OfficeJet Pro 8600: Flashing blue Internet

Similar Questions

• cant WiFi connection HP Officejet Pro 8600 e-all-in-one printer to internet

  I can't get WiFi HP Officejet Pro 8600 e-all-in-one printer connect to internet... at least I think that's the problem. I followed all the instructions on the HP print and Scan doctor as well as solve problems of failure to install HP. My router is working fine for everything else and I entered the router the static address for the printer.  It seems that my printer thinks it's connected to my WiFi (Ihave WPS it several times), but when I type there nothing appears in my IE IP address. My router does not see the printer either. I have the latest driver installed on my computer. I suspect that this may be a router problem: new Asus Double 450 Mbps N Router router (dual - band, but it appears my router uses the 2.4 Hz band to connect with WPS). Windows 7 64.

  Any help is appreciated!

  Hello NRHII,

  Welcome to the HP Forums!

  I understand that you are unable to connect the Officejet 8600 via a wireless connection. I will do my best to help you! I would recommend power cycling the router, the printer and the computer:

  (1) turn off your printer
  (2) unplug the power cord at the back of the router
  (3) restart your computer
  (4) wait less than 60 seconds, reconnect the power cord to the router
  (5) turn the printer, wait for the computer to turn on

  The wireless light blinking on your printer? If so, please reconnect the wireless on your printer using the Wireless Setup Wizard: (this information is declared here.)

  1. On the touch screen of the printer, press the right arrow key ( ) to display the second navigation screen.
  2. Tap the Installer icon ( ).
  3. Tap network , tap the wireless configuration wizard , and then press continue . The printer looking for available networks.
  4. Tap the name of your network and then press OK .
  5. If you are prompted, enter the password for the network, and then press OK . The printer connects to the network.

• HP officejet pro 8600 more - cannot access internet after several hours

  HP officejet pro 8600-after that I re-boot, I can access the internet for several hours, but after awhile, I cling on websites, I try to go to. If I unplug the printer and restarting, I accecss all websites all the time. I thought iwas hooked on a scan (which was never initiated by me), but I'm not sure. Any suggestions? I'm running on a Dell XP laptop.

  Thankx

  Hello

  Please visit the link below to fix the problem.

  http://support.HP.com/us-en/document/c03149924

• OfficeJet Pro 8600 Plus question (s)

  Product: HP OfficeJet Pro 8600 more

  OS: Win7x64

  Error Msg: B86ECEF4

  No change

  Brought this puppy home, it is out of the box. followed the instructions (removed all the pieces of Ribbon or protection). Cord plugged. Press the power button.  HP logo comes up, is there for about 3-4 min. one blue screen (blue screen of the window thinking of death which lasts 2 seconds), gives me this code B86ECEF4. Goes to a white screen with 7 icons are flashing (1 blue, 1 red, 5 whites) on the LCD screen. Wireless blue blink, the 'X' red, white is at home? , < and=""> and the back button. Start button / stop also flashes green. No internal sounds. If I move the door down (where I would put the ink of the cart, nothing moves out there.

  Any ideas. Defective? You missed a step?

  It seems that you will have to Contact HP for warranty repair.  If you live in the United States, call 1-800-HPINVENt

• HP Officejet Pro 8600 more cause the crash

  I have a HP Officejet Pro 8600 Plus, it is usb connected and connected wireless.  Sometimes when I print it (not always) causes a blue screen to appeear and the computer reboots and asks me if I want SafeMode ect.  Anyone else has this problem or knows what could be causing the problem?  I am running Windows 7 Home Premium 64 bit, with a modem cable for internet and a Linksys E1200 Wireless N network connection router enemy.

  Remove the printer from the system and uninstalling all the software.  Download and install the software features and drivers complete form here.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&LC=en&DLC=en&product=4323648

  Now install it and try again.

• HP Officejet Pro 8600 + "there is a problem with the printer or the ink system... »

  I have a HP Officejet Pro 8600 + which is coming up with an error message. This just happened out of the Blue yesterday. The printer is a little older than a year.

