output ascii 'code' for serial port

Similar Questions

• Always replace the output file for serial port.

  Hello, I use Workstation 7 on Linux and use the option "Output to a file" serial port for the logging of messages to the client for debugging.

  It works perfectly, however, if the file exists already workstation asking what to do (crush, add, etc.). It works, but I would like to have the option to auto restart, restore, instant, etc. and this message gets in the way.

  Is he a .vmx parameter I can apply to my computer always replace the output file without asking?

  Yep - found

  you need these two lines:

  msg.autoAnswer = 'TRUE '.

  Msg. Serial.file.Open = 'Add '.

  _________________________

  VMX-settings- WS FAQ -[MOAcd | http://sanbarrow.com/moa241.html]- VMDK-manual

  You find me also in the PhD Virtual Backup support team

• HP ZBook 15 G2: I can't find driver for Serial Port PCI

  After re-installation, my HP ZBook 15 G2 is missing the driver for "PCI Serial Port (COM5)".

  This unit has the following ID: VEN_8086 DEV_8C3D

  I installed all the drivers for chipset for the HP ZBook 15 G2.

  Where can I find the driver for this device?

  Hello:

  You need this driver.  If the driver will automatically install the driver for serial port, and then manually install the device by navigating to the folder of the driver that was created when you ran the file.

  This file will be located in C:\SWSetup\sp68428.  Make sure that the include subfolders is selected and the driver should install.  Then restart.

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=6978815&swItemId=ob_137806_1&swEnvOid=4059

  The hardware ID you posted is supported by this driver if you look in the mesrl configuration file.

  [Intel.NTamd64]
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_1E3D & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_1CBD & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_1C3D & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_1DBD & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_1D3D & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_8C3D & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_9C3D & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_9CBD & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_8D3D & CC_0700"

• HP dc 7800 how can I install the driver for serial port pci Windows 8.1

  HP dc 7800 how can I install the driver for serial port pci Windows 8.1 Please help

  Hello:

  Download and install the W7 AMT driver.

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=3459243&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dvc_78665_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• Win 7 / T500: no driver for Serial Port PCI

  I have what I think it's all Lenovo installed software after an upgrade to Windows 7. This includes the touchpad and Intel AMT drivers. However, I show still no drivers for "PCI Serial Port" in my device manager.

  No idea how to solve this problem of exceptional pilot?

  Thank you!

  _Bruce_

  The manufacturer is Intel and here is the link for the driver you need:

  http://www-307.IBM.com/PC/support/site.WSS/document.do?sitestyle=Lenovo&lndocid=MIGR-73567

  I think that you just install this driver in case you have Intel AMT active. If Intel AMT is disabled I do not think that this device will be shown in Windows.

• Windows 7 drivers for serial port PCI compatible for ThinkCentre M57p (6088)

  The weekend I upgraded my Lenovo M57p (model 6088) to Windows 7 and encountered the problem in which the drivers for the following were not installed and could not be located...

  PCI Simple Communications controller

  PCI serial port

  The problem here is that the AMT/drivers available for this problem are not compatible for PCs running Windows Vista, XP or 2000 but do not go as far to cover the problem created in Windows 7...

  http://www-307.IBM.com/PC/support/site.WSS/document.do?sitestyle=Lenovo&lndocid=MIGR-73601

  Can anyone suggest what I can do to fix this?

  I noticed that Lenovo have beta versions available these drivers for the Thinkpads but for some reason, none of the drivers are available for the ThinkCentres.

  I don't understand what I am sure to be a major problem when others will upgrade to Windows 7...

  Does anyone know when Lenovo plan to get Windows 7 compatible AMT/drivers for the ThinkCentres?

  Really need help because my PCI and PCIe ports do not work, so my sound card...

  It seems that Intel AMT:

  http://support.Lenovo.com/en_US/research/hints-or-tips/detail.page?&LegacyDocID=MIGR-68783#AMT

• Measurement & Automation explore (MAX) cannot find any serial ports

  Hello

  I tried half of the internet, but I can't find a solution for my problem. Maybe someone of you have an idea :-)

  My System Information:

  OS: Windows 7 (64-bit)

  LabView: LabView Professional Development System 2015 (32 bit)

  MAX: Version 15.0.0f0

  NI-VISA: 15.0

  NOR-Serial 14.0

  I've attached a screenshot of MAX at the end of my post.

