Optimization Aironet 1142
Hello
As of today, we moved 2 access points Aironet in our company to allow customers wireless like the macbooks, iphones and other devices. I have installed two access points the same way (although they are on 400meters apart from eachother) and them configured via the web interface.
The basics are
-1 name SSID for both RADIOS (2.4/5)
-Authentication is set to AES/TKIP / mandatory activate WPA V2
-Less-congested frequency
-20 Mhz to 2.4 since 40 mhz doesn't seem possible here
-40 Mhz above on 5 GHz
All the other options I left default.
Let me be clear that no other wifi signals are in the way, clients im test is about 5 metres from the access point and that nothing is really in the way aswell. The firmware seems to be c1140-k9w7 - tar.124 - 21A .JA1
Now, the thing is that it seems to work, however, 2 problems:
(1) every xx minutes of customers seem to be abandoned, that's what I see:
Dot11Radio0, f0cb.a188.3742 reason for the Station Deauthenticating of interface: station has left the BSS
Interface Dot11Radio0, Station f0cb.a188.3742 Associated KEY_MGMT [Wpa2 PSK]
Dot11Radio0, f0cb.a180.f6d3 reason for the Station Deauthenticating of interface: previous authentication is no longer valid
Interface Dot11Radio0, Station b88d.1204.c2bc Reassociated KEY_MGMT [Wpa2 PSK]
(2) the speed (the macbook air of 2011 seems not to connect at 5 ghz), stays around to transmit rates: 104
So my questions are,
(1) what can cause the fall of a customer like that?
(2) it is wise to have the same name for both radios?
(3) I missed something to pick up the pace?
Thanks for any help,
Michiel
Well, you only run wpa2/aes or WPA/Tkip. Don't the installer of your ssid for wpa2/aes or Tkip.
Sent by Cisco Support technique iPad App
Tags: Cisco Wireless
Similar Questions
-
Aironet 1142 in Configuration of the House
One of our customers had problems connecting to their server environment terminal server home wireless. I narrowed down it to their network with wireless at home. An Aironet 1142 was purchased to be placed on their home network to ensure that wireless connectivity will not be a problem in the future.
I'm trying to configuring it to use it, but I am unable to connect to the web interface and I don't have a transfer convenient to access the console cable. It is currently connected directly to a cisco House (not a managed switch) switch typical. I am also connected via ethernet. I confirmed that the WAP Gets an IP address from the DHCP server, but the LED on indicator flashes red, green and amber. Configuration guide mentions it will do that if it cannot reach the area of management, but in a home network I don't know really what it means.
Any help at all would be greatly appreciated. I was tasked to deliver to the customer's home, from 08:00 tomorrow...
-Matt
So, it's a lightweight access point? And you need convert to IOS?
Download an IOS image
Set your ethernet IP 10.0.0.2 comp
Set up the model as the TFTP server using the ethernet interface
Drop IOS image in TFTP folder and rename the file: c1140-k9w7 - tar.default
Connect the turn for the model using ethernet
Turn on the LAP while holding the reset button in
Wait until the light up in red
TURN will download the firmware and reloading
-
I have a 1142 I bought this must be set to factory default so that I can set it up. I am an escape to the boot sequence and I get to the
PA:
command prompt, the instructions to reset that Cisco provides says that I should rename the former config.txt and restart and I will then be able to start my reconfig. The problem is that I can't find a config.txt file in the flash space:
Directory of flash: /.
2 - rwx 260 January 1, 1970 00:04:28 + 00:00 env_vars
3 - rwx 112947 April 1, 2011 15:17:10 + 00:00 event.log
drwx-5 128 1 March 2002 00:01:54 + 00:00 c1140-rcvk9w8-mx
drwx 9 256 1 April 2011 14:30:32 + 00:00 c1140-k9w8 - mx.124 - 21A .JHB1
8 - rwx 5144 1 Mar 2002 00:00:27 + 00:00 private-multiple-fs
I checked in the directories listed above and still found no config.txt. I appreciate any help since I'm stuck and can not go further.
