New meeting place 8 Pro 3000 (2014) - WiFi VERY slow speed

Similar Questions

• Lost power 'high performance' profile on the meeting place 8 pro

  I only see the option 'Balanced '. I remember when I had first tablet, I had two options... one for balanced and another for performance.

  How can I return these options? At the very least, that someone can point out their profile for their meeting places 8 pro settings?

  Also, I see no popup 'low battery'... the tablet will shut down without any warning when the battery is low.
  Thanks in advance.

  That has something to do with the sleep settings connected / configuration Dell made on these units. It is the same for versions place 11 MS Pro. units of vPro are different because no standby connected supports.
  If you turn off the connected Eve all Windows power plans are displayed and all the advanced features of power are available.

  Use the command Regedit and change the following:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Power
  Change the value for the key CsEnabled from 1 to 0 and reboot.

  1 means connected off standby active and 0.
  Try it and see if it solves your problem.

  BTW: by disabling the connected standby battery also will show the time remaining not only the percentage of battery life. :-)

• Satellite Pro A100 carpet * dvd uj - 841 s write at very slow speed

  Hello.

  The carpet * a dvd multi drive uj - 841 s that came with my satellite pro a100 written on very slow DVD. Firmware 1.50
  I use good philips and kodak media (both rated 16 X).

  now, I know that the drive is only rated at 8 X max. But I can't even reach 6 X.

  A firmware update would solve this?

  Thank you very much.

  Hello

  To my knowledge, some burning applications control the burning speed to obtain the best possible results from burning
  As you probably n t know the speed of combustion higher risk of burn errors
  I burn my DVD only using a single 1 x speed.

  Then I can be sure that all DVD players would be able to play the burned DVD.

  Greetings

• installed the new windows Friday and since my computer is very slow and not connecting to internet properly

  installed the new windows Friday and since my computer is very slow and not connecting to the internet correctly... anyone else having these issues?

  System Restore to go back before the show.

  I suggest you to install the updates one by one and reboot the computer after installing each update to verify that update is causing the problem.

  Also note the updates that you install on the computer.

  Once you come to know what update is causing the problem, let us know.

  Do not install any driver updates offered by Windows Update. Find them in the manufacturer's website instead.

  Try a convenience store

  Windows includes two programs of troubleshooting that you can use to automatically fix some common problems with performance on your computer or to the maintenance of your system.

  Open the Performance troubleshooting utility by clicking the Start button, then Control Panel.

  In the search box, type Troubleshooting, and then click Troubleshooting.

  Under system and security, click check for performance issues.

  Open the of System Maintenance Troubleshooter by clicking the Start button, then Control Panel.

  In the search box, type Troubleshooting, and then click Troubleshooting.

  Under system and security, click run maintenance tasks.

  08/14 / 1115:46: 45 pm UTC

• Offers day and slow downloads WiFi (very slow).  Is there a way that I can download some updates and new programs using my macbook pro (to a public site in the city) and transfer it on my iMac which is too heavy to cart autour?

  Difficulty to access the updates and downloads with very slow wifi ("country").  Is it possible that I can download some updates and new programs using my MaBbook Pro (retina) on a public site in the city and transfer them on my iMac which is too heavy to cart autour?

  New programs, Yes.

  Updates, depends on what you're updating.

• Cannot get card GeForce GTX 560 Ti CUDA to work with the new version of first Pro CC 2014

  In the past, I was able to get CUDA on my GeForce GTX 560 Ti card to work with the Mercury playback engine by adding 'GeForce GTX 560 it' in the file cuda_supported_cards.txt. But with the new version of CC 2014 first, this file is not in the repertoire of Premiere Pro more. Is there a way to get my GTX 560 it be listed as a card support for CUDA with CC 2014?

  So, I thought about it.  I installed the latest graphics driver, and then open the NVIDIA Control Panel.  Here, I've selected "Manage 3D settings" and went to the 'Program settings' tab  I chose Adobe Premiere (adobe first pro.exe) in the list and under the function of "CUDA" - GPU, I changed to "Use these GPU" and selected my GTX 560 it (which was the only one listed).

  After that, I opened the first Pro CC 2014 and selected 'Project Settings - général' and was therefore able to choose "Mercury Playback Engine GPU acceleration" under Renderer (which was unavailable).

  I hope this will help someone else if they encounter the same problem.

