Pavilion a1102n: BOOT ERROR CAUSED BY CORRUPT BIOS?

Similar Questions

• White screen of HP Pavilion dv5 1002nr start-up and error code lights flashes twice, corrupt BIOS!

  Equipped with a corrupt BIOS, I struggle to try to replace the BIOS of the motherboard.

  The processor is a AMD Turion series.

  Question, can anyone tell me definitively when the BIOS chip is located on the motherboard.  It seems to be next to the RTC battery on a piece of white under layer in the cutting of a transparent plastic layer.

  Also, is this the only way to save the laptop from the corrupted BIOS will not work the POSITION for me to get into the BIOS to try to restore or update?

  It is laptop a grandson and grandpas still inherit this type of problems.

  I'd appreciate any help, instructions or information on this seemingly hopeless situation.

  Thank you

  You are right about the location of the BIOS chip, this is a chip of 8 spindles/leg next to the battery.  The only other option if you are sure it's bios is to replace the motherboard.  The bios chip is on ebay for $20 to $30.  I have the same problem with the same laptop and I think I'll just bite the bullet and replace the motherboard, if the problem was caused by overheating it could have other problems that surface after replacing the bios chip and you will be chasing ghosts.  The motherboard is also on ebay for $ 119 to $ 175, for the moment.  I hope this helps.

• Corrupt BIOS HP Pavilion DV6-6c51sa

  When I try to boot my laptop it just at a black screen and dosent boot up properly. After about a minute of waiting the caps lock light starts to blink in a cycle of two flashes, which is as I'm lead to believe there is a corruption of the BIOS. I tried to restore the bios with a usb key, but nothing seems to happen when I boot the computer laptop now Fn + B or the WIndows key + B.

  I had before the problem had crashes blue screen due to the igdkmd64.sys which according to me is my drivers intel.

  I have the HP Pavilion DV6-6c51sa, and it runs windows 7

  Hi Drewett90,

  Welcome to the HP Forums!

  I would like to take a moment and thank you for using the forum, it's a great place to find answers. You have the best experience in the HP forum, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I understand that you may receive a blue screen error 'igdkmd64.sys', but now you get a black screen and the caps lock flashes.  Here is a link to the computer does not start and the lights blink or the computer will beep.  Two beeps indicate a corrupted bios.

  Here are documents on selected BIOS HP Application is damaged or missing and restore the BIOS to help this difficulty.

  You can download the update to the bios of HP Pavilion dv6-6c51sa Entertainment Notebook PC Drivers.

  You can also try this.

  At the start, press the F10 key to access the bios.

  Please note on the bottom of the window F9 default installation please select and click Yes. He must try to load the default settings.

  If you are able to load Windows again, I suggest The HP Support Assistant to search for updates running.

  Please let me know the results.

• Restart problems, error Disk Boot error, if please install disk and press a key

  Original title: problems of Reboot

  When I restart my computer it say "Disk Boot error, if please install disk and press a key:?"

  Hello

  1. you remember to make changes to the computer before this problem?

  2. have you changed the BIOS boot device?

  3. What is the brand and model of the computer?

  This could be related to:

  · Startup options is not correctly defined in the BIOS

  · A non bootable CD is in your CD player

  · You don't have any boot device

  · You have installed a new hard drive

  · The hard drive is not properly connected

  · Your system files have been infected

  Change the boot order in the CMOS (BIOS) settings so that your disc is the first in the list.

  a. restart the computer.
  b. new computers often display a startup (or boot) menu. In the start menu, choose "Configuration of the BIOS," or "BIOS settings," or something similar.

  Procedures vary depending on the manufacturer of the BIOS. Usually, you must press a key (for example, F2, F12, DELETE, ESC) or a combination of keys immediately after you
  turn on your computer but before Windows starts. If the Windows logo appears, you must try again by waiting until the Windows logon prompt appears, and then stop and restart your computer again.

  c. the BIOS configuration screen appears. On the BIOS Setup screen, choose the option called "Boot order" or something similar. Startup command settings can also be saved
  under "Advanced settings" or something similar.
  d. Select your drive from DVD or USB drive as first boot device.
  e. restart your computer and see if the problem is resolved.