Thank you
Well, you have a lightweight access point that should work with a wireless controller. right?
This can be reset to the default values by using the mode button.
The steps required are (quoting Leo link above):
Step 7 Disconnect power from the access point.
Step 8 Press and hold MODE while you reconnect power to the access point.
Step 9 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
You can forget the other steps. These three steps are the only steps to reset your light AP to the default values.
But why you want to reset the default access point? If you are connecting to a controller of the new image and config is automatically downloaded from the controller.
If you think that what you have is a standalone AP, then no, it isn't. This one is a lightweigt AP. So if you want to convert standalone/standalone AP follow this link:
HTH
Amjad
-
Aironet 1142 standalone, no clients can connect to this topic.
Hello
I have a strange behavior on my standalone 1142, it's been 2 days now. No clients can connect to this topic.
The config has been reset 5 times already, even tried with 3 different versions of IOS and still nothing.
I put this up ever since a few years back now and it worked perfectly.
3 days ago, I changed the PSK, it worked fine for one day and then it happened.
I get the authentication failure of all devices that tried to connect to this topic, I even changed the configuration with no authentication, radio stations are open, the two SSID with no guarantee whatsoever, and even with no encryption I can't connect on it.
Really strange, I was setting up Cisco AP for many years and now I have a black out... I don't know I'm missing something, I can't understand what it is...
Any help about it please?
Thank you
Kyriakos
you have a WLSM?
If not, you should remove the
mobility network-id 3
and the
mobility network-id 1
statements that they are for communication with the WLSM
HTH,
Steve -
Aironet 1142 not broadcasting the SSID
I configured the device manually, not even using quick or Express security configuration then... it's possible that I missed something.
Anyway, here's the problem. Although the SSID is configured as 'AP1', this SSID is not among the networks available on the client computer.
The connection configured in the group policy for the customer, should happen actually automatically, based on the SSID, but because the SSID is not broadcast, connection fails as well.
The Aironet is among the available networks 'Other network' and if I click on "connect" I am asked to enter the SSID-> AP1
Although fashionable, the error message displays (unable to connect to the network, or something to that effect), the laptop * fact * connect once I have close this window. Access to the network is complete and functional - I can ping other hosts, etc...
I would post screenshots, but not knowing what parameter is missing or incorrect, I must print dozens. So here's the sh run out of the AP obtained via telnet (just below). Can someone tell me what is missing? It's a test network so all information is 'real' (nothing has changed for privacy):
Note: I even changed the hostname to "AP1" (it's still LAB1 below) but that has not solved the problem (do not think it would be).
#######################################################################################################
Lab1 #sh run
Building configuration...Current configuration: 2321 bytes
!
version 12.4
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
hostname LAB1
!
Pulse 9 logging console
enable secret 5 $1$ $9EWD kxrbg8KxikRFypOieKiZh.
!
AAA new-model
!
!
AAA rad_eap radius server group
Server 10.0.0.12 ACCT-port auth-port 1812 1813
!
AAA rad_mac radius server group
!
AAA rad_acct radius server group
!
AAA rad_admin radius server group
!
AAA server Ganymede group + tac_admin
!
AAA rad_pmip radius server group
!
RADIUS server AAA dummy group
!
AAA authentication login eap_methods group rad_eap
AAA authentication login mac_methods local
AAA authorization exec default local
AAA accounting network acct_methods power group rad_acct
!
AAA - the id of the joint session
!
!
dot11 syslog
!
dot11 ssid AP1
authentication open eap eap_methods
authentication-key wpa version2 management
!
!
!
062506324F41 Cisco 7 password username
!
!
Bridge IRB
!
!
interface Dot11Radio0
no ip address
no ip route cache
!
encryption ciphers aes - ccm mode
!