• My macbook pro mid-2012 is very slow. Do I need a new battery?

  Hello world

  Support on this community has helped me tremendously before so I thought I'd post again about a new problem.

  I upgraded my Mac with an SSD, which works very well, with more RAM; However, recently, it has been very slow and train, and I don't know why. RAM is not being crazy, so it must be something else.

  After reading the other posts, I'm thinking maybe I need a new battery? I mean I have 893 cycles ahah. Could someone help with this?

  Here is my log of Etrecheck:

  EtreCheck version: 2.9.12 (265)

  Report generated 2016-06-07 02:57:40

  Download EtreCheck from https://etrecheck.com

  Time 01:38

  Performance: Excellent

  Click the [Support] links to help with non-Apple products.

  Click [details] for more information on this line.

  Problem: Computer is too slow

  Hardware Information: ⓘ

  MacBook Pro (13-inch, mid-2012)

  [Data sheet] - [User Guide] - [warranty & Service]

  MacBook Pro - model: MacBookPro9, 2

  1 2.5 GHz Intel Core i5 CPU: 2 strands

  8 GB of RAM expandable - [Instructions]

  BANK 0/DIMM0

  OK 4 GB DDR3 1600 MHz

  BANK 1/DIMM0

  OK 4 GB DDR3 1600 MHz

  Bluetooth: Good - transfer/Airdrop2 taken in charge

  Wireless: en1: 802.11 a/b/g/n

  Battery: Health = battery check - Cycle count = 893

  Video information: ⓘ

  Graphics Intel HD 4000

  Color LCD 1280 x 800

  Software: ⓘ

  OS X El Capitan 10.11.5 (15F34) - since startup time: less than an hour

  Disc information: ⓘ

  500 GB SAMSUNG SSD 850 EVO Disk0: (500,11 GB) (Solid State - TRIM: Yes)

  EFI (disk0s1) < not mounted >: 210 MB

  SAMSUNG SSD 850 EVO 500 G Media (disk0s2) /: 499,11 go-go (287,31 free)

  Recovery HD (disk0s3) < not mounted > [recovery]: 650 MB

  MATSHITADVD-R UJ - 8À8)

  USB information: ⓘ

  Apple Inc. FaceTime HD camera (built-in)

  Apple Inc. Apple keyboard / Trackpad

  Computer, Inc. Apple IR receiver.

  Apple Inc. BRCM20702 hub.

  Apple Inc. Bluetooth USB host controller.

  Lightning information: ⓘ

  Apple Inc. Thunderbolt_bus.

  Configuration files: ⓘ

  / etc/hosts - number: 20

  Guardian: ⓘ

  Any where

  Kernel extensions: ⓘ

  / Library/Extensions

  [loading] com.globaldelight.driver.BoomDevice (1.4 - SDK 10.10 - 2016-06-03) [Support]

  Launch system officers: ⓘ

  [loaded] 8 tasks Apple

  [loading] 162 tasks Apple

  [operation] 68 tasks Apple

  Launch system demons: ⓘ

  [loaded] 47 tasks Apple

  [loading] 163 tasks Apple

  [operation] 81 tasks Apple

  Launch officers: ⓘ

  [failure] com.adobe.ARMDCHelper.cc24aef4a1b90ed56a... plist (2016-05-12) [Support]

  [loading] com.google.keystone.agent.plist (2016-03-02) [Support]

  Launch demons: ⓘ

  [loading] com.adobe.ARMDC.Communicator.plist (2016-05-12) [Support]

  [loading] com.adobe.ARMDC.SMJobBlessHelper.plist (2016-05-12) [Support]

  [loading] com.adobe.fpsaud.plist (2016-05-09) [Support]

  [loading] com.bombich.ccchelper.plist (2015-11-30) [Support]

  [loading] com.google.keystone.daemon.plist (2016-03-02) [Support]

  [loading] com.microsoft.office.licensing.helper.plist (2015-01-16) [Support]

  [loading] net.freemacsoft.LiteIcon.LIHelperTool.plist (2014-08-26) [Support]

  [loading] org.cindori.SenseiTool.plist (2015-12-03) [Support]

  [loading] org.cindori.TEAuth.plist (2015-12-03) [Support]

  org.eyebeam.SelfControl.plist [no charge] (2016-04-28) [Support]

  User launch officers: ⓘ

  [failure] com.adobe.ARM. [...]. plist (2016-01-09) [Support]

