The managed behind router switch remote access?

Similar Questions

• Routing and remote access - on three subnetworked, two subnet unable to reach to the internet!

  Hello

  Good evening everyone.

  I had a problem in Routing and remote access on windows 2003 server.  This server is already configured as a file server, domain server, and application server. Also configured as a router (thanks to access routing & remote) to connect the three different networks with each other. If this server has three NICs installed and each separate NIC network cards represent.

  three different networks are - 192.42.160.0/24, 192.42.161.0/24, 192.42.162.0/24

  Three cards of the NETWORK adapter installed on the server as with the IP - next

  NIC - 1 = 192.42.160.220, Sub - 255.255.255.0, gateway - No.

  NIC - 2 = 192.42.161.220, Sub - 255.255.255.0, gateway - 192.161.220.112 (this ip address for internet access then 4 g router IP)

  -3 = 192.42.162.220, NETWORK cards, Sub - 255.255.255.0, gateway - No.

  Now the question is I can get Internet & (also scathing in router ip 192.42.161.112) one network i.e. - 192.42.161.0/24, BUT when I try to access the internet from another two network (192.42.160.0/24 & 192.42.162.0/24) I can not access and in addition can not ping to internet router ip - 192.42.161.112...

  So, how do I access the internet to another two network also?

  I was already the configuration of static routing for all three network but I wasn't always successful. I don't really know what exactly static routing this should be done in access routing & remote area so that all three network can reach to the internet?

  Here is the result of the current track...

  D:\Documents and Settings\Administrateur > route print

  IPv4 routing table
  ===========================================================================
  List of the interface
  0x1 ........................... MS TCP Loopback interface
  0x2... 00 30 05 8f ad 5 c... Broadcom NetXtreme Gigabit Ethernet - Mi Teefer2
  niport
  0 x 3... 0E 00 c4 f8 a7 0c... Network Intel(r) PRO/1000 GT Desktop Adapter - Teefer2 M
  iniport
  0 x 4... 0E 00 0c a7 c5 85... Intel (r) PRO/1000 GT Desktop Adapter #2 - Teefer
  2 miniport
  ===========================================================================
  ===========================================================================
  Active routes:
  Network Destination gateway metric Interface subnet mask
  0.0.0.0 0.0.0.0 192.42.161.112 192.42.161.220 1
  127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
  192.42.160.0 255.255.255.0 192.42.160.220 192.42.160.220 20
  192.42.160.220 255.255.255.255 127.0.0.1 127.0.0.1 20
  192.42.160.255 255.255.255.255 192.42.160.220 192.42.160.220 20
  192.42.161.0 255.255.255.0 192.42.161.220 192.42.161.220 20
  192.42.161.220 255.255.255.255 127.0.0.1 127.0.0.1 20
  192.42.161.255 255.255.255.255 192.42.161.220 192.42.161.220 20
  192.42.162.0 255.255.255.0 192.42.162.220 192.42.162.220 20
  192.42.162.220 255.255.255.255 127.0.0.1 127.0.0.1 20
  192.42.162.255 255.255.255.255 192.42.162.220 192.42.162.220 20
  224.0.0.0 240.0.0.0 192.42.160.220 192.42.160.220 20
  224.0.0.0 240.0.0.0 192.42.161.220 192.42.161.220 20
  224.0.0.0 240.0.0.0 192.42.162.220 192.42.162.220 20
  255.255.255.255 255.255.255.255 192.42.160.220 192.42.160.220 1
  255.255.255.255 255.255.255.255 192.42.161.220 192.42.161.220 1
  255.255.255.255 255.255.255.255 192.42.162.220 192.42.162.220 1
  Default gateway: 192.42.161.112
  ===========================================================================
  Persistent routes:
  None

  Sorry if I'm not able to explain properly. Please let me know if you have to explain more about it...

  Thank you all.

  Mahesh

  Hello Manu,

  Please post this question in the forums TechNet for Windows Server 2003. They will be able to guide you further.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home

• The Routing and remote access could not start, error 214500037 (0x80004005)

  My windows server 2003 r2, failed to start the Routing and remote access services. And in the event an observer log, it has error code
  Event ID: 7024, with service specific error 2147500037 (0x80004005)
  I tried to reset tcp/ip and replace ias.mdb and dnary.mdb by a new, but it did not work.

