PIX 501 Switch hardware Issue
My PIX 501 switch stopped working or has failed. The PIX is 10 months old. This is the second time I've seen that happen. The first time I sent it fixed by repair out of warranty, but they couldn't fix it. They said it was a chip owner they could not get from Cisco.
In any case, the unit has power. I am able to connect through the console and the WAN via SSH port. It is fully operational with the exception of the portion of the switch of the device.
Has anyone seen this kind of problem before? I've never seen a switch or a hub spoil. It's the second PIX to go wrong in the same local area network installed. PCs and servers all continue networking function wise, so connected to another switch.
Is that what I can do about this problem?
Thank you
Vince
Vince,
It depends on what type contract you have. You can open a TAC case and they will let you know the track.
Let me know if you have any questions.
Please mark this topic as resolved, so that others can benefit from.
Kind regards
Tags: Cisco Security
Similar Questions
-
On PIX 501 6.3 intermittent Internet access (5)
Hello
I have a problem of access to the Internet from the local network behind a PIX 501. It worked for months, but suddenly, I discovered that Internet access is intermittent. Internet access works for about 10-15 minutes and then goes down. When I reboot the firewall or disable ARP Internet works again. I turn on debugging with 'debug arp' and I get an error message "arp-in: Dropping request outside the unsolicited nonadjacent ROUTEOUTSIDE 0002.cf69.50cf for 82.x.137.x 0000.0000.0000»
Any ideas on what could be the problem?
Thank you for your help.
Kind regards.
Hello, Couple of things to check.
You have ICMP permitted on the external interface of the PIX. If so, can ask you someone to ping from the internet to the external IP address.
When they ping, can you unplug the external interface and see if they receive a response in return.
If so, then there is a problem with the access provider. They could give your IP address to another person.
If this isn't the issue, then you open a TAC case and resolve this problem.
See you soon,.
Gilbert
The rate of this post, if that helps.
-
Newbie Pix 501 HTTP authentication timeout
two issues here:
1. users that connect to the Internet through the Pix 501 ask about every three minutes to enter their user name and password. There must be a setting to change this, my dealer said there is no.
2. users that connect to the Internet, the first time have their IE session. By clicking Stop and then refresh or House brings to the top of the page. Any ideas.
Thanks in advance for any ideas you may have
Jeff Charland
Jeff,
First rule is to never trust your seller on technical issues;). Your dealer is wrong. You can indeed change the moment where a user is re - you are prompted to enter their credentials. There are basically 2 parameters, you need to know about the pix regarding delays of authentication:
(1) the inactivity timer. It's just like that. It expires an authenticated session via the PIX to hit X amount of time without all the traffic. The default timer on the PIX for this setting is 0, which means that we are no period of inactivity by the user (by default) monitor.
(2) the absoltue timer. Again, is to noise. This timer starts as soon as the user is authenticated and works continuously. When the time is reached, the user is obliged to to re-authenticate when they try to start a new connection (for example, by clicking a link in a web page). The default setting for the absolute timer is 5 minutes.
We recommend that you do not keep an absolute clock set for security purposes, but for ease of access, you can change these settings. Something like that would not be a 'off the wall' setting:
timeout uauth 01:00 absolute uauth 0: idle from 10:00
These settings will force the user to to re-authenticate every hour (absolute) or every 10 minutes after the connection becomes inactive.
And finally, no idea about #2 above. It happens with all users. Anyone who has tried to Netscape to see if it is a question only IE?
Scott
-
Hey guys,.
The switch integrated on a PIX 501 will freely forward traffic between devices plugged into it, as long as they are on the same subnet? I assume that the answer is Yes. If so, is it possible to isolate one device other network traffic using the PIX only? I can t think in a certain way, but I'm not a guru PIX, so I figured that I d ask Mr. thanks a lot for any information that you may be able to provide.
Do you hear them VLAN private?
If so, then 'NO', it is not possible.
There is no options at all to things like private VLAN on a PIX 501.
