Similar Questions

• Enable AAA fails on the second ACS server

  I have 2 servers Windows 2003 4.2 ACS, who authenticate with AD. I have configured authentication GANYMEDE + both for my PIX 515 running version 7.24. GANYMEDE + authentication works fine on both. However, when I use the 'aaa authentication enable console LOCAL ProsperAdminAuth', the enable password only works with the first ACS server. When the first server is unavailable, it fails on the second ACS server and authentication failed on ACS "ACS invalid password" reports. It does not allow the LOCAL password. I checked all the password and there is no problem there. I know that for you, because GANYMEDE auth works. Someone at - he seen elsewhere issue or know what I might try?

  Thank you

  Vivek

  Hello

  Configuration of external database is not replicated between servers ACS so my guess here that is on your ACS secondary if you go to the external-> unknown user policy user databases, you will find that under configure enable password behavior you are on "internal data" instead of "The database which the user profile is required."

  -Jesse

• Pics of member comments on all hosts on the new esx Server

  Peaks mem comments on all hosts on the new esx server, but the operating system does not use the amount of memory.

  The results are same vm running on the esx servers

  HP DL380 G6

  Dual Core CPU 8

  Xenon E5520 2.27 GHz Intel

  VCA mode Intel Xenon 45 nm Core2

  Guest mem 95% +.

  HP DL380 G5

  Dual Core CPU 8

  Intel Xenon X 5450 3.00 GHz

  VCA mode Intel Xenon 45 nm Core2

  Guest mem typically 25-35%

  The 3 peaks located on the new server.

  The new G6 in the memory market settles after a while if I put manually:

  Use Intel VT-x/AMD-v for virtualization and EPT Intel/AMD virtualization MMU nec training

  If I move G5 servers all right, move them back it culminates on mem. waited for itself if it settles, but no go.

  PS we put in CVS mode on the cluster.

  New servers booted on peak still G6 mem comments.

  Any thoughts?

  You have to refer to this before KB ?

  vcbMC - 1.0.6 Beta

  Lite vcbMC - 1.0.7

  http://www.no-x.org

• Presentation of ID host ESX host LUN to the VCB Proxy Server

  I have a typical scenario where I have 3 ESX servers with 3 x 800 GB LUNS in a storage group separate on a CX 310 SAN box. The host LUN., of these 3 LUN Ids are 0, 1 and 2.

  I have a specific host that starts from SAN, from the same box of CX 310 SAN. At this point of time, I have no choice to use this server as a Server Proxy VCB. As far as my knowledge goes, LUNS of the ESX servers must be made visible to VCB Proxy Server, as they are presented to the ESX servers.

  My question here is, as the designated Proxy VCB server is booting from the SAN, he already has a host LUN 0 to Id the logic unit number this is the start of. The Id to host ONE of the first 800 GB LUN in the ESX Server storage group is also Host Id 0. Now, if I try to make the LUNS in storage group visible on the VCB Proxy Server ESX, is there not a shock of the VCB Proxy 0 host Id and Id host ESX Lun 0? I'm confused, I don't have a test envirinment where I could try this before I could actually go forward with any solution.

  My intention is to perform a backup outside LAN of the VMDK.

  Any help is that this respect is very much appreciated. Thanks in advance.

  (1) Yes, you can have different host for VCB then for your ESX host LUN ID

  (2) Yes, you can use the identifiers of naa, it will automatically use the identifiers of naa, no need to configure anything at all.

  Duncan

  VMware communities user moderator

  -

• Restore the entire ESX Server

  Hello

  I currently have a single ESX Server 3.5 running a cluster of virtual machines, including the vCenter who runs it.  The problem is that I am running out of disk space and want to slap in addition to disks and to rebuild the RAID array.  Since I have no second box to vMotion at how can I do this without having to rebuild my entire esx from scratch Server?

  Is it possible to use some kind of imaging tool that will recognize the VMFS partitions and create an image of the server on a large drive and then restore it to a larger painting afterwards?

  I have no other than VCB backup tools at my disposal.

  Thanks in advance.

  Take a look at the following Vmware KB

  http://KB.VMware.com/kb/1000761

  Some steps are listed for restore procedures.

• installation of the agent on the vmware ESX Server

  Hi, im trying to install the agent 2.7.6 on an esx server of vmware 3.01, somehow, the agent does not connect to the administration server, I opened the ports on the firewall of esx with esxcfg-firewall - openport port 7443 and 2144 but I still can not the agent to connect to the management server... everything I forget?
  
