Operation Timed out - vSphere API

Similar Questions

• vSphere high availability 'Élection' fails at 99% 'operation timed out' to 1 of the 2 hosts

  Hello

  We had a system with 1 host ESXi 5.1 with local disks.

  Now, we install redundancy by adding a 5.5 U2 ESXi host and a device of vCenter 5.5.

  After having installed and any addition to vcenter, we went the ESXi 5.1 to 5.5 U2 ESXi. The SAN works correctly (vMotion works on the own NETWORK card).

  Now, if I try to activate the high availability, both servers will install the HA Agent and start "Election".

  All the warehouses of data (4) on the SAN are chosen for the HA heartbeat, response of isolation is "keep it turned on" by default.

  A server will always be this process done, and the other will keep "elect" until it reaches 100% and errors on the operation "election timed out.

  I've seen this problem on both servers, so I think that the 'master' elected does not have the problem, only the "slave".

  I have checked these items and executed, but not worked:

  VMware KB: Reconfiguration HA (FDM) on a cluster fails with the error: operation timed out

  -The services were running

  VMware KB: Configuration HA in VMware vCenter Server 5.x does not work, error: Operation Timed out

  -All the MTU has been set at 1500

  VMware KB: VMware High Availability Configuration fails with the error: unable to complete the configuration of the ag of HA...

  -the default gateway is not the same on the two hosts, but I fixed that. There is no itinerary changes. HA the setting is "leave power." After correction and deactivation/reactivation HA, the problem is always the same.

  VMware KB: Check and reinstall the correct version of the VMware vCenter Server agents

  -J' ran "Reinstall ESX host management agents and HA on ESXi" agent of HA, and I checked that it was uninstalled and reinstalled during the reactivation of HA.

  CP /opt/vmware/uninstallers/VMware-fdm-uninstall.sh/tmp
  chmod + x /tmp/VMware-fdm-uninstall.sh
  /tmp/vmware-FDM-uninstall.sh

  I did this for two guests. This fix makes the problem of the election and I was still able to run a HA test successfully, but when after this test, I turned off the 2nd Server (in order to test the PA in the other direction), HA has no failover to 1 and everything remained low. After pressing 'reconfigure HA', the problem of the election appeared again on 1 hosts.

  Here are a few extractions of newspapers:

  -L' availability vSphere HA of that host State became election info 29/11/2014 22:03 192.27.224.138

  -vSphere HA agent is healthy info 29/11/2014 22:02:56 192.27.224.138

  -L' availability vSphere HA of that host State became Master info 29/11/2014 22:02:56 192.27.224.138

  -L' availability vSphere HA of that host State became election info 29/11/2014 22:01:26 192.27.224.138

  -vSphere HA agent is healthy info 29/11/2014 22:01:22 192.27.224.138

  -L' availability vSphere HA of that host State became Master info 29/11/2014 22:01:22 192.27.224.138

  -L' availability vSphere HA of that host State became election info 29/11/2014 22:03:02 192.27.224.139

  -Message "host vSphere HA State" on 192.27.224.139 changes from green to red info 29/11/2014 22:02:58 192.27.224.139

  officer of HA - vSphere for this host has an error: vSphere HA agent may not be properly installed or configured WARNING 29/11/2014 22:02:58 192.27.224.139

  -L' availability vSphere HA of that host State became info error of initialization of 29/11/2014 22:02:58 192.27.224.139

  -L' availability vSphere HA of that host State became election info 29/11/2014 22:00:52 192.27.224.139

  -DSMD3400DG2VD2 data store is selected for the storage heartbeat controlled by the HA agent vSphere on this info host 29/11/2014 22:00:49 192.27.224.139

  -DSMD3400DG2VD1 data store is selected for the storage heartbeat controlled by the HA agent vSphere on this info host 29/11/2014 22:00:49 192.27.224.139

  -Firewall configuration has changed. 'Enable' to rule the fdm value successful.  29/11/2014 info 22:00:45 192.27.224.139

  -L' availability vSphere HA of that host State became not initialized info 29/11/2014 22:00:40 reconfigures vSphere HA 192.27.224.139 root host

  -vSphere HA agent on this host is disabled info 29/11/2014 22:00:40 reconfigures vSphere HA 192.27.224.139 root

  -Reconfigure HA vSphere host 192.27.224.139 operation has timed out.     root of HOSTSERVER01 29/11/2014 22:00:31 29/11/2014 22:00:31 29/11/2014 22:02:51

  -Configuration of vSphere HA 192.27.224.139 operation has timed out.     System HOSTSERVER01 29/11/2014 21:56:42 29/11/2014 21:56:42 29/11/2014 21:58:55

  Can someone give me please with help here?