  It is said:

  "There is a problem with the printer or ink system. Printhead not missing not detected incorectly installed or incompatible.

  I've deleted and reinstalled ink cartridges, head, unplugged, cleaned up, etc etc.

  HP Officejet Pro 8600 +.

  Product number CM750A
  Sequence number {content removed}
  Not under warranty

  Please notify.

  I'm sorry that you are experiencing this issue. Here is a link that can help you with the ink system.
  http://goo.GL/BXDFf
  
  It seems to be a bad printhead, or it needs manually cleaned with water and lint. If these steps do not resolve the problem, contact HP (1800-474-6836) support.

• AirPrint is not my officejet pro 8600

  AirPrint is not my officejet pro 8600

  Go to settings on your iPad. Select the wifi.  Tap the blue arrow next to the network name in the list that your printer is on currently.  When the network settings page, make sure that the http proxy setting is set to auto.  This solves the same problem I had with the 8600 printer.  I hope this helps!

• HP Officejet Pro 8600 more print but not scan

  I have an Officejet Pro 8600 and I use Windows 7 Ultimate (64 bit) and it print and copy but will not scan. I had a hell of a time trying to get this thing to scan - I even spent an hour and a half with HP technical support and they could not fix it and finally gave up and call me Micro$ oft said that it must be a windows problem (Windows is up to date, incidentally).

  I tried to open the scanner software and nothing happens when I click the icon - the loading icon flashes for a second, then only the mouse pointer. Nothing happens if I try to boot from all programs. Nothing happens if I try to scan to the computer of the other printer told me the failure of sweeping and that there could be reasons of severalpossible (unrelated, software used, etc.).

  I have installed and uninstalled. A couple of times he was having trouble with the installation, but finally got it connected. Once it would not uninstall in Control Panel until I did it directly from the HP folder. I connected it by USB and wireless. I installed the version of bloatware. I cleaned that out and I tried the only version of drivers. The HP support person had me go and removed a bunch of stuff in the registry. I tried to run as an administrator. Nothing works. I even tried to scan using Windows Fax and scan. I disabled Kaspersky and made sure that my firewall is turned off.

  I am at my wits end with this and certainly regret my purchase at the moment. Help!

  Hello, it happens to the analysis of Windows (WIA) and generates an error:

  "The Windows Imaging service does not work... If the problem persists, you will not be able to scan using the applications that use this service, such as Microsoft Paint. Scanning software HP could still work. »

  It asked me to restart, and then re-run the diagnostic tests, but I got the same result.

  Then, I jumped to HP Scanner Twain and got another error:

  "The Twain component is not working properly because the product is used by another process. Save your work and close all applications. Turn the product off, turn it on again, and then click on restart and repeat the test. »

  He told me then the problem persists to uninstall the software, then reinstall the Full Feature software (I did, but available).

  * EDIT

  Problem solved!  After you had me run the diagnostic tool I googled the WIA problem and found that many other people had the same problem. A person has a response from Micro$ oft saying that it was a Windows 7 issue and how to fix it - this is the text I found:

  To start the WIA service, you need start all services of dependence. To start the dependency services, please follow the steps mentioned below:

  -> > click on start-> type "services.msc" and press ENTER, once you get up the services window, please do the rest steps.

  -> > first check and write down all the dependency services: -

  -> > right WIA-> properties-> tab dependence, check the services of name listed there.

  It must contain the following services:

  * RPC remote Procedure Call

  -> > DCOM Server process Launcher

  -> > RPC end point mapper

  * Detection material core

  Make sure that all of the above services are started in the services list.

  Last time, we started the Detection hardware Kernel, which solves our problem.

