OfficeJet Pro print heads

Similar Questions

• HP 8600 officejet pro printing issues

  Hello

  I have an officejet pro printer hp8600.  I have connected to a network. I had to reinstall Windows 7 64 bit on my computer following an accident.  This meant also to reinstall the printer drivers as well.  I am able to print from Word, however I can't print from internet.  I get this message: "there was an internal error and Internet Explorer is unable to print this document." (Internet Explore 11) I downloaded pint and Scan Doctor 4.2 and made 'issues of difficulty printing' and all checks very well.  In my view, that the problem is that I can't solve my printer because it has a warning sign in my area "devices and printers".  When I run the troubleshooter, it is said that it cannot identify the problem.

  Thank you

  Deflace

  Thanks for your response, Deflace.

  Understand that you have reinstalled the software.

  For troubleshooting further, could remove you & reinstall the driver software according to the Guide to ensure that the software is installed correctly.

  Please help make sure that you get the latest Firrmware and update by the link as well.

• CM750A: OfficeJet HP 8600 PRO print head cannot be aligned

  My printer start pages to print, which are unreadable (see attachment). I did several times print head align, but it doesn't help.

  You can see the test page printed, but also problems printing on pictures in my dropbox: https://www.dropbox.com/sh/j9jvhkmxk4ctlhj/AACZKQm_3IVi9ZJ2XhdIT2cva?dl=0

  No idea what this might be and how can I solve this problem?

  Thank you, Vlad.

  Thank you for your advice, but I solved the problem as follows:

  • IT specialis, I have many different features (mostrly interactive and interactive material), but I also have an old printer HP OfficeJet Pro 8600.
  • I checked and found that the two printers (Office Jet 8600 8600 OfficeJet Pro Plus and Pro) replacebale print head.
  • So I had a good opportunity to test my hypothesis, that the print head could cause the problem.
  • I removed the print head with kartridges to the printer that are not aligned.
  • I removed the print head of my old printer work and install in that cannot be aligned.
  • After that is was lined up well - IT WORKS!
  • The printhead with problematic printer cartridges has been installed in the old printer and I handled a bit with the cartridges...
  • After several attempts, it also works.

  After these steps, the two printers work and the problem is solved.

  My conclusion is this: the old print head problem to align it. For those who do not have a secod printer, it might be a good idea to buy just a printhead for replacament - hereby is a HP article on the printhead part number, as well as on the procedure: http://support.hp.com/us-en/document/c02871867

  Hope this might help someone else,

  Vlad (Liatoss).

• : Officejet Pro printer Officejet Pro 6230 6230

  I need to replace the ink cartridges, and the instructions that came with the printer do not explain how.

  I not sure how to open the printer to get the cartridges.

  This information will be included in the new cartridges?

  @popoo

  The following document explains the procedure - and provides a video too:

  Cartridges for HP Officejet Pro 6230 x Series

  Printer:

  Printer HP Officejet Pro 6230

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  My answer-click accept as Solution to help others find answers.

• OfficeJet 6500: Print head cleaning Cycle - why not choose a color?

  I'm having a problem with a single color (magenta) print does not correctly. I've had problems before with black. Why the prinhead cleaning cycle does not allow the selection of a single color for cleaning? Why should I lose the other colors of ink when there is only one that needs to be cleaned? I know that HP wants to sell ink, but be reasonable! That I had problems that appear only after you HAVE installed a new ink tank. And it has not shown using a cartridge to power after best-use-by-date. My guess is that if the ink cartridges are not stored properly the use-by-date means nothing.

  There are a few components of the automatic cleaning cycles.  There are a set of wiper rubber that moved across the printhead to wipe or scrape debris from the print head.  All wiping little ink is spit of each nozzle to lubricate the wiper and help clear the clogged nozzles. The wiper is built on a unique sled with a motor that moves the wipers back and forth.  Allowing single color cleaning would require a much more complicated mechanical system, with four distinct and motors wipers to control.  (The wipers should be dedicated for each color.  She would cause the nozzle clogging if the black ink is allowed to mix with the color and would cause if different colors used the same color mixing wiper.)