  
  BIOS WARNING: modification of the BIOS/complementary metal oxide semiconductor (CMOS) settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

• Equium A60-157: error caused by device driver

  Hi all

  I try to write my thesis at the moment and am hampered by my laptop! It keeps randomly, which brings to the top of the blue screen of death, then by restarting; When everything is loaded to the top, I get a "serious error" message that says "error caused by the device driver. As far as I know, all the programs I have are compatible... I was advised to restore the factory settings, which I did a few months ago. And I got the BIOS update for my computer. But it is always the case!

  If it helps, the programs I use daily are Microsoft Word, Access, Powerpoint, Internet Explorer and MSN Messenger. I do not run any games high spec (only Minesweeper occasionally!)

  What can I do? Does anyone else have this problem? Any advice would be much appreciated, because these accidents do not help us to my work!

  Thank you...

  Hello

  It's not easy to tell which device is causing the error.
  What you can do is to check the device drivers. Visit the page of the Toshiba driver and check if there is a new version of driver for example graphic driver.

  Also sometimes this error message appears if the module of memory is faulty.

  What you can do is to use the Microsoft Online Crash Analysis.
  Maybe if you can identify this evil s.
  http://www.Microsoft.com/windowsxp/using/Setup/expert/northrup_03october06.mspx

  Good luck

• HP Pavilion g7-1338dx: error in Partition Recovery Windows 7

  I have a laptop HP Pavilion g7-1338dx. I used recently to minimized Image Recovery on my PC for restore Windows 7 after I decided I liked Windows 7 better. The recovery went well, but recently something happened with my recovery partition. All of a sudden, he's really filled and won't start. HP Recovery Manager (C:\Program Files (x 86) \Hewlett-Packard\HP Recovery Manager\Rebecca.exe\) said that recovery of the system (under System Restore) is disabled. He never used to say that. When I decided to make sure that it worked properly, I get boot error code: 0xc0000225. Why would he do that? I don't have any DVD recovery.

  Thank you!

  -me15prg9926

  If you have not done your defined recovery disk you can order here:

  https://h10025.www1.HP.com/ewfrf/wc/mediaOrder?cc=us&LC=en&productOid=5263043&softwareitem=679942-001

• corrupt BIOS dv6 - 6020ca

  I replaced the motherboard on a dv6 - 6020ca and when I restarted the laptop for the first time I got the following error message...

  "Invalid product information ".

  The following product information programmed on the system board are invalid or missing.

  " Card system 00 (a) - product Configuration.

  ... I searched and found a utility to update DMI and updated system of information... no error message displayed during DMI updates.  But when I restarted the laptop, I get a black screen and the 2 flashing of led that indicates a corrupted BIOS all.

  I tried...

  1. remove the battery and pressing the power button for 1 min not followed by a reboot... no luck

  2. removed the CMOS battery... no luck

  3. I tried the HP tools on a USB key doesn't stick with the bios downloaded in the "current" folder... no luck

  .. .all others face this before?

  .. .all recommendations on what to try?

  Solved... followed jayvastani instructions in this post and the laptop is working again!

  http://h30434.www3.HP.com/T5/other-notebook-PC-questions/how-to-use-the-HP-BIOS-update-UEFI-utility/m-p/2451463#M62022

  Thanks to jayvastani for a great text!

• Envy 17-j043cl: corrupted BIOS

  Problem started when my daughter has added a second HD and we have installed Linux on this drive. There is no entry for Linux BIOS boot change the default boot order, and all attempts to make changes only not good for the worst. We tried to go to the legacy mode, which promtped a reboot and the next screen to enter a code to take effect and a prompt for boot options, which never came to the top. When we went back into the BIOS, it shows the inheritance is always disabled. Enabling secure boot restarts even in a code to enter, but this also fails. Currently, we have tried to activate either (secure boot and legacy are disabled). Win 10 defective ACPI_BIOS_ERROR before secure boot disabled. We can enter the BIOS and go to Boot Options, navigate to the file boot firmly his Linux and efi. Linux works fine, we were not able to boot on a Windows 10 DVD to try to repair Windows 10 and at this point can't get secure startup, or legacy startup to activate. We also tried allowing only an administrator BIOS password but no change, still unable to activate.

