operation of the switch /switchover? without DataGuardbroker

Similar Questions

• Debug mode breaks to the switch, break, without breaking points statement

  Hello

  IAM using Labwindows CVI9.

  IAM simulating a GUI, when my application is run in Debugmode, my app breaks to break switch statements

  even if I did not break points.

  I would be grateful if someone gives suggestions about this

  Thank you & best regards

  Suresh

  Hello

  previously, I've added a few variables in the Watch window to monitor when I set break points.

  Now, I have removed all the variables in the Watch window.

  Now, the application is not breaking up.

  Thanks a lot buddy.

  Concerning

  Suresh

• Can I configure NISE with a switch of party - if the switch is not installed?

  I've never used NOR Switch before Executive - we hope to use it on a new project.

  We do not have equipment at the moment - we will use a Pickering 40-540-021 '132 x 4' switch.

  I would like to configure NI Switch Executive before Pickering delivered cards, is it possible? I get an error when I create the NI Switch Executive virtual device. Seems that MAX is trying to communicate with the switch card before allowing me to configure routes/exclusions/groups etc..

  Here's what I've done so far:

  -Install the drivers of Pickering.

  -To the MAX (v5) I have setup a session driver IVI and logical name.

  When I try to create a new NI Switch Executive peripheral virtual, I add the logical name of the switch, click [next] and get the NISE error...

  "An error occurred so they were trying to access the devices PROJECTSWITCH. The primary error: unknown status code (Hex 0xBFFA400C).

  I see that a virtual device is created with no logical switch assigned. I get the error even if I try and add a logical switch manually to the virtual device NISE.

  Is it because the switch Board is not available for the system? Can I configure the routing/groups/exclusions without the device being mounted physically switch?

  Thank you

  Alan

  Alan.

  
  Seems that MAX is trying to communicate with the switch card before allowing me to configure routes/exclusions/groups etc..

  This should be the expected behavior. NEITHER Switch Executive tries to communicate with the instrument before allowing you to configure routes to ensure that there is no problem that would affect the operation of the Switch Executive. In your case the pilot trying to communicate with a non-existent device.

  I would like to configure NI Switch Executive before Pickering delivered cards, is it possible? Can I configure the routing/groups/exclusions without the device being mounted physically switch?

  It is possible that all compatible IVI devices should have the ability to simulate.

  It seems that you have configured your session of IVI driver incorrectly for a simulated device. I try and make sure that in the session driver, under the 'Général' tab, select the drop down menu to "Simulate with" and select 'Specific driver' and then click 'Save the IVI Configuration'. This will return the Pickering driver selected in the 'software' tab and simulate a device. This should allow you to create a virtual device NI Switch Executive and develop and test the code on the simulated instruments.

  I would like to know if you have any other questions.

• Re: Reinstalling operating system on Satellite A100 without deleting the other existing partition

  Hi all

  I have a Satellite A100-912 and have not reinstalled the operating system (Windows XP) for several years, but now I think that my laptop works well below par. I have my product recovery CD (disk recovery) and it will use for the re-installation.

  I have three partitions on the HARD disk (c, d and e, respectively).

  I was wandering if it would be possible to reinstall (get as long as the factory) my operating system on the c partition without erasing the data (for example my files) on partitions d and e.

  I did this on a Toshiba Satellite L10 using suggestions in this forum, but I don't know how to do it on my own. Is the user interface for the recovery/re-resettlement is not the same thing, so I'm afraid to lose my data if I proceed with the re-install without knowing what to do.

  Could you please say on how to make the re-installation of operating system only on the c partition without deleting (data on) other existing partitions.

  Thank you!

  > I was wandering if it would be possible to reinstall (get as long as the factory) my operating system on the c partition without erasing the data (for example my files) on partitions d and e.

  No, this is not possible. The recovery disk would format the whole HARD drive and therefore the partitions created on the HARD drive would be so removed.
  I recommend you to create a backup of the files before starting the recovery procedure.

