Port 80 and RVS4000

Similar Questions

• Help with the VLAN and RVS4000

  I am trying to Setup VLAN on a RVS4000 to share our Internet connection with another office but do not allow access to our network of the other network. We have a BEFSX41 connected to Internet and also connected to our other site via a virtual private network to another BEFSX41. Port 1 on the BEFSX41 connects to Port 1 on an EZXS88W switch.

  The other company has provided the RVS4000 and also provides a WRT54GS router. I want to connect 2 ports on the BEFSX41 to Port 1 on the RVS4000 and 2 ports on the RVS4000 to track 1 on the WRT54GS.

  Port 1 on the RVS4000 is member of the default VLAN1 and Port 2 will be a member of VLAN2.

  Our IP network is 192.168.20.0/24

  BEFSX41 is 192.168.20.1

  The DHCP service is disabled

  The RVS4000 has a static IP address of 192.168.20.254 and is configured as a router

  DHCP is also disabled

  The wireless network is as follows:

  IP network is 192.168.21.0/24

  The address IP of WRT54GS is 192.168.21.254 and is static and also configured as a router.

  I don't know how to actually Setup the VLAN from here and the instructions are not useful. My questions are:

  1 port 1 on the RVS4000 must be safe, with label or Untagged?

  2 If the interval routing disabled?

  3. If so, how do I route between the RVS4000 and WRIGHT so the two networks have access to the Internet, but not to other networks?

  The befsx41 should be one that is connected to the internet so that your final point so that the vpn tunnel work. The wan port on the wrt54g must be connected to the lan of the befsx41 port.

  If your server is located behind the befsx41, you should be able to port forwarding. If your server is located behind the wrt54g you may experience the problem with the redirect because you need to forward ports on both routers and according to me, there are some applications that do not work on double NAT.

  If you want to have access to the internet on both VLAN of the rvs4000, it should work as a router so its internet port must be connected to the port the befsx41 lan.

• I just bought a keybboard ultra thin logitech for iPad air. It has a port for a small cable, but no cable in the box. What is the port for, and what don't get me?

  I just bought a keybboard ultra thin logitech for iPad air. It has a port for a small cable, but no cable in the box. What is the port for, and what don't get me?

  Have you tried the Logitech support site?

• Airport Time Capsule 3 to port usb2 and usb3

  Is the usb to Time Capsule on the new Time Capsule 3 to port a port USB2 and USB3?

  A USB 2.0 port.

  (141391)

• How do the 5 server not listening on ports 80 and 443

  I want to configure an Apache Server on a Linux virtual machine (using the last VirtualBox) on my Mac running El Capitan 10.11.3.

  5.0.15 server is already running on the Mac (and I want to keep it, with the exception of web services). I have disabled the sharing in the web server user interface, but it was not enough, Apache listening ports 80 and 443, prohibiting VirtualBox to listen to them and transmits them to the Linux virtual machine.

  So I put comment out these lines in /Library/Server/Web/Config/Proxy/apache_serviceproxy.conf:

  #listen 80

  #listen 443

  8008 #listen

  #listen 8800

  8443 #listen

  8843 #listen

  After a restart, Apache seems not to listen to ports 80 and 443 more. However, VirtualBox does not become the listener. I tried this command in the Mac terminal:

  -i sudo lsof: 80

  and nothing has been returned, suggesting that something in OS X still prevents VirtualBox to listen to ports 80 and 443. If I try to convey some random host port of Mac to port 80 in the virtual machine, then I can my virtualized server access from Safari on the Mac host via the custom port said. But I would use the standard port 80.

  Any help really appreciated.

  Instead of commenting, assign a specific IP for the server listen instead of * (which means that all the IP addresses). This is only to the server on port 80 and 443 in this config file. I sometimes give an additional IP address to the Ether. Your Linux Machine can connect to the second IP address or the first initial assigned to your server depending on your configuration.

  Server is very aggressive in it's use ports, he leaves so all services to operate, even if you have the use of ports to other IP addresses.

  Leo

• HP DC7700: Serial Port PCI and simple Communication controllers pilots missing in HP DC7700 windows 7 (32 bit)

  PCI\VEN_8086 & DEV_2997 & SUBSYS_2801103C & REV_02
  PCI\VEN_8086 & DEV_2997 & SUBSYS_2801103C
  PCI\VEN_8086 & DEV_2997 & CC_070002
  PCI\VEN_8086 & DEV_2997 & CC_0700

  and

  PCI\VEN_8086 & DEV_2994 & SUBSYS_2801103C & REV_02
  PCI\VEN_8086 & DEV_2994 & SUBSYS_2801103C
  PCI\VEN_8086 & DEV_2994 & CC_078000
  PCI\VEN_8086 & DEV_2994 & CC_0780

  Experts in the House should please come to my rescue.