Connect a Switch which suports as suppoorts this kind of features and a port of the switch to the pix.
sincerely
Patrick
-
I have a PIX 501 for my house. Whenever I touch or someone bumps my office that it restarts. It seems that there is a problem with the connector for the physical PIX. I have endured the pain for a while now, but I would possibly solve the problem. Everyone knows the same problem? There was an alert and/or "Recall" on this issue?
You need to replace it. There is a view of land on this issue
-
PIX 501 for Cisco 3640 VPN router
-Start ciscomoderator note - the following message has been changed to remove potentially sensitive information. Please refrain from publishing confidential information about the site to reduce the risk to the security of your network. -end of the note ciscomoderator-
Have a 501 PIX and Cisco 3640 router. The 3640 is configured for dynamic map for VPN. The PIX 501 is set to pointing to the 3640 router static map. I can establish a tunnel linking the PIX to the router and telnet to a machine AIX on the inside network to the router. When I try to print on the network of the PIX 501 inside it fails.
What Miss me? I added the configuration for the PIX and the router.
Here are the PIX config:
PIX Version 6.1 (1)
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
enable encrypted password xxxxxxxxxxxxxxxx
xxxxxxxxxxxxx encrypted passwd
pixfirewall hostname
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 1720
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol 2000 skinny
names of
pager lines 24
interface ethernet0 10baset
interface ethernet1 10full
Outside 1500 MTU
Within 1500 MTU
IP address outside dhcp setroute
IP address inside 192.168.1.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
No sysopt route dnat
Telnet timeout 5
SSH timeout 5
dhcpd address 192.168.1.2 - 192.168.1.33 inside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
dhcpd allow inside
Terminal width 80
Cryptochecksum:XXXXXXXXXXXXXXXXXXX
: end
Here is the router config
Router #sh runn
Building configuration...
Current configuration: 6500 bytes
!
version 12.2
no service button
tcp KeepAlive-component snap-in service
a tcp-KeepAlive-quick service
horodateurs service debug datetime localtime
Log service timestamps datetime localtime
no password encryption service
!
router host name
!
start the flash slot1:c3640 - ik9o3s - mz.122 - 16.bin system
queue logging limit 100
activate the password xxxxxxxxxxxxxxxxx
!
clock TimeZone Central - 6
clock summer-time recurring CENTRAL
IP subnet zero
no ip source route
!
!
no ip domain-lookup
!
no ip bootp Server
inspect the name smtp Internet IP
inspect the name Internet ftp IP
inspect the name Internet tftp IP
inspect the IP udp Internet name
inspect the tcp IP Internet name
inspect the name DMZ smtp IP
inspect the name ftp DMZ IP
inspect the name DMZ tftp IP
inspect the name DMZ udp IP
inspect the name DMZ tcp IP
audit of IP notify Journal
Max-events of po verification IP 100
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
crypto ISAKMP policy 20
BA 3des
preshared authentication
Group 2
ISAKMP crypto key address x.x.180.133 xxxxxxxxxxx
ISAKMP crypto keys xxxxxxxxxxx address 0.0.0.0 0.0.0.0
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac vpn test
Crypto ipsec transform-set esp-3des esp-sha-hmac PIXRMT
!
dynamic-map crypto dny - Sai 25
game of transformation-PIXRMT
match static address PIX1
!
!
static-card 10 map ipsec-isakmp crypto
the value of x.x.180.133 peer
the transform-set vpn-test value
match static address of Hunt
!
map ISCMAP 15-isakmp ipsec crypto dynamic dny - isc
!
call the rsvp-sync
!
!
