Not able to write CD or DVD on Tecra A4
Since the last time I posted my problem of not being able to write CDs or DVDs using TECRA A4 with Mat * 830s DVD burner, I tried all the methods that have been suggested, but without success. I tried to update the firmware to version 2, but I wasn't able to update the firmware. I get the target drive not connected message.
Hmm, so it's the pathetic situation, I am not able to write even a CD single in 2 years I bought the Toshiba Tecra A4. Whenever I put a CD in it says "D: / incorrect function." Is there a solution to this? I expect a last hope to make it work.
At the end of my patience, if I can't write a single CD even after 2 years.
Hello
> but I wasn't able to update the firmware. I get the target drive not connected message.
This message appears because you have used a wrong firmware and is not compatible!
However, I have read you first assignment and all advice offered were ok.
But have you checked that?
Try going into control panel-> system-> hardware-> Device Manager and then under dvd/cd devices select the drive and right click and uninstall and then reboot and see if it helps.
Please check if deleting UpperFilters and LowerFilters in the registry helps:
http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=16319&MessageID=59664
Tags: Toshiba
Similar Questions
-
Satellite A200: Not able to write DVD using Win XP
Hello
I have an A200 - 1 MB (PSAEO) that came with Vista home premium installed. After this downgrade to XP Professional, I am not able to write something on the DVD.
Help, please. Model # for the DVD drive is TS-L632D.
Help, please.
Thank you
James
Hello
I assume that you have installed all the drivers for the Toshiba driver page. You also update the BIOS to the XP version?
You should do this if you have changed the operating system and if you use XP instead of Vista.May I ask how you try to burn data to a DVD disc?
Are you using a 3rd party burning software?I use Nero and I m very pleased it burns different types of CDs and DVDs.
Feedback would be appreciated.
-
Not able to write files to CD or DVD
I'm not able to write files to CD or DVD. When I go to DVD - RAM (d :)) properties, I see only the following titles: general, AutoPlay, material and sharing.) I used to see a record position, but now he isn't. How do I restore to open and activate the recording function? I use Windows XP Home Edition with Service Pack 3. Drive: HL-DT-ST DVDRAM GMA - 4082N. Please advice. Thank you.
Hi mark,
· You receive an error message or error code when you try to burn a CD/DVD?
· Do you remember recent changes made to your computer before the show?
I suggest you to run the troubleshooter from the link below: your CD or DVD cannot read or write media:http://support.microsoft.com/mats/cd_dvd_drive_problems/en-us
You can also check the links below: CD - R or CD - RW drive is not recognized as a recordable device:http://support.microsoft.com/kb/316529
How to troubleshoot common problems that occur when a Windows XP-based computer cannot read a CD or DVD:http://support.microsoft.com/kb/321641/
With regard to:
Samhrutha G S - Microsoft technical support.
Visit our Microsoft answers feedback Forum and let us know what you think.
-
CD/dvd reads but not able to write. says 'hardware error 9216.
When I got this laptop it reads and writes audio and dvd movies fine but after about two years it stop working. whenever I try to write it not finish writing and guest says 'hardware error 9216. has concluded that it might be because I got more than burning software then maybe they could have a conflict with each other, but I could find something on how to resolve the issue so that why I'll try here.
It could be the problem with the software if have several software to burn and write as you say. You can uninstall one by one and after uninstalling restart your PC to see what problem a single cause. To better test, it is better to restart after every uninstallation. If you see system information, you can find the details in the conflict, but it is a little technical.
Restore your system before this problem to occur.
You can try to run this command at the command prompt:
sfc/scannow
Make sure that your system is updated and the latest service pack installed.
Another thing is that it might be due to malicious software, and in this case, you could run full system scan with:
http://www.Microsoft.com/security/scanner/en-us/default.aspx
-
Hello:
DVD players, both came with the PC and MSI DVD - Rom I bought through the Internet works ONLY for playback of CD - r and DVD - r, but the two do NOT write/burn brand new DVD and CD - R, popping up in the middle of the screen,... Please insert the blank in the E floppy when I actually inserted in the DVD drive.
I have uninstall and rebooted the PC, in the hope that readers DVD works OK,... but nothing helps.