  Or the extra things that I can check or provide?

  I'm currenty running options.

  Best regards

  Joris

  P.S. I had problems with cold Migration during the implementation of the SAN. After setting up all (vMotion, ESX upgrade), these problems have disappeared.

  When you search for this error, I came to this article: KB VMware: VMware vCenter Server displays the error message: unable to connect to the host

  And this cause could make sense, since the server vCenter changed and IP addressing has been changed during the implementation.

  However, in the file vpxa.cfg, the < hostip > and < serverip > is correct (verified by using https://< hostip > / home).

  Tried this again today, no problem at all.
  

  P.P.S. I have set up several of these systems from scratch in the past without problem (if it is an 'upgrade').

  OK, so the problem is solved.

  I contacted Dell Pro Support (OEM offering the license) and they checked the logs (fdm.log) and found that the default IP gateway could not be reached.

  The default gateway is the ip address by default host isolation, used by HA.

  Because it is an isolated production system, the front door provided proved only for future purposes.

  Now, I've changed the default gateway address of management on the switch plugged into both hosts, namely the ping requests.

  This solved any problem.

• Game get unresponsive, a communication error has occurred: Operation Timed out

  A communication error has occurred: "Operation timed out".

  The Web server may be down, too busy or other problems preventing him from answering. You can try again at a later date.

  For assistance, contact your network support team. That's what I get when I try to access a game I play. Worked fine when I stopped last night, but all day was like that, everything is fine.

  Hello

  ·          Game in which you try to read?

  ·          You play this game online?

  I would say also, please contact game support to check their end technical issues.

• Get error 118 (net::ERR_CONNECTION_TIMED_OUT): the operation timed out when opening applications on Facebook

  I need help for my this error error 118 (net::ERR_CONNECTION_TIMED_OUT): the operation timed out

  It's my app from facebook

  Hi Muhammadarif,

  1. the problem occurs only in facebook?
  2. what web browser do you use?

  This is a known error in Google chrome. If you are using Google chrome then I suggest you post in the forums of Google chrome.
  http://productforums.Google.com/d/Forum/chrome

  If the problem only occurs in facebook, then I suggest you to contact facebook support.
  http://www.Facebook.com/help/

  Hope this information is helpful and let us know if you need more assistance. We will be happy to help.

• 'Operation timed out', while protecting a virtual machine

  When you try to configure protection on a virtual machine in 4.1 SRM and every time I do it fails with the error 'Operation timed out' and I see the following error message in the log of Site Recovery Manager:

  2010-09-21 14:07:29.502 04584 verbose "PropertyProvider" ASSIGN RecordOp: info.error, com.vmware.vcDr.ReplicationGroup.AddVmTask - 153

  2010-09-21 14:07:29.502 04584 'com.vmware.vcDr.ReplicationGroup.AddVmTask - Task' verbose Error value {(vim.fault.Timedout)

  dynamicType = & lt; unset & gt;

  faultCause = (vmodl. NULL in MethodFault),

  MSG = ""

  }

  2010-09-21 14:07:29.502 04584 verbose "PropertyProvider" ASSIGN RecordOp: info.completeTime, com.vmware.vcDr.ReplicationGroup.AddVmTask - 153

  2010-09-21 14:07:29.502 04584 info 'com.vmware.vcDr.ReplicationGroup.AddVmTask - Task' State of the error value

  2010-09-21 14:07:29.502 04584 verbose "PropertyProvider" ASSIGN RecordOp: info.state, com.vmware.vcDr.ReplicationGroup.AddVmTask - 153

  2010-09-21 14:07:29.502 04584 verbose "PropertyProvider" RecordOp REMOVE: addVmsTaskList, group-4425'

  Someone at - it no indication on what this alarm tells me and how to fix?

  Thank you.

  V.

