Pavilion 15 ab214TX: access point does not (hosted network supported: No.) (Realtek RTl8723BE)

Similar Questions

• Access point does not connect to my WLC

  Hi all

  I have a strange...

  I have 5 AP1000 used to connect to my WLC without problem, now they will not join with the WLC.

  I have the following error in syslog "no Council payload of data found in the join query? I'm also 10 AP1242 who register without problem. Does anyone have any ideas how I can get these babies to join the WLC?

  See you soon

  Colin

  Yes, 1000 access points are supported only on code 4.2... They do not have enough memory to support higher levels of code...

• Connection of comments on the second WNR1000v3 as access point does not connect to Internet

  I have a WNR1000v3 (firmware V1.0.2.68_60.0.93NA) connected to the WAN and it works well. His IP address is 192.168.0.1, subnet 255.255.255.0, gateway 192.168.0.1, mask and DNS servers are on 8.8.8.8/8.8.4.4. DHCP is configured to 192.168.0.10 to 192.168.0.100. I have a guest connection configured and it works well.

  I have a * second * WNR1000v3 (same firmware) bound to the first as access by using these instructions: http://kb.netgear.com/app/answers/detail/a_id/23784/~/how-to-automatically-configure-a-netgear-route...

  I gave him the IP 192.168.0.2, subnet mask 255.255.255.0, gateway 192.168.0.1, and DNS servers again the value of Google. It has the same SSID wireless as the main router and I can move seamlessly between the two. The devices connected to the LAN ports on this access point work very well. Wireless connection works fine.

  I then configured the connection even guest on the second router (the one running in access point mode) and I can get an IP address when I use it. However I can't access the Internet. Ping 192.168.0.1, 192.168.0.2, and 173.194.33.137 (the IP local google.com) all fail.

  Guest connection is not supported on a router functioning as an access point? Or am I missing something really obvious?

  Thank you

  Bill

  @storm1985 I suspect that your configuration means that all the second router LAN ports will also forward only to the Internet. But this gives me a good idea to use another router just like an access point wireless for the connection of comments. (I seem to accumulate old routers.) Unfortunately, I don't have the time to try this out until late in the week, but I'll certainly do and report. Thank you!

• access point does not

  Why the hell is the hot spot of my android bionic phone does not work with my Rt surface Tablet? I have ice cream sandwich on my phone

  I tried again after the update of the firmware and changed the name to my device. It worked last night.

  Problem solved!

• Mobile access point does not

  Well, I'll do that, nice and simple. Since the upgrade to the marshmallow on my Moto X pure on Verizon, I was not able to use my Mobile Hotspot.

  When I allow it, it reads just "Turning hot spot..." "it turns on but it never broadcasts the network name/SSID. I called Verizon to confirm that it is active on my account, and they are in no way the block on my particular line. (works fine on my other 3 lines)

  I do it for a living, so sometimes I need Internet when I'm on a subject. The only way I've been able to do is by attaching my phone via USB, but I prefer to use the hotspot.

  Short of doing a factory reset, someone has suggestions on how to solve this problem?

  Thank you!

  UPDATE:

  The factory reset did work. Kind of painting that I had to do to make it work, but at least it works now.

  Nothing short of a reset, no.

• Access points does not not with WLC

  Hi all

  I have a WLC 5508 in SHIFT mode and 14 1231 WAP connected on it already. However, I still spend my old controller 4404 9 WAP more towards the new 5508 controller. I can't get remaining 9 WAP register with new WLC. I found the rest of the WLC debug message. My WLC license is valid for 50 APs. If any of you guys have seen this? What I'm doing wrong here? Any advance is much appreciated.

  I have install LAG with 2 port departure 8 ports. Do not understand why it gives error of not having sufficient capacity.

  All reviews are much appreciated. Thanks in advance.

  * spamApTask4: 21 May 18:58:29.468: 00:23:04:c9:72:00 Echo Timer expiration: received no response from AP 00:23:04:c9:72:00 heartbeat (10:4:12:26 / 36602)

  * spamApTask0: 21 May 18:58:50.588: 00:13:60:7e:28:30 join priority Processing status = 0, priority of the PA entering 0, MaxLrads = 50, joined Aps = 14

  * spamApTask0: 21 May 18:58:50.588: 00:13:60:7e:28:30 request for discovery refusing AP 00:13:60:7e:28:30 - no AP Manager with available capacity

  * spamApTask0: 21 May 18:58:50.588: 00:13:60:7e:28:30 join priority Processing status = 0, priority of the PA entering 0, MaxLrads = 50, joined Aps = 14

  * spamApTask0: 21 May 18:58:50.588: 00:13:60:7e:28:30 request for discovery refusing AP 00:13:60:7e:28:30 - no AP Manager with available capacity

