PC Pavilion 500: Wake Mode

Similar Questions

• HP Pavilion 500-369: prob inherited from the bios!

  I just install a new video card in my hp Pavilion 500-369 its r7 sapphire radeon 265 and a 600watts power when I turned on it beeps 6 times... and I tried all sorts of tricks to youtube... tried to change my bios in legacy mode but I can't find it... plss help

  More recent versions of the UEFI suport Sapphire cards if it is stated in the specs on the website of the company. Perhaps you should consider returning and its replacement by a new PCIe card.

  Here is the list of specifications to Sapphire in the link below. Notice that most of the R9 series supports UEFI. There is no map of R7 series made my Sapphire Tech who take care of UEFI.

  http://www.sapphiretech.com/presentation/product/?CID=1 & gid = 3 & SGID = 1227 & pid = 0 & PSN = 000101 & lid = 1 & leg = 0

  The r7 Radeon 240 by Club3D, r7 Visiontek 250 FF, PowerColor R7 250 2 GB GDDR5 Eyefinity 4 LP Edition (UEFI) all supports UEFI.

• upgrading to windows 7 hp Pavilion 500-096

  I'm trying to find the driver for windows 7 on pc HP Pavilion 500-096. Miss me the network driver, driver Ethernet, USB, PCI driver driver and controller SM. I wonder if someone can point to the compatible drivers for it.

  Thank you

  Hello:

  All the W7 x 64 drivers and software for this model (except the wireless) can also be used on your because they have the same motherboard.

  DO NOT USE ALL DOWNLOADS OF BIOS OR FIRMWARE FROM THIS LINK

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063 & LC = on & CC = US & DLC = in & sw_lang = & Product = 5197679

  Look under the original drivers section.

  SM bus controller is installed with this driver:

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=CP-105638-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5197679 & sw_lang=.

  USB 3.0 is installed with this driver.

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=CP-106223-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5197679 & sw_lang=.

  PCI is installed with this driver.

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=CP-105636-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5197679 & sw_lang=.

  Ethernet is installed with this driver.

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=CP-105642-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5197679 & sw_lang=.

  The of this HP laptop wireless driver should work on the map of your model wireless.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en & cc = us & prodTypeId = 321957 & prodSeriesId = 5229455 & prodNameId = 5229457 & swEnvOID = 4059 & swLang = 13 & mode = 2 & taskId = 135 & swItem = ob-113567-1

• HP Pavilion 500-054: HP Pavilion 500 6 beeps cannot no display

  I have a HP Pavilion 500. I recently went to my BIOS screen and the BIOS did update then my computer shut down. Now every time I turn on my computer, I get 6 beeps and no display. The light stays on and I can hear my fans running, but that's all.

  I didn't change anything in the BIOS before or during this time, I went alone to the screen automatically updated. I have a graphics card in my PC which came with the computer, but this is not a new installation, and has been since I bought (2 years ago.)

  You are not sure if the material breaks and it's a coincidence, or if the BIOS update has messed up my computer?

  Thanks for any help.

  Hello:

  In addition to what Erico posted, you had previously installed a video card no HP, correct?

  Because the product for your PC specification indicates that it came with W8, you would have needed to go into the BIOS, disable secure boot and turn on legacy mode so that the video card working.

  Otherwise you would have obtained the alarm beep 6 just after you installed the card.

  Then... I think that what has happened, is the set of update of the BIOS the BIOS of your computer to its default settings (off legacy mode, active secure boot) and now your video card is rejected.

  Recommendation... stop, unplug the PC and remove your add on video card.

  Plug power on your PC and to go into the BIOS, turn on legacy mode and disable secure again boot.

  Shut down the computer, unplug it and reinstall your add on video card.

  See this link for the BIOS settings need to be changed...

  http://support.HP.com/us-en/document/c03653200/

• Desktop HP Pavilion 500-342nem: can I upgrade my desktop computer hp pavilion 500 with the graphics card AMD RX 480 replacing edge R7

  I plan to upgrade my hp pavilion 500-342nem, who was already A7 graphical 240 with the new 480 RX.

