  The bummer is that this update does not resolve the question of dictionary/spelling. Every word I type in gmail is always highlighted as misspelled!

• I have updated Dreamweaver for 2014 and this toolbar disappeared.  I have a new installation of 2014 on another computer and the toolbar is there.

  I have updated Dreamweaver for 2014 and this toolbar has disappeared.

  

  I have a new installation of 2014 on another computer and the toolbar is there.

  Anyone know how to get it back?

  I'll make sure "Enable related files" is checked:

  

  Otherwise, click on apply once checked and then restart Dw.

• color laserjet mfp m277dw pro: the new Firmware update

  My M277dw printer is automatically downloaded and installed a firmware update last night.

  The datecode on the printer now shows 20160606.

  The update took me by surprise because I was in the middle of a print session.

  Is it a real update?  If yes where can I find the notes that this version is not on the driver download page.

  @Robert069,

  All the firmware update are directly from the HP Server. They are automatic HP where to connect to the network.

  I don't have details of which fixed the update but not yet posted to the customer of the USB. The update last two were to improve the network connection and built-in web server looks like.

  You don't have to worry about melware on the printer, as melware is a computer-based software. Can not be installed on printers.  Remember to update the printer firmware are link updateing the BIOS on a computer.

  I hope this helps.

• SOLVED: Slow wireless internet passthrough after firmware update

  If I first bought a Nighthawk in July 2014 and it was great for a while. Then in the notice happened a few months my streaming services are jumping and more than usual buffering (which was almost never with the Nighthawk).

  I have a connection of 110Mbps (Comcast and through a SB6141 modem), but all of a sudden was only getting 10 Mbps (or less) passthrough on 5 G wireless band (at the beginning of the speed test would sometimes up to 50 Mbit/s, but on a few seconds would fall to nothing..)

  Cable speeds were very good. Always 110Mbps +. Tried several different channels and factory reset the router, wireless speed was still slow. Connected to the Netgear website and submitted a support ticket within 2 hours they sent me with an RMA number and the next day a new unit has been FedEx would be for me. Support rep Tech says it's a problem of material known in some units... I was super impressed with the customer service, it was seriously a no replacement of hassles that took every 15 minutes of my time.

  EXCEPT when I got the replacement router in the next few days, he had the SAME PROBLEM. As soon as the new router is on and I'm connected, I've upgraded to the latest version of the firmware, done a factory reset and down Speedtest. And I had the same problem: speed internet passthrough on all my wireless devices has been terrible. Less than 10 Mbps when I have a connection 110 + Mbps. (Wired speeds were great, it was not a problem of modem or provider).

  Again contacted support and they asked me to download the latest firmware on laptop and upgrade the router manually, do a factory reset before and after the upgrade. They also told me to try to disable WMM (made no difference speed passthrough, but lower my laptop connection between 433Mbps to 54Mbps speed!).

  I tried this... still slow passthough wireless speed.

  The only thing that has changed since I first got a Nighthawk in July 2014 (and I've run speedtests then and had a speed 110 wireless + Mbit/s at the time), is that the firmware has updated several times... makes me think...

  I downloaded the Netgear support the past 5 versions of the firmware for the Nighthawk. http://downloadcenter.netgear.com/en/product/R7000#sear...

  I then manually downgraded the Nighthawk to each previous version (do a factory reset before and after each installation) and ran Speedtest every time. Once I have got down to the R7000 Version - V1.0.3.24_1.1.20 (released 12/02/14) and ran a Speedtest, the PROBLEM has BEEN RESOLVED. Speed wireless devices (laptop, HTC a M7 and iPad Air 2) were all back up to 110Mbps or more!

  Hope this experience helps someone else... If your are affected by the passthrough slow internet speeds and it is not your connection speed (i.e. radio parasites) that is the question, there seems to be a serious problem with the latest latest versions of couple... Try downgrading to the R7000 firmware version - V1.0.3.24_1.1.20

  UPDATE: Yes, I actually tested the speed with several different devices (a laptop HP HTC a M7 and Nexus 9) each on 5G band, all compatible with the latest updates ac. I also used a few test sites of different speed (speedtest.net, comcast speedtest, cnet speed test), not had the same result all devices and hosts.

  However, I actually got in touch with Netgear L2 support for the last month... beta test a few different versions of the firmware of the Nighthawk and even spend more than an hour on the phone one night with a nice guy who told me he was on an island in Southeast Asia, part of the Philippines... This is where Netgear technical support is to halfway between China where they build them and Taiwan where engineers are. After trying all tweak he could think for an hour and not get better speeds wireless, he finally dropped out and wished me a Merry Christmas lol. Not one of these beta firmware made a bit of difference, and I hate the hours that they made me screwing around with them!

  BUT today, they released vR7000 - V1.0.4.14_1.1.50 http://support.netgear.com/product/r7000

  And to my surprise it actually worked! Not only my high speed wireless is returned (120 + Mbps)

  http://www.Speedtest.NET/my-result/4078979293 (laptop)
  http://www.Speedtest.NET/my-result/a/1131321713 (nexus 9)
  http://www.Speedtest.NET/my-result/a/1131332778 (htc a m7)

  but also my Seagate SRD0SD0 previously incompatible (3 TB) USB 3.0 external hard drive works now, too. What a bonus! The reason I bought the Nighthawk was to use as Server DLNA and the monster external HD I picked up 6 months ago only was on the long list of those incompatible with this capricious router.

  But now everything works (at least for now).

  P.S. Maybe it's in my head, but I swear to you that since the last firmware update when running speedtest now or file transfer (while heavy streaming) I can hear the router doing a greater slope electric buzzing/hissing noise is a little disconcerting... I'm not sure my brain fried by overclocked wifi will be worth a high speed in the end...: eek:

• Wan interrupts the connection after the firmware update

  Looks like the latest firmware upgrade is the source of the problems.