!
controller T1 0/0
framing ESF
linecode b8zs
Slots 1-12 channels-group 0 64 speed
Description controller to the remote frame relay
!
controller T1 0/1
framing ESF
linecode b8zs
Timeslots 1-24 of channel-group 0 64 speed
Description controller for internet link SBIS
!
interface Serial0/0:0
Description CKT ID 14.HXGK.785129 Frame Relay to Remote Sites
bandwidth 768
no ip address
no ip redirection
no ip unreachable
no ip proxy-arp
encapsulation frame-relay
frame-relay lmi-type ansi
!
interface Serial0 / point to point 0:0.17
Description Frame Relay to xxxxxxxxxxx location
IP unnumbered Ethernet1/0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
No arp frame relay
dlci 17 frame relay interface
!
interface Serial0 / point to point 0:0.18
Description Frame Relay to xxxxxxxxxxx location
IP unnumbered Ethernet1/0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
No arp frame relay
dlci 18 frame relay interface
!
interface Serial0 / point to point 0:0.19
Description Frame Relay to xxxxxxxxxxx location
IP unnumbered Ethernet1/0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
No arp frame relay
dlci 19 frame relay interface
!
interface Serial0 / point to point 0:0.20
Description Frame Relay to xxxxxxxxxxxxx location
IP unnumbered Ethernet1/0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
No arp frame relay
dlci 20 frame relay interface
!
interface Serial0 / point to point 0:0.21
Description Frame Relay to xxxxxxxxxxxx
IP unnumbered Ethernet1/0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
No arp frame relay
dlci 21 frame relay interface
!
interface Serial0 / point to point 0:0.101
Description Frame Relay to xxxxxxxxxxx
IP unnumbered Ethernet1/0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
No arp frame relay
dlci 101 frame relay interface
!
interface Serial0/1:0
CKT ID 14.HCGS.785383 T1 to ITT description
bandwidth 1536
IP address x.x.76.14 255.255.255.252
no ip redirection
no ip unreachable
no ip proxy-arp
NAT outside IP
inspect the Internet IP on
no ip route cache
card crypto ISCMAP
!
interface Ethernet1/0
IP 10.1.1.1 255.255.0.0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
no ip route cache
no ip mroute-cache
Half duplex
!
interface Ethernet2/0
IP 10.100.1.1 255.255.0.0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
no ip route cache
no ip mroute-cache
Half duplex
!
router RIP
10.0.0.0 network
network 192.168.1.0
!
IP nat inside source list 112 interface Serial0/1: 0 overload
IP nat inside source static tcp 10.1.3.4 443 209.184.71.138 443 extensible
IP nat inside source static tcp 10.1.3.4 9869 209.184.71.138 9869 extensible
IP nat inside source 10.1.3.2 static 209.184.71.140
IP nat inside source static 10.1.3.6 209.184.71.139
IP nat inside source static 10.1.3.8 209.184.71.136
IP nat inside source static tcp 10.1.3.10 80 209.184.71.137 80 extensible
IP classless
IP route 0.0.0.0 0.0.0.0 x.x.76.13
IP route 10.2.0.0 255.255.0.0 Serial0 / 0:0.19
IP route 10.3.0.0 255.255.0.0 Serial0 / 0:0.18
IP route 10.4.0.0 255.255.0.0 Serial0 / 0:0.17
IP route 10.5.0.0 255.255.0.0 Serial0 / 0:0.20
IP route 10.6.0.0 255.255.0.0 Serial0 / 0:0.21
IP route 10.7.0.0 255.255.0.0 Serial0 / 0:0.101
no ip address of the http server
!
!
PIX1 static extended IP access list
IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255
IP access-list extended hunting-static
IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255
extended IP access vpn-static list
ip permit 192.168.1.0 0.0.0.255 10.1.0.0 0.0.255.255
IP 192.0.0.0 allow 0.255.255.255 10.1.0.0 0.0.255.255
access-list 1 refuse 10.0.0.0 0.255.255.255
access-list 1 permit one
access-list 12 refuse 10.1.3.2
access-list 12 allow 10.1.0.0 0.0.255.255
access-list 12 allow 10.2.0.0 0.0.255.255
access-list 12 allow 10.3.0.0 0.0.255.255
access-list 12 allow 10.4.0.0 0.0.255.255
access-list 12 allow 10.5.0.0 0.0.255.255
access-list 12 allow 10.6.0.0 0.0.255.255
access-list 12 allow 10.7.0.0 0.0.255.255
access-list 112 deny ip host 10.1.3.2 everything
access-list 112 refuse ip 10.1.0.0 0.0.255.255 192.168.1.0 0.0.0.255
access-list 112 allow ip 10.1.0.0 0.0.255.255 everything
access-list 112 allow ip 10.2.0.0 0.0.255.255 everything
access-list 112 allow ip 10.3.0.0 0.0.255.255 everything
access-list 112 allow ip 10.4.0.0 0.0.255.255 everything
access-list 112 allow ip 10.5.0.0 0.0.255.255 everything
access-list 112 allow ip 10.6.0.0 0.0.255.255 everything
access-list 112 allow ip 10.7.0.0 0.0.255.255 everything
access-list 120 allow ip host 10.100.1.10 10.1.3.7
not run cdp
!