  I saw this problem after repairing the installation of SRM. Restart both servers SRM has solved the problem.

  In your case, this is the new installation or did you 'fix' recently?

• 'Operation Timed Out' when cloning a VM

  Hello

  I'm trying to clone a virtual machine through virtual Center and I get the following error after only a few seconds.

  Impossible to duplicate * NAME * server has expired.

  ESXI 4.1.

  VSphere Server 4.1.0

  I am cloning to the same host

  Cloning of virtual computer works fine.

  Would really appriecate any help/troubleshooting advice, not even sure what log file for check but below is a part of the file server VCentre {vpxd-974 Journal} log log if it helps.

  Thank you

  2012-03-16 20:04:44.574 08068 verbose 'App'] [VpxdTaskInfoPublisher] processing object update 0 filter 0

  [16-03-2012 20:04:44.574 08068 verbose "App"] [VpxdTaskInfoPublisher] update for prop info.completeTime

  [16-03-2012 20:04:44.574 08068 verbose "App"] [VpxdTaskInfoPublisher] UpdateTaskInfo for channel task-25392

  [16-03-2012 20:04:44.574 08068 verbose "App"] [TaskInfoChannel::NotifyWaiters] Notified for _infoVersion: 4; task: task-25392

  [16-03-2012 20:04:44.574 08068 verbose "App"] [TaskInfoChannel::SetDisconnected] task: task-25392

  [16-03-2012 20:04:44.574 08068 verbose "App"] [TaskInfoPublisher::RemoveChannel] Channel (task-25392) removed for task: task-25392

  [16-03-2012 20:04:44.574 08068 verbose "App"] [VpxdTaskInfoPublisher] Disconnected

  [16-03-2012 20:04:44.574 08384 verbose "App"] TaskInfoChannel destroyed for task-25392

  [16-03-2012 08700 error "App" opID = 07130DD4-000004DF 20:04:44.574] [clone] (SERVER1) Unexpected exception (vim.fault.Timedout) over clone. Abandonment.

  [16-03-2012 08700 WARNING opID "App" = 07130DD4-000004DF 20:04:44.583] [JrnlFilePersistenceProvider] Got EOF when reading file

  [16-03-2012 08700 verbose opID "App" = 07130DD4-000004DF 20:04:44.598] [JrnlFilePersistenceProvider::DeleteJournal] Removal of C:\ProgramData\VMware\VMware VirtualCenter\journal\1331928251.240.

  [16-03-2012 08700 info "App" opID = 07130DD4-000004DF 20:04:44.598] [VpxdVmprovXaction] From the log restore

  [16-03-2012 08700 info "App" opID = 07130DD4-000004DF 20:04:44.598] [VpxdVmprovXAction] UndoCreateSnapshot... vm: vim. VirtualMachine:vm - 345, name of the snapshot: clone-temp-1331928251840724

  [16-03-2012 08700 error "App" opID = 07130DD4-000004DF 20:04:44.599] [VpxdVmprovXAction] UndoCreateSnapshot failedto find the snapshot that he was supposed to remove

  [16-03-2012 08700 verbose opID "App" = 07130DD4-000004DF 20:04:44.599] [VpxdVmprovXaction] An std (vmodl.fault.SystemError) exception in treatment entered paper (op = 7), the entry is ignored

  [16-03-2012 08700 info "App" opID = 07130DD4-000004DF 20:04:44.599] [VpxdVmprovXaction] Made available VM transaction cancellation

  [16-03-2012 08700 verbose opID "App" = 07130DD4-000004DF 20:04:44.599] [vm.clone] Unexpected exception when cloning a vm: /vpx/vm/#345 /.

