Pix 501 license limits and how to say
I sent a PIX-501-BUN-K9, which is limited to 10 users. I recently sent another PC. I can't browse the internet unless I reboot the pix. Is this an indication that I need to update the license?
What commands can I run on the pix to check or validate that I reached the limit license?
You can enter:
SH ver
or
SH - activation key
This will display your license that is installed on your PIX. Next to "To inside hosts", you will see how many user licenses are available. You can upgrade by purchasing a license from 10 to 50 users (PIX-501-SW-10-50 =) for about $240, or 10 to unlimited (PIX-501-SW-10-UL =) for about $370.
To find out how many are currently in use, you can enter "sho xlate count" which will set out how current translations are used.
Please rate if this can help.
Tags: Cisco Security
Similar Questions
-
Cisco PIX 501, offered a license based on the connection: 10 or 100 users. What that means (e.g. for a 10 user license):
-a maximum of 10 xlates in the nat table?
-a maximum of 10 connections in the table conn?
If finally we're true, a user can establish 10 outbound connections (from an ip address). Currently, other users cannot establish a connection outboung?
Thank you
Edgar
"User" is defined as follows:
-a sent or received traffic via the PIX in the last xlate timeout seconds (five minutes with 501 default config).
-has a TCP or UDP connection
-a a NAT session
-a a session to authenticate user
It is certainly not the number of connections, but basically, the number of unique IP addresses internal that have any number of connections through the PIX. The 501 will support up to approximately 26000 connections, but only 10 internal IP addresses could use those.
You can make a "host local sho ' on the PIX to see all the current"users. "
-
PIX-to-client VPN and how to reach on other interfaces systems
Hi all
I've implemented a Pix-to-Client VPN and it seems works ok.
As you can see, customer gets the same inside the class address (192.168.100.x) so I can reach across systems.
My questions are:
If I give different subnet pool addresses, how can 1 I still reach inside systems?
2 if I have other systems on these interfaces such dmz1 (192.168.10.0) dmz2 (192.168.20.0) how to get to these systems of the
even the client vpn access?
Concerning
Alberto Brivio
IP local pool vpnpool1 192.168.100.70 - 192.168.100.80
access-list 102 permit ip 192.168.100.0 255.255.255.0 192.168.100.0 255.255.255.0
NAT (inside) - 0 102 access list
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp - esp-md5-hmac trmset1
Crypto-map dynamic map2 10 set transform-set trmset1
map map1 10 ipsec-isakmp crypto dynamic map2
map1 outside crypto map interface
ISAKMP allows outside
ISAKMP identity address
part of pre authentication ISAKMP policy 10
encryption of ISAKMP policy 10
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup address vpnpool1 pool test
vpngroup split tunnel 102 test
vpngroup test 1800 idle time
test vpngroup password *.
It is generally preferable to use another range of IP addresses. The PIX will know that the VPN Client uses that vary and route it properly whitch is not the case when you are using the same IP range as the inside interface.
To access another interface use the SHEEP (your ACL 102) access list which disables NAT between the VPN and the neworks to which you want to connect.
Example of config:
access-list allowed SHEEP Internalnet ISubnetMask VPN-pool 255.255.255.0 ip
access-list allowed SHEEP DMZnet DMZSubnetMask VPN-pool 255.255.255.0 ip
NAT (inside) 0 SHEEP
AAA-server local LOCAL Protocol
AAA authentication secure-http-client
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS
Crypto-map dynamic outside_dyn_map 20 game of transformation-TRANS
card crypto 65535 REMOTE ipsec-isakmp dynamic outside_dyn_map
REMOTE client authentication card crypto LOCAL
interface card crypto remotely outside
ISAKMP allows outside
ISAKMP identity address
ISAKMP nat-traversal 20
part of pre authentication ISAKMP policy 10
ISAKMP policy 10 3des encryption
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
IP pool local VPNPool x.y.z.1 - x.y.z.254
vpngroup VPNGroup address pool VPNPool
vpngroup VPNGroup dns-server dns1 dns2
vpngroup VPNGroup default-domain localdomain
vpngroup idle 1800 VPNGroup-time
vpngroup VPNGroup password grouppassword
username, password vpnclient vpnclient-password
sincerely
Patrick
-
I am currently a computer on which I already installed XP OEM and upgraded to the edition upgrade Vista Ultimate retailers through the ultimate steal Microsoft.
