No Internet access on wireless network

Similar Questions

• I can't connect to the Internet via the wireless network. It shows that I have local access only. I can't connect even in SafeMode with network.

  I can't connect to the Internet via the wireless network. It shows that I have local access only. I can't connect even in SafeMode with network.  I have Ping www.microsoft.com and the answer is "ping request could not find host www.microsoft.com.  I am connected to the network wireless through my iPad and can connect via my smartphone. This leads me to believe there is only something configured properly on my laptop. Can anyone provide assistance?

  Hello

  You can try a system restore...

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  .. .choose time, until this problem (you may tick to show more older restore points).

  Tricky

• Problems connecting to the internet using the wireless network connection

  I can't connect to the internet using my wireless network connection. I had made the diagnosis and he stated that "the DHCP is not enabled for the wireless network connection. I had checked the DHCP, but it has been activated!... Someone would give any suggestion for me to solve the problem?

  Open the run command box by pressing Windows key + R, type services.msc and press enter . Search The Client DHCP and check if it is enabled or disabled. If disabled then turn it on and see if the problem still persists or not.

  Open the run command box by pressing Windows key + R, type cmd , and press enter . At the command prompt, type ipconfig/all and press ENTER. Now, check the IP address, default gateway, DNS etc. If you find all the information is correct, but you cannot yet access the Internet so if you connect the wireless network is secure or not. To determine the glance to the wireless network icon in the taskbar, then click on it. It will show you the available wireless networks. If there is a "yellow shield" present on the network icon, the network is not guaranteed, if there is no "yellow shield" does while the network is secure. In a secure network, you might have a "network security key. In this case try to disable the 'Network security key' option for this network. To do this:

  Open Control Panel , click network and Internet , click network and sharing Center , click manage wireless networks on the left.

  In the list select the wireless network and do a right click, select Properties, Security disable tab all options that is, in security type do not select no authentication (Open) and to the type of encryption , select none . You can also activate the automatic connection and SSID settings to further enhance connectivity, on the connection tab, click to select the "connect automatically if this network is in range " and "check boxesto connect even if the network is broadcasting his name (SSID) .

  For more information click here and see how you can determine whether a network is secure or not.

  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-know-if-a-wireless-network-is-secure

  If the problem still persists, then check your firewall settings and make sure that the firewall is not blocking your Internet connection. Some software Antivirus has a built-in firewall and they block by default all unknown connection to the tightening of security.

  Try to restore Windows Firewall default settings. Open Control Panel click on network and Internet , click system and security , click Windows Firewall , click default settings .

  Hope this will help. Thank you.

  Arup Ratan Paul

• Cisco linksys router and cannot access the wireless network

  We have cisco linksys wireless router.  When we installed everything first, we could connect our wireless laptops to the network.  Now, however, the network is detected, but there is no access to the internet.  We have even a guy from ATT were out and he said that the wireless router has been installed backwards?  He installed a dsl fast access on our laptop icon, and now we can access the wireless network but only if we connect as the first.  We can also connect iPod to the wireless network.  They detect the network, but when we enter the password cannot connect.

  Hi JC_3094,

  Welcome to the Microsoft Community and thanks for posting the question.

  According to the description, it looks like you aren't able to access the Internet.

  The likely causes of this problem is if the router is not configured properly.

  Here are some steps that should help you to solve this problem.

  Method 1:

  Check if the router is configured properly to get access to the Internet.

  Method 2:

  Try the steps mentioned in this link and check:

  This tutorial is designed to help you identify and solve problems with a wired (Ethernet) and wireless (Wi - Fi) network connections in Windows.

  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

   

  Method 3:

   

  If there is a frequent disconnection try to update the firmware on the router and check.

   

  In addition, visit these links for more information:

   

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

   

  Hope this information helps. Respond us if you have any questions with windows and we will be happy to help.

• Password to access the wireless network

  I am trying to set up my iPhone to my home wireless network and I don't remember the password to access the wireless network and it drives me crazy! I'm going to network and sharing Center, then the properties of the wireless network. I click on the security is WPA-personal security type, is type of encryption: TKIP the box to show the network security key characters will not let me click on it. Anyone have an idea how I can access my own password?

