new firefox user, cannot access gmail

Similar Questions

• New user cannot access any area of activity

  Hi, I use Discoverer Desktop 9.0.4.43.17 and administrator of 9.0.4.43.18 and I have a new user cannot access any sector of activity, I tried to create a new business district to test and access the Security window on the Client of Directors for this user and my user (works very well!), for my user that this new BA shows normally on the desktop but for new user the selection of business on Assistant workbook area shows nothing. It's something to measure new users to access the space business?
  
  Published by: user2997975 on 06/04/2009 07:19

  Hello
  As suggested by Rod it sounds as if you may have several EUL in the same prod73. Try to connect again, but this time go to tools | Options and click the EUL. It is the last tab on the right side and you may need to click the button to the right (next to connection) several times before seeing the EUL tab.

  Under the EUL tab, make sure that the EUL you want to connect is selected. If it is bad you will need to change it, click on the OK button and then reconnect to the database using file | Connect to the database.

  This time you must point to the right EUL.

  Best wishes
  Michael

• Can not connect - when entering a password message "the service user profile service has no logon. Failed to load profile \User' cannot access start menu to apply the options.

  Can not connect - when entering a password message "the service user profile service has no logon. Failed to load profile \User' cannot access start menu to apply the options.

  Hello

  1st thing to try is the system in safe mode restore to before the problem

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not solve it read more

  read the tutorial below

  http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  When you log on a Windows Vista-based or a Windows 7 computer by using a temporary profile, you receive the following error message:

  The user profile Service has not logon. User profile cannot be loaded.

  http://support.Microsoft.com/kb/947215#letmefixit

  Your user profile was not loaded correctly! You have been logged on with a temporary profile.

  http://support.Microsoft.com/kb/947242

  If you tried to log on to Windows and received an error message telling you that your user profile is damaged, you can try to fix it. You will need to create a new profile and then copy the files from the existing to the new profile. You must have at least three user accounts on the computer to perform these operations, including the new account that you created.

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

• Error message: Windows cannot access the specified device path and the second user cannot access the internet

  Original title: I have two users on Vista. We get to the top with windows can not access the specified device path.etc. The other has no problem

  The second user cannot access the internet. Can't access window appears. The other user is not problems.

  Hi Rickravel,

  1. what type of account you use?

  2. This only happens when you access Internet?

  3. when the problem started?

  4. you remember to make changes to the computer before this problem?

  Step 1:

  You can start in safe mode with network and see if the problem occurs in the account.

  You can see the following link to start in safe mode with network.

  Start your computer in safe mode

  Note: Restart the computer to boot into normal mode.

  Step 2:

  If you use Internet explorer, then you can try to disable add ons and check if it helps:

  Run Internet explorer with no Add - ons. Steps to open Internet with no mode of modules:

  a. click on start

  (b) in the search box, type in Internet explore

  c. Select Internet (no add-on mode)

  If you were able to access the Web site without any problems, then the module may cause the error.

  You can read the following article and try the steps to activate the modules individually determine which Add - ons may be the cause of the problem.

  How the modules of the browser affect my computer?

  Hope this information is useful.

• User cannot access local drives

  Win7 - 64 bit - new out of the box – users of local computers work fine - joined the field - add a domain user as a domain account user - user 'all programs' missing - administrator can access the shares of domain - domain user cannot see local readers - domain cannot run command line programs - domain user has been deleted and restored - changed permissions on the C drive for everyone «» total control"= thank you

  Hi Thensley,

  Thanks for posting your query in Microsoft Community.

  I understand that you have problems with the domain user account.

  The question you have posted is would be better suited to the Technet community.

  Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en/w7itpronetworking/threads

  Hope it will be useful. If you still have questions, please reply and we will be happy to help you.

• Other users cannot access the Internet

  I'm helping a friend with his pc and she and her husband have their on user accounts on Dell Dimension 8400 with a Verizon FIOS connection.  We were above to delete a message and then she went into the internet and the lights went out in the House and back but now she cannot access the internet.  Her husband can in his story, but she can't.  I tried to create a new user to see if it has been altered for the failure, but still cannot access the internet.

  It opens the Web page but does not display anything, and freezes.   Any help would be greatly appreciated.

  Nancy
  
  

• VPN users cannot access Tunnel

  Hi all

  I have a problem, I have 2 sites both with ASA 5520, they are both connected via a site to site VPN.

  It works very well all users in site A can access resources in site B and vice versa.