• How to get disabled login user (without password) at startup, so NOT to SHOW at all and so after the switch, go to desktop directly

  Vista Ultimate 64-bit

  How to get disabled login user (without password) at startup, so NOT to SHOW it to all (and needed clicked) and so after the switch, go to desktop directly?

  Also after inactivity, how to not go to sleep mode and press "power on" to bring back?

  Hello

  If you want to start directly on the desktop?

  How to automatically connect at startup in Vista
  http://www.Vistax64.com/tutorials/66966-logon-automatically.html

  Or

  How to make Vista require a user name and password when connecting
  http://www.Vistax64.com/tutorials/89812-logon-username-password.html

  =========================================

  Start - Control Panel - Power Options - upper left - require a password on wake up
  tick her do not require a password - save the changes.

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• How to start Firefox in Mode safe on Windows 8 directly from the Start Menu without switching to normal startup?

  Y at - it an option to start the firefox safe without having to open the firefox I have normal mode

  In Windows 7, there is an option to start Firefox in Mode safe in the Mozilla Firefox Menu

  You can start Firefox in Mode safe in two ways

  1. Hold the SHIFT key while double clicking on the Firefox icon in your desktop
  2. Press Windows key + R (open the command run) and type firefox-safe-mode

• Using the FN keys without flash cards

  Hello everyone

  I wonder if its possible to use the FN keys without toshiba flash cards on the top of the screen and therefore without having to install the value-added package?

  Some FN keys like brightness, mute, switch the display and sleep work without VAP
  but I also enabled WiFi, touchpad switch, mode switching power, buttons, which do not zoom

  Yet once, I don't want this utility to flash, still running cards and consumption of ram

  As far as I know something like this is not possible and if you have FN feature flash card utility must be running in the background.
  This along with the consumption of RAM is funny to me because if you turn it off you won't see any difference in the performance of the computer.

  Maybe you should disable some other background process unnecessary that you don't need.
  If you have the new model laptop with Win7 they have enough RAM for all operations and execution of flash cards will not have much influence on the performance of the computer.

• Two small buttons on the side of the switch just stop working - Tecra M5

  I had this problem before too many and I was told that the way to resolve the issue was a recovery CD, which means losing all my DATA and blabla... The problem is that the two very small buttons on the side of the switch just stop working.

  Just as that. They are always connected as when the laptop is on in standby or hibernation mode if you click on them it restart the machine. We tried something with Toshiba technician before and also their repair without success Center (change the purpose of the button, reinstall the program etc...) The only remedy was still a lot of recovery CD and a replacement of the machine, thank you for that. The sentence is still started. It could be a problem as cookies, just a wild guess or anything else.

  Now, nobody knows how to solve this problem, or had the same problem?
  Thank you. Olivier

  You talk about the presentation of Toshiba and Toshiba Assist buttons. Am I wrong?
  It seems that there might be corrupted registry keys or the common modules stopped working.
  Why? I put t know but perhaps I got a solution
  Try reinstalling the common modules.
  First remove it from the Add & Remove programs. Then restart the laptop and install the downloaded again common modules.

• Best wireless network installation with the switch TP-Link

  Hi all

  Few question numpty maybe, but what follows... We just moved to a new (larger) home with thick walls and I want to set up a new wireless network.

  The current installation is:

  Fiber cable entering the House in the basement and connected the modem to the service provider that provides 150 mb internet. I changed the capacity wireless on the ISP's modem and connecting an airport extreme (2014 model) via the LAN to the modem. The extreme is in the office but on the 3rd floor is having connection problems than you can imagine. All rooms have access points CAT5e who all meet in the basement. I have two spare Aiport express and two Apple TV that I would use. Also I bought a TP-LINK 1000mbps (16 channels) Network Switch.

  Could someone please tell how the best set-up of my home network. For example, the Airport Express to the 3rd floor connected to the switch (wired) network or to an extreme in the Office? Apple TV also connected to the network switch?