  Is it possible to upgrade both the power supply and graphics card?

  There will be no problem of compatibility (PSU Corsair CX 500 questioned?.)

  I heard a lot of chatter on hp restricting the upgrade of their pc.

  The new card will work?

  Any help will be apppreciated.

  @Jeffrin98, welcome to the forum.

  I cannot find the specs of the product to the computer.  So, here's what you need to do.  Press Start + R from the view of the office.  This will open a run dialog box.  In the box labeled type msinfo32 opened.  In the page that opens, check the option titled Mode BIOS.  If he says UEFI motherboard is supported by the video card.  If this isn't the case, you will not be able to move forward.

  The next step is to measure the space where the card will be installed to ensure that it fits.  Measure from the back i/o port to the front of the case.  This will allow you to see if other ingredients will limit the installation.

  The CX500 Corsair power supply (PSU) should work.  However, check how much power requires the video card.  It may be better to buy a PSU with 600W.  High power will be used during peak power needs.  In addition, the card may require additional power connectors.  Also, I recommend a modular power supply.  It allows you to use only the cables that are absolutely necessary, create better air circulation.  It is very important with more powerful graphics cards.  The heat can be much larger.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• HP Pavilion 500-164, upgrade the video card.

  I replaced the power supply in this area for a graphics card into the PCIE slot. I put a Nvidia 9600 GT in the box, not changed no settings, tried to start, and I get no bios and 6 beeps. Any advice?

  Based on specifications, your desktop HP Pavilion 500-164 has been bundled with Windows 8 installed and has a feature called 'Secure Boot'. You must DISABLE "Secure Boot" and ACTIVATE the standby mode 'legacy' in the BIOS before the computer will start with the nVidia 9600 GT installed.

  Please, remove the video card, make changes to the BIOS and turn off the computer. Then, reinstall the video card and turn on the computer. Your problem should be solved.

  Please see Computer Does starts is not after the installation of a videocard (Windows 8) for more information on the subject.

  If you have any other questions, feel free to ask.

  Please click the White Star of KUDOS to show your appreciation

• HP Pavilion 500-314: big problems by adding an external video card

  You are looking for assistance.

  I recently bought a HP Pavilion 500-314.  Specifications are the following:

  http://support.HP.com/us-en/document/c04293928

  The unit includes the integrated graphics card Radeon R7 and comes with a 300w power supply

  I bought this unit in large part because it states explicitly that "supports PCI Express x 16 graphics cards".  I run a quad-monitor configuration for my work and traditionally did it this using a card ATI over-pants 2450.

  I tried now three different external graphics cards and can get any of them to work:

  First attempt was with a VisionTec Radeon HD 5570 (point #900345).  This card supports quad-monitor configuration and requires a minimum power of 250w.  When I installed the card, the HP Pavilion beeps several times a series of 4 or 5 (can't remember which) emits a beep, but refused to send an image to a video output (either on board or the new card).

  Next attempt was with an EVGA GeForce GT 610.  It's a Setup dual monitor and requires a minimum 300w power supply.  Got the same exact response as with the VisionTec (i.e. the series of beeps... computer would not start all monitors).

  So both of these cards (new), I basically gave up immediately that I couldn't in the BIOS (b/c wouldn't monitors) to see what was going on.  My understanding is that the series of 4-5 beeps usually means that there is a problem of graphics card, or the card that was added doesn't have enough power.  It's frustrating, because the HP Pavilion 500-314 a supposedly a 300w power supply, which is at least equal to the minimum required for each of these cards.

  At this point, I took out the ATI over-pants 2450 my old machine and tried.  This card at least has not caused the series of 4-5 beeps.  Windows has started.  However, once I log in, Windows tries to install the new (card over-pants) repeatedly, only then, the screen flashes and blinks and flashes.  Then I went into the BIOS.  The BIOS indicates that the system recognizes the card, and that the integrated video has been disabled.  However, there is always a signal coming out of the onboard video output (DVI), so it is not in fact actually disabled.  My feeling is that Windows is trying to control two separate video cards (edge + external), which is what causes the problems.  I can turn off the graphics card over-pants w/under Windows (in Safe Mode) and let the card installed, and things work fine.  However, as soon as I try and activate the card, I get endless cycle flashing monitors.