  All the drivers for serial ports are properly installed (see another screenshot). But Max, I can't find these ports. There is only the error code "0xBFFF0011 (VI_ERROR_RSRC_NFOUND). If I want to add the COM Port via 'Devices and Interfaces'--> 'New'--> ' Port (serial or parallel) ", I can only choose between COM1-COM4 and LPT1-LPT4. But I need COM9!

  Anyone have any idea what I did wrong?

  Thank you

  deZeus

  I looks like something is wrong with your installation OR VISA (as MAX does not find ALL ports).  Make sure that NEITHER VISA is activated (sometimes of other kinds of visa in the way), or try reinstalling NI VISA.  Serial number NOR is not necessary since you are not serial ports using OR.

• HP DC7700: Serial Port PCI and simple Communication controllers pilots missing in HP DC7700 windows 7 (32 bit)

  PCI\VEN_8086 & DEV_2997 & SUBSYS_2801103C & REV_02
  PCI\VEN_8086 & DEV_2997 & SUBSYS_2801103C
  PCI\VEN_8086 & DEV_2997 & CC_070002
  PCI\VEN_8086 & DEV_2997 & CC_0700

  and

  PCI\VEN_8086 & DEV_2994 & SUBSYS_2801103C & REV_02
  PCI\VEN_8086 & DEV_2994 & SUBSYS_2801103C
  PCI\VEN_8086 & DEV_2994 & CC_078000
  PCI\VEN_8086 & DEV_2994 & CC_0780

  Experts in the House should please come to my rescue.

  I just upgraded my Hp DC7700. I was able to get all the drivers except for SERIAL PORT PCI and PCI SIMPLE COMMUNICATIONS CONTROLLER missing. above are the two missing pilots hardware ID

  Hello:

  There is no W7 drivers for these devices.  You must use the Vista drivers and if auto installation does not work, you will need to install the drivers manually by navigating to the folder of the driver that was created when you ran the file from the device in the Device Manager (browse my computer for driver software).

  This package contains the driver Intel Host Embedded Controller Interface (HECI) for access to Active Management Technology (AMT) initiative of the Intel Digital Office for rated desktop models and operating systems.

  FTP://ftp.HP.com/pub/SoftPaq/sp34501-35000/sp34743.exe

  This package contains the Intel (LMS) Local Management Service and Serial - over - LAN (SOL) support for the technology of Directors Active (AMT) under the Initiative of digital office Intel for the supported desktop models and
  operating systems.

  FTP://ftp.HP.com/pub/SoftPaq/sp34501-35000/sp34744.exe

• Communication Serial Port without a VISA

  Is it possible to connect to the serial port without a VISA?

  The thing is that the VISA is required to be installed on the deployed machine. It is not for my client.

  Thanks for any help.

  You can find driver series placed in Non-VISA:

  http://www.MHST.de/downloads.htm

  Benefits:

  • you need not install DURATION VISA on a deployed machine. Place a dll (dll is included) in the system folder - that's enough.
  • There are several additional features that has no VISA
  • works reliably

  Disadvantages:

  • Works for serial port only
  • uses the WinAPI functions

• Reading codes ascii serial port and their trace

  Hello

  I am trying to build a VI that reads data (ascii values) of the serial port.

  I am trying to build a Phonocardiogram wireless. I have a microphone that acquires the heart sounds. These signals is amplified and sent to an A/D converter to digitize it. the digital signal are sent to a base unit. UNTV signals received by the base unit must be sent to a computer (via a serial port to display).

  I would like to build a VI to draw ascii data received through the serial port.

  I would like to draw these values so that the plot resembles an analog signal (the one I had before an A/D converter).

  Can someone give me help?

  Thanks in advance...

  HII

• Waiting for data on serial port

  Hello everyone.

  I'm trying to figure out how I can solve a problem on LabView. I programmed an Arduino board to read and send a data table of the accelerometer on the serial port. I want to LabView to receive the data and graphs it. My problem is that Arduino send data on an ongoing basis and sometimes LabView can not cope with traffic and read some values "0".

  Is it possible to wait for the data and solve this problem?

  I joined my current vi.

  Thank you much in advance.

  AndreasSchnaas wrote:

  Yes, the characters are 0-9 and - no. ' + 'or'. '. And bytes that vary.

  Once again, thank you very much.