  Items in user login: ⓘ

  Workflow application (/ Applications/Flux.app)

  PopClip application (/ Applications/PopClip.app)

  BetterSnapTool application (/ Applications/BetterSnapTool.app)

  Alfred 2 Application (/ Applications/Alfred 2.app)

  ClipMenu application (/ Applications/ClipMenu.app)

  Decision on application (/ Applications/Hear.app)

  Fan of Macs control application (/ Applications/Mac Fan Control.app)

  Hocus Focus application (/ Applications/Hocus Focus.app)

  Other applications: ⓘ

  [operation] 2BUA8C4S2C.com.agilebits.onepassword - osx-helper

  [ongoing] com.crystalidea.MacsFanControl.60192

  [ongoing] com.etresoft.EtreCheck.207712

  [ongoing] com.globaldelight.BoomDaemon

  [ongoing] com.google.Chrome.163232

  [ongoing] com.hegenberg.BetterSnapTool.49632

  [ongoing] com.naotaka.ClipMenu.52192

  [ongoing] com.pilotmoon.popclip.291872

  [operation] com.runningwithcrayons.Alfred - 2.166432

  [ongoing] com.uglyapps.HocusFocus.264992

  [ongoing] org.herf.Flux.119072

  [loading] 412 tasks Apple

  [operation] 173 tasks Apple

  Plug-ins Internet: ⓘ

  o1dbrowserplugin: 5.41.3.0 - 10.8 SDK (2015-12-15) [Support]

  GameFacePlugin: GameFacePlugin 1.8.0.1 - SDK 10.5 (2012-11-16) [Support]

  Unity Web Player: UnityPlayer version 5.0.3f2 - SDK 10.6 (2015-08-04) [Support]

  Default browser: 601 - SDK 10.11 (2016-05-17)

  AdobeAAMDetect: AdobeAAMDetect 1.0.0.0 - SDK 10.6 (2015-11-30) [Support]

  FlashPlayer - 10.6: 21.0.0.226 - SDK 10.6 (2016-04-21) [Support]

  AdobePDFViewerNPAPI: 15.010.20060 - SDK 10.8 (2016-03-11) [Support]

  Silverlight: 5.1.30514.0 - SDK 10.6 (2015-11-30) [Support]

  QuickTime Plugin: 7.7.3 (2016-05-17)

  Flash Player: 21.0.0.226 - SDK 10.6 (2016-04-21) obsolete! Update

  googletalkbrowserplugin: 5.41.3.0 - 10.8 SDK (2015-12-11) [Support]

  PepperFlashPlayer: 21.0.0.242 - SDK 10.6 (2016-06-07) [Support]

  AdobePDFViewer: 15.010.20060 - SDK 10.8 (2016-03-11) [Support]

  SharePointBrowserPlugin: 14.4.8 - SDK 10.6 (2015-02-26) [Support]

  JavaAppletPlugin: 15.0.1 - SDK 10.11 (2015-11-30) check the version of

  User Plug-ins internet: ⓘ

  samesurf_screenshare_32: Unknown (2014-08-10)

  Safari extensions: ⓘ

  1Password - AgileBits - https://agilebits.com/onepassword (2015-09-10)

  AdBlock - BetaFish, Inc. - https://getadblock.com (2015-09-27)

  Adblock more - Eyeo GmbH - https://adblockplus.org/ (2015-09-27)

  ClickToFlash - Marc Hoyois - http://hoyois.github.com/safariextensions/clicktoplugin/ (2015-08-04)

  Audio Plug-ins: ⓘ

  Hear: 1.1.6 - SDK 10.8 (2014-11-03) [Support]

  3rd party preference panes: ⓘ

  Flash Player (2016-05-09) [Support]

  FUSE for OS X (OSXFUSE) (2015-10-25) [Support]

  Time Machine: ⓘ

  Mobile backups: OFF

  Automatic backup: NON - automatic backup disabled

  Volumes to back up:

  Destinations:

  Seagate 3TO [Local]

  Total size: TB 3.00

  Total number of backups: 4

  An older backup: 2014-12-12, 14:35

  Last backup: 2015-11-23, 08:35

  Size of backup drive: Excellent

  Size of backup 3.00 TB > (disk size 0 B X 3)

  Top of page process CPU: ⓘ

  67% Google Chrome Helper (6)

  37% Google Chrome

  6% kernel_task

  6% WindowServer

  2% PopClip

  Top of page process of memory: ⓘ

  770 MB Google Chrome Helper (6)

  Kernel_task 747 MB

  Chrome Google 188 MB

  Mdworker (9) 172 MB

  Mds_stores 164 MB

  Virtual memory information: ⓘ

  4.25 GB free RAM

  used 3.75 GB RAM (1.70 GB being cached)

  Used Swap 0 B

  Diagnostic information: ⓘ

  7 June 2016, 02:50:29 self-test - spent

  Hello. Try restarting your Mac.