  (Andy, it's important.  Choose "Detection hardware Kernel ' and start this service which should start your 'Windows Imaging Acquisition '.  If it does not then select WIA and change the departure to "automatic".  This fixed my problems) after all dependency services start, please try to start, WIA service to solve the problem of .                                                                                                                                                                                       

  (For those who are doubtful with computers, like me, when you click on the start icon, you can type services.msc in the box of research programs or click on run and type it in there). Once inside the list of services, you can look at the dependencies by right-clicking on the Windows Image acquisition service and selecting Properties. Take note of these dependencies. Then back to the main list and watch to see if these dependencies are started. My Shell Hardware Detection says disabled, so I right click on it; However, starting selection is grayed out and I couldn't select it from the drop-down list box, so Startup type I selected Automatic, apply, close the Services window and then started my Scan software and presto, it worked.

  Thanks for setting me on the right track!

  
  

• OfficeJet Pro 8600 - Macbook Pro and Macbook Air does not print

  Products:

  • HP Officejet Pro 8600
  • MacBook Pro (Mac OS X, Version 10.7.5)
  • MacBook Air (OS X, Version 10.8.2)

  Question:

  • Why my Mac initially print fine, but now will not print?

  Full article:

  I have a wireless network in my house that consisted of a 30 MB cable internet, Netgear 900n, HP Officejet Pro 8600, 2 laptops from Dell with Windows 7, a laptop Lenovo with Windows 7 and Dell with Windows 7 trick, all printed matter very well.

  The HP Officejet 8600 was added to my network about 2 months ago.

  I added a Macbook Pro and Macbook Air about 3 weeks ago.  The two Macs printed fine for about a week.  Then suddenly they stop.  I spent about 2 hours on the phone with HP's Service, and finally, they said to my router.  So I called Netgear.  NETGEAR was useless!  They wanted me to accept fees for services before they would even discuss the issue.

  As a result of information provided by the HP support service, and because Netgear will not support their product, I quickly bought a new router - an Apple Airport Extreme.

  Macs will recognize the printer will print if connected via a USB cable, but do not print wirelessly on the Officejet Pro 8600.  The fine impression CPA.

  The frustration that is felt is made up by the fact that Macs printed very well with the Officejet Pro 8600 2 weeks and now the printer shows just "idle"... even with a new router. (see image below)

  Please help, thank you very much for all support.

  As a side note, the representative of the HP Service was very friendly and definitely tried to support the HP product, which is much more I can say about Netgear.

  Thank you

  

  Hello

  More likely a problem with Multicast, which Apple devices are relies on to communicate with the device through the network.

  First try unplugging the router for 30 seconds.

  Connect to the power supply and wait 2-3 minutes.

  Turn off the HP printer and turn it back on, then check all difference.

  If it persists, try to change the configuration of your router as follows

  Note: the settings below are not related with the HP product, I provide you with the steps as a best efforts and those based only on my own knowledge. You can try to change the settings of the router at your own risk:

  1. Open the router configuration page (you'll find listed as the default gateway by clicking the icon on the printer wireless, then print a network configuration report.
     
  2. Click the Advanced tab.
  3. Click the configuration option in the menu, and then click Setup WAN.
  4. Be sure to uncheck the box Disable IGMP proxy transmission and apply the changes.
  5. Click on the LAN configuration on the same Setup menu.
  6. Set the RIP RIP-2 Version and apply the changes.
  7. Restart your router and then check any change.

  I hope that you will find useful information, you can also use the guide to the user below for more information:

  http://www.downloads.NETGEAR.com/files/GDC/WNDR4500/WNDR4500_UM_07DEC2011.PDF

  Shlomi

• OfficeJet Pro 8600 more printer

  I just bought the printer more Officejet Pro 8600 & installed without any problems, but it doesn't connect to the internet/web services? It is connected to my home network & print etc, but when I try to activate the internet according to the guidelines, it searches for a while with "Enabling Web Services (ePrint & Apps)" on the screen & then reads "Web Services (ePrint & Apps) could not be activated.