  Thanks a lot, a lot in advance! Lisa

  Keep passwords secure - Microsoft on passwords strategy
  http://support.Microsoft.com/kb/189126

  Contact support on the router's Web site people. Or reset the default router and start over.

• I'm trying to access a wireless network with the password provided for me. I get the following error message

  I'm trying to access a wireless network with the password provided for me. I get the following error message: "the network password needs to be 40bits or 104bits depending on your network configuration. This can be entered as 5 or 13 characters ascii or hexadecimal 10 or 26. "what does this error message mean and how do I address so that I can access the wireless network?

  I use XP Professional with service pack 3. I get this error message every other time I try to log in to a protected wireless network security. I used to not get this message; but, now, it may be impossible, sometimes to call all wireless providers when I might only need for a short period or after hours service opening.

  In addition, it is my computer that requires the network password to be different, not the provider of wireless. A password is given to me who works for other users, but my computer won't let me use it.

  Hello

  I suggest you to visit these links and check if it helps:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-networking/the-network-password-needs-to-be-40-bits-or-104/f3fdc3ee-CB40-4107-A632-082093dcdcb8

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-networking/need-to-connect-to-home-wireless-network-Windows/5bf37a22-cc42-4a0f-9d15-83e780f00123

  It will be useful.

• where can I find the security code to access my wireless network

  security key

  where can I find the security code to access my wireless network.

  Hello

  Check with the manufacturer of the router's support and most have forums and excellent documentation online.
  You should be able to access the router to set a new SSID and password if necessary.

  You must know the SSID (name of the router) and the password.

  If you do not know these you can find in the running on the WiFi system now with this
  free tool. This is not a crack, it should be run on a local computer that has access (or access)
  to your router. Sure, the information will not be there if Windows was reinstalled or information
  has been deleted otherwise.

  -FREE - WirelessKeyView recovers all the wireless network security keys/passwords (WEP/WPA) stored
  in your computer by the service 'Wireless Zero Configuration' of Windows XP and by the 'autoconfiguration WLAN service.
  service of Windows Vista. It allows you to easily save all keys to text/html/XML, or copy a single key to the
  Clipboard. (Works on XP, Vista or Windows 7).
  http://www.NirSoft.NET/utils/wireless_key.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• How to get two laptops to access the wireless network.

  My chip wireless on a Dell Inspiron 1520 laptop (intel pro wireless 3954bg) can find the wireless network if I use Intel Pro software, but Windows cannot find the wireless network. My real growth problem trying to connect a second computer; an IBM T42 think Pad computer to the wireless network, but I get a message that the network is secure, and the second computer keeps trying to acquire an address, but will not acquire an address. He just continues to try to acquire again and again, he can never acquire it. This second computer using Windows to configure the Wi - Fi connection and was working fine until I tried to connect the Dell laptop upward. Then, the IBM laptop cannot acquire an address. I go around and try to understand it. Someone at - it information to solve this problem? Both computers are runing Windows XP Pro SP3. My wireless router is a Belkin54g (F5D7230-4V8000)

  Thanks for any help,

  Btk (billy the kid)

  You can control a with either wireless network adapter software integrated in Windows XP (or WZC Wireless Zero Configuration) or with software provided by the manufacturer of the card (for example, Intel PROSet/Wireless), but not both at the same time.

  Most, but not all, software configuration wireless no Windows is smart enough to disable WZC automatically.

  There are a few sites that offer "safety tips" for wireless networks which includes 'hide' your wireless network by disabling the SSID broadcast.  This is not a good idea and does not, in fact, your wireless security.  See http://blogs.technet.com/b/steriley/archive/2007/10/16/myth-vs-reality-wireless-ssids.aspx if you have disabled broadcast SSID of your router, automatic configuration won't be able to find it.

  I get a message that the network is secure, and the second computer guard trying to acquire an address, but will not acquire an address

  If you have enabled encryption wireless router (a very good idea), you will need to enter the correct password in order to connect a find an IP address. What type of wireless encryption configured on the router?

  This second computer using Windows to configure the Wi - Fi connection and was working fine until I tried to connect the Dell laptop upward. Then the IBM laptop cannot acquire an address.

  You have changed something else.  The idea of a wireless network is to allow multiple computers to connect; connection to a computer shouldn't affect how another computer connects.