  Similarly, for your Officejet 6500, there is a pump system for a more energetic cleaning or for initial priming of printhead.  If it was designed for a single use of color, then a more complicated system, with four independent pumps and controls.

  A Mater of reliability and economics, it is not practical to have separated in level printers cleaning cycles.

• HP officejet pro 8610: hp officejet pro printer

  I try to print on my hp officejet pro 8610 and it keeps printing a lot of pages with weird symbols at the top of the page. When I bought the printer, I had another computer, on which I feel but I switched computers. was I suppose to do something between the evolution of computers. Can anyone help please?

  Hello

  Thank you for using the HP forum.

  Can you download and install the software FULL of printing to HP for your operating system features (Please select the correct operating system):

  http://support.HP.com/us-en/drivers/selfservice/HP-OfficeJet-Pro-8610-e-all-in-one-printer-series/5367603/model/5367606#Z7_3054ICK0K8UDA0AQC11TA930C7

  Once you have downloaded and installed the software, FULL of features, you will be able to print and scan.

  Let us know if that helps.

• OfficeJet 6600: print head

  I'm having with my printhead on my Officejet 6600 I bought a little over a year.  I had to replace the print head twice on my last HP printer.  Is this a common problem with Officejet printers?   I don't know if I should replace the print head or buy another printer from another manufacturer?

  Hello

  OfficeJet 6600 doesn't have a replaceable print head.

  IAM surprised to read in your post that you had replaced the printhead twice.

  Problem with printhead would lead to service the printer.

• Broken tray flap letter on Officejet Pro printer

  Is there anywhere to buy a spare part for the Officejet Pro 8600? I checked the list of replaceable parts of HP for this printer and can't see the part I need.  It is a plastic piece that comes out and stops the book fly away when the book comes out of the printer. It has a flap that you can return to the top, to stop the paper and hold it in place once its print, or you can the flap down. It broke and you don't know where to get a replacement.

  It's called the output tray.

  

• HP 8630 OfficeJet Pro print double-sided on legal size paper

  I just bought a HP OfficeJet Pro 8630 can I print successfully on each Board standard size paper and print on legal paper (from each drawer).  I can print one side, but the driver seems not to allow the duplex legal communication.

  I tried in all stores (I have read on the set 2 only for plain paper, but as I understand it, which applies only to the brilliant vs plain and not of different paper sizes).  In any case, I put my legal paper in Tray 1 and set tray on shift, and the default for tray 2, which seems that it will be a good idea in the future, when we use envelopes, etc.

  But...  The problem that I'm having it is when I go to the printer properties dialog box, if I use duplex printing either on the long edge or short, the legal (and most other choices for paper sizes) have a yellow/triangle exclamation point icon and if I ignore the warning to resolve differences, which either don't let me out of the modal dialog box , or it will just print single-sided anyway.

  I can't find someone else complain that duplex printing legal size does not work, it seems as it should be, but I am at a loss of the configuration of the printer to make it work.  Any ideas?  Success stories?

  I use the latest firmware (FDP1CN1416AR, patch, version 0) and the driver (just downloaded, can't figure out how to get the actual number of installed version)

  Thank you.

  Hello

  The duplex accessory does not support Legal paper size, it is an expected behavior.

  You can perform manual duplex printing using Pages of print options to print the odd pages only, then replace the printed sheets and send other pages even only... the Pages of print options print job is under print options > Layout > advanced.

  You can find the printer specifications below, check the duplexer column according to the specifications of paper output > paper sizes supported:

  http://support.HP.com/us-en/document/c04085902

  Shlomi

• HP officejet 6600: print head seems to be missing, not detected, or incorrectly installed

  does not print hp officejet 6699 - gives message "print head seems to be missing, not detected or installed incorrectly."

  I unplugged the instructions and it does not work.

  I replaced all the cartridges, and it does not work.

  It is more than one year warranty and I do not know where to take.

  I didn't have to buy a new one immediately.  The life expectancy of an all-in-one now is about 2 years old?   Can someone tell me what to try?  Thank you!

  He looking as if the printhead has moved or is not seated correctly in the printer? Try to gently move it and it sits evenly.