  I would like to end up with a solid wireless network that passes without problem from extreme to Express necessary each time you walk and you want to use an Apple TV for television on the ground floor and one in our room.

  Many thanks and apologies once more for this very basic question... I have expanded my front (extreme Express) wireless network but just don't know how best to use the switch.

  Thank you

  The simplest up set... which is almost always the best game in place... would be to connect the switch 16 ports to the modem/router and then connect devices to the switch. In other words, if your modem/router has 16 + Ethernet ports, the simplest network configuration would be to plug as many devices as possible directly to the modem/router.

  Other variants are possible, for example, the network might look like this:

  Internet > Modem/Router > AirPort Extreme > switch > devices... or, you can connect certain devices to ports Ethernet on the AirPort Extreme and some to the ports on the switch.  One thing to keep in mind however... If there is a problem... Troubleshooting may not be easy since it will be difficult to know where the problem actually lies.  Much easier to all have, or of possible devices, connect to the switch.

  Unfortunately, the AirPort Express devices will be of real bottlenecks on your network.  These devices are notoriously slow as well as wireless, and even if they work well, the speed will be does not exceed 100 Mbps... since it's the speed of the port to the AirPort Express.  In fact, I expect each Express to provide a wireless signal in the range of 50-60 Mbps.

  Another thing to keep in mind of the wireless network is that Macs will usually a good work of tilting automatically to the point of wireless to the other as moving from one place to the other in the House... but the iPhones, iPads, PCs, and other mobile devices will do that very well... If they do at all.

  So with these devices, you will need to get used to temporarily disable the WiFi on the device and the device when you move in one region to the other, and then turn WiFi on must generally then pick up the signal from a nearby wireless access point.

• How to install Vista from the recovery disk without defining partitions?

  Hello

  I have my recovery disk and I have installed a new 320 gb HHD.
  When I installed the recovery disc, it re done the 160 GB partitions in each (2 partitions more the 1 recovery partition)...

  But I want to dual boot with XP pro because of software problems and I prefer it sometimes...
  I redid my scores, 1 - 51 GB for XP pro(32bit), 2nd - 51 GB for vista (32 gb) and the 3rd - 210 gb is for storage

  How to install with Toshiba vista o/s and stuff that comes with it on the recovery disc, immediately to the 2nd partition without affecting how I configure the hard drive...

  I have about 100 GB of photos, music, and cam vids on storage, with nowhere to put them, so I can't risk, because some are copy only (so it might be a good idea to let me know how I save this s on my storage spread in the DVD please)

  If I can t, then can some1 please tell me how to get my Toshiba OEM vista off this recovery disk or a link for me?

  Hope all this makes sense lol... Thank you
  Shane

  If you have so much important material best save is to buy an external HARD drive and copy all this stuff here. I recommend buying the small 2.5 external HDD and when necessary, you can take with you and connect to any computer, if you want to view or copy this file. External hard discs connected to other computers with a supplied USB cable.

  Return to your partitions.
  When you use the original Toshiba DVD facilities, you will have 3 partitions.
  WinRE - partition and it belongs to the Vista operating system. This partition is not visible, and this isn't some sort of Toshiba recovery partition
  -C for Vista partition
  Or-d/E to the DATA in the partition. This partition is recorded recovery image in the folder called HDDRecovery
  I don't know what model of laptop you have, but this configuration is on all new Toshiba laptops shipped WITHOUT recovery media.

  Using Toshiba recovery media, you will be able to get exactly mentioned structure of the partitions. Support to recovery facilities using you WILL NOT be able to install Vista on the second partition.

  So if you want to have the dual boot with Windows XP Home edition, you can do following:
  -At first, you are going to install Vista with support of recovery and on the second partition, you are going to install your version of Windows XP Home edition
  -At first you will be installing WXP and then you can install Vista on the second partition, but you must use the Microsoft facilities drive. Recovery media can not be used.

