P2V conversion where the Source is on the remote network?

Similar Questions

• Can I use private as Source IPs from a remote network IP addresses while building the IPSec tunnel?

  Can I use private as Source IPs from a remote network IP addresses while building the IPSec tunnel? If not why? If so, how?

  Your explanation is much appreciated.

  Hi Deepak,

  In such a situation, you usually NAT traffic that goes to the internet, but exempt traffic that goes through the VPN, because it will be wrapped in packages with public IP (tunnel) addresses. You can use the same IP address on your interface in the face of internet for the NAT/PAT and source of IPSEC Tunnel.

• Cisco ASA 5505 unable to access the remote network

  Hello

  I have a Cisco ASA 5505, with 50 basic license, which is connected directly to the Modem cable with a public IP address. I have configured and active VPN on the outside interface. When connect us, we connect well without error, but we are not able to access all the resources on the remote network.

  ASA IOS version 8.2 (5)

  Remote IP network: 10.0.0.0/24

  VPN IP Pool: 192.168.102.10 - 25

  I have attached the config: llc.txt

  Please let me know if you have any questions.

  Thank you!

  Hello

  Try adding NAT 0 because inside subnet--> subnet distance

  NAT (inside) 0 access-list TEST

  TEST access ip 10.0.0.0 scope list allow 255.255.255.0 192.168.102.10 255.255.255.224

  HTH

  MS

• Is it possible to stop the conversion through the management network?

  Our management 172.16.0.0/16 network and our production network 10.0.0.0/8

  When we try to make the P2V conversion, all traffic through the firewall that we use for routing between 2 networks, that really is not set up to deal with a lot of traffic and that is what is extremely slow conversion.

  Is it possible to get the converter to push this traffic through the network of production instead?

  the system is 3 ESXi hosts grouped in vcenter 5.5.  Is the storage on a San

  ESX expose NFC (network file copy) as a service that uses a converter to perform conversions and NFC uses the management network. As far as I know, it cannot be changed.

  There is one exception, if--if you do Linux P2V, cloning goes through the network of the virtual machine and you will not have this problem.

  I think you may have a more general with this configuration problem, as the NFC is used not only by the converter (for example, SRM, VMotion, etc...). See this: why vMotion uses the management rather than the network vMotion network?-frankdenneman.nl for something completely different, but which may sometimes cause a problem with this Setup.

  Kind regards

  Plamen

• Can't connect to WIFI on all locations where the WIFI network is available

  Sometimes my computer will connect and detect the networks without wire, Hotels, airports etc. but do not work in the home and in some offices.

  I run put WXP updated with SP2 have an Artheros5005gs adapter. Any ideas?

  Hello

  It is a matter of compatibility between the WLan router and wireless network card.
  If the wireless network adapter does not support the same Wlan standards then you will not be able to establish the WiFi connection.
  Especially the hotspots (Wlan on airports, city, etc.) are not secure and that is why the laptop automatically connects to these wireless LANs.

  The WiFi network at home or in the office is secure for most and you need a right encryption key to connect to these wireless LANs.

  So I think you should check you settings router WLan configuration and usage of encryption right key, SSID, etc.

• How to configure the VPN LAN to access the internet from the remote network

  I have set up for our project site to another Office VPN. Please join.
  Now I have already configured Site to site vpn between ASA 5510 and 1841 router.

  HQ LAN

  Branch of the LAN
                   10.2.1.0/24 > ASA 5510 1841 > > INTERNET < 1841=""> <> 10.30.3.0/24
  ^
  ^
  ^
  ^
  Call Manager
  No. 2851
  Now access from branch LAN LAN of HQ each other.

  I face problems that are
  (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH
  (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?
  (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

  Please give advise me how should I do.

  Hello

  (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH

  Answer:

  You must configure the NAT and crossed to the ASA HQ so that the VPN branch router provides LAN and u-Turn, access to Internet of the SAA.  You must first seup NAT for the branch on the SAA router subnet, then you must type the command:

  permit same-security-traffic intra-interface

  Here's a great example for VPN client hairpining.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?

  Yes, you can

  (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

  You must change your subnet VLANS to be different from the subnet HQ voice phone IP VOice VLAn, it should be fine.