  * spamApTask0: 21 May 18:59:00.589: BoardDataPayload is not found

  * spamApTask0: 18:59:00.636 May 21:

  * spamApTask0: 21 May 18:59:05.593: BoardDataPayload is not found

  * spamApTask0: 18:59:05.639 May 21:

  * spamApTask0: 21 May 18:59:53.564: 00:13:60:7e:28:30 join priority Processing status = 0, priority of the PA entering 0, MaxLrads = 50, joined Aps = 14

  * spamApTask0: 21 May 18:59:53.565: 00:13:60:7e:28:30 request for discovery refusing AP 00:13:60:7e:28:30 - no AP Manager with available capacity

  * spamApTask0: 21 May 18:59:53.565: 00:13:60:7e:28:30 join priority Processing status = 0, priority of the PA entering 0, MaxLrads = 50, joined Aps = 14

  * spamApTask0: 21 May 18:59:53.565: 00:13:60:7e:28:30 request for discovery refusing AP 00:13:60:7e:28:30 - no AP Manager with available capacity

  Suppose that the CSD has been corrupted...

  Run the command "debug pm pki enable" on the WLC, copy the SSC and stick it on the WLC and see if that helps... Here is the link to do the same thing!

  http://www.Cisco.com/en/us/products/ps6366/products_configuration_example09186a00806a426c.shtml

  Let me know if that answers your question and please do not forget to note the useful messages!

  Concerning

  Surendra

• Access point does not not in Internet Explorer

  I created a page that contains hot spots on this subject with links to other pages. Hotspots work fine in Safari and Netscape, but not at all in Explorer. All the ideas that I was wrong?
  
  Jody

  It seems to work fine in the PC, but I have a Mac and cannot get the links to work.
  I do know not why this extra code is there, but when I deleted it, the links in Internet Explorer on my Mac worked flawlessly
  I do not do things well html, simply use Dreaamweaver to do the work.
  Thank you
  JO - D

• WRT150N access restrictions does not

  Good day everyone.

  I read the messages that are similar to my problem in the forum, but none of the suggested solutions solved my current dilemma.

  I use a WRT150N with firmware v1.00.5. I have a setup of Linux with Squid, connected to the network with the modem router 192.168.23.254. The WRT150N has a gateway of 192.168.23.1. The WRT150N is also connected to an Apple Base Station that serves as a Point of access for users of WiFi.

  Squid limits access to the IP addresses listed under the passerelle.254. But once I change my gateway to 23.1, everything is accessible. I want to block sites as well as on the WRT150N. But whenever I try to put a new restricted access, it does not work.

  

  I put in the IP addresses on which to apply this restriction:

  

  It ignores addresses is because addresses are reserved. I click on save settings here and I save the settings again on the home page.

  Whenever I try to test on the addresses given, I can still access the pages. Is there something that I am missing?

  Thanks in advance for your answers.

  Try to update / re Flash the firmware of your router.

  Connect computer with the Ethernet cable to the Ethernet port on the router.

  Download the firmware on the Linksys site.

  Open the router configuration page.

  Go to the tab Administration and go to the update of the Firmware tab sub.

  Browse and select the downloaded firmware and update the firmware.

  After the upgrade of the firmware reset and reconfigure the router settings manually.

  And see if that helps you.

• I can't tp perform actions on email or some Web sites because the pointer does not change from a helping hand on all orders at the top of a page - any more down works fine

  In Hotmail, for example, I can open any message in the Inbox except the top one, but then I am unable to answer or to take further action because the symbol of the pointer does not change from a helping hand and clicking on has no effect.

  If I try to open the top message from the page by clicking on the command "Open" is gray.

  If I open the type of web page that has a number of menu items at the top of the page, I can't open anything either for the same reason - something more to the bottom of a page is fine. The type of Web site with menus on the sides can be used for all items except the top menu!

  Help!

  Concerning

  Brian

  The extension of the Yahoo! toolbar and the extension of Babylon have been reported because of this problem. Disable or uninstall the modules.

     * https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes
  

• Portege R500 - TrueSuite Access manager does not work with IE 8

  TrueSuite Access Manager does not work with Internet Explorer 8

  Version:
  Internet Explorer: 8.0.6001.18702
  TrueSuite Access Manager 2.1.23.0

  Any idea?

  Thankx
  Robert

  Hello!

  Which laptop computer and operating system you have?
  And what do you mean with it doesn t work? You get an error message or something else?

  You must give us a little more information. Otherwise, we can t help you my friend.

  Good bye

• "Test batch" entry point does not exist

  Hi Forum

  I'm in the process of upgrading one of our testsystems TestStand version 3.1 to version 4.1.

  The system is started by a Labview application that calls TS by a call from the command line (-runEntryPoint 'Batch of Test' "C:\...) »). However, TS 4.1 does not recognize the entry point "Test batch" (worked well in point 3.1), and I get a box with the error message "" Test batch"entry point does not exist. I checked the entry point exist in the model of sequence file, and if I go into the "Run" menu, I get the choice to run "Test batch".

