Pivotal Satellite Pro 6100 problem

Similar Questions

• Satellite Pro 6100 - problem starting (light flashing Orange)

  On my laptop Satellite Pro 6100, seeing DC IN (first on the left) flashes orange and the laptop does nothing else (no display or sound). The light flashes for 8 times, has a long pause and then starts all over again.

  I tried a different adapter with no joy. It does the same thing if you use only the battery and if you run from the adapter without the battery.

  The only time wherever it shows a different light is when you take the battery out, put back in and hold the power button. Led Slim Select Bay (second right) briefly turns green, but it turns off and the led DC IN resumption of the orange blink.

  It seems likely that it is an internal hardware problem (power supply, motherboard, etc.). Does anyone have any ideas? And as anyone knows anywhere which lists all the different orange light codes for Toshiba laptops?

  Hi André,.

  You are right in thinking that there is a hardware failure (most likely your motherboard). Flashing codes are used by service technicians to indicate the nature of the fault and I have yet to find anywhere who publishes the real meaning of these codes.

  I think it looks like a trip to the nearest Service Agent. :-(

  HTH

• Power on Satellite Pro 6100 problem

  Hello
  I seem to have problems with my SP6100 power. It does not power on battery or plugged it in. The charger flashes, but trying to try to power on - it fails to do so.

  Do you think it is a problem of motherboard or real power in MS? If so, please can someone point to me power supply model number to get a price?

  See you soon.

  You have an older model of Toshiba, then perhaps internal Cmos battery maybe got pretty empty, too.

  I don't think that your power supply has a problem, as you can see a light going ON, on your laptop. I suggest you remove the power cable from your laptop, remove the battery, too (push the cover on the side, so he's going to jump out of your laptop).

  Now, without any connected power source, push the button to empty completely the remains of your laptop. Leave your laptop or else be plugged on it for an hour or two, and THEN reconnect your diet. It can show a message on the screen that the "RTC checksum is false", ignore her and start your computer normally. You will need to set the time through the windows again.

  I hope that your laptop now works like new again ;)

  Concerning
  chain

• [u] [b] Satellite pro 6100 + external projector problems [/ b] [/ u]

  Dear friends,

  I am trying to solve this problem:

  When I connect to the satellite Pro 6100 a 3rd party bCool XG1 DLP projector (a very good) I can see everything fine except DVD.

  I better explain: I can see the movies on the screen of the laptop, but nothing on the wall...

  Notice that I can look at these files directly on the screen, but on the wall...:
  MPEG files (Quick time Yes, but not WinmediaPlayer);
  AVI files (Quick time Yes, but not WinmediaPlayer);
  MOV files (Quick time Yes, but not WinmediaPlayer);

  DVD: (With Intervideo Windvd) Ok on the screen, but no output from the projector.

  Note that if I use the small window mode, the projector output image is correct except inside the window that is displayed in black (but is OK on the screen of the laptop).

  Who can help me?

  Thanks in advance.

  Stefano

  Hi Stefanohf,

  When you pass the output mode you have with keys FN and F5?

  also what settigs are set in the display driver? Right click on desktop, properties and parameters.

  go to advanced and nView. There should be active clone!

  Try this!

  Goodbye, Sam

• Solution found to the problem of "BAD RTC BATTERY' on Satellite Pro 6100

  Hi, I'm from the Italy.

  I myself have solved this problem without changing the motherboard on my laptop second hand satellite pro 6100.

  for info: [email protected]

  Hello

  may I ask how you solved this? I have the same machine and this error pops up sometimes.

  Welcome them

• Satellite Pro 6100 USB problem after stand-by

  Hey all,.

  I have a Satellite Pro 6100 and when that I start my computer, my USB ports work fine. However, as soon as I wake, I get about 6 pop-up messages stating "USB device" unrecognized and my USB ports do not work.

  Device Manager indicates they work fine, so I'm just confused.

  Any help?

  Thank you!
  -Geoff

  Hi guys

  I'm not sure but I think the BIOS update can fix this. Have you already checked if there is a new update of the BIOS for your unit?

• Signal not detected on Satellite Pro 6100 wireless

  I have two laptops Satellite Pro 6100, two of them are configured to automatically connect to our local wireless router which they both started.
  A computer is used by myself by my wife; bookmarks, email accounts and so on are different on every computer/hard drive.