  Try to start:

  -Stop your Mac

  -Wait until your computer turns off and after that press the power button

  -Just after you hear the startup tone, press in and hold the SHIFT key

  -Release the SHIFT key when you see a gray Apple sign and the progress under this sign bar

  -Once your Mac boot, restart dhcpd as you usually do.

  If this does not help, follow the instructions below:

  -Stop your Mac

  -Wait until your computer turns off and after that press the power button

  -Just after you hear the startup tone, press in and hold the SHIFT key

  -Release the SHIFT key when you see a gray Apple sign and the progress under this sign bar

  -Once you see office, start a scan Disk Utility to detect and repair file system errors (remember to choose your primary hard drive)

  -Click on the disc to check, then, if requested to solve the problems on the repair disk

  -After that click on verify disk permissions, and then click Repair disk permissions

  -Once the process is complete, stop your Mac and turn it on again after 30 seconds

  Apart from this, take a look at this article from Apple and follow the instructions to reset NVRAM shown here:How to reset the NVRAM on your Mac - Apple Support

  Try resetting the system management controller: https://support.apple.com/en-us/HT201295

  I also suggest upgrading your RAM.

  I hope this helps!

• New Satellite Pro U400-12y is very slow

  Just bought Satellite Pro U400-12y with Vista Business pre-installed (1 GB preinstalled memory).
  However, the startup is very slow and actually the computer seems to work in a time warp.

  Any ideas? Is there a fundamental problem?

  Yes, I have an idea.

  I think that the high amount of background processes affect the performance of laptops.
  He should know that the U400 supports many different features and these features are controlled by different applications.

  If you want you can start the msconfig and disable some unnecessary and unimportant process. Take a look in the Startup tab.

  In addition, I recommend to disable and remove the preinstalled software called Tempro.

  I did it on my system, and now it runs much faster

• Satellite Pro M70-113: modem - very slow

  Hello

  I have a toshiba satellite pro m70-113 laptop. I bought it in Saudi Arabia, Riyadh.

  The problem is that when I use the modem (dialup) software from toshiba to connect to internet... the connection is very very slow... While on the same line, on my desk speed isn't a problem... on average, I get 1/4th of the speed I get on my desk... and on the same telephone line...

  What is the problem?

  Can someone help me in this... are there any configuration software that can fix this problem?

  Help will be very appreciated...

  Thank you.

  Hello

  I don't know what your desktop device modem, but modems takes care of different speeds.
  You can also check the properties of the modem for laptop.
  Go to the Toshiba software modem properties and check under the tab "modem".
  You will find the maximum port speed. This should be set to the highest value.

  It is also possible that different providers use a different speed of data transmission.
  Some time ago I used a modem and I was very surprised that my speed of data transmission is different on the different suppliers.
  As you can see there are many factors why you don? t get the same speed of modem.

• New HP Envy M6 only detect ethernet cable, very slow wifi

  Hello

  Sometimes, the wifi, I get 1mpbs on a 50mpps connection. I'll upload to 5 Mbps, which is normal (but why are my download speeds so slow?) Laptops and other devices work perfectly. Closer to my wireless router (well it's not a router, it is a TG862 of Arris Comcast) seems to alleviate the problem, but... I am no farther than 25 feet away from him in my room!

  I tried to solve this problem by updating the BIOS and the driver Qualcomm Atheros 9485 and apparently not helped at all.

  My concern REALLY, it's THAT EVERYTHING, nothing happens when I plug my ethernet cable into the left side of my laptop. It is in the correct port. It works fine in my xbox, my other laptop and my desktop computer. Other ethernet cables do not work or the other. I noticed there are two holes (which resemble lights) that don't light up, right where I plug the Ethernet cable.

  http://support.HP.com/us-en/document/c03363657

  I followed these instructions piece by piece without success.