Dial-peer cor custom
!
!
!
!
connection of the banner ^ CCC
******************************************************************
WARNING - Unauthorized USE strictly PROHIBITED!
******************************************************************
^ C
!
Line con 0
line to 0
password xxxxxxxxxxxx
local connection
Modem InOut
StopBits 1
FlowControl hardware
line vty 0 4
exec-timeout 15 0
password xxxxxxxxxxxxxx
opening of session
!
end
Router #.
Add the following to the PIX:
> permitted connection ipsec sysopt
This indicates the PIX around all ACLs for IPsec traffic. Now that your IPSec traffic is still subject to the standard rules of PIX, so launched inside the traffic is allowed to go in, but off-initiated traffic is not.
-
VPN site-to-site between two PIX 501 with Client VPN access
Site A and site B are connected with VPN Site to Site between two PIX 501.
Also, site A is configured for remote access VPN client. If a remote client connects to Site A, it can only get access to the LAN of Site A, it cannot access anything whatsoever behind PIX on Site B.
How is that possible for a VPN client connected to Site A to Site B?
Thank you very much.
Alex
Bad and worse news:
Bad: Not running the 7.0 series PIX cannot route traffic on the same interface, the traffic is recived. Version 7.0 solves this ipsec traffic.
Even worse: PIX 501 can not be upgraded to 7.0...
A couple of things to think about would be the upgrade to hardware that can run the new IOS or allowing a VPN R.A. on site B.
HTH Please assess whether this is the case.
Thank you
-
I try to get my PIX 501 to forward traffic on port 1412 with TCP and UDP to use Direct Connect, and the problem I have is I can connect to a DC hub, but cannot establish connections with users.
I added the following to the default configuration from the factory with a partial success:
outside access list permit tcp any host 192.168.100.20 eq 1412
access-list outside permit udp any host 192.168.100.20 eq 1412
public static tcp (indoor, outdoor) interface 1412 192.168.100.20 1412 netmask 255.255.255.255 0 0
public static tcp (indoor, outdoor) interface 1412 192.168.100.20 1412 netmask 255.255.255.255 0 0
In the debug log set to the access list I rule this type of errors:
Deny tcp src outside other.users.ip.addr/3099 dst within the my.public.ip.addr/1412 by access-group "access_outside_in".
TCP request discarded outside my.public.ip.addr/45961 other.users.ip.addr/2362
I'm quite lost as to why it does not work when I think it should. I tried several ways, opening of port ranges and no chance for a transfer of the port sucsessful.
You can change you, outside the ACL to the following:
outside access list permit tcp any host eq 1412
access-list outside permit udp any host eq 1412
outside access-group in external interface
Save again with: write mem and also issue: clear xlate
I would like to know if it works.
Jay
-
Help the PIX 501 - cannot access startup.html
I'm new to the network and has received a job to configure the PIX 501 firewall.
The fact is:
We use IP table rules as a firewall on a linux machine. My pc is connected to a switch. So I use the yellow network cable to connect the port of the Pix 501 0 to the port in the switch. Then I disconnect my pc of swich cable and plug into the port of the Pix 501 1.