Wonder if the registry damaged for DVD player, or what other problems causing this problem?
Any help on this would be greatly appreciated.
Hello
Have you checked if the CD/DVD drive you purchased is a recordable disc? If this is the case, there should be an indication (e.g., CD-RW/DVD-RW). You can also check for the indication Device Manager.
If you have confirmed that it is indeed able to write on the discs, then try to activate the IMAPI. To do this please see the instructions below.
1. click on start
2. click on run
3 type "services.msc" (without the quotes)
4. in the window that opens, you select IMAPI
5. right-click on it and select "Properties".
6 start the services.
-
Not able to write DVD after reformatting on Equium A60
Help, please
I had to reformat my drive hard once the system has been corrupted, now, the drive is not recognized as dvd player and do not write DVD.
What should I do
Thank youHello
I found a DVD-Ram driver Toshiba driver Web site.
Please download and install this driver.
Hope that this procedure will solve your drive problem. -
itshow msg
Insert the disc pls
Hello
Step 1: Please do all the same underneath if you did some before as is often total
a process that solves the problem.Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
below.
Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitTry this fix manually if the Fixit 314060 does not work
http://www.pchell.com/hardware/cd_drive_error_code_39.shtmlYour CD or DVD drive is missing or is not recognized by Windows or other programs-
a Mr Fixit
http://support.Microsoft.com/kb/982116The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
for Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
Vista installation after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
manufacturer of device to see if there is a firmware or drivers for your drive if necessary.===============================
Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.Did you follow the Troubleshooting Guide for the reader who still does not work? There are
the entries in registry that the troubleshooter does not solve and those who "might" be the cause.Check with your Maker system and a device for the two possible firmware updates and
the correct registry entries for your car.Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
the parameters.HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
-----------------------------------------------------------------------
You can probably find more info here and maybe even the exact registry for your CD/DVD settings
drive from someone with the same model.Forums - a lot of expert real help
http://Club.myce.com/CD/DVD units
http://www.myce.com/storage/Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
nothing change) - find the DevManView device and then make a right click on it free in RegEdit.DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
devices and their properties in flat table, instead of the tree viewer
http://www.NirSoft.NET/utils/device_manager_view.html===============================================================
Check with Toshiba support, their drivers online (update or reinstall) and their forums.
Toshiba - Forums
http://laptopforums.Toshiba.com/Toshiba - Contacts
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/navShell.jsp?CF=su_contactToshiba - drivers - access your model
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=downloadToshiba - Support
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jspI hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
-
What do you think could beb solution?
I tried a solution by Microsoft, but I could not find filter lower or higher in the right pane - so I had to give up.
See below;
Windows Vista
1. click on Start
Collapse this includes this im
and then click all programs.
2. click on Accessoriesand then click run.
3. type regeditand then click OK.
Collapse this includes this image
If you are prompted for an administrator password or a confirmation, type the password, or click allow.
4. in the navigation pane, find and then click the following registry subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
5. in the right pane, click UpperFilters.
Note You can also see an UpperFilters.bak registry entry. You don't have to delete this entry. Click UpperFilters . If you do not see the UpperFilters registry entry, you may still have to delete the LowerFilters registry entry. To do this, go to step 8.
6. in the Edit menu, click delete.
7. When you are prompted to confirm the deletion, click Yes.
8. in the right pane, click LowerFilters.
Note If you do not see the LowerFilters registry entry, unfortunately this content can't help you. Go to the section "next steps" to learn how you can find more solutions or more help on the Microsoft Web site.
9. in the Edit menu, click delete.
10. When you are prompted to confirm the deletion, click Yes.
11. exit the registry editor.
12 restart the computer.
Delroy
Hello
There are several methods to check the high low filters and maybe it's not yet the real
the cause of the problem.-------------------------------------------------------------------------------------------------------------------
Step 1: Please do all the same underneath if you did some before as is often total
a process that solves the problem.Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
below.
Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitTry this fix manually if the Fixit 314060 does not work
http://www.pchell.com/hardware/cd_drive_error_code_39.shtmlYour CD or DVD drive is missing or is not recognized by Windows or other programs-
a Mr Fixit
http://support.Microsoft.com/kb/982116The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
for Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
Vista installation after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
manufacturer of device to see if there is a firmware or drivers for your drive if necessary.===============================
Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.Did you follow the Troubleshooting Guide for the reader who still does not work? There are
the entries in registry that the troubleshooter does not solve and those who "might" be the cause.Check with your Maker system and a device for the two possible firmware updates and
the correct registry entries for your car.Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
the parameters.HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
-----------------------------------------------------------------------
You can probably find more info here and maybe even the exact registry for your CD/DVD settings
drive from someone with the same model.Forums - a lot of expert real help
http://Club.myce.com/CD/DVD units
http://www.myce.com/storage/Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
nothing change) - find the DevManView device and then make a right click on it free in RegEdit.DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
devices and their properties in flat table, instead of the tree viewer
http://www.NirSoft.NET/utils/device_manager_view.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
-
USB disabled not able to write and read access but user authorized to datacard possible
Dear all,
I need usb disabled unable to access both read & write. But able to access a Data card and USB mouse. This is possible thanks to a block log. Please post your suggestion.
Hello
1. What is the exact problem you are facing with USB?
2. you receive an error message?
3. have you made changes on the computer before this problem?
Please provide us with more information to help you further.
-
Not able to write correctly in the Arabic language in artificial intelligence
Hello
I'm unable to write correctly in In Design and Illustrator of the Arabic language
Hi Ali,
If you have installed the Arabic version of HAVE and ID, please see the following links for more information:
Type of Arabic and Hebrew in Illustrator
Features of Arabic and Hebrew in InDesign
If this is not the case please check the previous post and install the programs correctly.
Thank you
OM
-
"Not able to write to the configuration file" when config editor in the admin tab
Hi guys,.
I have install OBIEE 10.3.3.4 on a GNU / linux RH (with OS user obiee) and Oracle Application Server 10.1.3.1 on the same box (with OS user oraias).
When I want to change some settings in the admin tab of BI publisher (administrator/administrator under the name of login/pass) and click "apply."
I get the error "could not write to the configuration file. Once I changed the configuration to 777 properties, the error is still there. And I also try to change the SECURITY MODEL to the MEO, but still no use.
I did a test, for example, when I change something in the admin - JDBC - Oracle BIEE and apply then I got the error. If I update xmlp/DataSource/datasources.xml manually, the change can be seen after that I opened the admin of page - JDBC - Oracle BIEE. That means I have find the right file and the file access properties is ok.
Other parameters such as the Scheduler Configuration, I had the same error when apply. But the "Test connection" and "Installation diagram" function.
Can someone give me some advice on this? Thank you
Scott
Published by: Typhoon on March 20, 2009 12:59 AMIn what way is your xmlp? You are absolutely sure that the user of the OAS (oraias) can write to this file? If you have used another user for OBIEE then your will need to change the owner of the file or put them in the same group, and change the file permissions.
-
Satellite PM30: Not able to write CD
Whenever I try to write in a new CD, I get an error message indicating that the CD cannot be written to. I tried different CD without success. My wife also has a Toshiba and has no similar difficulty with CD.
If I changed a parameter and if yes, how can I go back?Hello
What burning program did you use?
I use the Nero software of engraving and it works properly.
Have you tried to remove the disc?
Sometimes lead removal problem. You must remove the drive from Device Manager CD. After restarting again the operating system should recognize the drive correctly. Maybe this procedure will solve your problem.Good bye
-
not able to write the data through data acquisition
Hello
In fact, I need to send a code word (text file) from the program matlab through my data acquisition (OR-USB-6215). my program (transmitter.vi [case structure: page2]) attached below has a problem to do the task. whenever I run the program it gives me an error like
Error-200479 occurred at DAQmx start Task.vi:2
Possible reasons:
Measurements: Specified Operation cannot be performed during execution of the task.
Task name: _unnamedTask<84>
At the moment I don't see output in my oscilloscope. But, if I highlight my performance I observe my samples on the oscilloscope with the following error message
200288 error has occurred in the DAQmx write (analog 1-d 1Chan NSamp DBL) .vi:3
Possible reasons:Measurements: Attempted to write a sample beyond the final sample generated. The build is stopped, so the sample specified by the combination of the position and the offset is never available.
