PIX 501
I have a PIX 501 for my house. Whenever I touch or someone bumps my office that it restarts. It seems that there is a problem with the connector for the physical PIX. I have endured the pain for a while now, but I would possibly solve the problem. Everyone knows the same problem? There was an alert and/or "Recall" on this issue?
You need to replace it. There is a view of land on this issue
Tags: Cisco Security
Similar Questions
-
Connectivity random Cisco Pix 501
Hello. I'm having some trouble with my CISCO PIX 501 Setup.
A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.
My configuration is:
-----------
See the ACE - pix config (config) #.
: Saved
: Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
6.3 (3) version PIX
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate 8Ry34retyt7RR564 encrypted password
2fvbbfgdI.2KUOU encrypted passwd
hostname as pix
domain as.local
fixup protocol dns-length maximum 512
fixup protocol esp-ike
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list acl_out permit icmp any one
ip access list acl_out permit a whole
access-list acl_out permit tcp any one
Allow Access-list outside_access_in esp a whole
outside_access_in list access permit udp any eq isakmp everything
outside_access_in list of access permit udp any eq 1701 all
outside_access_in list of access permit udp any eq 4500 all
outside_access_in ip access list allow a whole
pager lines 24
Outside 1500 MTU
Within 1500 MTU
outside 10.10.10.2 IP address 255.255.255.0
IP address inside 192.168.100.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
history of PDM activate
ARP timeout 14400
Global 1 10.10.10.8 - 10.10.10.254 (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Access-group outside_access_in in interface outside
access to the interface inside group acl_out
Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.10.2 255.255.255.255 inside
http 192.168.10.101 255.255.255.255 inside
http 192.168.100.2 255.255.255.255 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
ISAKMP nat-traversal 20
Telnet timeout 5
SSH 192.168.10.101 255.255.255.255 inside
SSH timeout 60
Console timeout 0
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
Terminal width 80
Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
------------Do you have any advice? I don't get what's wrong with my setup.
My DC is 192.168.100.2 and the network mask is 255.255.255.0
The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).
I have about 50 + peers on the internal network.
Any help is apprecciate.
Hello
You have a license for 50 users +?
After the release of - Show version
RES
Paul
-
Hello.. I am beginner in this kind of things cisco...
I'm trying to set up multiple VPN on a Cisco PIX 501 firewall with routers Linksys BEFVP41...
Since not very familiar with the CLI, I use the PDM utility and it was very easy for the first... Unfortunately, I get this error when I try to add the second VPN using the VPN Wizard:
Outside_map map (ERR) crypto set peer 200.20.10.3
WARNING: This encryption card is incomplete
To remedy the situation even and a list of valid to add this encryption card
Hi garcia
for each vpn/peer, you need to a separate instance of crypto card, the card will have the same name, but different sequence... numbers one map encryption can be attributed to an interface, but you can have several instance of cards inside a main...
for configuration, you can go through the URL below... It has all the details on IPSEC config:
http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/config/ipsecint.htm
I hope this helps... all the best... the rate of responses if deemed useful...
REDA
-
Microsoft secondary authority w / Cisco router / PIX 501
I'm trying to get digital certificates to work on my 2621XM router. I have also
need to put in place on the three firewalls PIX 501 but who have not obtained until now still. I have
don't have no access to the CA root, but it could bring in line if I had to. I have
have a stand-alone Microsoft subordinate CA that I want to use to publish all
certificates.
Is it possible, as well with the router and the firewall? If so, what version
the IOS do I need? I installed the add-on CEP at HQ. I can't
It works and I'm starting to wonder if it is still possible. If this doesn't
work, how can I make it work? I have all the documents that Cisco has combed
on the subject and have gotten nowhere.
Any help would be greatly appreciated. Thank you.
Jennnette,
I sent this document, let me know how it goes or if you have any questions.
Kurtis Durrett
-
I would like to open a session of hacking and intrusion of the attacks through a PIX 501 with a connection to broadband in a Home Office Setup. I have the camera upwards and the race and I am currently Setup with the Kiwi Syslog Dameon. What would be my best approach Logging all relevant information with the load to the bottom of the unit? Any suggestions / tips would be appreciated.
Thank you
It is a common logging configuration that I use:
opening of session
timestamp of the record
logging trap information
host of logging inside x.x.x.x
No registration message 106015
No message logging 106007
No message logging 105003
No registration message 105004
No message recording 309002
No message logging 305012
No registration message 305011
No message logging 303002
No message logging 111008
No message logging 302015
No message recording 302014
No message logging 302013
No registration message 304001
No message logging 111005
No message logging 609002
No message recording 609001
No message logging 302016
I usually do not enable the logging buffer (never use connection console it will affect performance) because it's not the messages timestamp (it only timestamps in the syslog). But the PIX loaded down with the load, you and Kiwi you before the PIX don't.
