Pavillion 510-p009: unable to connect to 5 GHz

Similar Questions

• Satellite Pro L50 - B - unable to connect at 5 GHz Wi - Fi

  Hello

  I just bought a new Satellite Pro L50 - B and it is unable to connect to the wifi of my company 5 GHz network. It connects well to the 2.4 GHz network, but poor performance on network thaat there.

  Is it possible to get the L50 - B to work in the 5 GHz range?

  Thank you

  Martin

  Frequency of 5 GHz is supported by 802.11 A and 802.11 N
  But if the WLan module is not compatible 802.11 A, then the standard 802.11 N will operate at 2.4 Ghz

  The question is: what are the standards WLan are supported by the integrated WLan module?

  Which module WLan is integrated?

• Unable to connect at 5 GHz - (Nighthawk x 6 AC3200 (r8000))

  Configure a new Nighthawk.

  It is very flakey.

  Sporadically, drops of each device Wifi 5 GHz, reconnection attempts are rejected "incorrect password".

  they can all connect using wifi 2.4 GHz using the same password.

  Leave 5 minutes and everything links back Ok. many devices need a prod to get them to reconnect.

  The only thing I can think now is to restore to the factory and configure everything again.

  Is not at all a good atmosphere on this device.

  My old unreliable wifi router starts to llok very reliable.

  Any suggestions outside back and get a refund?

  Thank you

  but irrelevant.

  It was all signal uses 5 GHz would fall all over the House at the same time - not a problem of 5 GHz range, most of the 5 GHz range are in the same room as the router.

  In addition, none of the articles addresses the issue of unable to open a session in 5 minutes - every time you've tried he would answer that the password was not valid. Then all of a sudden its own volition it would reconnect.

  I managed to stabilize in the long run by clearing 5 GHz-1.

  This problem occurred several times a day.

  Since the workaround, it did not appear.

  This indicates a fault.

  So I returned to the router to Amazon and bought an Asus RT AC3200 it's more expensive, but I have not had a drop out on any device since running it :-)

• Unable to connect 2.4 Ghz on home network

  Get a message that I can't connect to my network of 2.4 GHz, but I am able to connect to the network of 5 Ghz I have Verizon FiOS and I use their Quantum gateway router. Verizon configures the router to separate systems 2.4 and 5 GHz with different names. In recent days, I noticed that I can't connect to the network 2.4 GHz. I rebooted the router a few times. I applied the 10.11.6 updated so I think that this could be linked to the who. Why go to the slower network? My printers are connected to the 2.4 GHz network and for some reason, when I go to the 5 GHz network printers go offline (this not is is when Verizon pushed update firmware to separate networks). So to print I need to switch networks. Also noticed that access to some hardware Plug devices only when I'm on the same network as them. Lots of questions here but hoping someone can help get at least my mac to back on the network of 2,4 GHz. thanks in advance.

  Tom

  FWIW, I also have FiOS and I have been on 5 GHz since its release. I just tried 2.5 GHz and now I can't connect to it either. Might be time for a call to Verizon.

• HP spectrum 13 Ultrabook: Unable to connect at 5 GHz wireless

  Hello

  Is it possible for this ultrabook, the product F4A22PA number #AB4, connect to a 5 GHz wireless network? Because currently, it cannot 'see' the 5 GHz home wireless network while all my mobile devices can. Is it a hardware problem or a software problem?

  Thank you.

  Hello:

  Here is the link to the product for your laptop.

  http://support.HP.com/us-en/document/c04015688

  Next section of wireless connectivity, I see an Intel 802.11b/g/n with card Wireless Smart Connect (2 x 2) technology listed.

  Whenever you see a card with a suffix of bgn wireless, it means that it is a single card band (2.4 GHz) only.

  A dual band Wireless N card has a suffix abgn or agn.

  That is why you cannot connect to the band of 5 GHz with your laptop.  The card is only designed to connect to the 2.4 GHz band.

• ea6300 and CA 580 - unable to connect at 5 GHz - solved

  Using an EA6300 and a 580 AC usb adapter, trying to maximize the speed on a single computer for audio and video streaming.