SSID AP1
!
gain of antenna 0
local power 2
power customer 2
root of station-role
Bridge-Group 1
Bridge-group subscriber-loop-control 1
Bridge-Group 1 block-unknown-source
No source of bridge-Group 1-learning
unicast bridge-Group 1-floods
Bridge-Group 1 covering-disabled people
!
interface Dot11Radio1
no ip address
no ip route cache
Shutdown
gain of antenna 0
DFS block 3 Strip
channel SFR
root of station-role
Bridge-Group 1
Bridge-group subscriber-loop-control 1
Bridge-Group 1 block-unknown-source
No source of bridge-Group 1-learning
unicast bridge-Group 1-floods
Bridge-Group 1 covering-disabled people
!
interface GigabitEthernet0
no ip address
no ip route cache
automatic duplex
automatic speed
No keepalive
Bridge-Group 1
No source of bridge-Group 1-learning
Bridge-Group 1 covering-disabled people
!
interface BVI1
IP 10.0.0.51 255.0.0.0
no ip route cache
!
default IP gateway - 10.0.0.12
IP http server
no ip http secure server
IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
radius of the IP source-interface BVI1
format of server RADIUS attribute 32 include-in-access-req hour
RADIUS-server host 10.0.0.12 auth-port 1812 acct-port 1813 borders 7 15135A0E07782F2
12E60
RADIUS vsa server send accounting
1 channel ip bridge
!
!
!
Line con 0
line vty 0 4
!
endLAB1. #
You must add the command "guest mode" under the terms of the section. (without the quotes of course)
Sent by Cisco Support technique Android app
-
Need help to set up AP 1142 standalone
Hi all
Need help. I am trying to configure Cisco Aironet 1142 standalone, this access point has been previously connected to WLC and the previous post, I found that we need to delete and reload the AP
private-multiple-fs, c1140-k9w8 - mx.124 - 21A .JHA
Now when I try to configure the IP address for the AP, he is in error:
Ip address of AP1142 #lwapp ap 10.61.1.151 255.255.255.0
ERROR! Command is disabled.
AP1142 #.Current flash content:
AP1142 #dir
Directory of flash: /.2 - rwx 10264 March 1, 2002 01:25:57 + 00:00 private-multiple-fs
3 - rwx 90396 March 1, 2002 01:18:04 + 00:00 event.log
drwx-5 128 1 March 2002 00:12:24 + 00:00 c1140-rcvk9w8-mx
8 - rwx 0 March 1, 2002 01:26:06 + 00:00 config.txt
9 - rwx 337 March 1, 2002 01:18:04 + 00:00 env_varstotal 32385024 bytes (30019584 bytes free)
AP1142 #.Please let me know whatelse is required for the configured in stand-alone mode access point.
Thanks in advance
The image that is on the device's LWAPP, not the autonomous... If you want to use the AP autonoous mode then the image must be W7... It's...
C1140-k9w7 - mx.124 - 21A .JHA not c1140-k9w8 - mx.124 - 21A .JHA.
Please feel free to download any image from the below link and perform the conversion of image LWAPP to stand alone...
the methos to convert is...
Download TFTPd32 of google and install it on your PC... point of the image that you downloaded on the TFTP server.
Connect a cable ethernet between your notebook and AP... both should be on the same subnet... Connect a cable from the console and access the hyperterminal console with the command...
AP > en
AP #debug lwapp console cli or debugging console cli capwap
T AP #config
AP (confg) int FA 0
AP(confg-IF) ip addr (same subnet as the laptop)
End AP(confg-IF)
Force - reload DOWNLOAD - AP #archieve sw / overwrite tftp: / /.
This will solve the problem...
Concerning
Surendra
-
Is it possible to assign the DHCP pool to a specific SSID?
Hi experts,
I wanted to know if it is possible to assign a DHCP pool to a specific SSID on the Cisco Aironet 1142. If so, what commands do I need to implement?
Thanks in advance.
concerning
Fari
We can directly assign the DHCP for the SSID pool, we can map the SSID to a VLAN and this subnet VLANS can be configured for the DHCP pool...