Also turn on the IDs on the PIX.
It will be useful.
Steve
-
I have a PIX 501 with wired high-speed LAN headquarters inside and outside. Which would be a solid policy IDS to enable and what interfaces it must be applied to? There will be other measures necessary to enable IDS?
IDS on the PIX itself is very limited, it checks only 59 signatures listed here (http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_62/cmdref/gl.htm#xtocid9 under the section of signatures supported IDS). The signatures themselves are pretty basic.
If you do not want to activate this, then for the signatures of attacks I would fix for drop/alarm/reset action, which is the default anyway.
You will also need to set the logging to a syslog server and monitoring for any 4000nn messages in syslog, cause it event IDS.
-
PIX 501, 1 static IP, IP address dynamic 2. Mesh full possible?
I have 3 sites. All sites have PIX 501. Central site has a static IP, 2 remote sites a dynamic IP.
I have no problem with the connection to the central site by using their dynamic IP address in a remote star connection.
Is it possible for 2 remote sites communicate? There is data that must be transferred between remote sites. I read somewhere in cisco site web which its possible via mesh on request.
Does anyone have an example of configuration on a VPN Site to Site where the Central site has static IP and remote sites with a dynamic IP? Remote locations teaches a dynamic IP from remote sites to the central server.
Thank you.
With IOS as your hub and then the Yes rays, the rays can learn dynamically address other departments using the PNDH. This type of configuration is called Dynamic Multipoint VPN (DMVPN), you can read everything you need to know about this here:
http://www.Cisco.com/warp/public/105/DMVPN.html
Even with EzVPN (not DMVPN) the rays will not learn the address of other rays, all communication is always via the hub. Call another talks would work, but as I said, the packages will talk-star.
-
How to configure the PPPoE on PIX 501?
Mailto: [email protected] / * /
According to the below URL Cisco TAC:
but I always failed. And my PIX 501 Configuration noted below:
pixfirewall # write terminal
Building configuration...
: Saved
:
6.3 (1) version PIX
interface ethernet0 10baset
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
enable password xxxx
passwd xxxx
pixfirewall hostname
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
names of
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside pppoe setroute
IP address inside 192.168.1.254 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route inside 10.0.0.0 255.0.0.0 192.168.1.1 1
Route inside 20.0.0.0 255.0.0.0 192.168.1.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Telnet timeout 5
SSH timeout 5
Console timeout 0
VPDN group pppoex request dialout pppoe
Cisco localname VPDN group pppoex
VPDN group ppp authentication pap pppoex
VPDN username xxxx password *.
Terminal width 80
Cryptochecksum:xxxx
: end
[OK]
See the pixfirewall version #.
Cisco PIX Firewall Version 6.3 (1)
Cisco PIX Device Manager Version 1.1 (2)
Updated Thursday 19 March 03 11:49 by Manu
pixfirewall until 58 mins 6 dry
Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU
Flash E28F640J3 @ 0 x 3000000, 8 MB
BIOS Flash E28F640J3 @ 0xfffd8000, 128KB
0: ethernet0: the address is 000b.fd58.886b, irq 9
1: ethernet1: the address is 000b.fd58.886c, irq 10
Features licensed:
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
Maximum Interfaces: 2
Cut - through Proxy: enabled
Guardians: enabled
URL filtering: enabled
Internal hosts: 50
Throughput: unlimited
you have all the debugging logs?
-
I would like to access my PC location xyz. How can I open port 22 access to my pc. I use pix 501.
Can anyone provide commands to open the port so that I can access my pc.
Thank you
totally agree because only 3 commands are needed.
list of allowed inbound tcp access any eq 22
public static tcp (indoor, outdoor) interface 22 22 netmask 255.255.255.255 0 0
clear xlate
However, all of these commands are missing in the config you have posted.
-
PIX 501 does support proxy ARP?
Hello
I would like to know if it is possible to publish a proxy arp some public address on the external interface of a PIX 501.
What is the command I should use?
Thank you
Hello
proxy ARP is performed automatically when you use the 'static' command to bind the IPaddress private an internal server to a public IP address.
Kind regards
Tom
-
Help!
I'm trying to set up VPN on my PIX 501. I have no experience of the PIX and have no idea where to start!
Any help will be greatly appreciated.
Thank you
Bennie
access list allow accord a
where is the name of the access list that you applied the entrants to your external interface. You may also allow accord coming out, if you have a list of incoming configured access to your inside interface.
-
Cisco 3640 to the PIX 501 site 2 site VPN performance specifications.