  Rgds

  Hi Nicky,

  We will clear up the confusion of port for the next version.  Regarding
  availability be yellow, I believe that it is through the combination
  the VMware API in 3.0 is much slower than ESX 2 times 20
  VMS exposes this recently fixed issue: http://jira.hyperic.com/browse/
  HHQ-437

  You can find a patch fixed the issue that should solve your
  lights of availability.  Let us know if that helps.  It is also possible
  to reduce the memory usage by disabling the plugins that vmware
  Buy adding to agent.properties:

  plugins.include = VMware

  You can also change the max heap size in agent.properties:
  agent.javaOpts =-Xmx128m

  On 15 January 2007, at 03:52, Haan Nicky wrote:

  > okay... It's already better... but first, autodetect didn t
  > work for hyperic settings, when you try to set it to 0 for the port.
  > He complains the port must be between 1 and 65535.
  > change the settings on the execution of the agent already has failed
  > either, so I killed the admin machine and deleted data
  > folder on the computer of the agent, after the reset and the
  > the right credentials and port 443 (Please note that the)
  > authd.client.port is 902... and not 443, check/etc/vmware/config
  > for this authd.client.port = '902', so I obviously thought that of
  (> What is necessary in the settings, maybe just state port 443 here?) I have
  > then started the inventory, which is quite long (10 minutes) and
  > memory and CPU was quite up on the esx Server (this is a double quad
  (> xeon machine with 16 concerts and about 20 vitrual machines running)...
  > the agent runs now, but somehow I think that the moment a large number,
  > availability is always on the yellow... I think that the agent
  > must refine even more here... on an esx 3.0 server there are only
  > 1 cpu and limited memory available for the linux Machinehote...
  > maybe it's not enough for the agent?
  >

• Unable to virtualize the host esx Server quadcore AMD Barcelona B3

  I have a server with AMD Quad Core CPU Barcelona B3 32 GB of RAM. I installed ESX 4.0 update1 on it successfully. After that, I try to virtualize esx server on this server. I added the new virtual machine with a standard configuration. When I try to boot the cdrom ESX4.0 I get the error message shown in the attachment.

  I tried with esx 3.5 and 4. Same mistake.

  cpuinfo on the esx host recognizes that UC is B3.

  I would be grateful no work around for this work.

  Thanks in advance

  It seems that your host is in an EVC cluster configured for Opterons third generation.  VCA usurps the guest not to not CPUID settings for a 'lowest common denominator' CPU, which is, unfortunately, a B2.  Try to remove the EVC cluster host.

• Upgrade virtual Center 2.02 VC 2.5 on the new server. Upgrade ESX 3.02 ESX Server 3.5. and add the new ESX Server.

  Hello

  We are due to upgrade our VMWare environment. ESX 3.02 x servers virtual Center 2.02 and 3.  We have new material on which to install Virtual Center and we are also adding a new ESX Server.

  I read various guides for virtual center upgrade and watched questions on the forum, but can not see everything that relates to the way I thought to do. I want to install Virtual Center 2.5 on the new server and I would refer her to the current virtual cenre database.  Is this supported?

  I then install ESX 3.5 on my new ESX Server and add it to the virtual Center. Then I would start the upgrade / rebuild other servers using VMotion to migrate all VM the next server to be rebuilt on the new server running ESX 3.5.

  Would this work.

  What is the best way to upgrade the virtual center of new material and a new Version?

  Thank you for all the advice that can be offered.

  Kind regards.

  Kevan

  Kevan says:

  I read various guides for virtual center upgrade and watched questions on the forum, but can not see everything that relates to the way I thought to do. I want to install Virtual Center 2.5 on the new server and I would refer her to the current virtual cenre database.  Is this supported?

  Yes, it is an upgrade that is supported.  Don't forget there will be an upgrade for your DB schema and it may take some time.  Just make sure that you have a good backup of your DB before you start.

  I then install ESX 3.5 on my new ESX Server and add it to the virtual Center. Then I would start the upgrade / rebuild other servers using VMotion to migrate all VM the next server to be rebuilt on the new server running ESX 3.5.

  I agree entirely, I drive rebuild is the way to go.

  Would this work. > What is the best way to upgrade the virtual center of new material and a new Version?

  Upgrade to the current version using the .iso image file.  Don't forget the license server, which is a standalone update and are located in the folder /vpx of the vCenter .iso

  Upgrade path:

  1 vCenter

  2 ESX

  3 VMware Guest Tools

  Thank you for all the advice that can be offered.

  I hope that was a little helpful as well

  http://www.VMware.com/PDF/vi3_35/esx_3/r35u2/vi3_35_25_u2_upgrade_guide.PDF

• Existing LUN on the second card CF

  Dear team,

  I LUN san mapped onto one of the esx host, I have two CF card on this esx host, but LUNS are mapped on a CF card, mutipathing if san team will arrange for there end and mapp all pay-per-view 2nd fc san LUNS will be it requires no downtime or just I have to rescan the adapter and it will detect all the SAN LUNS that were also in correspondence with the 1st CF card.

  Need your help...

  Concerning

  Mr. VMware

  Hello

  LUN ID are assigned on the side storage.

  Based on the ability of the matrix of storage you use, there are several options.

  That is to say,

  all LUNS shared is attached to a storage group, each storage unit on the inside as the SG not identifying his own logic unit number.

  When the storage Administrator allow several initiators (HBA) to access this SG will all see with the ID LUN storage devices configured in the SG.

  Some tables use a different approach.

  They provide storage devices on a per initiator basis, including the ability to individually assign LUN ID for a storage device.