[Reminder]
The problem I have is that I've recently updated my graphics card to a card of Nvidia 7300GS card Nvidia GT240 on which my motherboard was properly assessed. However, due to some unfortunate circumstances (I dunno if it's associated graphics or an electrical surge problem, I suspect the latter as the card is fine) my PCI Express slot is fried! This resulted in the motherboard being unable to start any card in the PCI Express slot and gives a series of BIOS beep error codes. I even dug my old graphics (7300GS) and he was still unable to boot. Accordingly, I need to replace the motherboard for the PCI Express slot works if I use a graphics card.
[Problem]
Since the license Vista Retail Upgrade that I use currently is the edition of 'detail', can I simply change my motherboard everything and turn it back on, or is it more complex because it is installed on the high XP OEM that is bound to the default motherboard? What are my options?
I have to buy another XP OEM license and reinstall everything from scratch? What happens if I didn't reinstall and just changed the motherboard and drivers updated my current installation? Is - is this legitimate?
As I understand it, the Windows for OEM license allows a person replace a motherboard of 'default' (GA-M55plus-S3G in my case) for a replacement under certain conditions, mainly as for everything. Am I entitled to it? If so, what motherboard would be I can replace by although it is considered an upgrade? I have in mind an ASUS M4A78L-M as it is cheap and comes with connectors female jack audio 8 channels on the backplate was on my old motherboard.
My main confusion is to know what license applies to me because of the upgrade process, retail of Vista or XP OEM? Upgrades medium I improve my driver's license?
I would like to solve this problem without canceling my licenst but just don't know how?
Thank you very much for any help or advice.
Zemian.
It is not Microsoft.
These are public forums, hosted by Microsoft.
You need to set the XP Reinstall 1 > and then perform the upgrade to Vista.
We cannot tell you what motherboard you can replace it with.
Here is the Vista Forums.
You will have no problem using the Vista Upgrade retail > solve your XP problem 1 in the Forums of XP:
XP forums:
http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP
Link above is for XP Forums.
There is a list of the different Forums XP to the link above to help you.
You get the help you need there.
Here is the Vista Forums.
See you soon
Mick Murphy - Microsoft partner
-
Does anyone know if the PIX 501 10 user license will limit the number of users can cross a site to site VPN that ends at the PIX?
Yes, it does, I encountered a problem with it myself in the past. The page at http://www.cisco.com/en/US/customer/products/hw/vpndevc/ps2030/products_data_sheet09186a0080091b18.html
It is said "the Cisco PIX 501 license 10 users supports up to 10 simultaneous source IP addresses for your internal network to browse the Cisco PIX 501.»
In my case what happened is that we had a VPN site-to-site created with a small office that adds a little more employees, everything was going well until the 11 IP address attempted to connect to a resource across the IPSec tunnel. We solved the problem by opting for a 50 user license.
-
PIX 501 and THE, 3DES, AES
For a version newly produced PIX 501,
(1) are DES, 3DES and AES activation keys all pre-installed?
(2) how I can find on which of them is pre-installed on my PIX 501?
(3) when I create a server VPN (on the PIX 501), I see that all three OF THEM, 3DES and AES are available in the drop-down list of the PDM configuration screen. Does that mean my PIX 501 have all three of them (FROM THE, 3DES and AES)? -If the answer is no, assume that only is preinstalled on PIX 501, then why/how can appear in the drop-down list the 3DES and AES?
Thank you for helping.
Scott
Should be integrated already. depends on the way the news is your PIX 501.
To be sure to log in to the console and type:
See the version
See the example output version:
See the pixfirewall version (config) #.
Cisco PIX Firewall Version 6.2 (3)
Cisco PIX Device Manager Version 2.0 (1)
Updated Thursday April 17 02 21:18 by Manu
pixdoc515 up to 9 days 3 hours
Material: PIX - 515, 64 MB RAM, Pentium 200 MHz processor
I28F640J5 @ 0 x 300 Flash, 16 MB
BIOS Flash AT29C257 @ 0xfffd8000, 32 KB
0: ethernet0: the address is 0050.54ff.3772, irq 10
1: ethernet1: the address is 0050.54ff.3773, irq 7
2: ethernet2: the address is 00d0.b792.409d, irq 11
Features licensed:
Failover: enabled
VPN - A: enabled
VPN-3DES: enabled
Maximum Interfaces: 6
Cut - through Proxy: enabled
Guardians: enabled
URL filtering: enabled
Internal hosts: unlimited
Throughput: unlimited
Peer IKE: unlimited
Serial number: 480221353 (0x1c9f98a9)
Activation key running: 0x36df4255 0x246dc5fc 0x39d2ec4d 0x09f6288f
Modified configuration of enable_15 to 12:15:28.311 UTC Wednesday, may 1, 2002
pixfirewall (config) #.