Hi Raja,
What I did is I moved the 'write DAQmx' outside the while loop. That made the VI in this case is read the file and passing it to a table, and then this table is formatted a waveform to be written to the data acquisition device.
With respect to the way in which the data is read, I don't change anything, it was based on your original code. A good way to know if you write the correct data is to check the chart view in VI.
So the question is, is the graphic display showing the good waveform?
Best regards
Faris
84> -
Satellite Pro M70-113: not possible to write on CD - R and DVD-R
Hello
I have a Toshiba satellite pro m70-113 laptop.
Playback problems:
I'm unable to read cd - r. It's really strange that a few days earlier these CD - R have been reading very well on my drive.
and when I click on the cd drive in my computer, an error dialog box shows and says f: is not accessible, incorrect function. Here's a screenshot of the error... :
http://img64.imageshack.us/img64/9574/1bp3.jpgAnd when I try to read my DVD-R, a few times they read very well but sometimes it does not read and the drive LED is lit when it does not read the dvd - r.
When it reads the DVD-R, the following error message comes: screenshot here: http://img172.imageshack.us/img172/9674/2bc0.jpgWrite problems:
After getting reading problems, I tried to test my drive writable.
And I found that I'm unable to write on cd - r. I used alcohol and Nero once but without success.Although the same content when it is burned to cd - rw, it is a success.
I am able to burn successfully on a support DVD + RW 4 x with data amounting to close to 4.34 GB for DVD5...
When I insert a DVD - R Virgin car doesn t detects it as a blank media and the keps LED on lighting constantly and if nero State doesn't detect my DVD even! I'm not able to write on my DVD-R media...In short: write to RWs is possible for both cd - r and dvd + RW not possible of writing on CD - R and DVD-R.
Please help me.
It is only 7 months since I bought this laptop and believe that there may be no other person on this planet who looks after the training better than me!
Really, I have not much used this drive and never scratched/gradient/local support, only the Supermedium media inserted.Thank you
Hello
Well, based on your description it sounds like the drive cannot calibrate the lens and, therefore, it of not possible to read or write to these media.
Usual it of not possible to fix this and the replacement drive is necessary.You can also consult the user manual. You will find a list with all supported and compatible media.
I also found this topic in the forum:
http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=13170&MessageID=48243 -
Satellite M30X-165: Mat * a UJ - 831 S is not read and write any DVD
Hello
the next problem is sticky on the laptop Satellite M30X 165 with the burner Mat * a UJ - 831 S: it can read and write CDs, but is not able to write them to DVD or even read some of the ones I've burned and also read in the same drive. Even at the start of the DVD, it does not start from the recovery DVD, the player starts and slows down very quickly.
Without doubt, it must be put at the service of repair or someone has other suggestions?Could you please tell me how long the repair takes (I know what it takes to install the desktop temporarily used).
Thank you
Post edited by: DerSeher
Using burning software, it detects the DVD, but invite you to an "error of calibration power (037303).Hello
If you cannot use recovery media, I guess that the drive is defective and must be replaced.
Maybe you are looking for
-
Laptop was stolen and have been returned, but have the password on the bios please help me RE051ST? Ive treid many passwords and it returns error code 75237870 can you help me please?
-
Windows Update 80070246 error code
It says "Windows cannot check for updates ' and this is the error code I get every time. Any help? Thank you.
-
"The feature you are trying to use (TrayApp) is on a removable disk or a CD-Rom, which is not available. If please insert and try again". This is the error message I get, but I don't know where it comes from or how to prevent it from popping up. It
-
HY huys, I do an application that allows a user to connect and after it connects it shows the user name. Here's the code that display the user name when the user logs on: public LoginSuccessScreen (String username, String selectedDomain) {}Add (new L
-
Why is the "blind" synchronization: I want to know which remains to be synchronized images
Hello!I have a boring bit of the issue of synchronization with LR CC 2015.6When I want to quit smoking, I have this message, which indicates one, or synchronizes more photos:But I don't know what picture it is! I don't even know if there is a problem