If this client that connects to the SSID will hit him VLAN and then this VLAN the DHCP is reset...
On the access point, you can configure the DHCP pool or even on the switch or L3 device or server...
Regrads
Surendra
-
Difference between 1142 and 1042 AP
Is there a significant difference between these 2 Aironet AP series? Two of them can make the selection of band? I'm designing a business network wireless and I don't know about the choice of 1142 or 1042
There is not much difference... the 1040 is a mini series 1140 version... Apart from the softwate its supported on. It is 1040 needs latest software byt 1140 works on older
Here's the fact sheets as well...
In MIMO... 1141 is 2 X 3 but 1040 is 2 X 2
http://www.Cisco.com/en/us/prod/collateral/wireless/ps5678/ps10092/datasheet_c78-502793.html
http://www.Cisco.com/en/us/prod/collateral/wireless/ps5678/ps11203/data_sheet_c78-609338.html
Let me know if that answers your question and please do not forget to note the useful messages!
Concerning
Surendra
-
Not have access to the DGM or Web Console Aironet 1142n
Hello
I have Cisco Aironet 1142n.
I have currently no access to the config t to set up interfaces or the web console.
I found this article on the fact that my version of IOS is set incorrectly, but I can not implement telnet to improve the image that I have no access to the config to set a password on it. The AP is getting an IP address from the DHCP server and I can ping it but I can't access the web console either.
Any suggestions?
Thank you
You are more likely to have a lightweight access point when you wanted an IOS access point.
Download the IOS software to 1142, and then do the following on the console of the ap:
-debug console cli capwap
-archive download-sw/f/o tftp: / /.
Bingo, it restarts in IOS.
Nicolas
===
Remember responses of the rate that you find useful
-
I used the option "optimize the iphone storage" on my old phone to save space, but I hated waiting to load when I want to watch them. Now, I clicked on "Download and keep the originals", but I can't tell if my phone is re - download the original photos/videos to iCloud to my phone. What does automatically or are these pictures forever in the version "optimized" on my phone?
Subsequently, it must download the originals. Synchronization is VERY slow, so it may take some time depending on how many photos you have.
-
Disable the optimization of storage?
Hello
Just upgraded to macOS Sierra.
Is there a way to completely disable storage optimize? I don't need this?
In iCloud > iCloud Drive > Options, check 'Optimize Mac Storage' control everything?
I've checked it, is it enough?If you are going about this Mac > storage > Manage, there are a lot of options and I want that they OFF.
Thanks for any answers real *.
Steve
* true = not an answer like "why would you disable it?
dephilenaiguille wrote:
Hello
Just upgraded to macOS Sierra.
Is there a way to completely disable storage optimize? I don't need this?
In iCloud > iCloud Drive > Options, check 'Optimize Mac Storage' control everything?
I've checked it, is it enough?If you are going about this Mac > storage > Manage, there are a lot of options and I want that they OFF.
Thanks for any answers real *.
Steve
* true = not an answer like "why would you disable it?
Found a description of the function - which, when your local disk storage is low (but does not say how low) it will move the old (inactive) files to the cloud and remove them of your drive - they will be available in the cloud - new files stay on your system.
In order to optimize him unchecking storage should disable the function.
Best way to clean a disk is to back up permanent - even if this is a print - then remove it from your drive.
And it's something I would certainly turn off - as some 'old' documents are things that you need to keep but aren't necessarily watching.
-
Optimize my iPhone photo storage
My iPhone says that I have 20 GB of photos stored. I do not know if those that are stored on my iPhone or iCloud. How can I know who is who or both? I want to free GB of space on my iPhone. Thanks for the tips!
Hello
If you use iCloud photo library and also allowed the option optimises iPhone storage (settings > iCloud > Photos), then iCloud photo library automatically manages the size of your library on your iPhone.
If you are not already using iCloud photo library (including the optimization option), then you can consider doing.