Here, you should see if THE or 3DES, AES encryption is active or not. If you have just SOME so you can use the following link and get for free a new activation key that allows 3DES and AES.
https://Tools.Cisco.com/swift/licensing/JSP/formGenerator/Pix3DesMsgDisplay.jsp
sincerely
Patrick
-
How to configure the PPPoE on PIX 501?
Mailto: [email protected] / * /
According to the below URL Cisco TAC:
but I always failed. And my PIX 501 Configuration noted below:
pixfirewall # write terminal
Building configuration...
: Saved
:
6.3 (1) version PIX
interface ethernet0 10baset
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
enable password xxxx
passwd xxxx
pixfirewall hostname
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
names of
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside pppoe setroute
IP address inside 192.168.1.254 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route inside 10.0.0.0 255.0.0.0 192.168.1.1 1
Route inside 20.0.0.0 255.0.0.0 192.168.1.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Telnet timeout 5
SSH timeout 5
Console timeout 0
VPDN group pppoex request dialout pppoe
Cisco localname VPDN group pppoex
VPDN group ppp authentication pap pppoex
VPDN username xxxx password *.
Terminal width 80
Cryptochecksum:xxxx
: end
[OK]
See the pixfirewall version #.
Cisco PIX Firewall Version 6.3 (1)
Cisco PIX Device Manager Version 1.1 (2)
Updated Thursday 19 March 03 11:49 by Manu
pixfirewall until 58 mins 6 dry
Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU
Flash E28F640J3 @ 0 x 3000000, 8 MB
BIOS Flash E28F640J3 @ 0xfffd8000, 128KB
0: ethernet0: the address is 000b.fd58.886b, irq 9
1: ethernet1: the address is 000b.fd58.886c, irq 10
Features licensed:
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
Maximum Interfaces: 2
Cut - through Proxy: enabled
Guardians: enabled
URL filtering: enabled
Internal hosts: 50
Throughput: unlimited
you have all the debugging logs?
-
VPN PPTP and PPPOE CLIENT ON PIX 501
Hello
Can I create a PPTP VPN and a client connection on a PIX 501 with a client to my ISP PPPOE connection. The PPPOE ip is dynamic and the VPN will be a static IP address. They gave me a username and password for VPN and PPPOE. Him also gave me an ip address for the VPN server.
Should that happen, it's that the PPPOE should connect to the VPN to work.
I can only get the PPPOE, but I don't know how to do this with a PPTP VPN set.
Here is my config:
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password xxxxxxxx encrypted
passwd xxxxxxx encrypted
hostname neveroff
domain-name neveroff.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list incoming permit icmp any any echo-reply
access-list incoming permit icmp any any source-quench
access-list incoming permit icmp any any unreachable
access-list incoming permit icmp any any time-exceeded
pager lines 24
icmp permit any echo outside
icmp permit any unreachable outside
icmp permit any time-exceeded outside
icmp permit any source-quench outside
icmp permit any echo-reply outside
icmp permit any information-reply outside
icmp permit any mask-reply outside
icmp permit any timestamp-reply outside
mtu outside 1500
mtu inside 1500
ip address outside pppoe setroute
ip address inside 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 192.168.1.0 255.255.255.0 0 0
static (inside,outside) tcp interface smtp 192.168.1.201 smtp netmask 255.255.255.255 0 0
access-group incoming in interface outside
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 inside
ssh timeout 5
console timeout 0
vpdn group pppoex request dialout pppoe
vpdn group pppoex localname xxxxxxxxx
vpdn group pppoex ppp authentication chap
vpdn username xxxxxxxx password xxxxxxxx
dhcpd address 192.168.1.10-192.168.1.41 inside
dhcpd dns 192.168.1.1 168.210.2.2
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
dhcpd enable inside
username neveroff password TEnlGTQMwqamBzMn encrypted privilege 2
terminal width 80
Cryptochecksum:c5bfafa70f21ed55cc1b3df377e110bf
: end
Thank you
Etienne
Happy to help and please kindly mark the message as answered if you have not more than other questions. Thank you.
-
Apple TV (4th Gen) ~ try to use Siri and instead of answers, it scrolls the suggestions of things I could say.