  Thank you

  Hi budhihartono,

  Since you are facing problems with windows server 2003 r2, it would be better suited in the Technet Windows forum. Please post your question in the following TechNet Windows server forum to improve assistance:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• Routing and remote access to the Server 2003

  I configured the remote access and routing service in my Server 2003 duly NAT enabled. All my clients are not in the field. All use internet and intranet connection using my proxy authentication provided by the administrator of the proxy server. I would like to restrict the clients except intranet connection. How to limit the customer?

  Post in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• Server ezvpn 887 router for remote access

  Hello.

  I'm having a problem with the implementation of remote access using easyvpn server on a router 887.  I followed the tutorials and also used Assistant cisco configuration professional easyvpn server to the configuration but still having a problem.

  I see, but Phase 1 finished, Phase 2 will fail with the following error...

  09:43:26.515 Oct 10: ISAKMP: (2003): check IPSec proposal 8

  09:43:26.515 Oct 10: ISAKMP: turn 1, ESP_AES

  09:43:26.515 Oct 10: ISAKMP: attributes of transformation:

  09:43:26.515 Oct 10: ISAKMP: authenticator is HMAC-SHA

  09:43:26.515 Oct 10: ISAKMP: key length is 128

  09:43:26.515 Oct 10: ISAKMP: program is 1 (Tunnel)

  09:43:26.515 Oct 10: ISAKMP: type of life in seconds

  09:43:26.515 Oct 10: ISAKMP: service life of SA (IPV) 0x0 0 x 20 0xC4 0x9B

  09:43:26.515 Oct 10: ISAKMP: (2003): atts are acceptable.

  09:43:26.515 Oct 10: IPSEC (validate_proposal_request): part #1 the proposal

  09:43:26.515 Oct 10: IPSEC (validate_proposal_request): part #1 of the proposal

  (Eng. msg key.) Local INCOMING = 88.xx.xxx.174:0, distance = 80.177.185.185:0,.

  local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),

  remote_proxy = 192.168.21.12/255.255.255.255/0/0 (type = 1),

  Protocol = ESP, transform = NONE (Tunnel),

  lifedur = 0 and 0kb in

  SPI = 0 x 0 (0), id_conn = 0, keysize = 128, flags = 0 x 0

  09:43:26.515 Oct 10: map_db_find_best found no corresponding card

  09:43:26.515 Oct 10: IPSEC (ipsec_process_proposal): proxy unsupported identities

  09:43:26.515 Oct 10: ISAKMP: (2003): IPSec policy invalidated proposal with error 32

  'Proxy unsupported identities' research indicates a NAT problem maybe, but I don't see where this would be.  In my view, the problem is elsewhere.

  I use the VPN Client 5.0.07.0440 and using transparent tunneling IPSec (on TCP/10000) that the client is located behind a firewall/NAT device.

  Does anyone know what may be the issue?  Attached full config.

  Hello Mick

  Before that, one more try. .

  Remote control the pfs as follows

  Profile of crypto ipsec RemoteAccess

  no set pfs group2

  Remove and add the virtual model crypto back

  type of interface virtual-Template1 tunnel

  No ipsec protection RemoteAccess tunnel profile

  Profile of tunnel RemoteAccess ipsec protection

  I hope this will solve your problem

  Henin,

• How to use Layer 2 Ports on the Cisco 1841 router switch

  Hello

  I use the Cisco 1841 router with a single port layer 3 Fe0 and 8 Ports switched.

  I gave the IP on the Fe0 port which is connected to another router.

  Now I don't know how to use Layer 2 of the router switch ports.

  I tried to make one of the port as a Port of access by switchport mode access and connected my laptop and the same subnet given IP, but I can't ping my Fe0 IP port and vice versa, as I am also unable to ping my laptop router.

  Can someone explain to me how to use these ports on layer 2?

  Hi Muhammadatifmasood, take a look at the link below, I'm sure that you will find it useful.

  https://supportforums.Cisco.com/discussion/10919631/how-enable-routing-b...

  BenSamayoa

• Is the phone call received requesting remote access to solve the problem under Windows a scam?

  I received a phone call requesting remote access to my computer to solve a problem with Microsoft Windows more precisely line X 5.  The call came from Salt Lake City Utah, phone number 801-839-2099.

  I got this phone call once a week.

  Is it a scam?

