Not able to write DVD after reformatting on Equium A60

Similar Questions

• Satellite A200: Not able to write DVD using Win XP

  Hello

  I have an A200 - 1 MB (PSAEO) that came with Vista home premium installed. After this downgrade to XP Professional, I am not able to write something on the DVD.

  Help, please. Model # for the DVD drive is TS-L632D.

  Help, please.

  Thank you

  James

  Hello

  I assume that you have installed all the drivers for the Toshiba driver page. You also update the BIOS to the XP version?
  You should do this if you have changed the operating system and if you use XP instead of Vista.

  May I ask how you try to burn data to a DVD disc?
  Are you using a 3rd party burning software?

  I use Nero and I m very pleased it burns different types of CDs and DVDs.

  Feedback would be appreciated.

• Not able to write CD or DVD on Tecra A4

  Since the last time I posted my problem of not being able to write CDs or DVDs using TECRA A4 with Mat * 830s DVD burner, I tried all the methods that have been suggested, but without success. I tried to update the firmware to version 2, but I wasn't able to update the firmware. I get the target drive not connected message.

  Hmm, so it's the pathetic situation, I am not able to write even a CD single in 2 years I bought the Toshiba Tecra A4. Whenever I put a CD in it says "D: / incorrect function." Is there a solution to this? I expect a last hope to make it work.

  At the end of my patience, if I can't write a single CD even after 2 years.

  Hello

  > but I wasn't able to update the firmware. I get the target drive not connected message.
  This message appears because you have used a wrong firmware and is not compatible!

  However, I have read you first assignment and all advice offered were ok.
  But have you checked that?

  Try going into control panel-> system-> hardware-> Device Manager and then under dvd/cd devices select the drive and right click and uninstall and then reboot and see if it helps.

  Please check if deleting UpperFilters and LowerFilters in the registry helps:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=16319&MessageID=59664

• Not able to write files to CD or DVD

  I'm not able to write files to CD or DVD. When I go to DVD - RAM (d :)) properties, I see only the following titles: general, AutoPlay, material and sharing.) I used to see a record position, but now he isn't. How do I restore to open and activate the recording function? I use Windows XP Home Edition with Service Pack 3. Drive: HL-DT-ST DVDRAM GMA - 4082N. Please advice. Thank you.

  Hi mark,

  · You receive an error message or error code when you try to burn a CD/DVD?

  · Do you remember recent changes made to your computer before the show?

  I suggest you to run the troubleshooter from the link below: your CD or DVD cannot read or write media:http://support.microsoft.com/mats/cd_dvd_drive_problems/en-us

  You can also check the links below: CD - R or CD - RW drive is not recognized as a recordable device:http://support.microsoft.com/kb/316529

  How to troubleshoot common problems that occur when a Windows XP-based computer cannot read a CD or DVD:http://support.microsoft.com/kb/321641/

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Satellite U200: I am not able to burn DVDs

  I have a problem with the DVD writer:

  Since I formatted (and then reinstall with the restore CD that was with the computer at the beginning), I am not able to burn DVDs!

  How can I do to get that!

  And also, it's weird, instead of showing a DVD player, there are 2: one for the CD, a DVD, when it's the same thing...

  I am able to read the DVD, but I am not able to burn them :(

  > And also, it's weird, instead of showing a DVD player, there are 2: one for the CD, a DVD, when it's the same thing...

  It's very strange it s confusing two s WEIRD appears in MY computer

  What you could do is remove the player of ODD (CD/DVD) Device Manager, then restart the laptop.
  Please check if the CD/DVD would be recognized correctly after reinstalling again.

• Why am I not able to print pictures after having previewed in photo WIndows Media Viewer

  Why am I not able to print pictures after having previewed in photo Windows Media Viewer

  It is a Windows XP forum... you are using WIndows XP?

  I don't know what you call Windows Media Photo Viewer.

  In Windows XP's default Photo Viewer is Windows Picture
  and Fax Viewer... and it has options of printing photos.

