PIX 501 10 User License

Similar Questions

• PIX 501 license

  Cisco PIX 501, offered a license based on the connection: 10 or 100 users. What that means (e.g. for a 10 user license):

  -a maximum of 10 xlates in the nat table?

  -a maximum of 10 connections in the table conn?

  If finally we're true, a user can establish 10 outbound connections (from an ip address). Currently, other users cannot establish a connection outboung?

  Thank you

  Edgar

  "User" is defined as follows:

  -a sent or received traffic via the PIX in the last xlate timeout seconds (five minutes with 501 default config).

  -has a TCP or UDP connection

  -a a NAT session

  -a a session to authenticate user

  It is certainly not the number of connections, but basically, the number of unique IP addresses internal that have any number of connections through the PIX. The 501 will support up to approximately 26000 connections, but only 10 internal IP addresses could use those.

  You can make a "host local sho ' on the PIX to see all the current"users. "

• PIX 501 vs 506th Pix

  I need to make a choice between pix 506 and pix 501.

  I just need to know if I can use the access list in the pix to provide access to a public address 100.

  The address that corresponds to the access list will have access to a service that I put behind the pix.

  I'm not going to use virtual private networks, the only thing I want to do is guaranteed access to the service

  what one do you advise me to use?

  they are almost entirely functionally identical. Avoid any difference in their ability to withstand the ACLs. The 506e has a faster processor, among other benefits, so usually I recommend for those seeking also to a cisco pix 501 50 user.

• Pix 501 license limits and how to say

  I sent a PIX-501-BUN-K9, which is limited to 10 users. I recently sent another PC. I can't browse the internet unless I reboot the pix. Is this an indication that I need to update the license?

  What commands can I run on the pix to check or validate that I reached the limit license?

  You can enter:

  SH ver

  or

  SH - activation key

  This will display your license that is installed on your PIX. Next to "To inside hosts", you will see how many user licenses are available. You can upgrade by purchasing a license from 10 to 50 users (PIX-501-SW-10-50 =) for about $240, or 10 to unlimited (PIX-501-SW-10-UL =) for about $370.

  To find out how many are currently in use, you can enter "sho xlate count" which will set out how current translations are used.

  Please rate if this can help.

• Determination of available on the PIX (10 users) user licenses

  I know that you can log in to the PDM PIX and click on "Oversight" and "Licenses" and see the number of licenses in use user. Y at - it a command line that tells you this same value? I'm looking for some kind of "show user lic" and report to me the number of licenses currently in use, what MAC addresses are machines related to each license, and when those classified.

  Which raises the second question - these licenses client age over a period of time? If so, what are the parameters.

  My third question is how I can delete these licenses. I know I can type "clear xlate" but is there a different/better method?

  Please notify.

  Hello.. Try the local host command local-host/clear show

  "A PIX 501, deforested hosts are released from the license limit. You can view the number of hosts that

  are taken into account within the limits of the license with the local-host command to show. "

  I hope this helps... Please, write it down if she does!

• Connectivity random Cisco Pix 501

  Hello. I'm having some trouble with my CISCO PIX 501 Setup.

  A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.

  My configuration is:

  -----------

  See the ACE - pix config (config) #.
  : Saved
  : Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
  6.3 (3) version PIX
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 8Ry34retyt7RR564 encrypted password
  2fvbbfgdI.2KUOU encrypted passwd
  hostname as pix
  domain as.local
  fixup protocol dns-length maximum 512
  fixup protocol esp-ike
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol pptp 1723
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list acl_out permit icmp any one
  ip access list acl_out permit a whole
  access-list acl_out permit tcp any one
  Allow Access-list outside_access_in esp a whole
  outside_access_in list access permit udp any eq isakmp everything
  outside_access_in list of access permit udp any eq 1701 all
  outside_access_in list of access permit udp any eq 4500 all
  outside_access_in ip access list allow a whole
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  outside 10.10.10.2 IP address 255.255.255.0
  IP address inside 192.168.100.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  history of PDM activate
  ARP timeout 14400
  Global 1 10.10.10.8 - 10.10.10.254 (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Access-group outside_access_in in interface outside
  access to the interface inside group acl_out
  Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  RADIUS Protocol RADIUS AAA server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.10.2 255.255.255.255 inside
  http 192.168.10.101 255.255.255.255 inside
  http 192.168.100.2 255.255.255.255 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  ISAKMP nat-traversal 20
  Telnet timeout 5
  SSH 192.168.10.101 255.255.255.255 inside
  SSH timeout 60
  Console timeout 0
  dhcpd dns 8.8.8.8 8.8.4.4
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  Terminal width 80
  Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
  ------------

  Do you have any advice? I don't get what's wrong with my setup.