  [16-03-2012 08700 verbose opID "App" = 07130DD4-000004DF 20:04:44.599] [VpxdResMgr] Unreserving

  [16-03-2012 08700 verbose opID "App" = 07130DD4-000004DF 20:04:44.599] [VpxdResMgr] RESV Spec:

  (host - 361:3, 1)

  (host - 361:8, 0)

  (host - 366:3, 1)

  (host - 366:8, 0)

  [16-03-2012 08700 error "App" opID = 07130DD4-000004DF 20:04:44.599] [VpxdVmprov] Clone failed: vim.fault.Timedout

  [16-03-2012 08700 error "App" opID = 07130DD4-000004DF 20:04:44.599] vim.fault.Timedout

  -End of newspapers in memory-

  [16-03-2012 08700 info "App" opID = 07130DD4-000004DF 20:04:44.603] [VpxLRO] - FINISH special 47187 - vm-345 - vim. VirtualMachine.clone--481DABDF-D6BC-4F17-B43A-80AB476FB60D(84215248-DBF9-4769-ABB6-59796EA66029)

  [16-03-2012 08700 info "App" opID = 07130DD4-000004DF 20:04:44.603] [VpxLRO] - ERROR task-47187 - vm-345 - vim. VirtualMachine.clone: vim.fault.Timedout:

  Result:

  {(vim.fault.Timedout)

  dynamicType = < unset >

  faultCause = (vmodl. NULL in MethodFault),

  MSG = 'Operation timed.' out,

  }

  Args:

  The ARG file:

  ' vim. record: Group-v447'

  The ARG name:

  "New Virtual Machine.

  ARG spec:

  {(vim.vm.CloneSpec)

  dynamicType = < unset >

  location = {(vim.vm.RelocateSpec)

  dynamicType = < unset >

  data store = ' vim. Datastore:datastore - 168',

  diskMoveType = < unset >

  pool = ' vim. ResourcePool:resgroup - 87',

  Host = < unset >

  transform = < unset >

  },

  model = false,

  config = null (vim.vm.ConfigSpec),

  customization = null (vim.vm.customization.Specification),

  powerOn = false,

  snapshot = < unset >,

  }

  Hi kilicool,

  Welcome to the community.

  Have you tried to reboot the VC Server? If Yes

  In turn, before adding the host ESX VCS try to restart the management

  The agent that is running on ESX.

  CLI: service mgmt-vmware restart

  If this does not work I would say adding VC to the host, but I think that the

  above command will help you because it's just VCS

  "Affirmation without discipline is the beginning of delirium."

• Host does not switch into maintenance - Operation Timed Out mode

  Hey all.

  I'm putting one of my hosts in the mode of maintenance and get an 'Operation Timed' error Out. All virtual machines have been moved outside the host so I know that's not a problem "CD in the drive.

  I tried to do this in VC and the command line using vimsh - n EI/hostsvc/maintenance_mode_enter

  When I run the command line, here is the result:

  # vimsh-e - n/hostsvc/maintenance_mode_enter

  File not found.

  -2008-12-13 16:16:35.872 'App' 3076444288 info] current working directory: / usr/lib/vmware/hostd

  -2008-12-13 16:16:35.874 'BaseLibs' 3076444288 info] HOSTINFO: see Intel CPU, numCoresPerCPU 4, numThreadsPerCore 1.

  -2008-12-13 16:16:35.875 'BaseLibs' 3076444288 info] HOSTINFO: hyperthreading disabled, setting the number of threads by heart at 1.

  -2008-12-13 16:16:35.876 'BaseLibs' 3076444288 info] HOSTINFO: this machine has 2 physical processors and 8 cores total 8 logical processors.

  -2008-12-13 16:16:35.877 'BaseLibs' 3076444288 info] use system libcrypto, version 90709F

  -2008-12-13 16:16:35.878 info 'App' 3076444288] Vmacore::InitSSL: doVersionCheck = true, handshakeTimeoutUs = 120000000

  [- 2008-12-13 16:16:35.905 'BaseLibs' 13552560 attention] - Vmdb_Unset] unknown path: /vmomi/

  ' vim. task: haTask-ha-host - vim.HostSystem.enterMaintenanceMode - 198307'

  Something tells me that the "file not found" is not a good thing. If you can think of to try please let me know.

  TIA

  Post edited by: kac2

  I changed the first [to one - for purposes of formatting

  Unfortunately, this happens from time to time.  The work around is simply restart the host as it is, and then maintenance.

• Recompose the vmware view 4.6 error "error:-customization operation timed out."

  Hi all

  In my organization I have deployed automated floating pool. Yesterday, I refreshed two offices of problem which is locked with the service account, we have in the organization. The workstations are still locked with the service account after refresh. So I recomposed the two workstations, but the re-composition not is not finally made. The personalization state is there for around 40mins. After that the status is "error:-operation of personalization exceeded.»