  Try right click on a thumbnail of the photo or the name of the file and see if you
  can choose... Open with / Windows Picture and Fax Viewer.
  The print icon located at the bottom of the screen...

  In addition, when you have a photo displayed in the Windows image and
  Fax Viewer... you can type... CTRL + P to print the Photo
  Assistant.

  Also, if you right click on a photo thumbnail or file name of the menu
  should include a print option.

• HP DVD Writer does not read or write DVD, but only the CD

  My HP DVD 1135t burner does not read or write DVD but only the CD. What is the problem? Please help me.

  CD/DVD players use different lasers for reading/writing DVD from the CD.  All indications would point to your laser DVD as having failed.  You could try to remove your drive and install it in another computer to see if the problem follows your player or your computer, but my bet is that the drive must be replaced.

  HTH,
  JW

• DVD RW drive (D :) will not read or write DVDs)

  My computer can not read and write DVDs and CDs.  Please tell me how to solve the problems.

  Thank you very much!

  Sue

  Hello

  Someone helped me to fix my computer, the problem disappeared.

  Thank you very much.

  Sue

• I am not able to burn DVDs on my Satellite A60

  Hello!

  I have a Toshiba Satellite A60 with a Pioneer DVD - RW DVR-K13A. And whenever I try to burn a dvd, it does not work. The drive detects the dvd but I can't burn. I tried several burning such as folder software now! and Intervideo WinDvD Creator. What I need to upgrade the burner or something.

  And the format of the dvd are DVD - R and I checked the manual, and it says: I am able to burn DVD-R.
  Thanks in advance.

  Post edited by: Slintas

  Hello

  This path is not easy to tell if there is only a few small problem or maybe a malfunction but from your description, I assume that the reader can read but not write DVD media. In this case, it is really possible that the drive is faulty.

  If you have tested with different DVD media and the different burning applications, I'm pretty sure that the drive is faulty.

• Could not read or write DVD-RAM

  Even if my material indicates that he can read and write DVD-RAM, all of a sudden I can't recognize discs dvd - ram, that I stored things on front. I followed one of the forums and has released Service Pack 2 and that worked for a while and then stopped working again after a few updates have been installed. I tried again to SP2 and then pushing out, but not joy. No idea how to fix this? I went through Fixit MS and the thing Upper and Lower filters, still no joy.

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Not able to use iTunes after that put 12.3.3 updated

  Not able to iTunes after put 12.3.3 updated

  After installing update iTunes to 12.3.3 (after the prompt), I'm not able to use Itunes. When ever open in 10 seconds a pop-up message is displayed which says that itunes has stopped working. a problem caused the blocking of the program works correctly. Please close the program. two close options to obtain the program and the program to debug.

  Please help solve this problem

  Hello! Try the steps suggested here:

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  If you can't install or update iTunes for Windows - Apple supports

  I hope this helps!

• Few of the virtual win XP not able to boot, office after login screen new accepts off.

  Hello

  I installed 12 Virtual desktop (WIN XP), and on 12, two are not able to start, when you turn it on, after the login screen again is done switch off automatically.

  What could be the reason?

  One last question, sometime, I saw that all the virtual office the maxmm cross limit memory only once, and then in a few minutes, come normal.

  Kind regards

  Mustafa Rashid

  Hello

  Moved to the forum of the Virtual Machine and the guest operating system.

  Best regards, Edward L. Haletky VMware communities user moderator, VMware vExpert 2009, url = http://www.dabcc.com/channel.aspx?id=279DABCC analyst [url]
  "Now available on Rough Cuts: url = http://www.astroarch.com/wiki/index.php/VMware_Virtual_Infrastructure_Security' VMware vSphere (TM) and Virtual Infrastructure Security: ESX security and virtual environment ' [url]
  Also available url = http://www.astroarch.com/wiki/index.php/VMWare_ESX_Server_in_the_Enterprise"VMWare ESX Server in the enterprise" [url]
  [url =http://www.astroarch.com/wiki/index.php/Blog_Roll] SearchVMware Pro [url] | URL = http://www.astroarch.com/blog Blue Gears [url] | URL = http://www.astroarch.com/wiki/index.php/Top_Virtualization_Security_Links Top security virtualization [url] links | URL = http://www.astroarch.com/wiki/index.php/Virtualization_Security_Round_Table_Podcast Virtualization Security Table round Podcast [url]

• Not able to install Windows after formatting hard drive

  I am not able to install windows on the computer. I have Dell Inspiron N5010.