  Given that you send ASCII characters, change your Arduino code to send a character to end of line (10 byte value) at the end of each transmission.  Your code is already configured to use it.  Then you need not use the bytes to the Port at all.  Suffice to say the VISA of reading to read a large number of bytes.  Playback stops when it finds the stop character (value 10).  Your code will get a lot easier from there.

• serial port: input/output signal combined suburbs

  I am currently using LabView to replace another user for a scientific instrument interface.

  LabView is connected to this unit via a serial port.  The instrument spread 25 bytes of binary data from the computer every second.  I can read the binary string (Read VISA) and maintain will cause disc using a while loop.  In addition, there are some instructions I can send to the device that will do various functions (start logging, turn the LED on / off, etc.).  I can send these instructions to the instrument using the previous interface and in a stand-alone vi using VISA Write successfully, but when I place the function Write VISA in the largest interface vi, signals go haywire.  Specifically, there are two separate lights I can alternate with two different commands, but when in the biggest interface vi, the two commands Toggle the LED even.  In addition, it seems that the singal that immediately send to the instrument (a single ASCII character) bounces to the computer in the 25 bytes of binary data streaming.  In other words, after I pressed the LED 'on' the key, a column of my streaming data changes when it's not supposed to (ex: after binary to ASCII conversion, changing a single digit in a 20 digit value).

  At first, I thought that the problem was the sequence of read/write VISA.  I read all the data in the current configuration, and then leave for orders writing.  The two VISA functions are in the same loop to continuously monitor the data.  Is it possible the signal output of writing not letting the while loop and being read as input?  What would the instrument two different commands as the same as read?  My goal is to run an interface that displays data in ASCII and allows some options different rocking while that the interface works - there is an elegant/effective way more as a while loop?

  ~ Going bananas

  
  

• Part number for the serial port in option HP Z420

  I am looking for the serial port in option for the HP Workstation Z420, but in a datasheet, it is only mentioned as an optional serial port kit.

  What is the number on the right side of the product? The same for the workstation Z400 was PA716A, but it was not compatible with the new workstation model...

  I used the same part number, I used to model Z400 and it seems to work well.
  HP code is PA716A.

• Signal output data expressed on a serial port

  Hello everyone,

  I received a task which requires me to collect several channels in express signal analog voltages before displaying these data to the serial port of the computer. My programming experience is very limited as Im working on the back of the high school before going to College, and even though I have the foundations of basic labview stowed, Im struggling to understand how to approach this problem.

  I started looking at the base read the series and write vi provided in the examples and I know how to get labview vi to intergrate with signal on purpose, but because of my lack of knowledge related to the use of channels of communications, binary, hexadecimal and asqui I don't really know where to go from here. The writing and reading of strings for example, I don't understand.

  I would like the data are ideally output on the serial port in real time and data are collected continuously at 6 kHz.

  I realize that there probably is no simple answer to this question, given my lack of knowledge, but any help would be greatly appreciated!

  Thank you!

  Harry

  Hi hcook,

  As smercurio_fc said, the strings that you send are totally dependent on what you're talking about. I haven't used a 'box of dspace' before, but a normal serial device will wait to receive specific orders.  Once it receives an order of some, she will perform a certain task.  You are right in saying that you need to establish what string commands to send to the box of dspace.

  You can find these useful:
  General concepts of Serial Communication
  Overview of Serial Communication

  I hope this helps.

• Using the Serial Port for data acquisition Non-Serial

  I searched the forums and can't find anything on this topic.

  I saw that it was possible to use the parallel port for e/s digital single and I was hoping that the serial port can be configured the same. It seems all VI VISA only to use the serial port to receive ASCII characters at a given flow rate, but is it possible to simply query the status of the line series at my own speed to see if it is high or low, kind of like a single pin DAQ?

  It seems that it would be possible until the serial data are read and controlled by labview, not Windows. Let me know if you have ideas of how to approach this problem, or any comment as to why it is not possible.

  Thank you all!

  Select the property > settings series > Modem of the line parameters. For example, the State of the CTS is an entry to the pc.

  With the help of these lines is a very poor substitute for a scope or map DAQ. The only things you can return is Asserted, Unknown or Unasserted. The range of acceptable signals is important enough. Anything between + 3 and -3 is an unknown state. Your other signals is + / 3 to 15 volts. What type of signals do you really want to capture?

  Edit: there is no such thing as a visa so I have no idea of what you actually use.