  Please help me on this. Why recompose is not done. It occurs usually within 10 minutes.

  Take a look in the composer-journal on the desktop and vCenter, should give you some clues.

  I suspect the AD account or dns/vSwitch port problems.

  Linjo

• personalization operation timed out VMware View 4.5

  I'm quite new to Vmware view and this is my first time setting up, please bare with me.

  I get the above error when trying to automatically create a related pool.

  I also spent review the previous post that says abot ensuring that:

  • DHCP is enable on the master image
  • VMware view agent is installed
  • VMware tools is installed
  • The firewall is disabled

  The new virtual machines are created and when I connect to Vsphere is to see that they connect to the field, receive IP from the DHCP server. But I don't see their name in my DNS.

  I hope to have provided enough information and you will appreciate any help.

  To the first just nslookup query, and check whether or not the host of clones name is resolved. Also select al virtual machines to see the Administrator page and perform a reset and see<--  if="" both="" these="" actions="" resolve="" your="" issue="" then="" it="" was="" due="" to="" a="" minor="" network="" outage="" happened="" during="" the="" provisioning="">

  Otherwise,.

  1. If the DNS server is a server active directory integrated one or not? If this is not the case, check the permission to register for this DNS server.

  2. the question of whether the DNS entry received from the DHCP server to clone is directed to the right DNS server? and same DNS / domain name cannot be resolved vcenter server?

  3. have you used Sysprep customization? If Yes, be aware that the domain setting is not levied custom specification but DNS settings will be taken from custom spec. In this case the definition given in the spec custom DNS should resolve the field added in vcenter configuration Admin display page

• Operation timed out. Cancellation...

  I've had this problem now for 3 versions of DW, more recently, with CS5.5x

  I have changed the settings and increased the Prefs/Site: FTP timeout to 180 seconds. (Verified) 180 seconds via FTP transfer options.

  I use:

  • FTP over SSL/TLS (explicit encryption);
  • port 2121 (on the advice of the host);
  • Authentication (none) - could not get a connection.
  • Passive FTP mode
  • FTP performance optimization is checked.

  I use DW CS5.5 [11.5 construct 5344] on a Mac running 10.6.8.

  I am able to download successfully via FTP, using the FTP Transmit (v 4.1.6) program, so there is something in DW himself that causes this problem.

  Any ideas out there?  I'm going crazy!  My host is unable to understand the question either, and since all the works in the show, it must be a matter of DW.

  Thank you

  Peter

  I am happy to say that my host has been able to solve the problem.

  In case it is beneficial for others, here is their explanation for what was wrong:

  "Our servers use iptables for their firewalls, this is not automatically pick the port assigned to a passive FTP connection when the connection is encrypted." The port range configured on the FTP server for passive mode data channel has not exactly match the range of ports that was explicitly open in the firewall for that purpose, which gives only a 1 in 3 chance to get a passive FTP connection encrypted work. »

• Remove diskgroup failure of vSAN got out '' Operation timed. ''

  We have experienced two incidents of "permanent disk failure" in the last three months, that has happened on two Micron SSD cards on two different hosts (almost all new material in respect of vSAN HCL).   Application of the micron shows that disks are healthy. So far, the only explanation I got from Vmware is ' this seems to have been a temporary hiccup ".

  Right now I can't even remove the defective diskgroup (vSAN is configured as manual disc claiming () , I put this host mode of maintenance, rebooted, it, then tried to remove the "defective" SSD drive, so I can remove the diskgroup, but it still fails with "operation timed out".

  Now I remember, the last time I had this problem of "permanent drive failure", I had to physically remove the SSD card out of the host, then I can remove the diskgroup. I wonder if it's the only way to do it?

  tempted to follow VSAN part 16 - the recovery disc for other uses - CormacHogan.com to erase just the partiton of vSAN now. (all virtual machines are migrated already of this host when I turned it in maintenance mode).

  Now becomes very frustrated with vSAN.

  Thanks Chogan.

  The SR number is 16865002201. I just had a long webex with support Vmware Jesse, it is very useful.

  We tried weapon of wipeout for the 'secret' disk in Vmware, but it also did not work. Finally, we used Micron rssdm application to ensure erased the disc, then rebuilt in the diskgroup.