  That's all I can say from my experience with such things.

• OK to mix 'of connection to the switch"and"close relay switch?

  Hi all

  I'm developing a test sequence using the card multiplexer 2527 to the track signals.  To configure the card, I use DAQmx switch functions.  In my application, I have a Subvi routine that imports the data from a spreadsheet Setup and run a loop for to set the configuration for each step (each iteration of the loop contains the channel for 2527 card information).  The topology is set on the first iteration, as well as the configuration of the path to the first string.

  My concern is this: I need to close the extra channels/relays without changing the topology or resetting the device.  In the first round, I use "connection to the switch" function to set the initial path, (ch0 to com0 for example).  Then in subsequent iterations of the loop, I use "Relay close switch" function to close the additional channels individually (for example k2).  In the end, when the measure is taken, both ch0 ch2 must be closed and routed to com0.  This implementation is so sure, or am I somehow to make the adjustments to the initial loop?

  I would like to test this with the hardware, but it is not yet available.

  Also, I realize that I could use independent topology and configure all relays individually for each step, but I hope that my approach will be easier and safer.

  Please notify.  Thank you.

  GSinMN

  Hello GSinMN,

  It's OK to mix 'of connection to the switch"and"Close relay switch"If you understand what's happening below. "Switch Connect" connects two channels by closing a path of relay between the channels, then "Close relay switch" can be used to change the State of the individual relays. If you are not careful you can mess up your connection by activating / deactivating relays that are part of the route connecting your channels.

  "Also, I realize that I could use independent topology and configure all relays individually for each step, but I hope that my approach will be easier and safer."

  I would recommend the topology independent if you want to stick with connections to channels only. http://zone.NI.com/reference/en-XX/help/375472G-01/switch/2527_independent/

  Initial connection:

  CH0-> pcom0

  pcom0plus-> icom0plus

  pcom0minus-> icom0minus

  icom0-> com0

  In each future iteration just connect to the next to pcom0 channel (which will be indirectly connect it to com0):

  CH1-> pcom0

  CH2-> pcom0

  ...

  ...

  Jarrod

• HP DV7-3063cl laptop PC: what is the maximum temperature for safe operation of the DV7 3063 cl with the upgrade of the 640 M CPU?

  I have recently restored a HP DV7 3063 cl laptop that died a hot mother (MB). I replaced the MB with a new Board of Directors of HP when the price has been reduced to $100, updated the CPU with an announced as new AMD 640 M and applied Arctic Silver on CPU and graphics chips. I put in 4 G memory cool, got the computer to work and installed Windows 10.

  The computer seems to run very hot and stopped twice from overheating during its first period of 2 weeks when it there was not a lot of calculating, fan was run at top speed at all times, and the laptop was high to allow good airflow below.

  According to the program of the Open Hardware Monitor, the CPU had reached 97-99 C a few times. I bought support cooling a player and that seems to help a lot, dropping the temperature to 20 ° C.

  What is the maximum temperature for safe operation of the DV7 with the upgrade of the 640 M CPU?

  Anything more than 90 c is too hot. You can specify the processor and the motherboard you have installed?

  Also if this from the Manual:

  Thermal paste is used on 1 CPU and heat sink section 2 that the services it. Thermal pads are used on the chip Northbridge 3 and 4, the graphical subsystem chip 5 contact Northbridge and graphics/heatsink contact 6. Thermal material replacement is included with all kits of spare parts of processor, heatsink and system board.

  So unless you have changed the cooling system to heat composed on the chip graphic you should have used a thermal buffer. Without the pad, it may leave just a small hallway and destroy the cooling properties. You can use a shim in copper or other piece of something metal to fill the void, but if you just put the heat sink down on the video chip you won't get optimal even with thermal cooling paste.