My pc is to use a static ip address before. I try to change to automatically get an IP address, but it will not work. So I changed the setting and use the IP address originally. Pop up message network connection icon says that the local connection is enabled. But when I try to ping 192.168.1.1, request time-out. Also I can't acess the https://192.168.1.1/startup.html.
I have a look at Books Online cisco and shootings of disorder, but most of them talk about the configuration or more advance features. I'm still on the very basic level to try to connect to the firewall.
I hope someone can help me. All ideas and questions are welcome. Thank you.
Your IP address should be fine. You do not want to have the PIX connected to your local network, even if you have the Linux firewall as well as this will cause a conflict. Keep the PIX the LAN for now. Your DNS configuration will have no effect because the url you are trying to reach is based on the IP address and not the domain name if your PC has nothing to look for.
You have to check the cable that you use - if your PIX has only an 'inside' interface, then you must use a crossover cable. If he has four so it's built in switch for a straight cable will be fine. Is what PIX model?
After checking the cable - see if you can console in the firewall - use the blue cable that came with the PIX and set up a connection (hyper terminal) terminal with the help of 9600, 8, no 1. If you can console and then you can stick in a basic configuration you can get.
-
Blue, sometimes white horizontal line appears at the top of the iPHONE 6Plus. Sometimes, the size increases. The screen freezes. Restart does not help. Phone hardware issue/replace?
knittyfingers wrote:
Blue, sometimes white horizontal line appears at the top of the iPHONE 6Plus. Sometimes, the size increases. The screen freezes. Restart does not help. Phone hardware issue/replace?
Back up your device, schedule an appointment with the genius bar and bring it to the Apple store.
-
Connectivity random Cisco Pix 501
Hello. I'm having some trouble with my CISCO PIX 501 Setup.
A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.
My configuration is:
-----------
See the ACE - pix config (config) #.
: Saved
: Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
6.3 (3) version PIX
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate 8Ry34retyt7RR564 encrypted password
2fvbbfgdI.2KUOU encrypted passwd
hostname as pix
domain as.local
fixup protocol dns-length maximum 512
fixup protocol esp-ike
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list acl_out permit icmp any one
ip access list acl_out permit a whole
access-list acl_out permit tcp any one
Allow Access-list outside_access_in esp a whole
outside_access_in list access permit udp any eq isakmp everything
outside_access_in list of access permit udp any eq 1701 all
outside_access_in list of access permit udp any eq 4500 all
outside_access_in ip access list allow a whole
pager lines 24
Outside 1500 MTU
Within 1500 MTU
outside 10.10.10.2 IP address 255.255.255.0
IP address inside 192.168.100.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
history of PDM activate
ARP timeout 14400
Global 1 10.10.10.8 - 10.10.10.254 (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Access-group outside_access_in in interface outside
access to the interface inside group acl_out
Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.10.2 255.255.255.255 inside
http 192.168.10.101 255.255.255.255 inside
http 192.168.100.2 255.255.255.255 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
ISAKMP nat-traversal 20
Telnet timeout 5
SSH 192.168.10.101 255.255.255.255 inside
SSH timeout 60
Console timeout 0
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
Terminal width 80
Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
------------Do you have any advice? I don't get what's wrong with my setup.
My DC is 192.168.100.2 and the network mask is 255.255.255.0
The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).
I have about 50 + peers on the internal network.
Any help is apprecciate.
Hello
You have a license for 50 users +?
After the release of - Show version
RES
Paul
-
Hello.. I am beginner in this kind of things cisco...
I'm trying to set up multiple VPN on a Cisco PIX 501 firewall with routers Linksys BEFVP41...
Since not very familiar with the CLI, I use the PDM utility and it was very easy for the first... Unfortunately, I get this error when I try to add the second VPN using the VPN Wizard:
Outside_map map (ERR) crypto set peer 200.20.10.3
WARNING: This encryption card is incomplete
To remedy the situation even and a list of valid to add this encryption card
Hi garcia
for each vpn/peer, you need to a separate instance of crypto card, the card will have the same name, but different sequence... numbers one map encryption can be attributed to an interface, but you can have several instance of cards inside a main...
for configuration, you can go through the URL below... It has all the details on IPSEC config:
http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/config/ipsecint.htm
I hope this helps... all the best... the rate of responses if deemed useful...