  When I tried to activate the web service during the instalation, reading pages as if she did not go off I would go to a page to download the necessary drivers but this never happened and the only thing I could do was to select the button 'Next', who finished the installion without the work of internet/web service.

  Does anyone know of this problem and if so, please can you me how to connect my printer to the internet.

  It's great to hear Roses66. "If you could mark my previous post with the ' accept as Solution" it will help others in this community to find our easy conversation.

• HP Officejet pro 8600 more scan-to-Email problems

  Having a printer above, connected to my network through a static IP address. Interruption of the connection some time after the firewall on the pritner ago was accidentally tunred on and corrected cela by restoring the defaults on the printer control panel. Restored the connection via the EWS cnda wireless printing now laptop, PC and mobile devices all via the wireless.

  It, scan to e-mail settings are exactly as they were before the occurrence of the problem with the firewall (when they worked very well), but now do not work - EWS fails when he tries to test the parameters of ASNA to electronic mail. I use the standard server outbound smtp and port 25 as advised by my electronic internet/mail provider, but nothing helped.

  When I try to activate ePrint, I get a similar message: "unable to connect to the server.

  Is there something that I need to reset or reconfigure the printer?

  Concerning

  RedRoscoe

  Hello RedRoscoe,
  
  I would like to see if I can help with the Officejet Pro 8600 Plus scan to E-mail and Web Services questions. I think that the issues can be addresses by two steps, I hope.

  About scanning to E-mail, you can be blocked by the two-step verification. What is the email client that you want to activate the printer for, MSN, Gmail, etc.?

  Issues of Web Services, try to apply a manual DNS 209.244.0.3 & 209.244.0.4 to the printer's manual I.P address.

  See you soon,.

• HP Officejet Pro 8600: HP Officejet Pro 8600 not printing pictures

  With the kind cooperation of RnRMusicman and other knowledgeable people here, I could solve virtually all the problems I had Windows 10 to my HP Officejet Pro 8600, work flawless long since I bought it and while I was using the Professional Windows 7 operating system.  I was able to solve the problems of scanning and printing.  I should say that I can NOW print letters, notes, etc. I wrote on WordperfectX6, scanning photos, documents, etc. without any problems.  However, today, I tried to print photos of two 2 'My images' files and everything seemed to go OK, I got the display window to ask me how many, what size, photos etc I wanted to print and I clicked on print, then got another window showing the progress, but there was absolutely no response from my HP Officejet Pro 8600.  I tried to unplug and plug in again, restart, using the HPPSdr.exe and telling me everything is beautiful - but of course, this isn't.  When I tried to choose in the menu to go online to more possible solutions, I still said that I am not connected to the internet.  I hope I'm not overstaying my welcome to these forums.  It is a serious problem, I want to overcome since I have to print photos from time to time for projects.  Thanks in advance to you all and know that I am very grateful for past assistance which has solved MOST of the problems.  This one I didn't know until I tried to print photographs, lol.  As I said the OTHER impression, as WordperfectX6 is absolutely no problem only photographs.  Even looking at the "see what's printing" I do not see the ORDERS that I sent to the printer.  It is completely empty.  Thanks again.

  First of all, I do not deserve the title of "Guardian", lol.  I had adjustments and is raging after the upgrade to Windows 10 trying to do my job of Hewlett-Packard Officejet Pro 8600 (blah, blah blah).  I tried all kinds of recommended patches and nothing has been done, or he helped briefly and then the problem resurface.

  Feeling totally beaten yesterday, 2 November 2015, I deleted every single file from HP, fix, program, diagnostic tool ALL.  Then I unplugged the printer from your telephone line and plug its USB connection to the computer.  It was 19:00, 2 November 2015.   I then dug around and found the original set of the instructions that came with the printer when I bought it on amazon about two years ago.   Left on my desk, resolved to do battle with these unbeatable hi-tech "monsters" overnight.