  In 5 GHz settings so I put the following

  mode network - CA only

  security mode - wpa2/wpa mixed/personal

  Channel - auto

  Channel width - if I put it on auto, I can connect. Eager to maximize my speed I try to set it to 80 mhz, but when I do I can not connect. All I get is a "cannot connect to the network" in windows and in the settings page of linksys a big bubble appears saying it does not find the router.

  I have therefore to connect the 2.4 ghz and set the width of 5 mhz of back to the car.

  I specifically bought the linksys ac580 I thought that he would play well with the linksys router.

  While I get good speeds in auto mode, I received almost identical speeds using an Asus RT-N56u with an Asus usb n-53. I also have the same speeds now if I use the usb - 53 with the linksys router asus - good enough beating the purchase of $60.00 of the AC-580.

  I'm only a room away from the router so the intensity of the signal is not a problem. I show 4 bars on the signal strength.

  Any suggestions on why I can't use the bandwidth of 80 mhz?

  I want it too fast can I get it maybe I'll use this high audio and video streams to my projector

  Thanks for any info.

  well, I think I've solved it. I changed the security mode to wpa2 just personal instead of the joint and it doesn't seem to work now.

  Down side for me is - for video, in addition to movies from my computer, I also run a hopper of dish and it seems that the hopper is maxed out when I was just with the setting of 2.4 ghz.

  I was getting between 8000-8500kps even on the context of the 5 GHz and 2.4 ghz / 80 mhz - but this is a limitation of the hopper because it's not that, not a problem of linksys.

  I'm thinking just because no one else has an AC adapter / CC, then at least when I stream video of the hopper etc. I'm the one on it instead of having to share with another user.

  in any case... If anyone has problems, check the security settings, although don't know why it would work in auto but not 80 mhz only

• Unable to connect to app store after iOS iphone 10 6 update

  Hello

  Since the upgrade to IOS 10 my iPhone 6 with stubbornly refuses to connect to the App store. The error message is "unable to connect to the app store, try again."

  The phone is connected to the internet (I can surf and send emails) by wifi. Turn off the wifi and the use of mobile (cellular) only link cause the same error. I also did a reboot hot and cold, without result.

  Any suggestions?

  Thank you

  Bill...

  ANSWER: this theme has the best 3 options. In my case, I had to sign out and in the app store of settings, iTunes and app store. Fixed

  PLE-3598048 http://www.Macworld.co.uk/How-to/iPhone/What-do-If-You-cant-connect-App-Store-AP.

• Just updated to IOS 10.0.2 and unable to connect using Store.Please App!

  Just updated to IOS 10.0.2 and unable to connect using Store.Please App!

  Harry

  Hello

  Go down to itunes apple ID page homepage remove ID, then reconnect again.

  See you soon

  Brian

• Unable to connect on the Messages or FaceTime after upgrading to Sierra

  Good afternoon! After upgrading my MacBook Pro (13-inch, mid 2010) to macOS Sierra (10.12.), I am unable to connect to Messages or FaceTime. They worked fine before the upgrade.

  • Messages: After entering my Apple ID and password, I get the message "Could not sign in iMessage." "Could not sign. Please check your network connection and try again. "or"an error has occurred during authentication. "My network is connected to the network (where this message), and the password is correct. Also, I have generated a password app specific to Messages. Enter just grew the message "your Apple ID or the password is incorrect." Messages is works well with my Google Talk and AIM accounts.
  • FaceTime: After entering my Apple ID and password, the engine just turns and it never connects me. Similarly, I have generated a password app specific but use it just gets the message, "your Apple ID or the password is incorrect."

  No idea how I can regain access to these applications? Thank you!

  Reached out to the Twitter account of Apple Support. He proposed to restart. It worked.

• Unable to connect to my yahoo home page after updating iOS

  Unable to connect to my yahoo home page after updating iOS 10

  Hello. Have you tried to remove data from the site under settings > Safari? Could you describe the problem a little more in detail? What happens when you go to the site? You get a login screen? It takes your input?

