Output switching PWM of routing

Similar Questions

• Can I quote the 'switch' inside my router?

  I hope there is a way to name the 'switch' in my router so that it shows up as anything other than "unknown" in my network card in Windows. Is this possible? Or maybe just a way to make it appear differently in Windows 7, as to change the icon to something other than a question mark? I ask not how the router itself, maned I wondering how to add a name to the switches inside in the Windows network mapping. It would be nice if it was still just "port 2" "port 3" etc.

  You can not

• Why do I have 2 routers on nerwork card with a switch, when a router is mine?

  network map says that there is another router on my computer with a card switch.nework reading order my computer then a dlink router that is not mine then a switch then my router.the cisco router which is not mine said d-link international pte limited with a mac IP... 1 c: AF:F7:CC:AC:19.how I get it my computer?

  I formatted problem solved... Thank you

• HP pavilion dm4: removing the battery / output switch problem

  MY hp dm4 Clubhouse has a switch relese battery does not move and so I can't remove the battery.

  What can I do to take out the battery?

  I was able to remove my battery, even if the trigger will not move

  I have read the documents under the next heading

  "Laptop battery seems to be stuck.

  He pointed out that my problem was very common

  BATTERY REMOVAL PROCEDURE

  As suggested-

  I inserted a piece of thin stiff plastic

  (for example on the size of a credit card but a little thinner)

  in the crack between the battery and the output switch

  I pushed the upper part of the plastic down

  and then I pushed up in the direction of the battery

  up until the crack of batttery widened to the point where I could use

  my nails in the battery of crack to pull the battery.

  I don't have to much force to make

  The angled battery to easily

  BATTERY INSERTION PROCEDURE

  As suggested-

  To avoid the problem of gel battery switch

  Move the latch of the battery in the middle of its sliding range

  When reinserting the battery first tilting the battery

  so that the side of the battery to the side of the computer case

  is first inserted into the battery compartment

  Then push down the other side of the battery in its compartment

  in the end, release the battery button while he spingngs to its normal resting position.

  I hope that this explanation is useful

• PowerConnect 6248 switch for Cisco router

  Hello

  I'm new to this forum and I have a problem at the moment between a Cisco router and a dell pc6248. The problem is that I lost conectivity in VLAN 1 when I connect the router to a trunk port in the switch, however I conectivity VLAN 2 through this link to trunk. The configuration of the switch:

  interface ethernet 1/g48

  switchport mode trunk

  switchport trunk allowed vlan add 1-2

  output

  interface ethernet 1/g43

  switchport mode access

  switchport access vlan 2

  output

  On router

  fast interface 0/1

  no ip address

  no downtime

  fast interface 0/1.1

  encapsulation dot1q 1 native

  IP 192.200.3.1 255.255.255.0

  fast interface 0/1.2

  encapsulation dot1q 2

  IP 192.168.51.33 255.255.255.248

  output

  With the above configuration, I lost conectivity with the host in the vlan 1 - 192.200.3.x/24, but I win conectivity VLAN 2, when I connect the router to the 48 trunk port in the switch. This means that the trunk link for VLAN 2 work but not for VLAN 1.

  I read on the port of general mode, where I can configure the pvid of the port as 1 (vlan1) and it would be the unttag VLAN (even natively in Cisco), and I can configure the VLAN 2 like the tag, all this in the same port. What do you think about this? Someone have set up something like that?

  Best regards

  Erasmo

  PD: I write from Chile, I apologize for my English.

  I agree with you, I would try the general mode on the PowerConnect switch.

  mode console # switchport general

  Console # switchport General allowed vlan add 2 tag

  Console # switchport pvid General 1

  Keep us updated.

• Sending a pulse to pin using an output switch

  Hello

  This is my first program in labview.

  I want to use a while loop continually between data for the acquisition of data that displays on an oscilloscope. The output signal must be controlled by a switch (0 when the switch is open) and 1 when the button is pressed.

  I put a toggle switch in the while loop and connected the output to data acquisition Manager, but he demonstrated a connection error.

  Source type is Boolean.

  Type of sink is 64-bit real.

  So, how can I convert data from the switch so that it gets feeding the DAQ output?

  Thank you.

  Soham_S wrote:

  When the switch is off, he sends a zero, when turned on, it sends a 1.

  You will need to keep DAQmx inside the while loop probably you can use the structure of the event to do this. Also even if you set up the digital output you must select channel instead of multiples (unless you really have multiple channels) then you can connect the switch directly to it.

• The access key for the peripheral output switch?

  With the help of Adobe Audition CC on an i - Mac 21.

  So I check my mix via my usual interface.  Now, I want to quickly check on another pair of speakers, for example a small pair of USB speakers.

  My question is this:

  Is there anyway to implement a simple keyboard shortcut to enable me to move quickly from my output from one to the other?

  Please guide me through it, if possible.  Be very grateful - thank you.

  You can get some of the way in which it by setting up a keyboard shortcut to directly access the Preferences page / Audio Hardware. It is under the Edit/keyboard shortcuts/preferences.