  This morning, November 3, 2014, at 6:30, to feel refreshed and ready for battle, I discovered by accident that my DSL provider, century link, had a firewall (in addition to one already, I have in my software) so I advanced and off to see if that would help.   I just reconnected it on the printer, BUT this time I have not re - download HP software.  AND HERE, my Officejet Pro 8600 works again!  I can print from WordPerfectX6, I can print some photographs-YAY!   The only thing I'm still not able to solve must be able to print the pages of the internet.  For example, I tried to print a page of amazon.com and when I went to 'print' I was delivered to a Fax template.  This happened also when I clicked on "Print preview" - but I can live with THAT.  So, I walk away from the battlefield until I totally lose my sanity and tell me "that's close enough," lol

  Another by-product happy to remove the firewall of the century-link, which I didn't even know existed, it's NOW, I was able to receive updates from Dell, which had previously been cancelled/blocked, ostensibly by this firewall 'stealth' of my DSL provider which I didn't even know existed.

  Thank you!  To you all, who tried to help and who actually HELPED thanks to your suggestions.   Who would have thought that do not try to download HP ALL and eliminating a firewall that I didn't even not existing would solve 99% of the problems.  Thank you, Hewlett-Packard to also operate these forums!   They are EXTREMELY USEFUL!

• OfficeJet Pro 8600 Plus: network capability are not available

  Dear Sirs,

  The Officejet Pro 8600 Plus has already been set for a wireless connection. It was primarily used with the USB port.

  We've tried lately set up the wireless connection, and we couldn't.

  We received the message: network capabilities are not available.

  We could not move forward.

  We tried the factory reset, buit didn't work.

  I appreciate your help to resolve this isse.

  Concerning

  Ibrahim

  Please come back to me @Shahin_ij. I think the printer reset will solve the problem. I'll send you a PM (private Message), but before I do, please see the HP Privacy Statement.

  This privacy statement informs you of our privacy practices and the choices you can make about the way information about you and your online activity is collected and how that information is used. This statement is available on our homepage at the bottom of each web page of HP and HP.com.

  There are a growing number of messages in this forum and elsewhere in the internet with the steps to do a reset on different printers.  Reset to will sometimes fix problems, so resetting is not the issue.

  A few resets require you to enter key combinations to open special menus on your printer that you were supposed to never access.  These special menus are used by developers and staff support for debugging of problems, but they are not intended for inexperienced users and can have unexpected results.  A wrong button push and you might no longer have a printer, but rather an expensive paper weight.  On top of that, if you happen to the 'brick' the printer in this way, it is considered as customer induced damage and voids the warranty automatically. These resets are only intended to be distributed and used as a last resort and under the direct instruction of a representative of the HP technical support. They should not be made lightly!

  Reset the printer: what you need to know

  Please check the little envelope on the upper right of the forums page to check your Inbox of Forums.

  

• Page numbers and date stamp for Officejet Pro 8600 more

  Just installed Officejet Pro 8600 Plus.  When I print documents, I need to print WITHOUT the page numbers in the header (ie: page 1 of 4) and the date at the bottom.  I lived all the parameters that I find and cannot find this option.  Help, please!

  Hello

  You can remove the default header, footer... using AMPe configuration. This example so for Firefox on the tab "margins & header/footer":

  

  You simply give all areas "in white".

  Update: Very similar to Internet Explorer.

  Kind regards.

• E-mail print Officejet Pro 8600 Plus

  I can't print from email, I can print PDFS and all documents in word or excel, but not email.  I reinstall the software and the same thing happens.  All of the suggestions. Officejet Pro 8600 Plus with Windows 7 using.

  How to access your e-mail?

  * Do you connect to a service of e-mail via a web browser?

  * Or you are using a client such as MS Outlook e-mail software?

  If you log on to an e-mail via a web browser client, then you do in Internet Explorer?  Have you tried multiple browsers to ensure that the problem does not follow?

  I would also try another driver, such as the driver of c 990, to see if it is a driver compatibility problem.  For more information about how to use another driver, see thread of Shane_R found here.  I hope this helps.