  Now our vSAN is back to normal.

• ESX Server timed out when I try to enter the license server in the CR

  Hi all

  I have a problem with the addition of two new ESX servers in our virtual Center.

  Let me give you a brief overview:

  We have 5 servers ESX and virtual Center Server.

  All servers are in a single Cluster (Cluster 01)

  Now, we want to use Virtual Desktop Infrastructure and for this reason, we bought another 2 servers (blades).

  I installed from scratch with ESX 3.5 Update 4.

  I did a second Cluster in our VC (Group 02) and add the two.

  I configured the network settings and storage, everything went very well, shoot when I want to point to our license server, whenever I get an error message from our VC. Operation timed out and my settings when not accepted. No matter if I get the IP address or FULL domain name. BUT I can ping our server to ESX Server licenses, so I'm not sure if this is some sort of DNS issue or not.

  Another note: our first 5 ESX servers where ESX Server Standard license.

  Our new ESX servers where an ESX Server VDI license. I used the CD to install ESX normal, because I have not found any VDI install special files.

  I see all licenses in the Administration view in our VC, so I think our license file is not corrupted.

  Things I've done so far:

  Renewal of license, start stop server, esx Server license installed twice from scratch

  I have no more ideas, I hope someone could help me with this problem.

  According to your image, you have 0 agent licenses virtual centre-left to allocate to new hosts.  What might happen, is that the agent is not properly installed on the new servers.  Connect to ESX servers.  Make sure that you can test the virtual Center by domain name server FULL and hostname, not only by intellectual property.  From your RESUME, ping your esx server fqdn and the host name.

  Also, check the file/etc/hosts on your esx server and make sure that the entries are tiny.

  -KjB

  VMware vExpert

• Mainenance mode - operation times out when VMs powered - HA question?

  Hello

  I want to update our two guests to esx server 3.5 with Manager running on vCenter 2.5 update. (Mamaged through the Infrastructure Client 2.5)

  On the two hosts vm is turned on. When I start sanitation on the single host an error occurs (operation timed out). When I set up the answer for the failure to "Power Off and try again" the powers of the host in the broad all VMs and update work.

  My question is: shouldn't the host use HA to turn off the virtual machine, move them to another host and turn it on again? Or vMotion is required for this operation?

  I forgot to ask you one thing, you play with setting HA? (Leave the machine market, stop, stop). This could be a different result!

  Should move the virtual machine automatically with vMotion & DRS

  System engineer

  Zen Systems Sdn Bhd

  Malaysia

  www.no-x.org

• Java.io.ioException: Tunnel Timed out received

  Hello

  We have developed a Java ME application that has been evaluated for fine fonctinner on Blackberry 9000 using the Wifi Interface. Downloaded the application on our server and the application installed on the device using OTA. The cod was signed through Blackberry. Application installs correctly and when it is launched, he's trying to connect to our server by using the HTTP connection. We use the direct TCP with Vodafone (India) APN setting (I tried www, portalnmms and blackberry.net) but with all 3 APNs, the error is the same:

  java.io.IOException: Tunnel Timed Out

  With the URL '; deviceside = true' is specified for a direct TCP connection. Default browser to HTTP is configured for the Internet browser.

  HTTPDemo installed JDE, device samples and it also gives the same error.

  Tried to contact the service provider for the mistake of tunnel... but no help.

  Can someone help pls on this issue? Are there network tools to diagnose problems of tunnel on blackberry?

  Model: Blackberry 8310

  Version: 4.5.0.55 (Platform 2.7.0.68)

  Thank you

  Bennett

  Try the NetworkDiagnostics tool of the RIM. In addition, look at the log of events to see if the right NPP (those that you set in the Options-> advanced-> TCP) is actually used by the operating system - sometimes WAP 2.0 TCP is used instead.

  Another thing you could try is to take the this BlackBerry SIM card and insert it in a non-BlackBerry phone, say, a Nokia. Then you can check if this unit can connect to the Internet and you might also find what NPC he uses.