  My DC is 192.168.100.2 and the network mask is 255.255.255.0

  The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).

  I have about 50 + peers on the internal network.

  Any help is apprecciate.

  Hello

  You have a license for 50 users +?

  After the release of - Show version

  RES

  Paul

• Pix 501 connection problems

  I am very new to cisco equipment and I was wondering if someone could help me with this (probably very simple question).

  When connecting to my pix via the browser (https://192.168.1.1/startup.html), the browser never took the start screen with the message that says "loading, please wait." This leads me to believe that the firewall is rejecting connections from my machine (which uses dhcp to get an ip address of the pix).

  To work around this problem, I tried to connect to the CLI using hyperterminal. I can connect and run a few basic commands as 'show version', but cannot log on as a user with permissions.

  If the web interface has a default connection of void & empty, surely the cli should be the same?

  Is anyone able to tell me what is the default login, so that I can start confguring the pix via the cli?

  Thanks in advance.

  Justin Spencer.

  Please see below for info pix:

  Cisco PIX Firewall Version 6.3 (3)

  Cisco PIX Device Manager Version 3.0 (1)

  Updated Thursday, August 13 03 13:55 by Manu

  pixfirewall until 12 minutes 18 seconds

  Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU

  Flash E28F640J3 @ 0 x 3000000, 8 MB

  BIOS Flash E28F640J3 @ 0xfffd8000, 128KB

  0: ethernet0: the address is 0011.937e.0486, irq 9

  1: ethernet1: the address is 0011.937e.0487, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  The maximum physical Interfaces: 2

  Maximum Interfaces: 2

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal guests: 10

  Throughput: unlimited

  Peer IKE: 10

  This PIX has a restricted license (R).

  Serial number: 808301473 (0x302db3a1)

  Activation key running: 0xb53be54d 0x26da18f9 0xb2b78cef 0x8fe1abb6

  Configuration changed from enable_1 to 15:36:42.554 UTC, Monday, November 8, 2004

  pixfirewall >

  long live java.

  Please this mark as resolved, others won't waste time.

  Thank you

• Number of VPN clients behind a PIX 501, restriction?

  Is there a restriction in the number of VPN clients can be behind a PIX 501. Is is just limited by the number of hosts (10, 50, Unlimited)?

  Hello

  Behind a PIX VPN clients. Will you use NAT - T (must). It will be limited only to the number of users (normal users) through the PIX. So if you have a license to use 10 or 50 then the VPN connection is counted in this list.

  Connection VPN Client through PIX is not IKE tunnel. They are normal UDP500 and UDP4500 peers.

  Vikas

• PIX 501 NAT / PAT problem

  Have a 501 for a client configuration. All works well for a few minutes and they the PC can't get out the firewall. Looks like the NAT works very well but the PAT do not hit.

  This part of the config, I received an example of cisco.

  Can someone help me?

  Thank you

  Fred

  With less than 25 PCs behind the PIX you won't have to worry about memory problems. You will have to look for good of licensing issues. The default 501 supoprts 10 users license and can be upgraded to support 50 users - still no need to worry about memory.

  Regarding the counters on the PIX, I usually recommend to leave all timers with settings by default unless you are having problems and TAC allows you to change them.

  -Mark

• PIX 501 basic Config

  I'm putting in place an internet service for some members of the service here in Afghanistan. We use the commercial internet (provided by satellite) to a modem that goes into my firewall 501 pix.

  Service that we bought gives us Ip 29, and now I just have it set up as such.

  Modem gateway: 10.124.48.1

  Outside the firewall: 10.124.48.2

  Inside the firewall: 192.168.1.1

  Global NAT pool: 10.124.48.3 30 (the rest of intellectual property s that are outside the package)

  On the inside of the pool of the host: 192.168.1.2 -.33

  DNS for inside customers: 192.168.130.30,.50

  Everything seems ok, as I use the PDM software to allow all traffic ip from outside to inside (I know it isn't the safest to do thing ~ and the fact that I turned a firewall $ 700 to a router for $40). I can browse the internet, but it is really weird.

  I.E.

  I can ping msn.com and www.msn.com , and it resolves the twice,

  But if I put msn.com in Internet explorer, it says cannot display the page, but if I hit the refresh like five times, it'll happen. If I navigate away from the page and then try to type in msn.com again (in the same window) I hit refresh 5 times, to get the next page.