What happens and how can I cope?
Have you actually enabled Siri in settings > general > Siri, or are you just using the Siri button on the remote control?
-
to the left of the URL are 3 balls, red, yellow, green, who go around in a circle. When I click it it says download assistance, what is it for and how can I learn more about them?
An add-on (extension) for download videos from Youtube-like on your hard drive
- See-> https://addons.mozilla.org/en-US/firefox/addon/video-downloadhelper/
- See-> http://www.downloadhelper.net/index.php
- See-> http://www.downloadhelper.net/documentation.php
If this answer solved your problem, please click 'Solved It' next to this response when connected to the forum.
Not related to your question, but...
You may need to update some plug-ins. Check your plug-ins and update if necessary:
- Plugin check-> http://www.mozilla.org/en-US/plugincheck/
- Adobe Shockwave for Director Netscape plug-in: install (or update) the Shockwave with Firefox plugin
- Adobe PDF plugin for Firefox and Netscape: Installation/update Adobe Reader in Firefox
- Shockwave Flash (Adobe Flash or Flash): updated Flash in Firefox
- Next generation Java plug-in for the Mozilla browser: install or update Java in Firefox
-
Suddenly, I can longer open my pictures folder. I tried to move a picture to the folder to see what is happening and received an error message saying I was not allowed to display the contents of the folder and if I move the picture here, I won't be able to see. I ran disk utility and found no permissions error.
How this could have happened and how can I fix this problem? I'm the only user. No one else has ever physical access to my computer. However, I sign up for Skyhub a few weeks ago and copied the contents of my Macbook it. Since then, a "Remote disk" icon on my hard drive. This would be part of the problem?
Select it, choose get the information on the file menu, open the section sharing and permissions and give you access.
(141083)
-
I returned my iPhone5 to factory default and gave it to my grand daughter as a Christmas gift.
- She wants to download games etc but the itunes store guard asking my ID and PW.
- How can she save herself?
- I received and Apple to say that someone had tried to reset my password by e-mail.
- It is probably her mother because she also asked me to tell him my PW and ID.
- I currently use my PW and ID on my new 1Phone6 and do not want to share this.
Can you please help.
Julie Bateman
She needs to log out of your Apple ID in the store and just connect with hers. Go to settings, iTunes and App Store and tap on the Apple ID, then select Disconnect.
-
Error loading c:windows\system32\sshnas.dll wants to say what and how do I clear this pop up?
Hello
Step 1: sshnas.dll is a component of spyware or malware. Online virus and malware scanner and check.
http://www.Microsoft.com/security/scanner/en-us/default.aspx
Step 2: You can also see the question in the clean boot state.
-
I want to add the music that I downloaded on the internet Director of windows but it says missing a codec? Whats that and how to fix it?
I want to add the music that I downloaded on the internet Director of windows but it says missing a codec? Whats that and how to fix it?
================================
What is the (extension) format of the music files?Several audio formats are apparently compatible with
Movie Maker, but the most reliable is WMA.Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.
-
I try to download it and the message says: your current system does not. How it go down?
How to reset Internet Explorer settings
http://support.Microsoft.com/kb/923737
I hope that reset Internet Explore setting solve this problem
Otherwise, transfer your question in forum Internet explore
http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/threads if this post can help solve your problem, please click the 'Mark as answer"If you find it useful, mark it as useful by clicking the 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
Maybe you are looking for
-
I don't see all the levels in the tabs of the privacy and security in the preferences.
-
Message violates guidelines send IPv6 on PTR 550 5.7.1 documents and authentication
I use OS X Server (El Capitan) as my personal mail server. Everything is set up correctly. Mail works fine for everything except google gmail. This has happened for 2-3 years... whenever I have send emails to users of Gmail, I get "reviewed mail retu
-
I've created a new Word document & tried to send it as an attachment, I just couldn't do
I created a new Word document. I went to the file and send to and clicked on Mail to the recipient with an attachment. It's as much as I could get. He went to a sign in the window that cannot be opened. I couldn't understand it. any body out ther
-
Passport blackBerry password protect specific applications?
I have my work by e-mail, personal messaging and standard test for messaging on the phone and they are all easily accessible via the Hub which is great, except that I'm nervous if I give my phone to someone they can accidentally meet or send messages
-
Is there a way to send notifications by Email alerts of the ASA - AIP IPS module? It's a bit overwhelming this thing looking for the first time. Not quite sure yet how to navigate the IPSME.