REDA
-
Microsoft secondary authority w / Cisco router / PIX 501
I'm trying to get digital certificates to work on my 2621XM router. I have also
need to put in place on the three firewalls PIX 501 but who have not obtained until now still. I have
don't have no access to the CA root, but it could bring in line if I had to. I have
have a stand-alone Microsoft subordinate CA that I want to use to publish all
certificates.
Is it possible, as well with the router and the firewall? If so, what version
the IOS do I need? I installed the add-on CEP at HQ. I can't
It works and I'm starting to wonder if it is still possible. If this doesn't
work, how can I make it work? I have all the documents that Cisco has combed
on the subject and have gotten nowhere.
Any help would be greatly appreciated. Thank you.
Jennnette,
I sent this document, let me know how it goes or if you have any questions.
Kurtis Durrett
-
I would like to open a session of hacking and intrusion of the attacks through a PIX 501 with a connection to broadband in a Home Office Setup. I have the camera upwards and the race and I am currently Setup with the Kiwi Syslog Dameon. What would be my best approach Logging all relevant information with the load to the bottom of the unit? Any suggestions / tips would be appreciated.
Thank you
It is a common logging configuration that I use:
opening of session
timestamp of the record
logging trap information
host of logging inside x.x.x.x
No registration message 106015
No message logging 106007
No message logging 105003
No registration message 105004
No message recording 309002
No message logging 305012
No registration message 305011
No message logging 303002
No message logging 111008
No message logging 302015
No message recording 302014
No message logging 302013
No registration message 304001
No message logging 111005
No message logging 609002
No message recording 609001
No message logging 302016
I usually do not enable the logging buffer (never use connection console it will affect performance) because it's not the messages timestamp (it only timestamps in the syslog). But the PIX loaded down with the load, you and Kiwi you before the PIX don't.
Also turn on the IDs on the PIX.
It will be useful.
Steve
-
I have a PIX 501 with wired high-speed LAN headquarters inside and outside. Which would be a solid policy IDS to enable and what interfaces it must be applied to? There will be other measures necessary to enable IDS?
IDS on the PIX itself is very limited, it checks only 59 signatures listed here (http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_62/cmdref/gl.htm#xtocid9 under the section of signatures supported IDS). The signatures themselves are pretty basic.
If you do not want to activate this, then for the signatures of attacks I would fix for drop/alarm/reset action, which is the default anyway.
You will also need to set the logging to a syslog server and monitoring for any 4000nn messages in syslog, cause it event IDS.
Maybe you are looking for
-
Is - this iPad Pro WiFi + cell comes with an international warranty?
I intend to buy iPad Pro WiFi + cell model. Can someone confirm if apple provides international coverage for iPad? (Example: bought from the United States and called for the guarantee in India vice versa)
-
HP Elite Probook 2570p l: HELP... error 0xc000000f
Hello While I was with my laptop, it went off suddenly and would not start again. I got an error 0xc000000f and I was asked to insert the windows installation disc, and then restart the computer. I did this and tried to repair windows, but nothing h
-
XServe Intel 5400 2 * 3.0 GHz QUAD CORE
Hello I'm looking to get an XServe 2 * 3.0GHz Intel QUAD CORE 5400 for a project and have disks for 10.7.5 leave for my other server. Can I install it agin on the new machine and I'll be able to update what? version of Mac OS X? Thank you Martin
-
In general we really like our new Officejet, but we are very frustrated by the automatic startup procedure. Whenever it is turned on, it performs a self check and then clean the print heads. This is awkward for two reasons: 1) we want to print quic
-
Computer takes more than five minutes to restart and stop.
The PC stops down, I need to switch him off and takes 5 minutes to start with the black screen after the XP logo appears. What could be the problem? Val Original title: My XP Pro is not closed and it takes 5 minutes to start