  We tried F9 to restore the default BIOS, no change. We tried the menu to restore default BIOS, no change. We have tried, perhaps thinking that something has corrupted the BIOS, to level or to reflash the BIOS with BIOS version even. F.66 currently. His ID card system is 1965. The problem with all BIOS download for its Touchsmart from HP Envy 17-j043cl and unregistered is they don't have that file system board BIOS code 1966 1961, but hers is 1965. Without an exact match, we at our end to get this matter resolved. Any ideas? This sounds like a corrupted BIOS? Why does it seem impossible allow a secure start or inheritance? Is the boot options locked so as to only allow to boot Windows normally from the BIOS? Pointers or other ideas to help are appreciated.

  Joe

  Yes! It is fixed. Inside the interface EFI partition was the 01966.bin file, the last touch to this riddle. We were able to reflash it to the same version, F.66, USB, we had created since the softpaq (sp73289.exe), via the system, firmware management Diagnostics. It flashed fine and then started right Windows 10, so nothing on the disk hard Windows has been tampered. We'll put to start first at openSUSE 42.1 Leap and may start in Windows 10 in the Menu of Grub easier than playing with BIOS options each time.

  Thank you, DoughJohn, for all your help.

• I have a compaq presario cq60 with vista which was able to start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. What can I do?

  I have a compaq presario cq60 with vista. Could not start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. I took the hard drive and installed in my office. Windows Explorer displays the main and recovery partitions.

  The primary partition has the following folders (including hidden & system)

  The recovery partition has the following (including the language files more)

  Someone at - it ideas why my laptop does not work?

  Thank you

  Greg

  Hello

  You press F11 on startup with a HP Compaq to start the recovery process.

  For problems with the recovery process, you will need to contact HP.

  BIOS problems:

  There are messages for the HP Forums for posters with similar errors:

  http://h30499.www3.HP.com/T5/notebook-HP-ProBook-EliteBook/notebook-HDD-problems-TEst-status-1-07-fail/TD-p/658902

  http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-dv8000-getting-1-07-fail-error/TD-p/883284

  http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-notebook-dv6000-1-07-fail/TD-p/1069457

  All the answers it point to a drive about to fail

  See you soon.

• How can I fix corrupted BIOS? tx2500

  My tx2500 gives the double LED flash that signals that a corrupt BIOS.  According to this URL you can 'restore BIOS backup shipped (jumpers).'  If anyone has any idea what that means and how to fix my computer, I would be very grateful.

  Here are two possible ways to restore this BIOS:

  =====================================================================================

  Option: see if your system can restore the BIOS:

  Select your laptop in this list of tx2500 series

  Reach:

  Solve a problem > (vivid RAM) memory / motherboards / BIOS > BIOS / UEFI > restore the BIOS

  For example, if the HP Pavilion tx2500 CTO is your laptop, then this is your Page: restoration of the BIOS

  ---------------------------------------------------------------------------------------------------------------------------------------

  -Option Use UEFI environment to restore BIOS

  • Go fill stop condition (all).
  • Press the power button and
  • Immediately press the ESC key to enter the "Start Menu"
  • Select "F2" to open the advanced systems HP Diagnostics menu screen
  • Select the BIOS / Firmware management

  --------------------------------------------------------------------------------------------------------------------------------------

  Option - Download the BIOS of your laptop Web page - software file and downloads section

  • Extract the contents and put the files on the root of a USB key
  • Connect the USB key to a USB 2.0 on your system
  • Plug the power adapter.
  • From a complete stop condition (all off).
  • Press the power button and
  • Immediately the Windows key while tapping the button 'B '.
  • The process of updating the BIOS should start
  • Follow the prompts to restore your BIOS, use the BIOS file on your USB

  THANKS to erico

  for this information!

  Also erico:

  There are another thread here in the forum where it is covered. There are a few in the wire between the members, but there is also valuable information there.

  ===================================================================================
  

  I hope this helps!

• receive a boot error @system - 8.1 Win, 64 - bit

  receive a boot error @system - 8.1 Win, 64 - bit

  I started getting an error at startup of the system-

  updaterstartuputility.exe - generates an error

  point to a problem with -.

  c:\Program files (x 86) \common files\adobe\adobegcclient\adobegcclientupdater.dll

  (condensed verbiage) said this may be caused by the application that is not designed for windows or another error.  try to uninstall and reinstall.