• relay output switches together

  Hello

  I'm currently testing a simplified system of PID before I run the entire process. The system consists of a heating controlled by a relay and an RTD cushion that feeds back the temperature. Everything works very well. I have a simple Subvi which, according to the block of PID, exit lights relay for awhile about every 5 seconds. I set the system with only one relay and rtd and it worked fine. Now, I tried to put the two relays in the system and they seem to only run alternately. For example, if so they turn on once every 5 seconds, now, one turns, then seconds an active, doubling the time between them turning on. I know that they can turn on at the same time as I have tested that and even changed back to make sure that is not the issue. It seems that it is something in the code, I put together to pass. If anyone has any ideas, that would be great.

  Attached are the simplified PID loop and the Subvi turn on the relay.

  Start by making the reentrant Subvi and see if that helps.  (File > VI properties > run.)

• configuration of VLAN and routing problem 6224 switch

  I, m having a problem accessing internet to vlan 10. I can ping everything of all the VLANS. My internet router/firewall is on ethernet 1/g11 and has an ip address of 192.168.5.254. I have no problem accessing internet to vlan 20. I add a static route to my router/firewall. What Miss me? This is my first configure a layer 3 switch.

  Configure
  database of VLAN
  VLAN 10.20
  output
  battery
  1 1 member
  output
  IP 10.10.10.1 255.255.255.0
  default IP gateway - 10.10.10.254
  IP routing
  IP route 0.0.0.0 0.0.0.0 192.168.5.254
  interface vlan 10
  Routing
  IP 192.168.100.1 address 255.255.255.0
  output
  interface vlan 20
  Routing

  192.168.5.1 IP address 255.255.255.0
  output

  !
  interface ethernet 1/g1
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10
  output
  !
  interface ethernet 1/g2
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10
  output
  !
  interface ethernet 1/g11
  switchport mode general
  switchport General pvid 20

  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  !
  interface ethernet 1/g12
  switchport mode general
  switchport General pvid 20
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  !
  interface ethernet 1/g13
  switchport mode general
  switchport General pvid 20
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  output

  Route ip console #show

  The traffic code: R - RIP derived, O - OSPF derived, C - connected, S - static
  B - BGP derived, IA - OSPF Inter zone
  E1 - OSPF external Type 1, E2 - OSPF external Type 2
  N1 - OSPF NSSA external Type 1, N2 - OSPF NSSA external Type 2

  S 0.0.0.0/0 [1/0] via 192.168.5.254, vlan 20
  C 192.168.5.0/24 [0/0], directly connected, vlan 20
  192.168.100.0/24 C [0/0], directly connected, vlan 10

  Console #.

  
  

• How is the best way to connect the configuration of my router and switch?

  I have a cable modem. connect to a switch, I have 2 computers connected to the switch. I also just connected my router wireless switch. That's the best configuration or I lose my firewall of the router in passing is not by ports directly above?

  Most of the cable modems will give an IP address, so connect a switch to the modem and then connection of two computers and a router to the switch will usually result in one of these three devices, get an IP address (and internet connection), while the other two will not be.  (Notice that I guess a true "Modem" and not a "Modem/Router" device).  The correct configuration would be to connect your router to the modem (router gets the unique IP address).  The router can then process from the addresses IP what either side LAN of the router, then plug the devices you need (including switch) to the router's LAN ports.  This also ensures that all devices will be on the same subnet that your connection scheme to separate devices on the router wireless from the other two devices on the switch (here, assuming that you have a router/Modem device).

  HTH,

  JW

• Switching mode of EPC 3925 / router E3000 speed 20% loss

  my setup is EPC 3925 Switch mode - E3000 router mode

  my ISP speed is 200 Mbps I only have 160 MB/s maximum and is not stable

  When I use the EPC 3925 I get 200 Mbps

  can someone explain why this happens

  takwansani wrote:

  Thanks Meegosh and nerD_sayer for answers

  one last question what happens if ask my ISP to swap the 3925 to a modem router as the 3208

  I gain speed?

  Yes. It is better to have just a modem ordinary to avoid double NAT issues as well as port easier opening if it is necessary to do so.

• Cisco SG 300-20 switch connects to the router

  Hello

  I try to install my new switch Cisco SG300-20 in my local network, but I'm not succeed.

  The SG 300-20 fails to connect to my router.

  When the router is directly connected to the SG 300-20 I fails to obtain the DHCP configuration. Any port I try fails.

  When I add a former switch between the router and the SG 300-20, SG 300 - 20 manages to get the DHCP configuration.

  When I use a static IP on the SG 300-20 and the router is directly connected, it is not an operational bridge in the IPv4 configuration.

  Where I'm looking for a solution?

  The SG 300-20 is maybe defective and I would stay there?

  A. van Egmond

  A few things you can check are:

  See if the system is blinking. If it is the default ip address. If it is solid the IP address has changed due to a static assignment or DHCP.

  If no link light is on or the system flashes, the reason why could not tear out DHCP is due to a shift of port negotiation. Try setting the port on the router or the full 100 MB switch or what ever you like just to see if that helps.