  I have problems with one of the computers (mine) - the usual problem with multispindle connectors on the video boards and feeding, then I tried to use "his" computer with 'ma' machine's hard drive.

  His machine does not recognize our LAN with my hard drive installed. He came up with a new network found, but not a wireless network. Also, with this machine and my hard drive installed, can't the machine to search for wireless LANs, the icon does not appear. The switch is turned on for wireless signals and it works very well with his hard drive in it. The network is protected, and the two machines have the same id in them for connection which work fine in the original engine.

  I don't really understand this condition. Something in the bios? Something on my hard drive that is not recognized by the computer? the wrong phase of the Moon?
  Suggestions how to trouble shoot and fix this?

  Both machines are XP Pro on them, latest updates.

  Hello

  Also AFAIK, Satellite Pro 6100 was equipped with different Wlan cards so if use different HDD with different driver then the Wlan card could not be detected by Windows XP.

  Check if the wireless adapter is listed in the Device Manager and recognized correctly.

• Satellite Pro 6100 - how to change the date and time in the BIOS

  Hello

  I received a satellite pro 6100 that had not been used for some time. Windows does not work then he reinstalled with the good drive.

  When I try and windows 'enable', I get the error 32777 and the laptop is unable to connect with the activation servers that a google leads to believe me that the date and time are incorrect in the bios.

  I know that Press esc to access the bios but there is no option to change the date and time in there. I put the date / the correct time in windows, but this does not seem to synchronize with the bios. I've updated to the latest version of the bios, but this is not enough.

  How can I change or update the time in the bios?

  Thank you

  Hello

  I doubt this time and date setting BIOS does affect Windows activation time Windows doesn t affect it in my opinion. There must be another reason for this problem.
  You can activate Windows by phone?

  Normally the date and time in the BIOS can change you if you mark the date or time, and then press on + or - to change this. Sometimes you have to press PageDown/to the top according to the model of BIOS or laptop.
  Usually in the configuration of the BIOS you will find a brief info how changing the values.

  Check this box!

• Satellite Pro 6100 - code beep at startup

  Hi all

  Just picked up a 6100 Pro of the Satellite with a few problems.

  It lights up, he pointed out the HARD drive and I can hear the disk activity. However, the screen remains blank and a single beep can be learned after 20 sec. White screen, as I understand it, is probably the issue of Council power raging in the SP6xxx series. However, the beep I do not understand.

  I know that 2 beeps or 3 beeps is incompatibility of memory but no one knows which denotes the beep?

  Ta

  Hey Buddy,

  To be honest it's not easy to say what the cause of the problem because it could be everything and Satellite Pro 6100 is old enough for laptop.

  You have two memory modules RAM? If so remove a module. Always try a module only at the same time and test it in the slot of RAM A and B. A module is may be defective or a slot.

  If this is not the case, there seems to be a problem with the motherboard or the CPU itself. If you can exchange these things, try it yourself as a repair would be too expensive for this good old classic I think.
  Second hand spare parts you can get it on eBay s worth a try! ;)

• Satellite Pro 6100 turns off when I connect the power adapter

  Satellite pro 6100 works well up to this I put AC adapter / CC, then turns it self
  Any ideas would be appreciated

  see you soon

  Hello

  You use original Toshiba AC/DC adapter or another?
  What happens if you connect the AC/DC adapter, while the laptop is turned off?

  It s really strange problem, but I think that is s TI associated with AC/DC adapter or the motherboard itself

• Satellite Pro 6100 - no idea on I need drivers

  Hello
  Well, I brought a Satallite Pro off ebay a few days back but I can't find what I need.
  I don't have any idea what the laptop except a Satallite Pro 6100 1.7 ghz, 512 MB ram mobile P4 CPU graphics card nividia.

  It would be great if I could know what laptop that I use to download the drivers, or at least be done in which I need only one I'd love to be able to change the brightness of the display by using the fn + F5 key and have the screen filling the LCD.

  Thank you.
  Mike.

  Hello

  I put t really understand your problem

  The European driver from Toshiba site provides all the important and necessary drivers for the Satellite Pro 6100.

  I assume you mean on the XP drivers
  Install all.