  I spent a few long sessions with HP technical support and they were useless.  They claim that this is not a problem of HP as the embedded video works fine.  I find this extremely frustrating response.  I think it is a matter of HP, because BIOS doesn't seem to be properly disable the onboard video.  Not to mention that the PC can't seem to properly interface with Windows compatible 8 PCI-E cards that claim explicitly require less energy than this unit has.

  I'm usually pretty computer savvy, but have reached my wits end on this one.  I'd appreciate any help anyone could provide.  I tried all kinds of combinations of variables (i.e. enabling integrated video, setting external card at the elementary level, etc.) through the BIOS, but also combinations of w/under Windows, disable integrated video, but nothing is working.

  900345 VisionTek Radeon HD 5570 1 GB DDR3 PCI Express 2.0 x 16

  Big_Dave,

  Thanks a lot for your quick response.

  The first time that I spoke with HP support, they had me disable secure boot.  Unfortunately my problems (i.e. the cards would not install correctly).  However, after reading the link you provided that I was inspired to try things one last time with a new beginning.  I uninstalled all drivers, removed all cards, re-engaged start-up secured, restarted, close, disabled secure boot, reinstalled the cards and rebooted.  And, this time, the system accepts the card GeForce GT 610.

  Difficult for me to express how grateful I am to you.  I spent two weeks and countless hours trying to get this corrected.  Just I found these forums earlier wish.

  WallMonkey02

• Pavilion 500-248eo: HP pavilion 500-248eo

  Hello

  Problems with getting outside windows safe mode. BlueScreen message don't THREAD EXCEPTION HANDLED (atikmdag.sys) SYSTEM.

  By restarting and pressing f5 and f8, trying to get a configuration with the mode menu without failure as a choice as well. I press the recovery of the system in the setup menu, then:

  -Troubleshooting

  ---> Advanced options I have no choice in the settings menu to start, then I go to

  -Command prompt

  His I type this information:

  bcdedit \set {default} safeboot network

  The computer will not enter in safe mode! The message I get in command prompt after which type it is:

  "Specifies the command line is not valid." "Run" bcdedit-? "using the command line.

  I did, but I don't know what is my next move.

  Can someone help me with my next move so I can't get into safe mode? Or is my only option to do a system restore and lost all my files?

  Its your video driver ATI that is the cause, upgrade the driver to the latest version if you can never get started in windows.

  Look under "Graphics-Drivers" and select "Driver AMD graphics card module" download and install.

  http://support.HP.com/us-en/drivers/selfservice/HP-Pavilion-500-200-desktop-PC-series/5399647/model/6923421

• HP Pavilion 500-314: keyboard does not work on startup

  At the start, that the keyboard is not working I have to unplug it and plug it back in

  to make it work. He doesn't do it every time that 1 in 10 starts. The mouse works fine.

  I tried differrent 2 same keyboards. Tried different ports samething.

  HP Pavilion 500-314

  Hello @jwhisenhunt,

  I understand that your desktop computer keyboard work correctly, and that this problem occurs with more than a keyboard. I'd be happy to help you in this case!

  This problem occurs if you start your computer in Safe Mode? Your keyboard is connected to a PS2 or USB port?

  In the meantime, I recommend that you follow the steps described in this document on the wired keyboard (Windows 8) troubleshooting. This should help to correct for non-response of your keyboard.

  Please re-post with the results of your troubleshooting, as well as the information requested above. I look forward to your reply!

  Concerning

• Can I downgrade from windows 8.1 for windows 7 on a HP Pavilion 500-298w?

  Is it possible to downgrade from windows 8.1 for windows 7 on a HP Pavilion 500-298w?

  Can someone direct me to the instructions?

  Thank you

  Hello

  You can buy a license of Windows 7 64-bit.  Buy external DVD media.