I intend on creating a site-2-site VPN in Star configuration with a Cisco 3640 as the hub and PIX 501 at the remote sites. My question is around the plug that I read.
.
The specifications for a PIX-501-BUN-K9 tell PIX 501 3DES Bundle (chassis, SW, 10 users, 3DES).
.
A question is what really "10 users. Which is the limit of the number of concurrent sessions, I have on the VPN at a given time, or that it means something else?
.
I also read the specs say that the Maximum number of VPN tunnels that can support a PIX 501 is 5. Because I'm not going to make a tunnel between the PIX 501 at the remote site and the 3640 on the central site, I think I would be OK. Is that correct or is the max value talk the maximum number of concurrent sessions on the tunnel tunnels?
.
Thank you.
UDP traffic always creates a session in the PIX so that the return traffic will be allowed in. The UDP timeout is 2 minutes but IIRC. If you go around NAT with a statement of "nat 0" should not create an xlate I think.
The real time is hard to say really, probably around 2 minutes for a UDP-only user, you would probably make a few 'local sho' orders on the PIX to really see for sure however.
-
Hello
I work to connect a PIX 501 VPN for a 3rd party hub 3015. The hub requires all traffic to come from a single source IP address. This IP address is assigned to me as z.z.z.z. I have successfully built the VPN and tested by mapping staticly internal IP with the IP address assigned, but cannot get the orders right to do with PAT in order to have more than one computer on the subnet 10.x.x.0. This Pix is also a backup for internet routing and NAT work currently as well for this.
I can redirect traffic to my subnet to the remote subnet via the VPN, but I can't seem to get the right stuff PAT to the VPN using the assigned IP address. If anyone can give me some advice that would be great.
lines of current config interesting configuration with static mapping:
--------------------------------------------------------------------------
access-list 101 permit ip 10.0.0.0 255.255.255.0 y.y.y.0 255.255.255.0
access-list 102 permit ip y.y.y.0 255.255.255.0 z.z.z.z host
access-list 103 allow host ip y.y.y.0 255.255.255.0 z.z.z.z
IP address outside w.w.w.1 255.255.255.248
IP address inside 10.0.0.1 255.255.255.0
Global 1 interface (outside)
NAT (inside) - 0 102 access list
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
public static z.z.z.z (Interior, exterior) 10.x.x.50 netmask 255.255.255.255 0 0
Route outside 0.0.0.0 0.0.0.0 w.w.w.2 1
correspondence address card crypto mymap 10 103
mymap outside crypto map interface
ISAKMP allows outside
Thank you!
Dave
Dave,
(1) get rid of static electricity. Use more Global/NAT. The static method will create a permanent
translation for your guests inside and they will always be this way natted. Use
NAT of politics, on the contrary, as shown here:
not static (inside, outside) z.z.z.z 10.x.x.50 netmask 255.255.255.255 0 0
Global (outside) 2 z.z.z.z netmask 255.255.255.255
(Inside) NAT 2-list of access 101
(2) the statement, "nat (inside) access 0 2' list will prevent nat of your valuable traffic."
Delete this because you need to nat 2 nat/global card. (as a general rule, simply you
If you terminate VPN clients on your device and do not want inside the traffic which
is intended for the vpn clients to be natted on the external interface).
(3) with the instructions of Global/nat 2, all traffic destined for the remote network will be first
translated into z.z.z.z. Then your card crypto using the ACL 103 will encrypt all traffic which
sources of z.z.z.z for y.y.y.0 24. This translation wil happen only when traffic is destined for the vpn.
I hope this helps. I have this work on many tunnels as you describe.
Jamison
-
Unable to connect to PDM on PIX 501
just cannot understand this. I have a PIX 501 I used to connect very well. Now I can't get the PDM to come up inside, outside, nothing. I use the same (old) of JAVA 1.4 version I always used. I can Telnet etc... Very well. The HTTP server is enabled and have granted access from my IP address. Any help would be greatly appreciated. See my config below.