  There is an update to the firmware of your device which can help. You can find it here.

  Thank you very much

  Michaele

• OfficeJet 6830: Print head Error Message

  Obviously, there is a problem with many people.  While I remember just when I bought it, and it is even possible that I had for 6 months or a year, this print head thing is a problem, and so far, the machine worked perfectly.  I wouldn't have to go buy another when it's clear, there is a malcunction with the machine that is so widespread.

  I need my printer to my job every day. Which caussed cela and have the rest of you is also the woman who had been his machine for only 30 days?

  mjwhearts

  You will need to contact HP for a replacement.  From a post of Sunshyn2005, contact technical support HP see the following link to create yourself a file number, then call and it can help to expedite the appeal process:

  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  
  File number and phone number are displayed.

• HP Officejet 6600 print head error message

  Recently had an electrical storm and power neighbor hood was off briefly. Though even my printer is plugged into a surge protecter, I now have an error message on my printer that reads...

  "Missing or faulty print head".

  ceyan, magenta, yellow, black

  the print head seems to be mjssing, not detected, incorrectly installed, or incompatible"

  Before the storm, I had installed 2 new ink cartridges. My troubleshooting efforts consisted of unplug the printer from the power source and plug back and removing ink cartridges / resettlement. I always get the error message "printhead".

  Hello

  I think you did everything I would have tried.

  Even if unplug you the printer, I wonder did you leave it unplugged for more than 15 seconds.  See the link

  http://support.HP.com/us-en/document/c03750651

  If this does not resolve the problem then I think it would be appropriate contact HP because this printer is probably still under warranty.

  Hope this helps somehow.

• USB ports no longer works after L7680 OfficeJet Pro printer installed...

  I am running Windows XP Pro SP3.  Before you load the printer all my ports worked (4 on the monitor, 2 on the front of the PC).  Once I'm installing all of them stop working.  The only option is to work with one on the front of the printer.   I am able to get my Western Digital HD to work on the USB port printer, but this one is fickle and only works sometimes (I have to restart to operate when it gives out).  I'm not able to use on the printer port USB flash drives. I f the usb port on the printer does not work, so I have no options.  I tried with a powered hub and it works at all.

  I was chatting with representatives of HP without result. If a HUB on the printer does not work it is a useless tool for me.  I need one that has no readers, etc.  Is this a reason to return to the item under warranty?  Or y at - it a way to get this thing to work.

  HP wants to tell me it's Dell.  Dell says it's HP.  I'm so confused and frustrated.

  What I discovered, after about 3 years, the computers are generally obsolete.  My computer was 1.1 ports and the printer connection 2.0.  As see you all new USB components say they are 2.0, but can work with 1.1.  Long story short, after reading this somewhere, I decided that I had to upgrade my ports.  I went to Microcenter (they have an online store as well) and bought a USB 2.0 PCI Card for $11.00.  At opened her top and broke in the new port and everything works well again.  It may not be what you want to hear, but it was all I could do.  I was told all empty printer resources USB and this is why the upgrade was necessary.  Hope this makes some sense to you.

• How to clean a HP all-in-one Officejet 5610 print head?

  I use a HP no. 27 and a HP #22, each one about half full of ink.

  Head cleaning, for normal users, is possible directly in the drivers Windows 7 or any tools provided printer software that is compatible Windows 7.

• Printers HP OfficeJet Pro 7740: cover printer for HP OfficeJet Pro printer 7740

  I intend to buy a HP Office Pro 7740 pinter. I searched for a cover of the printer. The HP Web site lists the maximum dimensions as 23 "wide X 28.06" X 15.10 depth"high."  But also list size 23 "wide X 18,38" depth X 15,10 ". What size would I go? Looking for a cover for no maximum dimensions is difficult. Thank you for your kind attention.

  Hello

  It depends on how you wish to cover. "" "" "You can see the dimensions maximum b as 23" wide X 28.06 "depth X 15.10 ' top and (b) of normal dimensions as 23" wide X 18.38 "depth X 15.10 ' high.

  (a) when printring, you must extend to output tray (s)

  (b) not in service, for storage.

  Kind regards.