  It's a scam.  Next time you receive such a call, tell the caller you declare calls to the police as harassment for fraudulent purposes... maybe they'll leave the call.

  http://www.Microsoft.com/security/online-privacy/msName.aspx

  http://www.Microsoft.com/security/online-privacy/phishing-scams.aspx

  http://www.Microsoft.com/security/online-privacy/avoid-phone-scams.aspx

  http://www.mypchealth.co.UK/GuideScam.php

  http://blogs.msdn.com/b/securitytipstalk/archive/2010/03/09/Don-t-fall-for-phony-phone-tech-support.aspx

  http://ask-Leo.com/i_got_a_call_from_microsoft_and_allowed_them_access_to_my_computer_what_do_i_do_now.html

• How can I assign the static fixed IP for remote access VPN users

  Hi team,

  I have a requirement to assign a fixed static IP users VPN remote access in ASA, please help how I can achice this

  Thanks in advance
  Mikael

  username user1 attributes

  VPN-framed-ip-address 10.200.115.78 255.255.0.0

• Routing and Remote Access Server & VPN

  We have Server Windows 2008 R2, which is our domain, but also DHCP server controller. On this server we have Setup RRA for VPN and it works fine. We had to stop our DC due to a failure and after I got the domain controller to the top and it is a problem for users that connect to the VPN.

  When users try to connect to the VPN, it connects successfully. But they did not access network as usual. I looked in the VPN properties, and it receives an IP address of 169.254.xxx.xx which is not the correct network IP address. So while the user who is remote think they are connected, they are currently not connected.

  Does anyone have advice what is the cause of this and how to troubleshoot or resolve?

  Hello

  Given that you are working on Windows 2008 R2 please post your question here:

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home

• The use of Teamviewer for remote access to another PC from a PC

  Hello

  I have TWO PC, but unfortunately two PC has the same IP I checked ipconfig.

  I called ISP regarding on the same IP between two PCs.

  Is it possible that a PC can access second tool PC remotely using the Teamviewer software, even if TWO PC IP addresses are the same now?

  Your comments will be appreciated.

  Thank you

  Hi Altman,

  TeamViewer is a third party software. For support on the use of this product go to TeamViewer Support Center.

  Note:   software use of third parties, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

• Failed to start Remote Access Connection Manager Service. Get the 20 error: the system cannot find the specified device.

  This seems to have started with the last batch of updates of Windows 7 (including SP1).
  I can't connect using dial-up.  Get the message:
  Cannot load the Remote Access Connection Manager service
  Error 711: The operation could not complete because it could not start the remote access connection manager service
  in time.  Please try the operation again.

  When I try to start the Remote Access Connection Manager service manually, I get the message:
  Windows could not start the service on Local computer remote access connection manager.
  20 error: the system cannot find the specified device.

  My phone displays the modem works properly, and telephony and the Secure Socket Tunneling Protocol service started.

  I don't know what else might have changed.

  Hello Vince_867,

  Thanks for your post.  Take a look at this thread for a possible solution to your problem.

  See you soon

• Why can't I start Remote Access Connection Manager

  I am not able to connect to internet using my 3G Broadband. I try to resolve the status of the remote access connection manager to "on the road", but the error message invites up to said "Windows could not start the service on local computer remote access connection manager. Error 1068: the dependency service or group could start. "I find the dependencies are Remote Access Auto Connection Manager, routing and remote access, Sharing (ICS) to connect Internet. I tried to put those 3 to "started", but was able to start also.

  Hello
   
  You must make sure that the underside of services are started and restart your computer and check if the problem is resolved.
   
  To start the services.
   
  1. click on start.
  2. type Services.msc in the search box and click on enter.
   
  Note: the common addiction for "Remote Access Connection Manager" and 'Remote Access Auto Connection Manager' is 'Secure Socket Tunneling Protocol Service'.
   
  Make sure that you check the properties of service no matter what you try to start, then click the dependency tab and make sure that you select the dependency registered under this service services.
   
  The dependency of 'Remote access connection manager' services include:
   
  a. secure Socket Tunneling Protocol Service
  b. phone
  c. Plug-and-Play
  d. remote Procedure Call (RPC)
  e. DCOM Server process Launcher
  f. RPC end point mapper
   
  Make sure that you try to start the Connection Manager Service dependency services automatic remote access as well.
   
  Method 2:
   
  I recommend you to update the drivers and see if it makes a difference. You must be logged on as administrator to perform these steps.
   
  1. open Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager. If you are prompted for an administrator password or a confirmation, type the assword or provide confirmation.
  2. in Device Manager, locate the device, and then double-click the device name.
  3. click Driver tab, then click on set to update driver and follow the instructions.
   
  Try to follow the link provided to update a hardware driver that is not working properly and check the question below.
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Thank you, and in what concerns:
  I. Suuresh Kumar - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  

• AppPortal error: remote access to the server is not enabled

  I'm lost on this one.

