newbie JDeveloper Setup question

Similar Questions

• newbie Y560P laptop questions

  Lenovo forums are very informative and I looked for answers to my questions and have found some but not all. I recently (St Patty's day) ordered an ideapad y560P. I should have asked these questions before buying but there was an e-coupon deal that ends the day of St patty, I had wanted a laptop pretty advanced for a while so I jumped. Life is not perfect!

  1. a clean install of windows is possible with recovery disks that Lenovo provides? If this is not the case, what is the best way to do it?

  2. the Y560P can fully utilyze the new SATA 3 SSD as boot drive? Void the warranty?

  3. wait for Lenovo to ship my laptop until the Sandy Bridge sata port questions/reminder are developed?

  4. someone here successfully using imaging software (like Acronis true image} on their laptops?)

  Sorry for the newbie questions. I built my own desktops for years, but this will be my first laptop. Time passes! Thanks in advance for any help.

  Hey, I'll do my best to respond to these:

  (1) actually, no discs are technically provided by Lenovo. Your system comes with a separate, partition that contains a recovery image. That being said, you can create a set of recovery disks by running their usefulness (comes pre-installed). When you use these disks, it basically as a duplication process. So yes, you can do a clean install, if you think it their image pre-built a clean installation

  (2) not sure about the 3 SATA drives, but drives does not cancel your comprehensive guarantee. I would always keep the original drive where the system needs to be sent, but I think that the RAM and CPU are considered as 'evolutionary customer options' and are therefore not guarantee-killers.

  (3) from what I've read, Lenovo has already stopped the lines with questions of Sandy Bridge. None of these units should be delivery to consumers. If I remember correctly, it only affected some of the i7 lines. If you have concerns, you can always call Lenovo with your serial number, and they can check if the unit is affected. However, Lenovo has been very quick to fix this, I just couldn't see their shipping defective units known to customers.

  (4) Acronis and Ghost work quite well, assuming it is a standard drive. I could not find any problems with people using either a product on the readers of the so-called "hybrid".

  Hope that helps a bit!

• CVP newbie on routing questions

  Hello, newbie here in CVP. Got a deployment with UCCE/CVP 9 X and Conn CUCM/Unit 9 X. No Sip Proxy and the current context we have to route calls to CUCM prior routing to ICM/CVP. I know that's not the best Setup, but there is no budget to spend more managers to call for UnityC to CIM at this stage so all calls will be pretty closely from before CUCM hit ICM. That said, I'm getting conflicting information about how to configure routing. Probably more too read things. From my tests, I need 2 PIMS on every PG to cover both CVP servers which means I need 2 labels VRU to account for each customer routing of the CVP (ie. 121212 and 131313)? I have heard however I need one but my call routing will fail if it is not 2. Is this correct? If this is the case, how ICM knows what CVP VRU label to use when a call is initiated of CUCM to ICM? And how is that redundant PVC without proxy SIP or DNS Srv? Any recommendations would be greatly appreciated.

  No, you build the same label for all customers of routing CVP.

  Sent by Cisco Support technique iPhone App

• JDeveloper setup package is corrupt?

  I downloaded the JDeveloper for Windows Installer "Oracle JDeveloper 12 c 12.2.1.0.0 (2.1 GB) Windows" (folder 1). "

  When I run the Setup, somewhere around 80% of the loading procedure, I get a fatal warning indicating that the package is corrupt "error nr 1.

  I tried to download with multiple browsers on multiple platforms and tried to install it on multiple platforms... always the same error.

  Is it just me, or is the actually corrupted file?

  Download page:

  http://www.Oracle.com/technetwork/developer-tools/jdev/downloads/index.html

  I test and it worked on my win 7 x 64 pc.

  Timo

• JDeveloper ide question - attributes sorted 12 c

  Hi all

  This may seem like a stupid question, but how do I cancel the sorting of attributes to a display object or an entity objects?

  Thank you

  After following file .jdeveloper for the changed files and playing with the sorting, I found that the files that change when you sort the attributes or change the column width in the IDE.