  But if I type in www.msn.com it just generally well upward.

  Even when he says that the page cannot be displayed, I have her pinger running in background ~ so I know that I can get for it. Weird huh?

  I also have a question about licenses. When I get the pix firewall information, it says inside hosts: 10 but he let's have me 32 s ip for inside hosts. Does this mean that I'm having problems when I have more than 10 users browsing through the firewall? Or is that what I have as many hosts ip s?

  Thanks in advance for any assistance.

  1.) to refine the 10 limitation of host within the network you couold install another device inside network that PAT - translation of Port addresses that hide all the IP addresses behind his foreign address.

  All PC-> [device router/PAT] - [PIX Firewall] - [router]-> Internet

  (2.) to buy/pbtain a license longer write a mail to:

  mailto:[email protected] / * /

  The product update:

  PIX-501-SW-10-50 = software upgrade license for 501 10 to 50 users PIX = approximately 340$ US

  PIX-501-SW-10-UL = software upgrade license for the 501 user 10-for-unlimited PIX = about 400$ US

  3.) World normal political deadlock depends on your company security policy, someone should set one, many companys trust their employees and allow all outgoing traffic. Might be good to block traffic P2P, Multimedia Streaming stuff, but this is not possible with OS 6.3.4 Release. You must wait for PIX OS 7.0, which is not available for PIX 501.

  sincerely

  Patrick

• How to configure the PPPoE on PIX 501?

  Mailto: [email protected] / * /

  MSN: [email protected] / * /

  According to the below URL Cisco TAC:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00801055dd.shtml

  but I always failed. And my PIX 501 Configuration noted below:

  pixfirewall # write terminal

  Building configuration...

  : Saved

  :

  6.3 (1) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable password xxxx

  passwd xxxx

  pixfirewall hostname

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  names of

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside pppoe setroute

  IP address inside 192.168.1.254 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route inside 10.0.0.0 255.0.0.0 192.168.1.1 1

  Route inside 20.0.0.0 255.0.0.0 192.168.1.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  VPDN group pppoex request dialout pppoe

  Cisco localname VPDN group pppoex

  VPDN group ppp authentication pap pppoex

  VPDN username xxxx password *.

  Terminal width 80

  Cryptochecksum:xxxx

  : end

  [OK]

  See the pixfirewall version #.

  Cisco PIX Firewall Version 6.3 (1)

  Cisco PIX Device Manager Version 1.1 (2)

  Updated Thursday 19 March 03 11:49 by Manu

  pixfirewall until 58 mins 6 dry

  Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU

  Flash E28F640J3 @ 0 x 3000000, 8 MB

  BIOS Flash E28F640J3 @ 0xfffd8000, 128KB

  0: ethernet0: the address is 000b.fd58.886b, irq 9

  1: ethernet1: the address is 000b.fd58.886c, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Maximum Interfaces: 2

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: 50

  Throughput: unlimited

  you have all the debugging logs?

• Cisco 3640 to the PIX 501 site 2 site VPN performance specifications.

  I intend on creating a site-2-site VPN in Star configuration with a Cisco 3640 as the hub and PIX 501 at the remote sites. My question is around the plug that I read.

  .

  The specifications for a PIX-501-BUN-K9 tell PIX 501 3DES Bundle (chassis, SW, 10 users, 3DES).

  .

  A question is what really "10 users. Which is the limit of the number of concurrent sessions, I have on the VPN at a given time, or that it means something else?

  .

  I also read the specs say that the Maximum number of VPN tunnels that can support a PIX 501 is 5. Because I'm not going to make a tunnel between the PIX 501 at the remote site and the 3640 on the central site, I think I would be OK. Is that correct or is the max value talk the maximum number of concurrent sessions on the tunnel tunnels?

  .

  Thank you.

  UDP traffic always creates a session in the PIX so that the return traffic will be allowed in. The UDP timeout is 2 minutes but IIRC. If you go around NAT with a statement of "nat 0" should not create an xlate I think.

  The real time is hard to say really, probably around 2 minutes for a UDP-only user, you would probably make a few 'local sho' orders on the PIX to really see for sure however.

• Newbie Pix 501 HTTP authentication timeout

  two issues here:

  1. users that connect to the Internet through the Pix 501 ask about every three minutes to enter their user name and password. There must be a setting to change this, my dealer said there is no.

  2. users that connect to the Internet, the first time have their IE session. By clicking Stop and then refresh or House brings to the top of the page. Any ideas.