The optimization option attempts to free storage on your iPhone by keeping versions space saving on your iPhone and the full-size originals in iCloud. Photos and videos are optimized on your iPhone automatically, if necessary.
Note that when you use iCloud photo library, removal of a photo or a video on any device that uses the service deletes also all other devices that use the service, including to iCloud.
The following resources may help explain how the photos and videos are managed by iCloud photo library:
Other resources:
-
Why is - app Photos asking storage optimize?
I get a message saying "your photos high resolution and videos stored in iCloud will not be indicated on the Mac" (a look of MacBook 13 inch mid-2013, El Capitan) and asking me to each 'ignore' this or 'optimize storage '. I don't understand why I get this message.
True, my photo library (full resolution stored) currently takes 44GB, but I have stored on a disk external drive 2 TB which has about 1 TB free, so there's plenty of room here. My main 250 GB drive has 17 GB of free, which is not a huge amount, but I don't know what is the role that plays since my lib Photos is stored offline.
Any thoughts?
Howard
You try to activate iCloud photo library for the first time on your mac?
If you want to use iCloud photo library, the gall of your external hard drive system can be incompatible. iCloud library cannot be enabled for the library system and the library must be on a disk with Mac OS extended (journaled) file system. If your external drive has a different file system, default Photos uses a system of Photo library on your system drive in the pictures folder and your system drive may not have enough free storage for your iCloud photo library.
If the file system of your external hard drive is Mac OS extended (journaled), make sure that this library has been enabled in your system photo library. "Use as Photo Viewer system" option should be greyed out ot, when you are in this library on the external hard drive.
-
Photos transferred via USB use optimize the functionality for iCloud photo library?
Hello
I recently transferred 1000 files to my mac via a flash drive.
I want to have optimized photos and not actually be fully downloaded on my mac and I'm currently using iCloud photo library with optimization turned on.
Does the work automatically? Or y at - it another way to make this work?
Thank you
Phil
When you import pictures to Photos on your Mac and they download to iCloud photo library they will be optimized on your Mac if space is needed - you cannot control what is optimized or when - it is dynamic and automatic
LN
-
When trying to optimize a Youtube video, nothing happens.
Whenever I try to optimize a Youtube video, nothing happens. I click the "Maximize" button but there is no answer.
I can watch Youtube videos in the "reduced" and "theatrical" view very well. I can watch videos on other sites on full screen as well. When I switch to another web browser, like the Chrome, I can watch Youtube videos in fine maximized mode.
Hi Chuckk.
1. go to Youtube.
2. once the site is loaded, click the padlock icon in the address bar.
3. set "Enter Fullscreen:"'Always ask' or 'Allow' permission. "(Remember to reactivate things like hardware acceleration if my solution worked).
Maybe you are looking for
-
Problem with some fonts of symbols after the installation of the Sierra
Hello I have recently upgraded the OS on my iMac late 2012 for Sierra, since doing so, I noticed a problem with several fonts. All symbolic symbols Apple to Wingdings fonts not correctly displayed in the font book. Apple symbols looks like a standard
-
importing photos in file/folder
Mac osX to yosemite; Tried to import photos from an SD card to the folder. they came last file imports, but couldn't move photos to a proper file/folder.
-
PC AIO 23 23 - b110eg: 23 b110eg Pavilion
My allinone PC monitor is black, I tried to reboot the PC in BIOS, but there is no reaction. I guess that the keyboard and the mouse is not recognized, since there is no witness lights when I restart the PC. Can you help me? Normally only the USB key
-
Best network and bluetooth driver
Hello. I have a hp probook 450 G0 - G1 without a network or Bluetooth drivers. Which would be the best driver to install on your site?
-
IFTHEN help financial information
Hello You will need to if so logical. I have the below: If the column A and column B is less than zero then (A - B) *-1 else (A - B). IFTHEN (([A] < 0 et [B] < 0), EVAL (([A]-[B]) *-1), EVAL ([A] - [B])) I need: If the column A and column B are below