  Put under alert.

  -Windows cannot be installed to disk 0 Partition 2.
  Details: Windows cannot be installed to this disk. This hardware may not support booting to this disk. Make sure that the drive controller is enabled in the computer BIOS menu.

  In the BIOS

  SATA - AHCI mode

  Hello

  When you formatted the disk you also partition?   Also, what version of Windows you are trying to install the system, and what media you are using to install it?

  Have you entered THE system BIOS and changed the SATA settings to see if you can get Windows to load on this subject?

  Todd

• Audio CD not playing not not in mast * a 820 s UJ on Equium A60-155

  Hello

  I'm having some trouble with audio CDs on my Equium A60-155 with the carpet * a UJ 820 dvd multi recorder. By audio CD, I hear cd albums purchased, not copies or CDs with mp3 files (I'm ripping my cd collection on a MP3 player through my laptop).

  A brief description of the problem is:

  Some cds do not play the disk at all - I can hear it clicking and buzzing and light orange on the eject disc, but it will not read the disk and the pc hangs until I have the disc. Some CD play, but with sound distortions (e.g. constant cracking and popping); and some CD and play ignite very well, without any problems at all.

  Windows Media Player is what I use to play the CD. The CD I'm unable to play fine on a normal cd player and on other PCs (I tried a number of these CDs on several PCs in my office and have no problem at all), so I'm confident drives real themselves are not the issue.

  I would also like to add that no audio CD (for example the software) and DVD playback absolutely perfect on my laptop with no problems whatsoever.

  I tried most of the advice in other posts here with similar issues:
  I have reinstalled/updated all the drivers, firmware and bios.
  I removed the dvd drive of the Device Manager and rebooted to force Windows to reinstall.
  I tried to clean the lens with a cd lens cleaning cd.
  I tried to play the CD via iTunes and RealPlayer instead of WMP, but have the same problems.

  I would appreciate any advice that anyone could offer. In reading the other posts it seems similar to the problem of lens calibration other posters have known, but I would have thought that he would not play any CD at all if that was the case.

  Please let me know if you need more information. I use Windows XP SP2.

  Thanks in advance,
  Ed

  Check this box:
  Go to the properties of the drive and select the Hardware tab. Then choose new drive and select Properties. Then check in the Properties tab, if the Enable CD digital option for CD-rom audio is marked
  Maybe it helps.

  I have although this could have something to do with audio copy that has been applied on some audio CD s protection.
  I read on the internet that many different readers might have some problems with these copy protections.

  Maybe I m wrong, or even it s calibration lens problem
  These problems might arise if the lens can not calibrate correctly. I mean that the reader may be able to play media and others not.

• Cd\dvd drive disappeared on Equium A60

  Hi all

  Can someone help me? I have an Equium A60. It's 18 months, outside the usual on heating problems and closing, now it starts but my DVD drive disappeared. I have a rug * a DVD-RAM UJ - 830 s. Win XP just didn't load it.

  He is no longer in 'my computer '. I'm in Control Panel of configuration and the 'systems' then 'system properties' and watched on 'Device Manager '. The drive is there, but with a big yellow exclamation point. So I checked the 'properties' it has the following message: "Windows successfully loaded the device driver for this hardware, but does not the hardware device. (Code 41) "and troubleshooting has no use.

  More than heating cooked my drive? I've updated the drivers for it, but this has no effect.

  Any ideas... ?? Thanks in advance...

  Hello

  When you use advanced search option, you will find several similar views with a solution to this problem, but once again for you http://support.microsoft.com/default.aspx?scid=kb;en-us;320553

  Please use method 1.