  I've just updated my timecapsule 1 TB of first generation version 7.6.7 and my 3 TB timecapsule new version 7.7.7

  Both are connected to the router of the provider of Internet services and extend the network even in my house.

  WiFi is stable until the upgrade, but now the connection is lost every few minutes or seconds.

  Both versions are later to the respective timecapsules.

  I end up having to downgrade if no solution is found.

  I powered the two market still nothing does not. Redefine the network and tried both hidden and not hidden, yet once nothing doesn't.

  Any ideas on what is causing the problem?

  Well, since nobody seems to have an explanation, and Apple are not out with firmware update after 7.7.7 and 7.6.7 I decided to downgrade the firmware to the previous version. I now run version 7.7.3 on the new 3 Tb Time Capsule and 7.6.3 on the 1st Gen Time Capsule. So far, the network is stable. Using WiFi Explorer Ii see that they use channel 6 and 8 respectively. Signal is strong and no dropouts have taken place so far. Hope the issue is resolved in the next firmware update.

  As I read in another post: firmware update does not solve a problem, you didn't. However, it can create a problem that you didn't.

• Workstation xw4600: upgrade CPU to Xeon X 3363 xw4600 - get error on POST firmware update

  Until classified Core 2 Duo 8400 3.0 Mhz CPU to Xeon X 3363 2.83 Mhz CPU using 'Sticker Mod' on X 3363.

  Works fine, but with an error at startup.

  Get this error on the POST:

  "1801 Microcode Update error-
  Missing or invalid processor update. Please
  Contact Hewlett - Packard Company for a new firmware
  Updated to support the new processor not. »

  The current version of BIOS is 1.34 which I think is the most recent.  How to upgrade the BIOS to the Stepping of the processor?

  Use a xw6600 or an update of the BIOS z400?

  I was able to get help on changing the Bios microcode for the Xeon x 3363 processor.

  Fans to run at normal speed now and start error "1801" disappeared.  Machine runs great!

• Unable to launch SSD Q300 HDTS748EZSTA firmware update

  This player has a fresh install of Win7.

  Currently on SAFM11.1 and want to update to 11.2

  No other programs are running by the utility of the list firmware update "before you begin".

  The following message is received after the warning on the reboot of the pc:

  Impossible to prepare the system to update the native mode. Try again or contact technical support.

  What should I do to get past this error? I have to start this process all in safe mode?

  You must run the update of the firmware in safe mode. (Even if the system is loading press F8 and use mode safe mode with LAN). But there is a problem after update the firmaware.
  If you use TOSHIBA Storage Utilities v3.10 there is a possibility that your system crashes (you should first uninstall it).

  There is no possibility of connection to Windows after restart. I did an experiment and after formatting SSD, I installed a new copy of Windows 7 Pro SP1. The result was the same, it worked until the installation of the utilities of storage TOSHIBA v3.10.

  There is clearly a software problem, but I have not found another solution (do not to install the utilities of storage TOSHIBA v3.10)

• Thunderbolt Display Firmware update could not complete.

  Hello.

  Am myself a brand new Mac Pro recently and I'm loving it. Hooked up to my old TB screen which is unused to cause a few months the all-in-one cable is broken. Not much, I bought a cable TB, and used only to plug it in and it works fine.

  That is, until I went in the App Store and noticed a firmware update for display among all other system updated. I do not think that anything of it in time and just continued to download and install all updates in bulk. Well, after all has been said and done I got the popup saying he could not apply the on-screen since it must route the cable all-in-one to do. Not a problem, I thought, it's not that important to me it is installed. But now after whenever I restart the machine, I get the annoying popup even in my face, no matter what I try to do to remove it. I'm fine with not getting updated, I just want this bitch popup go away!

  I am a very advanced user, so I am not against the orders of terminals and/or editing plists performer or that you have to solve this problem. I don't know where to look and I thought this would be my last ditch effort fixing before you say screw it, wipe the system and start over. If no preview of this would be useful. Thank you.

  Apple doc:

  Thunderbolt Firmware Update 1.2: continues to reappear and Thunderbolt ports and target Display Mode may not work

  After the installation of Thunderbolt Firmware Update 1.2:

  • The Thunderbolt ports may not work.
  • Target display mode may not work.
  • The update can keep reappearing as available for download.

  This happens when one Thunderbolt self-powered (other than one directly connected Thunderbolt display) device is connected to a Thunderbolt port during the installation of the update. To resolve this problem:

  1. Shut down your computer.
  2. Disconnect all devices Thunderbolt.
  3. Wait for 10 seconds.
  4. If you use a Mac mini with a Thunderbolt screen, reconnect the Thunderbolt display directly to your computer via the Thunderbolt port. Do not connect other devices Thunderbolt at the moment.
  5. Restart your computer.
  6. If sight Firmware 1.2 update is available, download and install and restart your computer when asked. If the update of Thunderbolt is not available, the update has been successfully installed.
  7. Reconnect all devices Thunderbolt.

• Toshiba 40SL980G - the Youtube app after the firmware update.

  Hello

  So today, I've updated the firmware of my TV (40SL980G) and after the update of the youtube app is missing and also the social place of Toshiba places is not accessible.

  I did reset TV after the update.
  I checked the firmware download page, but this model is not which are listed there.

  Someone here could help me on how to solve this problem I would really appreciate it.

  They are probably going to change something in the places of Toshiba.

  If a new firmware update is available, try to install the latest version.
  Otherwise I recommend the service Toshiba Places in the next few days again.