  In a first step, I recommend the installation of the common Module Chip Set Utility, display driver and then continue with the rest

  If you have installed SP2 please check the "Microsoft Windows XP SP2 update information" because some tools need to be updated.

  concerning

• Satellite Pro 6100: black border to the right of the screen

  After a new installation with windows xp when I star tup I have a black border (1.5 cm) to the right of my screen.
  After the beginning and the end of the screen saver, I have a full screen.
  but when my laptop started again I have this black border again.
  I have a satellite Pro 6100.

  Management information
  System
  Model = laptop
  Manufacturer = TOSHIBA
  Serial number = 0000000000
  UUID = ffffffff-ffff-ffff-ffff-ffffffffffff
  BIOS Version = Version 1.90

  OPERATING SYSTEM
  Caption = Microsoft Windows XP Professional
  Version = 5.1.2600 Service Pack 2

  CENTRAL PROCESSING UNIT
  Index = 1
  Manufacturer = GenuineIntel
  Name = Mobile Intel (r) Pentium (r) 4 - M CPU 1.70 GHz
  Version = model 2 Stepping 7
  Max clock speed = 1694
  Socket designation = uFC - PGA Socket

  Display
  Index = 1
  Horizontal resolution = 1024
  Vertical resolution = 768
  Chip Type =
  The RAM size =

  Very strange problem! Can you please tell us more about this problem? I assume that you have installed the OS on your own. Since when you noticed this weird display problem?

  Have you noticed this immediately after installing the OS (without driver)? Did you install the display driver on Toshiba support page?

• Satellite Pro 6100 will not turn on - flashing LED

  Hello

  I have a probelem big, my Toshiba Satellite Pro 6100 lights so I decided to buy a new motherboard @ ebay.

  I have to build in and all I get is an orange error code. So I decide to make me buy a testet PCB (Powerboard) on Ebay, then the same thing! Then I bought a second Geforce but the same error code! So I all exchanged but the processor and I'm ascendant to buy a second to test or do you know Whata´s evil?
  I don't think that the new parts are broken!

  The error, the code of the orange Led is 01000011 or short, long, short, short, short, short, long, long and I did not see what maybe the problem!

  Sorry for my broken English I come from Germany!
  Hope for answers and greetings

  problemman

  Hello

  How do you know what the flashing of led said you? You are a sort of technician? How can you know that the "blink" (long, short) are 0 and 1.
  Do you know how to assemble the circuit board and don't you know that the things you have take care? Who PCB´s that you have exchanged?
  You said:

  Hand and VGA

  but the powerpcb too? And how do you know that the PCB´s are ok? Because why someone is selling you that with the 'work' of description?

  Would appreciate some feedback from you

  Welcome them

• 2 GB card SD not recognized in Satellite Pro 6100

  Hello

  I got a new 2 GB SD card passenger high speed. When I insert into the slot of my Satellite Pro 6100 SD card, I see in the list of the Explorer, the new drive, but when I click it, it says: "Please insert card".

  The card works fine in my Pocket PC.

  What can I do? What is the size limit of card for the SD-Card-Reader inbuild?

  Any help is appreciated!
  Thank you!

  At the point where Satellite Pro has been offered, there was no 2 GB SD card and card reader has been tested with available maps only. If you're lucky, 1 GB card can be readable.

  I think you this card works fine in the other device. There is absolutely no problem with the card itself but old material or even driver for the card reader.

  Maybe in the next few days, someone will point out what card can be used with SP 6100.

• Satellite Pro 6100: screen stays completely white or completely white

  I have a Toshiba Satellite pro 6100 running windows XP with SP2.

  For the last time, when you turn it on, sometimes the screen is totally blank and sometimes she is totally white.

  Must shut down the computer and try to reboot, sometimes several times until the computer starts correctly.

  Could you please tell what it is and how to fix it.

  Your answer will be highly appreciated.
  Thank you.

  Hi, Louis

  I think that we should first find out if the problem is related to the graphics card, for the internal display or on the part of the screen!
  In such cases, it s a good idea to connect the external monitor to the laptop.
  Check if the symptoms appear also on the external monitor.

  If the same thing will happen on the external screen so I guess that the computer laptop s video card is malfunctioning. But if the image appears correctly on the screen then the problem could be linked to the internal LCD display or the small part as FL inverter.

  Check it out