  Should I have a burst network card? Help, please! This notebook is so new and brilliant, my other is old and destroyed and won't even take a load! I greatly appreciate it.

  Michael Siraco

  Hello Dollarsignrack,

  You have a problem with your network connection.

  It could be a defective material you may be substituted.

  First, turn off the computer.
  That you put it on press the F10 key. This will load the BIOS setup utility.
  Press F9 to load the default values.
  Press F10 to save and exit.

  This should help to detect the Ethernet port.
  When the computer starts up, check if everything is working.

  If it is still slow to go to HP.com and update the BIOS and software framework.

  Here are links to the updates.

  BIOS

  Software structure

  If you do not need to have the unit repaired.

  Here is a link to the phone number that you can call to HP.

  By clicking on the White Star congratulations on the left is a way of saying thanks!

  I would like to know how everything goes.

  Nice day.

• 15 - ac151dx: wifi very slow when unplugged from charger

  Hello

  I have a new laptop of HP 15-ac151dx. Right out of the box, I noticed that the company becomes exteremly slow when I unplug the charger.  As soon as I plug in the charger, the speed is very good.  It works fine on a wired connection with the charger plugged in or unplugged.

  So far, I tried the following, and nothing worked:

  1. turn off the laptop, to reset the router, turn on laptop

  2. remove the checkmark beside: ALLOW the COMPUTER TO TURN THIS DEVICE OFF SAVE tab managemnt Realtek RTL8188EE wifi power adapter.  I also didi this on Realtek PCIe FE Family Controller.

  3. went in the settings of advanced and equal "battery power" parameter settings "plugged in."

  4. Rinse the DNS

  5 reset the TCP/IP stack

  6 driver adapter wifi update to 2023.18.814.2015 to 2023.27.1230.2015

  7. update of Windows Ran

  8. check the BIOS for power management setting, but can't find anything

  9 exchanged the laptop - always have the same question.

  Are there other settings that can I can check?  Looks like a setting simple power management, I'm missing somewhere.

  Thank you very much.  In fact, it's a driver problem.  I have done the following:

  1 restore BIOS to factory settings

  2 uninstall the WLAN driver

  3. scan for hardware changes in the action menu in the Manager of devic

  4 reboot

  5 HP Recovery Manager--> reinstall WLAN drivers

  6 reboot

  7. HP support--> latest install Web site drivers WLAN

• WiFi very slow to reconnect after sleep or Hibernate (or even at all)

  Hello everyone, I have seen similar topics on this topic before, but none of the solutions have worked for me. I am unable to connect to any WiFi after my return to laptop computer to a low power mode (sleep or Hibernate) for sometimes the lengths of time up to 2 minutes. Either an orange star/circle shape appears in the on the icons wireless system tray saying network connections are available, or the icons of progress of rotation turns constantly and never connects. If I want to restore the network connection, I have to restart my computer, or disable and reactivate the NIC (Intel WiFi Link 5300AGN) wireless.

  Things, I tried to fix the problem:

  • Uncheck the box "Allow the computer to turn off this device to save power" under power management in the wireless adapter, properties of the device AND hub USB root
  • Change my power Plan to High Performance and set the parameters for the adapter wireless for 'Maximum Performance '.
  • Turn the empty screen saver on and off turning off the display (recommended on a forum I found)
  • Uninstall Virtualbox (suggested on another forum I found)
  • And I tried all the drivers I could find for my card without result

  If it helps any, I am running Windows 7 Home Premium on my Dell Stdio XPS 1645.

  My guess is that even if the wireless card is said (in addition to one!) not to turn off or sleep, she does it anyway. Is there another solution I'm missing somewhere?

  I've had this problem for months now, it becomes more frustrating. I would really like to avoid putting fresh with a new installation of Windows... Any suggestions?

  Thank you!

  -Jackson

  Hello

  Very nice work to try to turn it on.

  -------------------------------

  A general comment .

  We all have a general problem. There are several 3rd party applications installed and used the insert themselves in the Windows network components, some of them also modify the default configuration. Most of these applications is not thoroughly test. They are tested to work, but usually it's on a certain simple standard system. He has not tested, and take into account hundreds of iteration of network configurations of end users with a wide variety of material and other related network applications.

  These applications include 3rd-party security costumes, managers of networks, 3rd part of the network of assistants, virtual applications, users to play with the settings found on the Internet with limited info on what they actually do, and many others.