• Get VPN client to connect, but request timed out when ping

  Hi, I use the router Cisco 837 as my VPN server. I am connected using Cisco VPN Client Version 5. But when I ping the ip of the router, I have request timed out. Here is my configuration:

  Building configuration... Current configuration : 3704 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname michael ! boot-start-marker boot-end-marker ! memory-size iomem 5 no logging console enable secret 5 $1$pZLW$9RZ8afI8QdGRq0ssaEJVu0 ! aaa new-model ! ! aaa authentication login default local aaa authentication login sdm_vpn_xauth_ml_1 local aaa authorization exec default local aaa authorization network sdm_vpn_group_ml_1 local ! aaa session-id common ! resource policy ! ip subnet-zero no ip dhcp use vrf connected ip dhcp excluded-address 192.168.1.1 ! ip dhcp pool michael    network 192.168.1.0 255.255.255.0    default-router 192.168.1.1    dns-server 202.134.0.155 ! ip dhcp pool excluded-address    host 192.168.1.4 255.255.255.0    hardware-address 01c8.d719.957a.b9 ! ! ip cef ip name-server 202.134.0.155 ip name-server 203.130.193.74 vpdn enable ! ! ! ! username michael privilege 15 secret 5 $1$ZJQu$KDigCvYWKkzuzdYHBEY7f. username danny privilege 10 secret 5 $1$BDs.$Ez0u9wY7ywiBzVd1ECX0N/ ! ! ! crypto isakmp policy 1 encr 3des authentication pre-share group 2 crypto isakmp xauth timeout 15 ! crypto isakmp client configuration group michaelvpn key vpnpassword pool SDM_POOL_1 acl 199 netmask 255.255.255.0 ! ! crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac ! crypto dynamic-map SDM_DYNMAP_1 1 set transform-set ESP-3DES-SHA ! ! crypto map SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1 crypto map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1 crypto map SDM_CMAP_1 client configuration address respond crypto map SDM_CMAP_1 65535 ipsec-isakmp dynamic SDM_DYNMAP_1 ! ! ! interface Ethernet0 description $FW_INSIDE$ ip address 192.168.1.1 255.255.255.0 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452 hold-queue 100 out ! interface Ethernet2 no ip address shutdown hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive dsl operating-mode auto pvc 0/35   pppoe-client dial-pool-number 1 ! ! interface FastEthernet1 duplex auto speed auto ! interface FastEthernet2 duplex auto speed auto ! interface FastEthernet3 duplex auto speed auto ! interface FastEthernet4 duplex auto speed auto ! interface Virtual-PPP1 no ip address ! interface Dialer1 description $FW_OUTSIDE$ mtu 1492 ip address negotiated ip nat outside ip virtual-reassembly encapsulation ppp dialer pool 1 ppp chap hostname ispusername ppp chap password 0 isppassword ppp pap sent-username ispusername password 0 isppassword crypto map SDM_CMAP_1 ! ip local pool SDM_POOL_1 192.168.2.1 192.168.2.5 ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 ip http server no ip http secure-server ! ip nat inside source static udp 192.168.1.0 1723 interface Dialer1 1723 ip nat inside source static tcp 192.168.1.4 21 interface Dialer1 21 ip nat inside source route-map SDM_RMAP_1 interface Dialer1 overload ! access-list 1 remark SDM_ACL Category=16 access-list 1 permit 192.0.0.0 0.255.255.255 access-list 102 remark SDM_ACL Category=2 access-list 102 deny   ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 access-list 102 permit ip 192.168.1.0 0.0.0.255 any access-list 199 permit ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 route-map SDM_RMAP_1 permit 1 match ip address 102 ! ! control-plane ! banner motd ^C Authorized Access Only UNAUTHORIZED ACCESS TO THIS DEVICE IS PROHIBITED You must have explicit permission to access this device. All activities performed on this device are logged. Any violations of access policy will result in disciplinary action. ^C ! line con 0 no modem enable line aux 0 line vty 0 4 ! scheduler max-task-time 5000 end
  
  Thank you, anny help will be appreciated.
  			 
  Hi Michael,
  I have been through the newspapers, they are not conclusive and only detrmine that Phase 1 is coming. However according to this error message % SYS-2-BADSHARE: Bad refcount in pak_enqueue, ptr = 81B50AD8, count = 0 we are hiiting a bug on ios. The id of the bug is CSCsl24693 and the solution is to switch to 12.4 (11) XJ.
  Can you re-execute him debugs and send me the detailed results.
  Kind regards
  Aman