  Thanks in advance for any ideas you may have

  Jeff Charland

  Jeff,

  First rule is to never trust your seller on technical issues;). Your dealer is wrong. You can indeed change the moment where a user is re - you are prompted to enter their credentials. There are basically 2 parameters, you need to know about the pix regarding delays of authentication:

  (1) the inactivity timer. It's just like that. It expires an authenticated session via the PIX to hit X amount of time without all the traffic. The default timer on the PIX for this setting is 0, which means that we are no period of inactivity by the user (by default) monitor.

  (2) the absoltue timer. Again, is to noise. This timer starts as soon as the user is authenticated and works continuously. When the time is reached, the user is obliged to to re-authenticate when they try to start a new connection (for example, by clicking a link in a web page). The default setting for the absolute timer is 5 minutes.

  We recommend that you do not keep an absolute clock set for security purposes, but for ease of access, you can change these settings. Something like that would not be a 'off the wall' setting:

  timeout uauth 01:00 absolute uauth 0: idle from 10:00

  These settings will force the user to to re-authenticate every hour (absolute) or every 10 minutes after the connection becomes inactive.

  And finally, no idea about #2 above. It happens with all users. Anyone who has tried to Netscape to see if it is a question only IE?

  Scott

• Cisco PIX 501 to Cisco 3005 concentrator via remote access

  Hello people,

  I need your help.

  We got a Cisco PIX 501 in one place and this pix is configured for pppoe connection. The pix connects to internet via the pppoe client. an official ip address ping works well.

  So what I want to do is to establish a tunnel von between this pix and a cisco 3005 concentrator.

  But I failed to establish it.

  Here are the pix config. the acl? s are only for the test and will be replaced if it works.

  6.3 (4) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password xxx

  passwd xxx

  hostname PIX - to THE

  domain araukraine.ua

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  outside ip access list allow a whole

  inside_access_in ip access list allow a whole

  pager lines 24

  opening of session

  Monitor logging warnings

  logging warnings put in buffered memory

  MTU outside 1456

  MTU inside 1456

  IP address outside pppoe setroute

  IP address inside 192.168.x.x 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  PDM location 192.168.x.x 255.255.255.224 inside

  forest warnings of PDM 500

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  outside access-group in external interface

  inside_access_in access to the interface inside group

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  Enable http server

  255.255.x.x 192.168.x.x http inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  255.255.x.x telnet inside 192.168.x.x

  Telnet timeout 5

  SSH 194.39.97.0 255.255.255.0 outside

  SSH timeout 5

  management-access inside

  Console timeout 0

  VPDN group pppoe_group request dialout pppoe

  VPDN group pppoe_group localname [email protected] / * /

  VPDN group ppp authentication pap pppoe_group

  VPDN username [email protected] / * / password *.

  encrypted privilege 15

  vpnclient Server 212.xx.xx.xx

  vpnclient mode network-extension-mode

  vpntest vpngroup vpnclient password *.

  vpnclient username pixtest password *.

  Terminal width 80

  the hub, I created a user pixtest, a group vpntest and I? ve created the rules of the network for example to what server, users behind the pix will be able to access.

  And that? s all.

  I couldn't send you exit pix or hub because I don't have an error or a message that the tunnel will be established.

  What can be wrong?

  Thanks for the replies

  This configuration example shows how to create an IPsec tunnel to a computer that is running the Client VPN Cisco's (4.x and later versions) to a Cisco VPN concentrator 3000 to allow the user to safely access the network inside the VPN concentrator.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a008026f96c.shtml

• Pix 501 problem

  I can not configure a pix 501 as a firewall, I need to know if it comes with a default configuration. I connect the PIX of the LAN and it start´s to DHCP each machine on the network with no problem, but none of the user´s can access the internet.

  I need to know what to do to get access to internet protection and network security.

  Where can I go to configure the Pix, if I really need to configure it!

  Hi... basically, you need the following basic steps to access your internal users to the internet

  If you use 6.3 (5) PIX

  interface ethernet0 100full

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  inside_access_in ip access list allow a whole

  inside_access_in access to the interface inside group

  NAT (inside) 1 access-list inside_access_in

  Global 1 interface (outside)

  NOTE: with the config ablove room your internal users will have FULL access to the internet. If you want to restrict access to only http, https, ftp, dns, etc then you need to change the access list for something like that...

  inside_access_in list access permit tcp any any eq www

  inside_access_in list access permit tcp any any eq 443

  inside_access_in list access permit tcp any any eq ftp

  inside_access_in list access permit tcp any any eq 53

  inside_access_in udd allowed access list any any eq 53

  I hope that helps... Rate if he does!