  To complicate the problem, some of these applications load at startup process and interfere with the network, even if the application is disabled, or and uninstalled.

  I found rather known 3rd party networked application that allows to leave about 100 entries in the registry and a Undelete-able desktop the icon, after that it is uninstalled.

  As long as it is sad, because sometimes it is the only functional solution is re - install the operating system on board back to the standard State.

  -------------------------

  Regarding energy saving, there could be more settings.

  Look at the BIOS of the laptop too, some of them have on-board hardware system.

  Also look at the start and the process to ensure that there is no use of 3rd party involved in managing WIFI.

  This can help to discover.

  Start & Process Explorer - http://www.ezlan.net/infestation.html#startup

  ------------------------

  Assuming that the signal is strong, and that there is no noise in the electrical environment.

  Visit the support site of the computer and make sure that you use the latest drivers * for network adapters.

  Check support for the router and make sure that your using the latest firmware for the router.

  Uncheck the box to the NIC of energy economy (I.e., do not leave the card save energy).

  There may be some variations on where is the energy saving setting.

  Here are a few examples, YMMV, look around your systems.

  Example, http://www.ezlan.net/example/powersave.jpg

  Example, http://www.ezlan.net/Win7/power_sav_wireless..jpg

  Example, http://www.ezlan.net/Win7/power_save_win7.jpg

  Example, http://www.ezlan.net/Win7/adv_power-sav.jpg

  * On drivers update .

  Try installing the latest drivers from the card manufacturer support page.

  Download the drivers and extract them to a folder of your choice.

  In Device Manager, right-click on the adapter.

  Click Update drivers and choose her browse my computer for drivers.

  Choose let me a list of choices, click on disk and point to the folder with the drivers.

  ----------------------------

  When you are with what you have done is launching the present.

  WinSock and TCP/IP update.

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  Do the same process to refresh the TCP/IP just replace the command typed with.
  
  netsh interface ipv4 reset press enter
  
  netsh interface ipv6 reset press enter
  
  ipconfig/flushdns press enter

  Restart your computer.

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• MacBook Pro (mid-2012) is very slow. EtreCheck said not enough RAM but Activity Monitor says RAM is fine.

  It happens about any application (especially chromium, but also iMovie, TextEdit, Messenger, Finder, etc.). It will work correctly for 30-60 seconds give the rotation for 30 seconds beach ball, then works again then beach ball.

  EtreCheck version: 3.0.3 (307)

  Report generated 2016-09-15 20:31:59

  Download EtreCheck from https://etrecheck.com

  Duration 76:03

  Performance: Poor

  Click the [Support] links to help with non-Apple products.

  Click [details] for more information on this line.

  Problem: Beachballing

  Hardware Information: ⓘ

  MacBook Pro (13-inch, mid-2012)

  [Data sheet] - [User Guide] - [warranty & Service]

  MacBook Pro - model: MacBookPro9, 2

  1 2.5 GHz Intel Core i5 CPU: 2 strands

  4 GB of RAM expandable - [Instructions]

  BANK 0/DIMM0

  OK 2 GB DDR3 1600 MHz

  BANK 1/DIMM0

  OK 2 GB DDR3 1600 MHz

  Bluetooth: Good - transfer/Airdrop2 taken in charge

  Wireless: en1: 802.11 a/b/g/n

  Battery: Health = Normal - Cycle count = 1091

  Video information: ⓘ

  Graphics Intel HD 4000

  Color LCD 1280 x 800

  Software: ⓘ

  OS X El Capitan 10.11.6 (15-1004) - time since started: about 2 days

  Disc information: ⓘ

  TOSHIBA MK5065GSXF disk0: (500,11 GB) (rotation)

  EFI (disk0s1) < not mounted >: 210 MB

  Macintosh HD (disk0s2) /: 499,25 (Go 421,85 free)

  Recovery HD (disk0s3) < not mounted > [recovery]: 650 MB

  HL-DT-ST DVD - RW GS31N disk1: (8.42 GB))

  USB information: ⓘ

  Apple Inc. FaceTime HD camera (built-in)

  Apple Inc. Apple keyboard / Trackpad

  Computer, Inc. Apple IR receiver.

  Apple Inc. BRCM20702 hub.

  Apple Inc. Bluetooth USB host controller.

  Lightning information: ⓘ

  Apple Inc. Thunderbolt_bus.