• Unable to connect to State Bank Anywhere App on my IPhone 6 + after upgrade to IOS 10

  Unable to connect to State Bank Anywhere App for my IPhone 6 + after upgrade to IOS10. Tried uninstalling and reinstalling, but to no avail.

  Contact the developer of the app. They probably need to update the application to ensure compatibility with iOS 10

• Unable to connect to Airport Extreme after updating iOS 10

  Hey guys.

  OK not sure if anyone else has this problem, but I can't connect to my Airport Extreme update IOS 10 my wife is.

  We all have two iPhone 6 and 64 gb & update at the same time.

  We have an ac 802.11 Airport extreme also an extreme dual band of airport & an express airport which none of us can connect to.

  We can connect to the Home Hub 6 provided by our service provider broadband with no problems but it is only in a part of the House that we are unable to connect to my office or at the back of the House.

  Tried resetting the network settings on the phone thought I might ask before having to try to reset back to factory settings base stations.

  Thank you

  FWIW, I upgraded my iPhone SE 5 and Pro iPad to iOS 10 as well, but knows me not any problems connecting to one of my base station AirPort to Wi - Fi.

  Or the other of your iPhones must all problems connecting to other networks in addition to the Home Hub Wi - Fi? In other words, are they only having problems connecting to your AirPort base station? If Yes, do you have someone nearby who also has an AirPort wireless network that you should check your iPhones with?

  In the meantime, let's take a look at the current configuration of your network. We know that you, at least, three airport base stations. What is the exact models of non - 802.11ac extreme and Express?

  These base stations are all linked back to the Home Hub with Ethernet they are all configured for a mobile network?

• Unable to connect to the App Store since the upgrade to IOS 10

  Tried to restart App Store and phone. changed the password and recorded out and back in but still unable to connect. We will, get apps but when I try and download it keeps asking for the password and say that it can not connect. Someone at - it advice?

  Hello CT05,.

  Please ask for assistance with the App Store here in Apple Support communities. I understand how it is important to be able to download my new or existing applications on the App Store. Please try these things to see if we can get this to work for you as expected!

  The first thing we want to make sure is that all your data is safe. You can perform a backup to iCloud or iTunes. Use this article to help with this: backing up your iPhone, iPad, and iPod touch.

  Once you have your backup, please go to appleid.apple.com on your computer or via a web browser. Log in with the Apple ID you are trying to connect to the App Store with. If it connects, take note of the Apple ID and password. Try the same information on the iPhone.

  If this still does not work on the iPhone, please click Settings > Wi - Fi and turn Wi - Fi off. See if you can access the App Store on your cell data. If you can, it means that it some security on the wireless network that you are connected to that is blocking your connection. You won't be able to do this unless you use your cellular data or move you to a new wireless network.

  If you are not able to access the App Store on cellular or wireless data, please open this help article: If your iPhone, iPad or iPod touch connects to a Wi-Fi network. Check the section still not 'connect?' and look at the instructions to reset the network settings. What this does is actually reset some of your default network settings. You have to reenter your password to connect to wireless networks once this is done. Try again.

  Thanks again and have a great rest of your day.

• Unable to connect to the App/iTune stores

  Since the 10 update on my iPhone iOS 6s; When I try to open the App Store or iTunes Store, it says "unable to connect".  If I'm real quick when I open the App Store I can successfully hit a button update B4 I get the Error Message.  It tries to open the iTunes store when I try; but without success.  Everything works fine on our iPhone 5 s and my Mac.

  Ok..

  Try here > If you can not connect to the iTunes Store - Apple Support

• I could not update or install applications for weeks, so I disconnected my Apple ID and rebooted the phone but now I can't reconnect! The error is: unable to connect to the iTunes Store. I should w8 for ios10 and hope that it will be fixed by the new ios?

  I could not update or install applications for weeks, so I disconnected my Apple ID and rebooted the phone but now I can't reconnect! The error is: unable to connect to the iTunes Store. I should w8 for ios10 and hope that it will be fixed by the new ios? Cause don't want to reset my phone.

  You have tried: If you can not connect to the iTunes Store - Apple Support ?

  And I tried to do a soft-reset/reboot the phone?