PIX 501 vs 506th Pix

Similar Questions

• QoS is supported on the Cisco PIX 501 or 506th?

  Hello

  There is no mention of QoS in technical for the PIX 501 and 506 records but nothing for the 515. PIX OS 7.x configuration guides do not mention specific material support.

  Does anyone know if QoS is taken care of in the 501 or 506th - I need support lines expectations for VoIP over IPSec.

  Thank you

  Chris

  QoS is supported in 7.x code, you would have to level 501/506 to 7.x code, but this is not supported on these two models, the next logical solution would be to upgrade your PIX 501/506 to asa5505s.

  Rgds

  Jorge

• Connectivity random Cisco Pix 501

  Hello. I'm having some trouble with my CISCO PIX 501 Setup.

  A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.

  My configuration is:

  -----------

  See the ACE - pix config (config) #.
  : Saved
  : Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
  6.3 (3) version PIX
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 8Ry34retyt7RR564 encrypted password
  2fvbbfgdI.2KUOU encrypted passwd
  hostname as pix
  domain as.local
  fixup protocol dns-length maximum 512
  fixup protocol esp-ike
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol pptp 1723
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list acl_out permit icmp any one
  ip access list acl_out permit a whole
  access-list acl_out permit tcp any one
  Allow Access-list outside_access_in esp a whole
  outside_access_in list access permit udp any eq isakmp everything
  outside_access_in list of access permit udp any eq 1701 all
  outside_access_in list of access permit udp any eq 4500 all
  outside_access_in ip access list allow a whole
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  outside 10.10.10.2 IP address 255.255.255.0
  IP address inside 192.168.100.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  history of PDM activate
  ARP timeout 14400
  Global 1 10.10.10.8 - 10.10.10.254 (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Access-group outside_access_in in interface outside
  access to the interface inside group acl_out
  Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  RADIUS Protocol RADIUS AAA server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.10.2 255.255.255.255 inside
  http 192.168.10.101 255.255.255.255 inside
  http 192.168.100.2 255.255.255.255 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  ISAKMP nat-traversal 20
  Telnet timeout 5
  SSH 192.168.10.101 255.255.255.255 inside
  SSH timeout 60
  Console timeout 0
  dhcpd dns 8.8.8.8 8.8.4.4
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  Terminal width 80
  Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
  ------------

  Do you have any advice? I don't get what's wrong with my setup.

  My DC is 192.168.100.2 and the network mask is 255.255.255.0

  The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).

  I have about 50 + peers on the internal network.

  Any help is apprecciate.

  Hello

  You have a license for 50 users +?

  After the release of - Show version

  RES

  Paul

• Adding a pix 501 VPN 2

  Hello.. I am beginner in this kind of things cisco...

  I'm trying to set up multiple VPN on a Cisco PIX 501 firewall with routers Linksys BEFVP41...

  Since not very familiar with the CLI, I use the PDM utility and it was very easy for the first... Unfortunately, I get this error when I try to add the second VPN using the VPN Wizard:

  Outside_map map (ERR) crypto set peer 200.20.10.3

  WARNING: This encryption card is incomplete

  To remedy the situation even and a list of valid to add this encryption card

  Hi garcia

  for each vpn/peer, you need to a separate instance of crypto card, the card will have the same name, but different sequence... numbers one map encryption can be attributed to an interface, but you can have several instance of cards inside a main...

  for configuration, you can go through the URL below... It has all the details on IPSEC config:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/config/ipsecint.htm

  I hope this helps... all the best... the rate of responses if deemed useful...

  REDA

• Microsoft secondary authority w / Cisco router / PIX 501

  I'm trying to get digital certificates to work on my 2621XM router. I have also

  need to put in place on the three firewalls PIX 501 but who have not obtained until now still. I have

  don't have no access to the CA root, but it could bring in line if I had to. I have

  have a stand-alone Microsoft subordinate CA that I want to use to publish all

  certificates.

  Is it possible, as well with the router and the firewall? If so, what version

  the IOS do I need? I installed the add-on CEP at HQ. I can't

  It works and I'm starting to wonder if it is still possible. If this doesn't

  work, how can I make it work? I have all the documents that Cisco has combed

  on the subject and have gotten nowhere.