  .. /system12.1.3.0.41.140521.1008/o.BC4J/jboVoAttrColumn.properties

  and

  .. /system12.1.3.0.41.140521.1008/o.BC4J/jboVoAttrColumn.properties

  You can change the value first after the sign '=' to 'NAME' to .

  Alternatively, you can delete the two files and do with it!

• newbie triggered custom question

  Hi gurus of Labview:

  It could be a very simple question for you guys, please provide some tips.

  Here's my scenario measure: I need monitor output of the sensor which is a signal voltage (to AI0), I just need to get the voltage reading when I get a trigger signal to axis to another (PFI0). I would like to save to a file .txt with the news. on the value of the voltage and the time stamp of each measure. With a simple while loop and the DAQ assistant, I can get the measure to start when a trigger is detected on the PFI0, however, the measure will now continue to operate after that. Instead, I want the system to measure a voltage value, then wait for the next trigger signal. I'm pretty new to labview, so it will be very appreciated if someone can point me in the right direction.

  Thank you very much.

  Shao

  OK, after reading this link given above about 1 sample (timed HW) I think that what you really want is continuous samples with the sample on your external clock clock.

  Apparently there is no buffer with the 1SHWT (I'm short hand here).  If you miss one, you get the overflow error.  That tells me your loop is medium to slow or your pendulum goes faster than you think.  By going with continuous samples, you will not have to worry about this.  You can simply take as much data as you want and save the heap in the file.  This will make things work a little easier.

• Newbie BB development question

  Hello eveyone. I hope this is the right place to post this question, but I'm looking for advice. I'm new to the development for BB, but since 3 days I did a lot of reading. The only problem with this is that the more I read more confused I get. I have developed solutions ASP.NET, but never anything like that for mobile devices.

  Here are my thoughts on what I would do:

  -Create a Web page for the BB, which goes to a SQL Server, accessing a view and extracts the data in a data Repeater or a gridview for viewing.

  I have an IIS server running locally and can be viewed on BlackBerry now. I've set up and you can check out. WML and. Pages HTML to it very well.

  My question is this. I read about this plug-in for Visual Studio 2008. I downloaded and installed successfully.

  I do not know the following:

  -Can I do what I would do without BES?

  -What would be the best way to go about this? A few suggestions on what would be the best way to approach this project.

  Any guidance would be greatly appreciated.

  Thanks in advance,

  Bob

  psu99 wrote:

  So I can just use Visual Studio.net 2008 and create a sample page. I use the PlugIn which can be downloaded or can I just without programming?

  From what you say, you just need Notepad, vim, emacs, any other to design a Web page. The fact that You ' l browse this page with a Blackberry or an iPhone or a Samsung is on top of that.

  psu99 wrote:

  And what you say to me that I didn't need BES... my point of view on what it was only used for PUSH applications.

  You use a BES is required if the Web server is not reachable from outside your corporate network. In this case, you need BES just for its web proxy that will allow your browser to reach a machine inside the LAN. BES can also be used for automatic authentication issues based on the PIN code of your device and/or X.509 private keys that can be installed by the IT company.

• SG300 Setup question

  Hi and thanks for reading.

  I have 3 sg300 switch/routers, I'm trying to set up and I have a few questions. This is how I have it set up so far.

  SG300 #1 mode layer 3 (router) with spf ge27 connected to our switch through fibers. have set up 2 VLANS (vlan1 10.10.0.1 device ip value) contains all the unidentified ports. (vlan200 ip 172.30.0.30 the value contains the ge27 port). our main hp curve pro is 172.30.0.1.

  second sg300 #2 (layer switch mode 2) a fiber connecting port 10 to 28 of the first sg300 port. This one has 1 vlan with ip defined on 10.10.0.3

  third sg300 #3 (layer switch mode 2) a fibre port connected to the port the second sg300 also with 1 9 vlan, ip device set to 10.10.0.4.

  After you add the declarations of good road to the first device I can ping to all remote subnets and receive answers from one of the devices. everything seems to be working but having a weird problem. I can't device managed on the basis of 2 or 3 (interface) web from anywhere that directly connected to one of the 3 devices. I can handle the device one from anywhere.