  The problem comes when a user connects to a remote user VPN site has they cannot access or anything in site B same ping if the FW them delivers an ip address in the range for the site.

  Im sure there is something simple that I missed.

  Thank you

  If the VPN Client pool is in the same subnet as the site of A LAN, then you are probably missing just the following:

  (1) check if you have divided political tunnel, and site-B LAN is included in the ACL split tunnel.

  (2) configure 'same-security-traffic permit intra-interface' on the site A ASA.

  If the above has been configured, please share configuration the two ASA to further check where it is.

• AnyConnect VPN users cannot access remote subnets?

  I googled this until blue in the face without result.  I don't understand why Cisco this so difficult?  When clients connect to the anyconnect vpn, they can access the local subnet, but cannot access the resources in remote offices.  What should I do to allow my anyconnect vpn clients access to my remote sites?

  Cisco 5510 8.4

  Hello

  What are remote sites using as Internet gateway? Their default route here leads to the ASA or have their own Internet gateway? If they use this ASA for their Internet connection while they should already have a default route that leads traffic to the VPN to the pool, even if they had no specific route for the VPN itself pool. If they use their own local Internet gateway and the default route is not directed to this ASA then you would naturally have a route on the remote site (and anything in between) indicating the remote site where to join the pool of 10.10.224.0/24 VPN network.

  In addition to routing, you must have configured for each remote site and the VPN pool NAT0

  Just a simple example of NAT0 configuration for 4 networks behind the ASA and simple VPN field might look like this

  object-group network to REMOTE SITES

  object-network 10.10.10.0 255.255.255.0

  object-network 10.10.20.0 255.255.255.0

  object-network 10.10.30.0 255.255.255.0

  object-network 10.10.40.0 255.255.255.0

  network of the VPN-POOL object

  10.10.224.0 subnet 255.255.255.0

  NAT static destination DISTANCE-SITES SITES source (indoor, outdoor) REMOTE static VPN-VPN-POOL

  The above of course assumes that the remote site are located behind the interface 'inside' (although some networks, MPLS) and naturally also the remote site networks are made for the sake of examples.

  Since you are using Full Tunnel VPN should be no problem to the user VPN transfer traffic to this ASA in question.

  My first things to check would be configuring NAT0 on the ASA and routing between remote sites and this ASA (regarding to reach the VPN pool, not the ASA network IP address)

  Are you sure that the configuration above is related to this? Its my understanding that AnyConnect uses only IKEv2 and the foregoing is strictly defined for IKEv1?

  -Jouni

• Standard user cannot access program (event id 882) installed on windows 7 home 64 bit.

  It's driving me crazy.  Whenever a user attempts to open a program already installed, nothing happens.  The event viewer displays the event id 882.  The laptop is running windows 7 home so it doesn't have the local security policy that I can change.  How to disable this check or allow the program is accessible by standard users?

  I solved the problem.  I downloaded and installed gpedit.msc following the instructions here - http://www.askvg.com/how-to-enable-group-policy-editor-gpedit-msc-in-windows-7-home-premium-home-basic-and-starter-editions/

  Once this was done, I was able to change the policy to allow the user to access the new application.

• User cannot access network drives.

  Using Anyconnect 2.5 and ASA 5510. When a user connects to the VPN, DNS suffixes change settigs ' Append primary "to"Add these suffixes." (See below)

  The suffix PublicDomain.com is listed as the default domain in group policy. The problem I have is that a particular user can not see the network drives. If I ping the server that drives mapped, I get an audience to an IP address. If I ping server. OfficeComputerDomain.com I have the right internal IP address. So, if I manually change the order and OfficeComputerDomain.com first of all, the user can access without problem network drives. Can I first set up the VPN profile to the OfficeComputerDomain.com list or can I just change the default domain in the group to my internal domain name policy?

  Thank you

  

  Yes, you can change both in the related group policy configuration.

  attributes of group policy
  value by default-field OfficeComputerDomain.com
  Split-dns OfficeComputerDomain.com PublicDomain.com UserHomeDomain.com value

• New user cannot access the transferred music draws on Windows Media Player 11

  I just added a new user to my window 11 downloaded pc game on there it does not show the music I would also transfer music from my library in library here and can u help me with these problems

  Library to point to the folder monitored by the player

• My Firefox browser cannot access the Internet, so I use my iPad.

  I forgot that I have to use my iPad email. My office is not talking about the Internet this week. Troubled shooters are no solution. The closest I can come the problem is a message from the homepage on chrome. It says 'DNS probe finished. "
  no internet"not much to go for me in any case. Appreciate any help that anyone can provide. I suspect a proxy problem, but it's way above my head. I am former over the years and the new in computer talk, so be simple in steps to resolve. Thank you. George sends.