See the pixfirewall # running
: Saved
:
6.3 (5) PIX version
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate 8Ry2YjIyt7RRXU24 encrypted password
passwd encrypted XXXXXXXX
pixfirewall hostname
domain ciscopix.com
clock timezone IS - 5
clock to summer time EDT recurring
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 X 0
fixup protocol h323 ras X 18 - X 19
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
name admin_subnet X.X.X.X
inside_outbound_nat0_acl X.X.X.X 255.255.255.0 ip access list allow admin_
subnet 255.255.0.0
inside_outbound_nat0_acl X.X.X.X 255.255.255.0 ip access list allow X.X
. X.X 255.255.255.0
outside_cryptomap_20 X.X.X.X 255.255.255.0 ip access list permit admin_subn
and 255.255.0.0
outside_cryptomap_20 X.X.X.X 255.255.255.0 ip access list allow X.X.X
. X 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP outside X.X.X.X 255.255.255.128
inside X.X.X.X 255.255.255.0 IP address
alarm action IP verification of information
alarm action attack IP audit
PDM location admin_subnet 255.255.0.0 outside
location of PDM X.X.X.X 255.255.255.0 inside
PDM location x.x.x.x 255.255.255.255 outside
location of PDM X.X.X.X 255.255.255.0 outside
location of PDM X.X.X.X 255.255.255.255 outside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 X.X.X.X 1
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
LOCAL AAA authentication serial console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
http X.X.X.X 255.255.255.0 inside
http admin_subnet 255.255.0.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
outside_map 20 ipsec-isakmp crypto map
card crypto outside_map 20 match address outside_cryptomap_20
card crypto outside_map pfs set 20 group2
card crypto outside_map 20 game peers X.X.X.X
outside_map crypto 20 card value transform-set ESP-AES-256-SHA
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP key * address X.X.X.X 255.255.255.255 netmask No.-xauth non - co
Nfig-mode
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 aes-256 encryption
ISAKMP policy 20 chopping sha
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 8 X 00
Telnet X.X.X.X 255.255.255.0 outside
Telnet X.X.X.X 255.255.255.0 inside
Telnet admin_subnet 255.255.0.0 inside
Telnet timeout 30
ssh X.X.X.X 255.255.255.255 outside
X.X.X.X 255.255.255.0 inside SSH
SSH timeout 30
management-access inside
Console timeout 30
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3600
dhcpd ping_timeout 750
username password XXXXXX XXXXXXXXXXX encrypted privilege 15
Terminal width 80
Cryptochecksum:
: endHello Mark,
lol Nice to know that everything works fine now
Don't forget to mark it as answered and to classify the useful messages (if you don't know how to evaluate a message just to get to the bottom of each answer and mark 1 being a wrong answer, being a great answer 5 stars)
Kind regards
Julio
PD: Some kudos for you (because of the answer)
-
The import of the PIX 501 config to ASA 5505
Is there something special that must occur to import a PIX 501 (IOS Version 6.3) config to an ASA 5505 appliance or is it as simple as download the config?
Greg
No, this isn't unfortunately because your pix is running 6.4 and the ASA 5505 will run a minimum of code 7.x and there were quite a few changes. Note that many existing commands would work, but some will not. Attached is a link to a doc for improving pix ASA who speaks both a manual method and an assisted version of tool -.
http://www.Cisco.com/en/us/docs/security/ASA/migration/guide/pix2asa.html
Jon
-
L2l IPSec VPN 3000 and PIX 501
Hello
I have a remote site that has a broadband internet connection and uses a PIX 501. We wanted to connect them with our main office using our VPN 3000 via VPN site-to-site.
I followed the following documentation:
However the L2L session does not appear on the hub when I check the active sessions.
The network diagram, as well as the PIX config and the screenshots of the VPN configuration for the IPSec-L2L tunnel is attached.
Any help or advice are appreciated.
I just noticed that the PIX firewall, the phase 1 paramateres are not configured. You must configure the same PASE 1 and phase 2 settings on both ends of the tunnel.
For example, on CVPN 3000, you have configured settings Phase 1 as 3DES, pre-shared key etc... We have the same configuration on the PIX firewall too.
Here is an example of sample config
I hope this helps!
Maybe you are looking for
-
Can I import my toolbar Firefox IE11 ROBO FORM?
I would like to import my FORM ROBO of IE11 toolbar in Firefox. Is this possible?
-
We did the IE, Firefox, Chrome, Safari and Opera - research looking for a touch of common function which was unused to use to help our application context key - and settles on the F9 key.Is there a way to ensure that the key F9 key can be passed to t
-
Satellite U200-122: how to use Pivot on external monitor?
I have a Satellite U200-122, wishes to use the external monitor depending on pivbot.But I can't find where I can get the display to rotate, so that it will be displayed on the external monitor in portrait format and accept the resolution 1024 x 1280.
-
Y510P issue of parameters power (SLI GT 755 m)
The other day, I tried to play then on the battery and got terrible frame rates. I got the power settings on maximum Performance. Are there any other settings that I'm missing? Thank you -Phil
-
IP renewal failed when XP to Win 7 machine (cable LAN Thr.)
Trying to connect Windows XP machine to Windows 7 computer via typical LAN cable, the goal is to connect to the internet using Win 7 machine. This used to work perfectly more early but recently I get about WinXP "Limited or no connectivity" error aft