  Kind regards

  Mohamed

• The SDC EPICS to the remote network connection

  I use the DSC to LabVIEW 8.6 and 2009. I'm in California and at the New Mexico I want to connect a server EPICS there. I can read and write using the EPICS of command line, so I know that there is no firewall or hardware connectivity issues. For these programs, I put the IP address of the remote server in an environment variable (add to the EPICS_CA_ADDR_LIST, and EPICS programs then all know here to look for process variables. How to do the same thing for LabVIEW? I tried to sign up for the remote computer in the Distributed System Manager, but that did not work. The remote computer is not running LabVIEW, but that shouldn't really matter. I just need a way to tell LabVIEW to check a specific IP address, and the channel access protocol will take care of everything else.

  I solved the problem in LabVIEW 2009. I added the IP address of the remote system to the SYSTEM (not the USER) EPICS_CA_ADDR_LIST environment variable, then restarted. After that, I was able to access the PVs outside the local subnet. I did not restart after changing the front environment variable. In LabVIEW 8.6 the EPICS of the environment variables have been ignored, but in LabVIEW 2009, they are all used, if it works in the new version.

• P2V conversion where P has a LUN

  Hello

  I need to convert a physical server that has a unit logic with the data number, and I want to convert system (from local SCSI) disk for. VMDK, but need to keep all the LUNS mapped to that server.

  I'll use this method:

  1 - convert physical server with the system only disk.

  2-map LUNS as RDM

  Issues related to the:

  1. what happened with all the data stored in Lun?

  2-if I create a new ROW to use those LUNs, the data are deleted or kept?

  3 - where I find a RDM, creation and usage Documents?

  I'd appreciate your comments!

  Thank you and best regards!

  Patricio

  don't forget to provide points to helpful people

  concerning

• dial the remote network connection

  I use the network by modem to connect to internet.

  My network by modem disconnects automatically after 1 hour due to network problem

  Windows 7 offer me to redial internet dialup network disconnect then property of network by modem windows 8 is not redial function.

  I have to connect by modem network every time when he cut. How to set the automatic reminder in windows 8?

  May be that which may help Windows 8 Redialer

• P2V conversion linux fails with the error. ManagedDiskOpenFault.summary

  Hello world

  I get this really strange/rare error trying to do a P2V converion. The remote Linux server as the local PC Win7.

  gui - log:

  2013-11 - 02T 10: 31:37.409 + 01:00 [12580 error 'wizardController'] Impossible to submit work: converter.fault.ManagedDiskOpenFault

  2013-11 - 02T 10: 31:37.409 + 01:00 [12580 verbose 'Local'] default resource used to "ManagedDiskOpenFault.summary" planned for the module 'fault '.

  2013-11 - 02T 10: 31:37.409 + 01:00 [09512 error 'ConversionState'] Submit job failed: error. ManagedDiskOpenFault.summary

  2013-11 - 02T 10: 31:37.409 + 01:00 [09512 error 'ConverterWizardWindow'] next / finish has failed: error. ManagedDiskOpenFault.summary

  Interesting part of hostd.log on ESXi host running vcenter VAPP and VM is supposed to be created:

  hostd.log:2013 - 11 - 02 T 09: 43:47.912Z [42B81B70 WARNING "Hostsvc.VFlashManager" = spend d733 opID] GetVFlashResourceRuntimeInfo: vFlash is not registered, not supported

  hostd.log:2013 - 11 - 02 T 09: 44:25.009Z [FFC72B70 'Hostsvc.VFlashManager' opID = pass-1011 error user = vpxuser] CheckLicense: vFlash is not registered. error = [N5Vmomi9DataArrayINS_18LocalizableMessageEEE:0xffd76260]

  a bit seems to be him tipping after what the creation of vmx starts point have rolled back again. Records in the trash for a short time a few seconds before the error appears btw.

  VFlush or ManagedDiskOpenFault give me any useful google or forum hits...

  someone told intuitions?

  Thank you very much in advance

  Remo Strotkamp

  Damn! Found the problem thanks to locate you worker journal for me! :-)

  (wonder why it has not been included in the package...)

  The Linux server, I was trying to P2V was our external DNS server. If DNS has not been working so I changed my local Win7 to google.

  Later, I changed our internal DNS to use google instead of our external as the "next hop" and I forgot to change my DNS Win7 config to use our single internal instead of google DNS.

  Now the P2V for my Win7 PC is running...

  Thank you :-) for a ton for your help

  Remo

• Access to the external network when connected to the VPN

  I have a 5505 I successfully install an IPSEC connection to. It uses NT to Active Directory authentication to authenticate. After I log in, I can access everything on the remote network (internal). I can't access anything on the internet.