  Make sure that you are also on the latest firmware.

  Try factory default of the switch with the button of reset for 45 seconds.

  Cisco Small Business Support Center

  Randy Manthey

  CCNA, CCNA - security

• The managed behind router switch remote access?

  What is the best way to access remotely to a switch behind a router?  I will use a switch SF300, and there is no server.

  For points of access (PA) behind a router, I give each a diffferent LAN address and port number.  In router I have forward TCP traffic with the single port/LAN IP.  Then using the port numbers with the address of the static router, the browser can remote access to the router or the attached AP.  But where do I put the managed switch LAN port number?  Assume default is port 80 and I would change to 8001 to switch #1; 8002 to switch #2; etc.  Could not find this info in the manual of configurtion.

  Hello

  At this point, I would recommend a call to the Cisco Small Business Centre at 1-866-606-1866 support so that action can be taken and your configuration can be reviewed.

  I have reproduced the concern here and I am able to remotely manage my switch SF300 with an RV082 as the router.

  My rule in the RV082 are as follows:

  Creating a custom topic UPnP service.  Create SF300 application name (it is a basic text field and can be any name), 8001 an external port and internal port 80.  I send to the address IP internal SF300 switch and click the check box.  From there on, I select Add to the list.  Once it appears in my list, I then click Save settings at the bottom of the page.

  Thank you!

  Dave

• EIGRP running between the router and ASA by switch

  Hello

  Is that possible I can running an EIGRP between router and ASA by switch?

  Router and ASA connected to the switch with static route.

  Hi Tommy Chin.

  It is possible, we must advertise to the route between the router and ASA.

  Please provide your connectivity diagram to better explain.

  For example...

  interface GigabitEthernet0/0

  Description links to WAN router

  nameif OUTSIDE

  security-level 50

  IP 10.1.1.1 255.255.255.192 ensures 10.1.1.2

  Summary-address eigrp 100 10.1.0.0 255.255.0.0 1

  !

  Confiuration Protocol EIGRP

  standard access list eigrpACL_FR allow a

  !

  Router eigrp 100

  eigrpACL_FR distribute-list in the interface outside

  neighbor 10.1.1.3 OUTSIDE interface

  neighbor 10.1.1.2 OUTSIDE interface

  Network 10.1.1.0 255.255.255.192

  redistribute connected

  redistribute static

  !

  Kind regards

  Srinivas.

  Note: if it solves your problem it mark it as resolved.

• How is it that a computer which works very well with a direct Ethernet connection won't work with a switch, however any other computer using the same port, cable, ect, and so on, can?

  Switch issues. Help, please.

  How is it that a computer which works very well with a direct Ethernet connection won't work with a switch, however any other computer using the same port, cable, ect, and so on, can? We already checked the firewall as a question, that it was not, and now, we are puzzled.

  Well, I know that the issue is long-term... believe me, it's a long, but as they say, the devil is in the details. Anywho, the question is, my grandfather has a HP laptop, which for two years has been able to run through a Linksys switch to his router and connect its printers to his laptop. About two months ago it suddenly doesn't work like that. Now, it works fine if it plugs directly into the router/Ethernet. My uncle suggested that the switch was bad, but after testing the same port, cable and all, the switch worked well for him. ' GRAMPS really needs this answered, but someone else, it is called can not understand and now I, in turn, ask you all for what you can offer. Here are the ideas that we have already discredited.

  -Switch bad: as above, is that this particular laptop, even under identical conditions, the works of my uncle very well.
  -Bad NIC: debunked through the fact we connected to the computer directly to the router and it worked fine.
  -Bad configuration of the firewall: we have disabled the firewall (please do not notice, he wasn't the smartest idea, we already know) and even if she recorded the switch exists, the internet is always triggered when you are connected with the switch.

  Thanks in advance for any assistance that you can provide and Merry Christmas to you all.

  It would be useful to consult the results of the ipconfig/all command both when it is connected to the switch and when it is connected directly to the router.  In addition, what is the model of the switch?

  To save the manual copy and the new hits of the ipconfig/all command output-

  First connect through switch.
  Open a command prompt window (start > run > cmd > OK)
  Type the following lines in the black command prompt window and press ENTER after each line

  echo "Connected via the button" > "% UserProfile%\Desktop\ipinfo.txt".
  ipconfig/all > "% UserProfile%\Desktop\ipinfo.txt".

  Now connect directly to the router, type the following lines in the command prompt window and press ENTER after each line

  echo "Connected to the router" > "% UserProfile%\Desktop\ipinfo.txt".
  ipconfig/all > "% UserProfile%\Desktop\ipinfo.txt".
  Notepad '% UserProfile%\Desktop\ipinfo.txt '.
  output

  Copy the contents of the Notepad window in your response (if you use the laptop when it is connected directly to the router) or close the Notepad window, and then copy ipinfo.txt of the laptop to the Gramps in a USB FlashDrive you can connect to any computer allows you to answer.

  You can delete ipinfo.txt on the desktop when you are finished.