  You can find the HP Windows 7 64 bit drivers posted here.

  This document will instruct you on how to disable the UEFI mode and the mode of inheritance.

  Don't forget to create the external HP recovery media before attempting to change the BIOS settings and installing Windows 7.

  Review this article on the 5 different ways to install Windows 7.

• Office Pavilion 500-119: adding an SSD 240gig

  Hi, this is my first post.

  I want to add an SSD, I am looking at a Kingston 240 gig ssdnow v300 upgrade kit.

  I still run the operating system with the already hard drive of 1 t. So the additional SSD will be an extra disk to run VSTs for piano who need the extra speed to run smooth.

  I have the additional available seats in the 500-119 Office Pavilion and the motherboard will accept an SSD?

  He do this upgrade and are there additional changes I have to do after having mounted the additional disk is easy?

  My system is:

  Pavilion 500-119ea

  A10-6700 APU 3.70 GHz AMD

  Any advise will be greatly appreciated.

  Daren-

  TWO part Question and answer.
  ---
  First of ALL, Kingston SSD now v300 240 GB (until 2013) has a SSD Product Page.
  http://www.Kingston.com/us/SSD/v

  There are a LOT of YouTube on Unboxing videos and installation of this SSD Kingston v300.
  Just use your search engine (Google) or the search function in YouTube (Kingston Unboxing v300).
  http://youtu.be/UDmJcgSpTYM

  Here is the Computer Shopper Review (April 4, 2013):
  http://www.ComputerShopper.com/storage/reviews/Kingston-SSDNow-V300-240gb

  ===
  SECOND, your model of PC HP Pavilion.

  Here is the Support page (Internet) to your
  HP Pavilion 500-119ea desktop PC
  http://h10025.www1.HP.com/ewfrf/wc/product?cc=us & DLC = in & LC = in & Product = 6532649

  HP has prepared a number of 'How To' Guides (DIY) on this product Page, like this:

  Adding / replacing hardware
  http://h10025.www1.HP.com/ewfrf/wc/documentSubCategory?tmp_rule=22074 & tmp_task = useCategory & CC = US & DLC = in & LC = in & Product = 6532649

  A lot of your answers lie in the Internet of the above, information provided by HP.
  --
  Let's get down to the potential pitfalls:

  1. your HP computer uses Jasmine-R motherboard (MSI MS-7778) with six 6 internal SATA 6 Gb/s ports. beautiful card mother AMD, many SATA ports. GOOD to GO.
  http://support.HP.com/us-en/document/c03757575

  2. it is a MidTower case, with the hard drive mounted on a Vertical support, bottom left (view after removing the side panel). Follow the Web link below, for this how to (open side panel):
  http://support.HP.com/us-en/document/c04100666

  3. IF you want to add a second drive, in this case a 2.5 "Solid - State Drive (SSD), I see three 3 potential location.

  (A.) mounted horizontally, with support of the adapter in the box below the DVD/CD drive.

  (B) vertically, mounted on the Panel lower front of the computer case.
  A 3.5 "to 2.5" adapter support can facilitate this fixation or the player first itself (using the 4 holes tapped on bottom of SSD) IF the perforations (ventilation, fan, hard drive carrier) line up properly.

  (C.) mounted horizontally on the botton (floor) of the case. Location does not fit all applications.
  The San disk Extreme Pro SSD, I bought in 2014, has been mounting spacer/vibration rubber that could allow this type of editing with a contact adhesive. This montage approach is not appropriate in all cases.

  Selling manufacturers SSD Kits and readers Raw (desktop, laptop)- so working with your store of the local computer for sale retail (££ or €) for a proper selection.

  4. REVIEW the available power cables (SATA style) for their ability to reach these 3 mounting locations.
  Extensions are available from box Mod shops and retail stores.

• HP Pavilion 500-426nc: constant frost of HP Pavilion 500-426nc after the installation of the anti-virus

  Hello, everyone, I really hope someone will give me a few minutes to address this point.