  I am able to be-run the command, but then I, for some reason, don't you the entire sequence.

  Any suggestions for what I am doing wrong? I am connected to TS automatically with my windows login.

  B.R.

  Martin

  Hello

  There should be a document in \Conponents\NI\Models\... that should give you the basics to different process templates.

  Here are a few other references that can help

  http://zone.NI.com/DevZone/CDA/tut/p/ID/7958

  http://digital.NI.com/public.nsf/allkb/D9E7A0BDDDA2A87886256FD9007598D2
  Check out some related links
  http://zone.NI.com/DevZone/CDA/tut/p/ID/3819

  Concerning

  Ray Farmer

• My hp pavilion elite hpe-204f video does not work

  My hp pavilion elite hpe-204f video does not work so I replaced it with another video card that worked. After installing the card and start the system I saw the video on my monitor. Great! I need to replace my video card. No problem.

  Afer by purchasing and installing a new video card, I have no video. I put a new one in another computer. This works. I put the video card which worked yesterday... that did not work.

  Then, I put the original video card that I thought that did not work on another computer and Yes... it worked.

  Should I assume that I have a bad graphical location on the motherboard? If so, short of buying the same motherboard is there anything else I can do?

  Thank you very much for the research.

  Hello

  The integrated video processor still works when the video card is removed?  If Yes, then try this memory bootable Diagnostics CD. Download memtest86 iso file and burn the disk using Imgburn.

  If the above is successful, then re - install the map graphic and clear the CMOS.

  Another thing to try:

  A good cable video know.

  A known good monitor.

• I have a HP Pavilion notebook. My system does not detect my sd card and I can't eject. Help?

  Original title: undetected sd eject not

  I have a HP Pavilion notebook. My system does not detect my sd card and I can't eject. Help?

  From my understanding, most laptops allow you to simply remove the SD card back.  Others have a simple spring mechanism that requires you to press the memory card slightly until you hear a "click", similar to a click on a retractable pen, which must eject the card.

• The mouse pointer does not hide when you type, even with the box checked.

  Hello everyone.  I turned on the check mark in the properties of the mouse "hide the pointer during the strike".  However, the mouse pointer does not hide when typing, but instead remains visible all the time.

  No one knows why this happens?  In previous versions of Windows, the pointer should simply disappear when keystrokes are typed, and then reappear when the mouse is moved.  Is not the case here!

  Thanks for any information!

  System details:

  Windows Vista Ultimate x 64 SP1, 4 GB ram
  Intel Core2 3.16 GHz cpu
  NVIDIA GeForce 8800GT with two monitors
  Aero is enabled.

  Hello

  Welcome to the community of Windows Vista.

  1. what application you are working on when you encountered this problem?

  Hide the mouse pointer option allows you only to remove the mouse curzor of
  the focus in the working window so that the cursor does not cover the text or the pitcure you see.

  Make sure that the curzor of the mouse is placed inside the app as you type, as it does not hide the mouse, if it is outside of the application.

  Change the settings of the mouse
  http://windowshelp.Microsoft.com/Windows/en-us/help/efd700f8-bbc0-4F04-9f78-3bdb4bbf47011033.mspx#EKD

  Kind regards

  Technical support of Microsoft-yama.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

  HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

  The battery is dead. When I try to turn on the laptop by plugging the AC adapter does not charge or led power LED does not turn on. But when I press the power button, the power, the indicator flashes and turns off (when power adapter connected).

  (1) I tried the press and holding the power button for 30 seconds after removing the battery & AC adapter / CC.

  (2) I tried to change the power adapter too.

  The problem is that it is.

  Your advice is very much appreciated.

  Thank you best regards &,.

  Zia

  Dear customer,

  Welcome and thanks for posting your question on the Forum of Support HP

  It seems that you are not able to turn on the laptop and tried to solve the problem

  Please perform steps listed to find out if it is a hardware or software problem below:

  1. remove all cables and devices, disconnect them and try to turn on the device

  2. check the LED light situation and ensure the action of the spring button / stop is normal

  3 Exchange with a well known power cord and the AC adapter

  4 Pack no adapters are available, check if the power adaptor is slightly warm

  Note: This will give us an indication that the power adapter could be good

  5. do you know if the laptop was in battery or power adapter when you used the last time

  Note: Make sure that there is no spill of liquid or cutting

  6. check if the Port of the AC adaptor is loose/broken

  Note: If the laptop is not on even with a power adapter well known, this confirms the hardware failure with the system board or power DC Circuit

  Hope this helps for other queries to answer the post and feel free to join us again

  * Click on the star of CONGRATULATIONS on the left to say thank you *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you

  K N R K

  I work on behalf of HP