  _{Edit: removed personal information for your protection. (philipp)}

  Type of topic: preferences #advanced< enter > in the address bar.

  Under Advanced, select network.
  Search for configure how Firefox connects and then press the settings button.
  If you use a proxy server, make sure that these settings are correct. If there is no
  proxy, first use No. Proxy. If there is a problem, then try Proxy system.

  Some problems occurs when your Internet security program has been implemented.
  trust the previous version of Firefox, but not more acknowledges your
  update as being approved. Now how do I solve the problem: to allow
  Firefox to connect to the Internet

  • Make sure your Internet security software is up-to-date (for example, you are using the latest version).
  • Delete Firefox to list your program of programs approved or recognized. For detailed instructions, see

  Configure the firewall so that Firefox can access the Internet. {web link}

• New firefox user interface is just ugly

  I want to say that I am a very loyal user and have been using Firefox for beta versions. And this is my first post of this nature.

  We've been through a lot, a lot of redesigns, updates etc. I really grew to rely on firefox as tool and instrument. And since that time those updates were logical and had a direction. But today I've upgraded to 29, and I've just couldn't believed my eyes to see how unpractical and uncomfortable everything is now. You've taken the small things that I've accustomed to, you took freedom to manipulate browser in any way I, not YOU, but ME, want to use MY browser. YOU want whole new look is fine with me, make it choseable, don't force it, if it's good migration will follow, but now it's definitely a mess and for first time in 10 years firefox I will be considering firefox as my second-choice browser until (if ever) that mess cleans up.
  

  Amen corsR. This new change struck me today too and it is really terrible.

  Fortunately, there is an add-on that restores at least a semblance of decent what FF28- https://addons.mozilla.org/en-US/firefox/addon/classicthemerestorer/

  It is not as good as the original, but it's a hell of a lot better than the current design, by a wide margin.

• Second user cannot access - Windows XP program files

  I just added my wife as a second user on my PC (Windows XP Home).  I created it as administrator too.  When you are logged as long as him, none of the programs installed under Program Files are accessible.  The icons appear on the desktop, but if I click on them, a pop-up box says windows cannot find c:\Program Files\whatever.  If I choose the option browse on the popup and click in Program Files, I get an error "C:\Program Files is not accessible.  Access Denied»  I did some research on this forum and got answers on the selection/deselection of use sharing simple file under Tools-> view-> advanced settings.  But this option is not available, because it is XP Home, XP Pro not.

  Certainly, she should be able to access the programs in this folder.  What Miss me?

  Hello

  try restarting the WIndows XP Home edition in 'safe mode', then you can see the tab 'Security' in the properties windows of the folder "Program files" - you should see that this rights:

  https://SkyDrive.live.com/#CID=23FD66EFD8D06B76&ID=23FD66EFD8D06B76%21269

  Directors - have all rights (this folder, subfolders and files)

  CREATOR OWNER - has all the rights (only files and subfolders)

  SYSTEM - has all the rights (this folder, subfolders and files)

  Users (...) -have read & run, view the contents of the file, reading (this folder, subfolders and files)

  LC

• the user cannot access table

  Hi, I created a new user
  
  CREATE a USER "sue" PROFILE "DEFAULT" IDENTIFIED BY "dbsuepwd" DEFAULT TABLESPACE "ERDBPERM".
  
  TEMPORARY TABLESPACE "ERDBTEMP" ACCOUNT UNLOCK;
  
  and certainly privalges access limited so that users can insert a line on a chart, but not to delete all data.
  
  GRANT CREATE SESSION to prosecute;
  GRANT INSERT ON EXPENSEREPORT TO "sue";
  
  but now when I connect to the database using sql developer usind sweating account iam not able to insert data into the table expensereport
  
  Error report:
  SQL error: ORA-00942: table or view does not exist
  00942 00000 - "table or view does not exist.
  * Cause:
  * Action:
  
  Help me time user and table exist on same tablespace.
  
  Please say what privileges I used to give the user.

  Hello

  Same is the case with the sequence that he was with the table. Synonym EXPENSEREPORT_SEQ. NEXTVAL isn't in the same schema from which you run the statement. If you give the privilege object SELECT the sequence EXPENSEREPORT_SEQ. NEXTVAL to your new user for the execution of this statement.

  I hope this helps.

  -Gregory