  Any help would be greatly appreciated. Thank you.

  Jennnette,

  I sent this document, let me know how it goes or if you have any questions.

  Kurtis Durrett

• PIX 501 Logging

  I would like to open a session of hacking and intrusion of the attacks through a PIX 501 with a connection to broadband in a Home Office Setup. I have the camera upwards and the race and I am currently Setup with the Kiwi Syslog Dameon. What would be my best approach Logging all relevant information with the load to the bottom of the unit? Any suggestions / tips would be appreciated.

  Thank you

  It is a common logging configuration that I use:

  opening of session

  timestamp of the record

  logging trap information

  host of logging inside x.x.x.x

  No registration message 106015

  No message logging 106007

  No message logging 105003

  No registration message 105004

  No message recording 309002

  No message logging 305012

  No registration message 305011

  No message logging 303002

  No message logging 111008

  No message logging 302015

  No message recording 302014

  No message logging 302013

  No registration message 304001

  No message logging 111005

  No message logging 609002

  No message recording 609001

  No message logging 302016

  I usually do not enable the logging buffer (never use connection console it will affect performance) because it's not the messages timestamp (it only timestamps in the syslog). But the PIX loaded down with the load, you and Kiwi you before the PIX don't.

  Also turn on the IDs on the PIX.

  It will be useful.

  Steve

• Configure the PIX 501 for IDS

  I have a PIX 501 with wired high-speed LAN headquarters inside and outside. Which would be a solid policy IDS to enable and what interfaces it must be applied to? There will be other measures necessary to enable IDS?

  IDS on the PIX itself is very limited, it checks only 59 signatures listed here (http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_62/cmdref/gl.htm#xtocid9 under the section of signatures supported IDS). The signatures themselves are pretty basic.

  If you do not want to activate this, then for the signatures of attacks I would fix for drop/alarm/reset action, which is the default anyway.

  You will also need to set the logging to a syslog server and monitoring for any 4000nn messages in syslog, cause it event IDS.

• PIX 501, 1 static IP, IP address dynamic 2. Mesh full possible?

  I have 3 sites. All sites have PIX 501. Central site has a static IP, 2 remote sites a dynamic IP.

  I have no problem with the connection to the central site by using their dynamic IP address in a remote star connection.

  Is it possible for 2 remote sites communicate? There is data that must be transferred between remote sites. I read somewhere in cisco site web which its possible via mesh on request.

  Does anyone have an example of configuration on a VPN Site to Site where the Central site has static IP and remote sites with a dynamic IP? Remote locations teaches a dynamic IP from remote sites to the central server.

  Thank you.

  With IOS as your hub and then the Yes rays, the rays can learn dynamically address other departments using the PNDH. This type of configuration is called Dynamic Multipoint VPN (DMVPN), you can read everything you need to know about this here:

  http://www.Cisco.com/warp/public/105/DMVPN.html

  Even with EzVPN (not DMVPN) the rays will not learn the address of other rays, all communication is always via the hub. Call another talks would work, but as I said, the packages will talk-star.

• How to configure the PPPoE on PIX 501?

  Mailto: [email protected] / * /

  MSN: [email protected] / * /

  According to the below URL Cisco TAC:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00801055dd.shtml

  but I always failed. And my PIX 501 Configuration noted below:

  pixfirewall # write terminal

  Building configuration...

  : Saved

  :

  6.3 (1) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable password xxxx

  passwd xxxx

  pixfirewall hostname

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  names of

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside pppoe setroute

  IP address inside 192.168.1.254 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route inside 10.0.0.0 255.0.0.0 192.168.1.1 1

  Route inside 20.0.0.0 255.0.0.0 192.168.1.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  VPDN group pppoex request dialout pppoe

  Cisco localname VPDN group pppoex

  VPDN group ppp authentication pap pppoex

  VPDN username xxxx password *.

  Terminal width 80

  Cryptochecksum:xxxx

  : end

  [OK]

  See the pixfirewall version #.