• Update the Configuration of the switch switch 2.1 Executive to 3.5

  Hello world

  I tried the switch 2.1 update Executive to 3.5 and have known, that my configurations have stoppped working. To me, it looks like 3.5 dislikes my IVI configuration for switching modules.

  The function check in MAX tells me that the PXI cards are not available. The first page of the configuration of the switch shows no configuration / terminal blocks.

  Because the configuration consists of nine matrix with lots of report cards, I would really appreciate a way to properly import the old configurations (xml files are available)

  Any ideas?

  See you soon

  Oli

  Hi Oli,

  Yes, there was a major change in the Switch Executive 3.5 - it now uses for switching NI DAQmx calls material. There is a KB document the upgrade process a simulated configuration from an earlier version, but of course, you can try the steps that make sense, too:

  Import of NI Switch Executive 3.0 and previous virtual devices in OR Switch Executive 3.5 and later versions

  http://digital.NI.com/public.nsf/allkb/1D1099A85B156FA68625778500787444

  However, I have noticed that the KB Editor uses a configuration file to .txt instead of the .xml you have. I see two options here: first of all, if you have even an operating system with Switch Executive 2.1, you could probably export settings in the form of text or you can try to modify the .xml file manually to resemble the layout of the text (probably a lot of work, you would have to learn the structure of the text by trial and error using newly created Switch E.g. 3.5 configurations...)

  Best regards

  Sebastian

• I/o current or voltage check with the switching matrix

  Hi all

  I want to use a switching matrix to test current and voltage of a control cabinet. For this, I have a voltage of the injector, injector current, a voltage measurement and measurement of currents from one side of the matrix (side line) and a 20 lines by I / O test. Is there a way to check (with a hardware or software solution) that we are ready for a test voltage or current in automatic mode.
  The ideal would be to have a physical key indicating that we are testing the right card, but if the operator uses the wrong card, I would check it is not injected + 24V-on entry to an entry card 0-20mA current.

  I wish you turns me on!

  Best regards

  Vincent

  Vincent,

  Some approaches for you to consider:

  1 Add a resistor or a few resistors to each card.  Measure the resistance before applying all power to the i/o lines.  The code of the resistance (s) to identify the class of Council (current or voltage) and rank (if applicable).  Simple jumper on the unused pins of the connector can also be used.

  2 measure the input impedance (or at least the resistive component) before turning the power on.  An input voltage device probably has a high input impedance while the current input device has a low input impedance. It could detect and reject some devices with resistance to entry incorrect installed.

  3. use a camera to determine which device is connected.  (This should satisfy your request to be informed!)

  4. you can replace the operator with a robot, but the robot would still need to use something like 1, 2 or 3 to identify the boards.

  5. use edge configurations physically incompatible connectors/card so that the cannobe Board connected to the tester bad.

  Lynn

• How to divide the source file without losing labels

  Hello

  I wonder how I could split my file source into two (or more) without losing the tags...

  Hello again, Wolfgang!

  OK, now I understand! However, I fear that there is no import in CVI mechanism, so that you can move the tags to another folder, other than doing this manually.

  However, it would be possible to realize a work around. Since you already have this information in your file of CFS (line Tags field), you can manually copy - paste on the line numbers the new file containing the source code you cut in half of the old file. A few steps:

  1. Either your source code file containing a.c source tags.
  2. Make a copy of a.c (e.g., British Colombia) and add b.c to the project.
  3. In your CFS file, copy - paste the field line Tags of a.c to the wire to the corresponding entry of the BC.
  4. Return to CVI, ensuring that the source code and the source of British Colombia tags are a perfect clone of a.c.
  5. Make the required changes to the a.c and b.c, such as the final result is the logical split of the original file. When you change a source file lines, source tags are also moved to the source editor.
  6. The end result is the code split between a.c and British Colombia, while keeping the corresponding position of the source tags.

  I am aware that there is work involved in the execution of these operations, but the result should be your result.

  I hope this helps, Wolfgang!