  Nothing behind the ASA can access internet, vpn clients that cannot come back on.

  Syslog messages show buiding vpn clients to the top and down the ICMP connections if they try to do a ping to the outside, but they are not answered.

  I know it's most likely a statement ACL or NAT that I am out of ideas?

  config attacched

  You have 2 options.

  Split tunneling, unencrypted access to internet.

  Public Internet on a stick, integrated internet traffic to ASA and back on.

  permit same-security-traffic intra-interface

  Global 1 interface (outside)

  NAT (outside) 1

• The remote VPN Clients and Internet access

  I apologize in advance if this question has already been addressed. I am currently using a PIX Firewall Version 6.1 520 (2) running. I have several remote users that VPN for the PIX. Once the VPN tunnel is started, they are more able to connect to internet from their local computers. Is there a configuation on the PIX that allows remote users to have access to the internet when you are connected to the PIX.

  TIA,

  Jeff Gulick

  The Pix does not allow traffic enter and exit on the same interface. Therefore, a VPN user cannot access the Internet through the tunnel. If you use the Cisco client, enable tunneling split so that all traffic through the tunnel.

  If you use PPTP, you can turn off the option that makes the remote network, the default gateway. However, local routes should be added to these clients when they connect.

  Or you can use an additional interface on the firewall. One that puts an end to VPN tunnels and another providing for Internet connectivity. In this way the traffic is not enter/leave on the same interface.

  Of course, it is preferable if the customer Internet traffic does not go through the tunnel. It wastes your bandwidth and has security problems as well. I suggest you use the client to Cisco and the split tunneling.

• Refuse the remote user VPN to access PC using VPN from Site users to partner Site

  Hi Experts,

  Installation program:

  We have configured IPSEC Site - Site VPN between Cisco ASA 5510 and Sonicwall.

  Tunnel is in place and working well, we are able to access the remote workstation to partner and Vis Versa.

  
  

  Requirment: We want to deny remote VPN users, who are our partners access to the workstation.

  Example:

  Remote IP address range: 192.168.200.x/2r4

  Local IP address range: 192.168.10.x/24

  Deny traffic from 192.168.200.x/24 to 192.168.10.x/24

  Thanks in advance

  Kiran Kumar CH

  Hi Kiran,

  You want to deny certain IP addresses of the Remote LAN (of the L2L tunnel), to connect to your workstation?

  Thus, if the remote network 192.168.200.0/24, want to deny some of these machines to connect to 192.168.10.x?

  If this is the case, you can create ACL VPN (VPN filters) on the SAA to restrictive traffic through the tunnel from the IPs.

  Please clarify if I have misunderstood.

  Federico.

• Cisco ASA 5505 remote VPN access to the local network

  I have installed two ASA 5505 VPN site to site that works perfectly.  Now, I also need to have 1 customer site to remote access VPN with Cisco VPN dialer.  I can get the VPN dialer to connect the VPN and get a VPN IP address, but I do not have access to the remote network.  can someone take a look and see what I'm missing?  I have attached the ASA running config.

  Apologize for the misunderstanding.

  To access the remote vpn client 10.10.100.x subnet, the vpn-filter ACL is the opposite.

  Please please share the following ACL:

  FROM: / * Style Definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  outside_cryptomapVPN list of allowed ip extended access any 10.10.20.0 255.255.255.224

  TO:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  outside_cryptomapVPN to access extended list ip 10.10.20.0 allow 255.255.255.224 all

  Hope that helps.

• Where the Clone Source Panel in Photoshop elements 10.0?

  Where the Source of duplication Panel in Photoshop elements 10.0?  I've looked everywhere on here and the internet, all say look under the window and it's there. Well, it's not in mine.  I checked everywhere on it, it is not found. By clicking on the clone button brings it either. I tried to play the video of Jack Nack and nothing will open it on my computer, not that it would be useful because it says to see the window too.  I want a clone of mirror.  I did in previous versions, but never in my 10.0.  I'm on Windows 10.  How to reflect the clone without the Board, or where the "thing" is hidden in 10.0?  Thank you!!

  No version of photoshop elements has a panel of Source of duplication, only photoshop cs3 via photoshop cc 2015 has a clone source panel.

  You can clone or copy the contents into a new layer and then go to Image > rotation > Flip layer horizontal or vertical layer Flip.