  These berries are capable of presenting the same storage device to several intiators with different LUN ID.

  This did cause problems with older versions of ESX, as a best practice, so it is recommended to use the same LUN ID shared storage devices.

  Kind regards

  Ralf

• How to make non-visible control on the Front Panel appear at Design time?

  I have a few controls on the front whose visibility is changed (on or off) at run time. The problem is that if I stop the Run time, the visibility of the control remains in the running in design mode state. So I am not able to see or find the control to make changes in design mode.

  How can I make all the visible front-panel controls, or find and make it visible to a control on the front whose visibility has False?

  Thank you.

  It is documented in the help of LabVIEW.

  Hidden front panel display

  
  

  Perform the following steps to display a hidden front control or indicator. You can also hide the indicators and controls on the front panel.

  1. Find the terminal block schema for the object. "If you have multiple devices with the same type of data, right click on the terminals and select visible elements" Label in the context menu. Find the object with the label that corresponds to the object hidden façade.
  
  
  2. Right-click in the Terminal, and then select Show Control context menu if the object is a control or indicator to show if the object is an indicator.
  
  

  You can also use the Visible property to display the controls and indicators by program.

  You can also view all hidden front panel controls and indicators.

  Path: Fundamentals-> build the façade-> how-to--> configure the objects-> display on front panel of the façade hidden object.

• Lightroom CC - development of non-visible presets on the context menu in the library Module

  Just installed Lightroom CC 2015 - loving the speed increase in the develop module.

  When I select a bunch of images in the library module and right-click (Windows of course), 'developing' settings from the context menu has a number of things listed, but missing completely all presets that are usually visible.  This was voluntarily removed in Lightroom CC, or is this a bug?

  If I pass the develop module, all my presets appear on the left hand side correctly.

  In the library module, they are all listed in the box "Saved Preset" above to develop quickly, but they are just missing now from the context menu.

  I tried to reset all my prefs (ctrl + alt + shift on restart) - still the same.

  Any ideas?

  Paul

  Lightroom CC 2015 running on Windows 7 Professional SP1

  It is true, that they are eliminated because of the speed. Some users were too develop presets so he slowed down too.

• Non-visible value in the drop-down list box

  Hi all
  
  I have a bar of control with 5 drop-down list boxes.
  
  As the user, the value in a box, others are refined to include only items that are related to the user's selection.
  
  All works well with an exception in a single list, the value is this drink is not visible.
  
  Anyone has previously met and nobody knows how to correct?
  
  Thanks in advance for any help.

  Duh.

  In the one case where him point fails to show I was not have cast the value as a string.

  Casting solved the problem.

• File shares of some non-visible windows through the clientless ssl vpn

  Hello

  I have an ASA 5505 with the SSC module and were able to get the ssl vpn upward and running, for some reason, some of the shared folders do not appear when I connect. I checked permissions for shared folders which can't be compared to those who do, and they are exactly the same.

  Thank you

  Chauncey

  Don't forget to note the positions that helped you and mark it as resolved if this addressed the issue. Thank you!

• Non-visible service in the Integration Broker monitor operation

  Dear Experts,

  I'm working on integration between Financials PS and PS Finance Accounting student.

  I configured the nodes PSFT_EP and PSFT_HR in the two systems. Ping is successful at both ends.

  As the first step, I'll put up the Business Unit synchronization for

  Finance of PeopleSoft in Navision Financials.

  I activated the message BUS_UNIT_SF_FULLSYNC name with even publish a rule identifier in the two financial statements and

  campus of. I activated the service operations and also activated the roads. I checked the Inbound

  and outbound routing.

  When I launch full publish on the side of the campus,

  the service launched but he remains in New York and I found no trace in the FSCM.

  I tried to open the same side service FSCM but even after no sign in Service monitor.

  No data in the BUS_UNIT_TBL_SF.

  Queues are running on both sides.

  I left any stage.

  Kindly advice

  I closed my domain and load config again.

  Start the field.

  Goto the status and checked PSMSGHND.exe was here right now.

  Purge the new status field and activate my Machine and the update.

  His work...

  Thank you all

• Non-visible images by using a local server with XAMPP

  Hello

  I resurrected an old project, who has worked in the past.  Since then, Ive updated Windows (8.1) and Dreamweaver (CC) today I installed the latest XAMPP and created a folder named xamp2015.  I copied the old project (mysite) in the htdocs directory

  Now, the logic of the site works, BUT the images do not appear.

  They are stored here C:\xampp2015\htdocs\MySite\Images\Main

  My Site Local folder is C:\xampp2015\htdocs\Mysite

  Default Images folder is C:\xampp2015\htdocs\MySite\Images\

  The images will be displayed if I move them to c:\xampp2015\htdocs\MySite and update the links, but it could lead to a messy structure, which was not needed previously

  Does anyone have any suggestions?

  Try to create a new subfolder called "bob" and put a picture in it, link to it on one of your pages and see if it happens.

  In addition, which is up to the .htaccess file in your pictures folder?