  I started today with the installer of my new PC, a HP Pavilion 500 - 426nc AMD A10-7800 with Windows OS 8.1.

  Everything went well and I was enjoying my new machine speed.

  So I decided to install ESET Nod 32 antivirus. And since then, nothing I can do with my PC: it does not react to my orders, programs will not open and I can't turn it off even properly.

  I read the internet and realized, that I have installed McAfee (or at least a trial version of it) and maybe that's the problem. I wanted to uninstall McAfee, but I don't know how to do it, because my computer does not respond to what I want it to do!

  A few tips on how to get out of this frustrating situation, please?

  I thank very you much for any help.

  Hello:

  First of all, try to get in windows safe mode and uninstall the A / V software that you have installed.

  Enter the mode safe mode with W8.1 is a bit difficult to start the PC, so please read the news to find out how to enter WSM.

  http://www.howtogeek.com/107511/how-to-boot-into-safe-mode-on-Windows-8-the-easy-way/

  Now, if you can get into safe mode, and you can uninstall the A / V software you have installed through the control panel > programs menu, restart your machine and see if it is OK.

  If so, read these instructions on how to safely remove any McAfee software.

  http://service.McAfee.com/FAQDocument.aspx?ID=TS101331

  Finally... my 2 cents on the antivirus programs... why not just use the free A / V software (Windows Defender) that comes with W8.1?

  You will need to turn it on by reading the info on the link below after uninstalling all installed previously 3rd part A / v software

  http://www.fixedbyvonnie.com/2013/10/how-to-turn-on-Windows-Defender-in-Windows-8-1/

• HP Pavilion 500-330 Desktop PC blue screen with the cursor after the start

  I have a desktop computer Pavilion 500-330 Windows 8.1 running on a 64-bit system. The problem is after the start, a blue screen with a cursor appears, and the computer does not go to the lock screen.  I did restore, get updates and even left the only blue screen, but after many hours, he was always there.  If I do a force re-booting, the lock screen comes, but not always immediately.  There is no problem to wake up when it is in "standby".

  Any help will be appreciated.

  Hello again @padway,

  Actually, if you already did a cover of the plant on your computer the problem you describe seems to be a physical problem. Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html. As a recovery plant excludes any kind of software problem this is your best course at this time. A technician from the local computer or a computer repair shop may be an option if you are not in the warranty as well.

  I want to thank you for display on the HP Forums. Have a great day!

• 750TI on HP Pavilion 500-212el GTX

  Hi, could you please tell me if I can pass my computer from a 640 gt graphics card to a gtx 750ti? My computer is a HP Pavilion 500-211el with a 300w power supply.

  Hello

  Don't forget to apply for your PC BIOS post was last updated .   Boot in Configuration of the computer by typing the ESC key to power on and then select F10.  Go to the topics covered and the security configuration and disable Secure Boot and enable legacy mode and save the changes. Restart, and then apply the update to the BIOS.

  HP Secure Boot Windows 8 themes Computer does not start after the installation of a video (Windows 8) card  

  These posted articles HOWTO HP should be useful.

  Some graphics cards NVIDIA GTX 750 require an auxiliary power connector 6 pin PCI-E and that your PC is not a. Try one of the sub models.

  MSI NVIDIA GTX N750 TI and the MSI GTX N750 TF

• Pavilion 500-336: updated drivers audio HP Pavilion 500-336

  Here's the audio that I have on my computer: IDT 92HD65C

  Looking at the Device Manager, I see that the driver date is 07/11/2013.  Where can I find the updated drivers for this?

  The version of the driver I have right now is 6.10.6496.0

  Is there still a good reason do not update the audio drivers?

  Hello:

  The audio works fine now?

  If so, I would not update the driver.  Many problems with W10 and IDT audio.

  There is an audio driver IDT W10 on your PC support page if the Beats Audio doesn't work properly or not at all.

  6.10.6504.0 Rev.A

  http://support.HP.com/us-en/drivers/selfservice/HP-Pavilion-500-300-desktop-PC-series/6879020/model/7127002