  Guardian: ⓘ

  Mac App Store and identified developers

  Kernel extensions: ⓘ

  / Library/Extensions

  com [loading]. Apowersoft.driver.AudioDevice (1.6.7 - SDK 10.11 - 2016-09-13) [Support]

  Launch system officers: ⓘ

  [no charge] 7 tasks Apple

  tasks of Apple 155 [loading]

  tasks of Apple 68 [performance]

  [killed] 8 tasks of Apple

  8 killed process lack of RAM

  Launch system demons: ⓘ

  [no charge] 48 Apple jobs

  [loading] 158 jobs Apple

  [running] Apple 73 jobs

  [killed] 12 tasks of Apple

  12 killed process lack of RAM

  User launch officers: ⓘ

  [loading] com.google.keystone.agent.plist (2016-07-11) [Support]

  Plug-ins Internet: ⓘ

  Default browser: 601 - SDK 10.11 (2016-07-18)

  QuickTime Plugin: 7.7.3 (2016-07-18)

  3rd party preference panes: ⓘ

  None

  Time Machine: ⓘ

  Time Machine not configured!

  Top of page process CPU: ⓘ

  top of 7%

  iMovie 3%

  1% kernel_task

  1% Google Chrome

  0% Dropbox

  Top of page process of memory: ⓘ

  1.30 GB Google Chrome Helper (13)

  516 MB kernel_task

  IMovie 193 MB

  Google Chrome 172MO

  Mdworker (9) 123 MB

  Virtual memory information: ⓘ

  33 MB free RAM

  3.96 GB used RAM (741 MB cache)

  4 MB Swap used

  Diagnostic information: ⓘ

  13 September 2016, 23:12 self test - passed

  13 sep 2016, ~/Library/Logs/DiagnosticReports/suggestd_2016-09-13-211853_[redacted].crash 21:18:53

  /System/Library/PrivateFrameworks/CoreSuggestions.Framework/versions/A/support/ suggestd

  What do you see in the activity monitor to suggest that the RAM is fine?

  The EtreCheck report shows that you have only 33MB of free RAM in time, which can only cause slowdowns. Google Chrome only takes 1.3 GB of it. Chrome is a Devourer of enormous resources, so if possible, try to quit smoking by using another browser.

• MacBook Pro SSD 7.1 more slow speed 200 MB

  Hey,.

  I bought an SSD of Sandisk and 480 GB (http://www.amazon.de/SanDisk-Plus-480GB-Interne-schwarz/dp/B018X8LB2G) with a speed of 480 MB/s reading and writing speed of 400 Mbps. I compared with Blackmagic Disk Speed Test and the result seems to be horrible. Speed of 250 MB/s read and 180 MB/s write speed.

  The Macbook Pro 7.1 is not compatible with these speeds or I do something wrong? Would be happy for any response.

  See you soon

  

• OfficeJet Pro 8600, Windows XP, very slow to print scanned pdf

  All other prints exception scanned to PDF print normal PCDFS, even imported e-mail, etc., all other types of files.

  Problem occurred after problems with XP, computer tech could rectify not so copied all files and reinstalled XP, no problem with XP, but the printing problem now with my own scanned pdf.  Thanks for any help.  JLS1946

  Thank you to all who responded.  I have to admit it's a tough trying to decide it's the printer, it's Adobe, is the USB connection / wireless?  Now, that's what I managed to rule out now (thanks for all the help that JLS1946 did) it's not the connection.  I went until take that to someone who is very familiar with the Adobe and they suggested uninstall/re-installing Adobe. He said you should not lose your saved work and which corrected this before.  However, not all of you use the same software or the print version. PDF files, it seems.

  Knowing what I know about the way in which the information is transferred to the printer, it is meaningless for me how only a few .pdfs are slower than others.  Check the contents in the file you are trying to print and compress, when you can.   I know that the web content may take longer to process during a print job and now I have to wonder if that has no place in the commonality among all of those here.

  I think the last document I ran through should have some good suggestions. Let me know if it works. One of the reasons I don't think specifically that it is the Officejet 8600 is especially because it happens to other printers like this.  The only thing you have in common is Adobe. While searching for other PDF readers, I have noticed Adobe had so many stars (3.5 stars) like Foxit Reader (4 stars) did.  I'm not the right person to defend as to who can be a better software to use however.  I know I like CNET for their reviews and videos.