  The easiest way is to configure your router to connect a computer using an Ethernet cable (if you connect wireless, you will be disconnected when you make a change to the configuration of the router wireless).  For the Belkin router User Guide is here--> http://cache-www.belkin.com/support/dl/p74559-f_f5d7230-4v8xxx_manual.pdf

  Open a web browser (Internet Explorer, Firefox, etc.) and type 192.168.2.1 in the address box.  You should get to the home page of the router. Click on the "Login" link at the top.  The default password for the router is blank (no password) unless you changed it.

  Click on the link "Channel and SSID" under the heading "wireless" on the left side of the page.

  • Make sure that there is to check the "Broadcast SSID"
  • "Wireless mode" should be "g only" or "fashion g and b" (the latter is necessary only if you have a very old b wireless adapter in one of your computers)
  • I suggest you let off QoS (but click on "more info" or see what says the User Guide)
  • The wireless channel should be 1, 6 or 11.  If you have no difficulties, let him you will find
  • "Protected mode" should be off (but click on "more info" or see what says the User Guide)
  • If you make changes, click on "Apply Changes".

  Click on the 'Security' line under the heading "wireless".  You should be able to see both what type (if any) encryption is configured (64-bit WEP, 128-bit WEP, WPA, or WPA2) and the password (if any).  Unless your computer maps are old, you should use WPA2.  If the adapter in one or more of your computers is too old to be capable of WPA2, use WPA.  Regardless of the bit, WEP length, is easily broken.

• Unable to connect to the internet through the wireless network

  original title: this computer does not have an installed and configured wireless network adapter

  Hello, about a week ago I just reformatted my Windows vista computer, and now I do not have a wireless network and I cannot connect to the internet, I use another computer to do this, and only the network card I have is Marvell Yukon 8888036 PCI - E Fast ethernet controller. Please help I really wanet to go on the intrnet. My computer is mobile intel r 945gm express chipset controller 0 microsoft corporation wddm

  Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > looking for Vista drivers newer network adapters/etc > download/install the.

  The computer you are using now if you have an Internet connection with the other > download / save drivers > copy them into Flash Drive > transfer / install on another computer/laptop.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

  Troubleshoot network adapter problems to Microsoft link above.

  See you soon.

  Mick Murphy - Microsoft partner

• connect to the internet by two wireless network adapters

  How can I configure the two wireless network adapters for both wi fi access points in a pc?

  Hi Myo,

  Thanks for posting your query in the Microsoft community!

  I'm sorry to inform you that, two wireless network adapters for two computer Wifi access points is not possible.

  From the second connection will connect to the network, one gets automatically disconnected.

  Please mail us if you have any other questions, and we will be happy to help you.

• Windows 7 starter, no internet access, WPA2 Enterprise Network

  I use an Asus EeePC for the first time to work.  I replace my ibook apple that I had no problem with in the past. I entered the correct name for the network.  has selected WPA2-Enterprise, AES encriptación.  Using the PEAP authentication.  After entering my user domain\username and password, I connect to the network, but when I look at the network he says no internet access.  I can see my internal network and the computers.

  Any advice would be greatly appreciated.

  Thank you

  Hi Kbpipes,

  First check the edition of Windows 7 installed on your computer, since you mentioned that you use the Windows 7 starter edition. Windows 7 starter edition will not be able to join the domain network. To join the domain network, you will need to install either Windows 7 Professional, ultimate edition.

  Access the link below to learn more about the field of Assembly.

  http://Windows.Microsoft.com/en-us/Windows7/products/features/domain-join

  To verify which edition of Windows 7 is installed on your computer, follow the steps below.

  1. Click Start.
  2. Right-click on computer and click Properties.
  3. Check the information on your computer.

  However, you try to run the troubleshooter from network built into windows 7 and check if it can help solve you the problem of connection to the Internet.

  Access the link below and follow the steps.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  You can also try to temporarily disable the security software of the computer and try to connect to the Internet. If you are able to connect to the Internet, you can contact the manufacturer of security software and check if you need to change the settings. Later, re-enable the security software.

  Also, you can try to start the computer in safe mode with network and check if you can connect to the Internet. To boot to the desktop in safe mode with network keep tapping key F8 during restart. Once you see the option to start it in safe mode with select network and press ENTER.