  Using the full client of AppPortal on a Win7 64 bit machine (version 8.0 of the customer)

  Double-click the icon, download authenticated - published applications show, then double click a published application, the end user receives:

  Remote access to the server is not enabled.

  This happens only on a single computer

  From this profile of users on the given computer I can MSTSC on the same server without problem

  The error also follows the profiles on the given computer.

  I have closed the Antivirus and Windows Firewall and still can not get this to work.

  Even uninstalled and reinstalled the client.

  From my computer, I can easily log in as this user.

  Customers get automatically configured through an XML file.

  After installation, I tested this laptop and he always gave the same error.

  I ended up him to give me the phone for a few hours.

  Uninstalled the version that was there (build 8.0.0.forget) and scoured the Windows Explorer for all left overs (a little here and there in user profiles and delete).

  Then scoured the registry for expressions; vWorkspace, Quest Software and Provision Networks and remove all instances

  Reinstalled all THE SUCCESS with the new connector to our servers (8.0.306.1427)

  Thanks for the help Dave

• Failed to start remote access service

  Hello

  I get a vps and I install ca and iis and the remote access service

  I allow it as a vpn server

  When I try to run the remote access service there gives me an error

  The Routing and remote access is dependent on the Remote Access Connection Manager service, which could not start due to the following error:

  The dependency service or group was able to start.

  I reslove this problem to run these commands:

  netcfg u ms_sstp

  netcfg - c p-i ms_sstp.

  net start sstpsvc

  net start rasman

  now when I am tempted to throw there gives me this error:

  The Remote Access Connection Manager service terminated with the following error:

  The system cannot find the specified device.

  So what is the problem?

  Thank you.

  Hello

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Microsoft TechNet forum. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en-us/categories

• Remote access over Internet connection problems

  I'm trying to figure out how to get remote access to work via the internet. I used to work and it works very well, but we are also on a local network. I have sent the invitation to someone and the password, but it does not connect. I tried the following:

  • Computer Management / Services / connection manager (manual) remote access & routing and remote access (manual)
  • Windows Firewall / allow a program... / Exceptions / Allow: Remote Assistance & routing and remote access
  • Disabled Norton Firewall

  I have alos got my friend to make sure that its parameters match mine. And I still have no success. Does anyone have other ideas? Alternatively, it won't work because I am trying to connect via the internet?

  Hi nataar, 

  Welcome to Microsoft Answers Forums.

  • What software do you use for remote access?
  • What is the version of Windows installed on the computer?

  If you use Remote Desktop connection in Windows Vista, try the procedure below

  Log your PC computer with an account that has administrator privileges.

  Step 1 open the start menu, right-click on "My computer" and select "Properties". A window with the options and details of the computer opens on your screen.

  Step 2 go to the 'Remote' tab at the top of the window "Properties".

  Step 3 check the box for the option "Allow users to connect remotely to this computer" in the section "Remote Desktop" in the Properties window.

  Step 4: click on the 'Apply' button at the bottom of the window to save the changes and enable the remote desktop. Outside users will now be able to access your computer over the Internet.

  Enabling remote desktop access to your computer

  To activate the Office remote connections to your computer, follow these steps:

  1. Click Start, right-click computer, and then select Properties.
  2. Under tasks, click settings on the remote control and confirm the user account control prompt.
  3. Select allow connections from computers running any Version of remote desktop. (Version 'more safe' only works on using IPSec security, and on these networks business networks, you probably will not be allowed to change these settings in any case).
  4. By default, all administrator-level accounts can connect to the computer. If you want to grant remote desktop access to a limited number of users, click Select users, add, advanced, find now and then find the desired name in the search results section. Double-click it. To add another name, click Advanced and find now again.
  5. Click OK to close the dialog boxes.

  NOTE A password must be set on a user account before the user can connect to the remote computer.

  At this point, you must do two things to make sure that remote desktop has been implemented correctly:

  • Click Start, Control Panel. Under Security, select allow a program through Windows Firewall and confirm the user account control prompt. On the Exceptions tab, find the Office remotely in the list of Exceptions and do not forget, that it is checked. If it isn't, check it out. On the general tab, make sure that block all incoming connections is not checked.
  • Use another computer to test the remote desktop before you get involved in the Internet game. Follow the instructions in the second part of the chapter to open the desktop client remotely on another computer on your network. As the host name, type the name of the computer you just put up. Make sure that you can connect on your own local network before continuing.

  Remote Desktop connection: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/Remote-Desktop-connection-frequently-asked-questions

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.