  Not sure if it's the correct configuration or what Miss me to be honest.

  Thank you

  On the 2 switch, the switch must have a default gateway specified in order to manage from a different subnet.

  -Tom
  Please evaluate the useful messages

• WLC 5508 w / 1042-initial Setup Question

  I have to do an installation from scratch and was looking for some suggestions as a basis for the configuration. I have a 5508 I have to belay 6509.

  I have to get up 16-1042 model APs.  I will support many customers - scanners of bar codes, phones, iphones and laptops with WPA2.  I have to create 2 local networks without wire - one for DATA and for a hotspot.

  Does anyone have a basic configuration that they can share for both the WLC and 6509 configuration?  Someone at - it a 'from' scratch version doc process they could share?  Someone at - it a version of code recommended?

  I downloaded the 7.0 Configuration Guide but was hoping to get some guideance real world also.

  TIA,

  Amir

  Hello

  Well, from version 7.0, is the last it is good to start from it.

  First implementation of 5508:

  http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mint.html.

  I advise you to read carefully this section which explains the details and best practices to configure WLCs ports and interfaces.

  Regarding the config guides, I advise you to go through the design guide:

  http://www.cisco.com/application/pdf/en/us/guest/netsol/ns279/c649/ccmigration_09186a00808d9330.pdf.

  And examples of configuration:

  http://www.cisco.com/en/US/products/ps6366/prod_configuration_examples_list.html.

  They are valid for all WLC models.

  They are based on the configuration and very good examples.

  HTH,

  Tiago

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• BlackBerry Smartphones Newbie with 2 questions, need help.

  Hi guys,.

  hope you can help. I recently bought a BB Curve and think it's great.

  However the LED stopped working. I turned off the unit and removed the battery. When I put it in the LED lights up red, so it must work. I checked my profile settings and all say that the LED must be on. I have changed this setting to disabled, backed up, and then put it back on and saved and still no action led.

  The second question is attachments on my emails. I can't open attachments, photos, documents spreadsheets nothing. I use desktop re-Director. Is it possible to have attachments that are sent using this unit or any other bits of software? I have the only BB at work so I'm not so sure, establishment of a BB server is viable.

  Your opinion would be greatly appreciated.

  There is not all the configuration parameters for the Service of the attachment. The following table describes the supported types of attachments on a BlackBerry

  http://www.BlackBerry.com/BTSC/KB03265

  By default the LED flashes green to indicate that you are in a wireless coverage area. I found it annoying and disabled. Check the setting under Options | Screen/keyboard and turn the LED coverage indicator inactive.

• 11.1.1.7.0 jdeveloper Setup error

  Hi h install jdeveloper 11.1.1.7.0 in my 32-bit Windows 7, I get this error

  

  It installs in the C:\oracle\Middleware directory in this directory, I have already install weblogic 10.3.6

  I am trying to install the runtime in the same directory, but still get the error above, what could be the problem

  

  feel free to use jdev 11.1.1.9. This version is aligned with the rest of Fusion Middleware 11.1.1.9 including extensions of SOA, WebCenter and BI:

  https://blogs.Oracle.com/jdeveloperpm/entry/oracle_jdeveloper_and_adf_11

  • Oracle JDeveloper and ADF 11 g Release 1 (11.1.1.9.0), is Oracle Fusion Middleware 11.1.1.9.0 and Oracle WebLogic 10.3.6:

  http://www.Oracle.com/technetwork/developer-tools/jdev/index-091111.html

• jDeveloper debugging question

  Hello

  I'm new to the development of the OFA and am under jdeveloper 10.1.3.3.0 for development. I have managed to download code from the server on my local and successful machine to launch the application from my office as well (loan application). I want to know how to enable application logging or debugging functionality so that when I run the application, I can see the activity on the jdeveloper console? In one of the site he talks about changing the project properties (Configuration-> development-> Runner) and add a parameter - dbjo debuggeroutput = consile. However, in the current version of jdeveloper, I don't see this option at all.

  Can some please provide some guidance?