  Access the link to learn more about how to start the computer in safe mode: http://windows.microsoft.com/en-US/windows7/Start-your-computer-in-safe-mode

  You can also contact your network administrator and check if there are settings that must be changed or configured to access the Internet.

  Post back with the above information and let us know the result.

  Thank you and best regards,

  Srinivas R Microsoft support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Connect to the Internet through a wireless network connection

  I've just set up a new router/modem to Qwest (C1000A) and I have a problem of wireless internet connection on my laptop.  I have a Mini Dell PCI card 1390.  The laptop shows that I have excellent wireless connectivity.  Is there a setting I need to change to get my internet to stay connected? Thank you.

  Kris,

  This tweak, you should be able to do...

  Start, Control Panel, Manager of devices. Click Network and then right click on your wireless network adapter, on the left, click on properties, power management. Uncheck the allow the computer to turn off this device to save power.

  Try running WinSock XP Fix

  Also try...

  How can I disable wireless configuration and enable Windows XP Wireless Auto Configuration services

  Rick

• Satellite Pro L510 cannot access my wireless network

  The laptop recognizes wireless networks are available but requires a 'logon domain' with my user name and password.
  Where can I find the logon domain? What is it?

  Hi mate

  I don't know how you are trying to connect to the WLAN, but generally you n t need no user to connect to the WLan router password.

  You need, it's the right SSID (wireless network name), Wlan encryption right and good WiFi encryption password.

  First of all, ensuring that the WiFi network has been successfully activated!
  Key combination to select Wlan using FN + F8!
  Also read the manual of use of laptops for more details how to enable the Wlan!

  Then, you must configure the Wlan router every router supports a configuration different procedure but normally you should always have a manual with your router.
  There should be a step by step instruction how configure it!

• WRT54G Setup for internet access using Lacie Network Space Max

  Help, please!

  I tried for the past 2 weeks, try to configure my WRT54G Router, so it allows me to access the Lacie on the internet without success. I followed all the instructions of Lacie and all other FAQ and help on the internet, still no luck. I spent several days with Lacie tech support and they could not understand it - why my router would allow me access via internet. I hope that the big guns here can help me.

  I have a number of laptops connected to my local network and all wireless laptop can access the NAS Lacie cable to one of the ports on my router. My whole system works wonderful locally.

  The Lacie received a static IP address to 192.168.1.199

  My local network has an IP departure from 192.168.1.150 and ends to 192.168.1.199

  My router IP is 192.168.1.99

  I've assigned port forwarding to my Lacie (192.168.1.199) for ports

  20, 21, 25, 80 and 443.

  I tried other settings but no help. Help, please!

  Happy new year!!!

  Hey Scrooge.

  Thanks for your help... my SIN was in fact all along. I used my cell phone to connect to all this time. Today, I tried my work PC to connect using ftp://x.x.x.x and it is well connected.

  I appreciate your help and your patience.

• can only connect to internet access using wireless or ethernet cable

  I use a computer Windows Vista with Internet Explorer 8.

  When I try to connect to the internet from my laptop on a Netgear router I can connect only with limited access via an ethernet cable or wireless. My computer detects and attempts to connect (with complete connection) to the netgear router, but then the prompt appears on the screen, "connection takes longer than usual." Then, it displays "connection failure.

  I tried to use all the recommended solutions such as move the computer to a different location, automatically get new ip settings, etc... without success.

  In the past, I could access the internet without problems and the full connection and wonder if my college internet connection may have screwed up the settings.

  Thank you

  Hi Travis98,

  You can try to boot into safe mode with network and check if the problem occurs.

  Step 1: to start in Mode safe mode with network you can follow the below given steps:

  1. remove all floppy disks, CDs and DVDs from your computer and restart your computer.

  Click the Start button, click the arrow next to the lock button, and then click restart.

  2. do one of the following:

  a. If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, you need to try again by waiting until the Windows logon prompt appears, and then stop and restart your computer.

  b. If your computer has multiple operating systems, use the arrow keys to select the operating system you want to start in safe mode, and then press F8.

  3. in the Advanced Boot Options screen, use the arrow keys to select the safe mode with networking option and press ENTER. For more information about the options, see startup options (including safe mode).

  4 log your computer with a user account with administrator rights.

  For more information, you can consult the following link to start the mode safe mode with networking:

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Please post back and let us know the results.

  Hope the helps of information.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.