  What product / program is this and what needs to be uninstalled and reinstalled/downloaded?

  apparently the .dll file above has been updated on 25/11/2015.  This coincides with the start of the error.

  BTW - what is GCCLIENT?

  Hi Js1209500,

  Please refer to the thread below, similar has been discussed there:

  What is AdobeGCClient.exe?

  Error: Client Application to Adobe GC works nicht mehr

  Let us know if that helps.

• Satellite L505-13Z - BOOT error

  Hi all, I have a Satellite L505-13Z. After the hard drive recovery, something went wrong and I had only the F12 page.
  I used the recovery DVDs. It worked for an hour to install win7, then he did a reboot and I saw the windows screen, so that it starts again and stopped working: whenever I turn it on, I have the F12 screen, choose a place to start. Hard drive is detected, but if I choose what it I got the "Boot error" and back to the same page.

  I would try Hiren boot to check if the hard disk is OK or not. How will I know if it's only the hard drive or something else?

  Thank you

  UPDATE.
  I used a bootable cd with Hiren and each test on hard disk and RAM are OK, no errors.
  I inserted the DVD to see if he had the option to repair an installation, but do not, so I installed again. In the end, we asked me to remove the DVD and restart; I did and I went to loop: win 7 was updating registry, reboot, win 7 has been updated to register...

  I wondered if the DVD has been damaged, but is no way to download from microsoft, a Windows 7 copy, because when I insert my response series is to ask the supplier...

  What can I do?

  Posted by jazzrock71
  

  Hi all, I have a Satellite L505-13Z. After the hard drive recovery, something went wrong and I had only the F12 page.
  I used the recovery DVDs. It worked for an hour to install win7, then he did a reboot and I saw the windows screen, so that it starts again and stopped working: whenever I turn it on, I have the F12 screen, choose a place to start. Hard drive is detected, but if I choose what it I got the "Boot error" and back to the same page.

  I would try Hiren boot to check if the hard disk is OK or not. How will I know if it's only the hard drive or something else?

  Thank you

• Equium A60 - error caused by the RAM problem - Windows tool does not work!

  Hi all

  When closing my laptop, I got the blue "screen of death" and it restarts, windows came with this analysis of the accident: "error caused by the memory problem to live: run the Windows tool". I downloaded diagnostic tool (mstinst.exe), he opened so I got "windiag.iso" and he burned on a CD like they told me (the use of 'Record Now') and then I put in the CD drive and rebooted my computer. But it did not launch the tool! Does anyone know why it went wrong and how can I make it work? Even if I got the tool to work, I would be able to solve the problems of RAM anyway, just taking my laptop to a repair center?

  Thanks :)

  Hello

  I put t know if you have seen this page http://oca.microsoft.com/en/windiag.asp but there you can find a detailed explanation of how to use the Windows Memory Diagnostic tool.

  Good luck!

• p6110y (aba): corrupt bios

  corrupt BIOS, hard drive not detected.  Bios F10 quit screen.  Download sp46442.exe update of the bios.  Rename ben.43 to HPBIOS.ROM.  At this point, I'm stuck.  Already create a usb bootable back.  What the bios flashing utility program are used?

  Read the previous comment about just bios make me confuse.

  Hello

  Just give it go as I have suggested. Insert the CD containing the rom file renamed and shut down the PC. Now turn on. If the process is going to work, the rom file will be detected on the CD and read in to Flash the BIOS.  If this does not work, then you will need to send it in for repair.  Depending on the age, it may not be worth the cost to do so.

• S10 - 0167 Bios error: no processor update bios found

  Hello

  My G 6483-72 with installed C2D E8400 (2 * 3 Ghz) is indicated as Core 2 6600 2.4 Ghz.

  Setup displays error 0167: no processor bios updates are found

  BIOS installed is 2WKT39AUS, so it should be supporting E8400.

  tried several times to flash new BIOS 2WJY47USA, but got this message:

  -Update fails with error msg "the file mod specified is greater than the allocated size in rom"

  Any tips?

  PLSE advise, thanks.

  Sorry not updated...

  PBL has been resolved by installing the right processor.

  The dealer sells the machine with E6600 instead of the original E8400

  Thnaks for the help