  Thank you

  Hello

  See this link:

  Apps - OA Framework - 7 different Debugging Techniques

  Sushant-

• Setting up the environment of Applications Dev fusion Jdeveloper - version questions

  I am facing problems regarding the versions of installed packages.
  
  https://blogs.Oracle.com/fadevrel/entry/jdeveloper_and_fusion_applications_explained
  
  The post was very useful. But the expansion of fusion development pack causes problems of version.
  I installed 11.1.1.6.2 Jdeveloper on 32-bit Windows computer. I installed the packages, but four packages are in trouble.
  One of the package is not installed because the minimum version required for oracle.ide (package) is 11.1.1.6.62.98 and existing is 11.1.1.0.11022.xxxxx(I j'ai oublié le nombre). How to get around these problems of version. Unless I have install the fa_dev_bundle.zip, I can't have a role of Fusion application customizations and extensions, right?
  
  To summarize, there are some issues with the versions. Versions are earlier than necessary or there is any required version. How to solve this?
  
  I would be happy if you can point to an another forum/page/documentation that can help me find a solution.
  --
  Harsha

  Harsha049 wrote:
  I would be happy if you can point to an another forum/page/documentation that can help me find a solution.

  Harsha,

  I'm glad you found my blog useful. Have you seen the second part that I just posted a few days ago by chance?

  https://blogs.Oracle.com/fadevrel/entry/jdeveloper_and_fusion_applications_explained1

  It covers installation of all extensions and configuration of the built-in WLS field.

  I hope this helps.

  Oliver
  Fusion applications Developer Relations
  http://blogs.Oracle.com/fadevrel

• Newbie on MemoryStick question

  I am to evaluate vm workstation for our company and have no real experience with vm workstation.

  I'm hosting on windows 7. I created a machine virtual windows XP without any problem at all. Here is the question, when I'm on windows xp and I insert a USB / flash drive, virtual machine software allows me to connect to it and it displays in the status bar, but I can't see or access in the my computer window.  I really need to be able to copy files from the drive flash on windows xp machine... I read everything I could find, and it seems to me it should work... Sorry if this is a stupid question, but can someone tell me what I'm missing?  Thanks for your help!

  Welcome to the forums!  Do you have the VMware Tools installed in the virtual Windows XP machine?  You should be able to drag-and - drop between your Windows 7 host machine and the virtual machine.  You can disable the removable device (USB key) in the virtual machine to the host o/s.  You should then be able to open the drive, and then drag and drop the files / folders to your Windows XP VM.

  Please keep us informed.

  Good luck... Bruce

• Newbie on permission question

  Hello

  I have an operational 5.0.1 AMS. But I'm a newbie to AMS.

  I want to implement the authorization features for the AMS for streaming (vod) saved mp4 files.

  In a first time, for clients Flash using the RTMP protocol, subsequently for iOS/Android devices using HLS/HDS.

  My plan is that the client sends one identifier internal video to flow and a session id.

  These two parameters should be passed to AMS to another remote server with a PHP API or a SOAP web service. This remote server checks if the video might be listened to (Simplified) and returns true or false to the AMS.

  Now, my problem is that I have no idea where to connect to the communication between the client and the server.

  So far I got the normal way to proceed would be to listen to certain events in the main.asc.

  All the examples I found to date only show how to manage application.onConnect.

  But I would like the AMS to react on the command of NetStream.play (), sent by the Flash client.

  How is that possible?

  And, is it possible to do for HLS streaming that does not rely on Flash clients?

  Thank you very much in advance

  Hyper

  You pass additional arguments to the connect function:

  NC. Connect ("rtmp://myserver.com/test", "12345", "abcdefgh");

  On the media server, definition of the function onConnect to take as many arguments as you expect:

  application.onConnect = function (client, videoID, sessionID) {}

  your code to manage the client connection here, probably to check the values to the remote server

  }

  The customer is always present. You can add additional arguments after her.

  http://help.Adobe.com/en_US/flashmediaserver/ssaslr/WS5b3ccc516d4fbf351e63e3d11a11afc95e-7 edfSSASLR.html #WS5b3ccc516d4fbf351e63e3d11a11afc95e-7fe1SSASLR

  You need to pass arguments in the same order as the onConnect function.