  Cisco PIX Firewall Version 6.3 (1)

  Cisco PIX Device Manager Version 1.1 (2)

  Updated Thursday 19 March 03 11:49 by Manu

  pixfirewall until 58 mins 6 dry

  Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU

  Flash E28F640J3 @ 0 x 3000000, 8 MB

  BIOS Flash E28F640J3 @ 0xfffd8000, 128KB

  0: ethernet0: the address is 000b.fd58.886b, irq 9

  1: ethernet1: the address is 000b.fd58.886c, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Maximum Interfaces: 2

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: 50

  Throughput: unlimited

  you have all the debugging logs?

• Opening of port 22 in PIX 501

  I would like to access my PC location xyz. How can I open port 22 access to my pc. I use pix 501.

  Can anyone provide commands to open the port so that I can access my pc.

  Thank you

  totally agree because only 3 commands are needed.

  list of allowed inbound tcp access any eq 22

  public static tcp (indoor, outdoor) interface 22 22 netmask 255.255.255.255 0 0

  clear xlate

  However, all of these commands are missing in the config you have posted.

• Several connections of client XAuth of PIX 506th

  Hi, we have Cisco PIX 506th, fully updated:

  Cisco PIX Firewall Version 6.3 (5)

  Cisco PIX Device Manager Version 3.0 (4)

  We have two customers with Cisco (routers with VPN and PIX firewall IOS). I can't make two IPSec connections for them using XAuth (they allowed Xauth). I see that we have only one VPN connection with extended authentication (XAuth) called "Easy VPN. When I am trying to set up a new one it replaces just my old connection. If I shouldn't use this firewall PIX Easy VPN Client, how can I use extended authentication (XAuth) I found no option for this? Is this supported? At 25 connections how to only IPSec connections without XAuth authentication data sheet?

  as far as I know, you may need an additional device. as mentioned, the reason being a single unit can act as a client for two ezvpn ezvpn different servers.

  Otherwise, you must return to the type of vpn. that is, to set up lan - lan.

• IPSec-manual (without IKE on PIX 501)

  I would like to establish an SA without IKE.

  When I try the commands on the console:

  ciscopix (config) # netcampus 10 ipsec-manual crypto map

  IPSec-manual mode is not allowed in this PIX.

  Type help or '?' for a list of available commands.

  My PIX is a 501 with 6.1 (2), 50 users + 3des.

  I have not found references on this problem in the docs.

  Any tips?

  IPSec-manual is not available in the 501, only in the 506 and upward.

• PIX 501 does support proxy ARP?

  Hello

  I would like to know if it is possible to publish a proxy arp some public address on the external interface of a PIX 501.

  What is the command I should use?

  Thank you

  Hello

  proxy ARP is performed automatically when you use the 'static' command to bind the IPaddress private an internal server to a public IP address.

  Kind regards

  Tom

• VPN with PIX 501

  Help!

  I'm trying to set up VPN on my PIX 501. I have no experience of the PIX and have no idea where to start!

  Any help will be greatly appreciated.

  Thank you

  Bennie

  access list allow accord a

  where is the name of the access list that you applied the entrants to your external interface. You may also allow accord coming out, if you have a list of incoming configured access to your inside interface.

• Cisco 3640 to the PIX 501 site 2 site VPN performance specifications.

  I intend on creating a site-2-site VPN in Star configuration with a Cisco 3640 as the hub and PIX 501 at the remote sites. My question is around the plug that I read.

  .

  The specifications for a PIX-501-BUN-K9 tell PIX 501 3DES Bundle (chassis, SW, 10 users, 3DES).

  .

  A question is what really "10 users. Which is the limit of the number of concurrent sessions, I have on the VPN at a given time, or that it means something else?

  .

  I also read the specs say that the Maximum number of VPN tunnels that can support a PIX 501 is 5. Because I'm not going to make a tunnel between the PIX 501 at the remote site and the 3640 on the central site, I think I would be OK. Is that correct or is the max value talk the maximum number of concurrent sessions on the tunnel tunnels?

  .

  Thank you.

  UDP traffic always creates a session in the PIX so that the return traffic will be allowed in. The UDP timeout is 2 minutes but IIRC. If you go around NAT with a statement of "nat 0" should not create an xlate I think.

  The real time is hard to say really, probably around 2 minutes for a UDP-only user, you would probably make a few 'local sho' orders on the PIX to really see for sure however.