  I just upgraded my Hp DC7700. I was able to get all the drivers except for SERIAL PORT PCI and PCI SIMPLE COMMUNICATIONS CONTROLLER missing. above are the two missing pilots hardware ID

  Hello:

  There is no W7 drivers for these devices.  You must use the Vista drivers and if auto installation does not work, you will need to install the drivers manually by navigating to the folder of the driver that was created when you ran the file from the device in the Device Manager (browse my computer for driver software).

  This package contains the driver Intel Host Embedded Controller Interface (HECI) for access to Active Management Technology (AMT) initiative of the Intel Digital Office for rated desktop models and operating systems.

  FTP://ftp.HP.com/pub/SoftPaq/sp34501-35000/sp34743.exe

  This package contains the Intel (LMS) Local Management Service and Serial - over - LAN (SOL) support for the technology of Directors Active (AMT) under the Initiative of digital office Intel for the supported desktop models and
  operating systems.

  FTP://ftp.HP.com/pub/SoftPaq/sp34501-35000/sp34744.exe

• Portege R500: external monitor does not work with the Port Replicator Port 2 and DVI

  I have a Portege R500 running Vista with a slim Port Replicator II and digital monitor Viewsonic.
  I connected the monitor to the DVI port on the port replicator and got it to work OK.
  Press fn + F5 would switch between the computer screen and the external monitor.

  Then it stopped working, and I can't make it work at all. F5 recognizes just the laptop screen.

  If I connect an analog display, it is fine, and I can pass between the two screens without difficulty.

  The strangest thing is that, if I reboot when the Portege R500 is docked, the digital monitor begins by displaying the boot sequence, but then the signal is lost as soon as the screen stops the display of the progress (in low resolution) bar.

  I spent an hour on the phone to support Friday, and he made me nowhere.
  They finished by saying that he should never have worked! So what is the DVI port because then?

  Any ideas?

  David

  Connect your monitor directly to your laptop and see if it is recognized and you can go through FN + F5 between the two views.
  If it works, then connect with port replicator, and then try again.

  It's probably best if you reinstall display drivers. Maybe there are new too on the download page.

• Serial port PCI and PCI Simple Communications Controller

  Hello!

  My computer OS is Windows 8.1.

  I just shearch something and I found that... I don't have serial Port PCI and PCI Simple Communications Controller. (Unintalled)

  Serial port PCI-> VEN_8086 & DEV_29B7 & SUBSYS_2819103C & REV_02\3 & 21436425 & 0 & 1 b

  Controller PCI Simple Communications-> VEN_8086 & DEV_29B4 & SUBSYS_2819103C & REV_02\3 & 21436425 & 0 & 18

  Sorry for my English. But can anyone help me?, where I can download these files.

  Hello:

  Here are links to the drivers you need...

  Install PCI Simple controller Comms

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=3459243&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dvc_78668_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  Install PCI Serial Port:

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=3459243&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dvc_78665_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• To set up my drive Web told me to "make sure that Ports 2077 and 2078 are not protected by a firewall... How can I find this information and if a firewall, how do I change or correct 2077 and 2078.

  I'm trying to implement a web disk with Hostgator for my blogs and the problem seems to be on my end, not theirs.  If I have a firewall port problem which prevents me from using my drive so what other options can I?.  Also what are the Ports 2077 and 2078 on my firewall.  How can I fix the problem?  Should I switch the disk and just use my desktop computer?   I wanted to keep the Hostgator on the disk. Also, I have the same problem if I jump the disc.  My 'add a network' don't like what I'm doing!

  Your message isn't clear when you refer to "floppy disk".

  In general, a firewall is designed to avoid that other computers access to your computer - unless you want that to happen.  You can add an 'exception' to the firewall that allows the software installed on your computer to communicate through the firewall, or you can open 'holes' (aka port) in the firewall that remain open regardless of whether an application on your computer is actively using them.  The latter is obviously a bit more risky.

  How to configure these exceptions depends on which firewall you use.  If you have Windows XP service pack 3 and you are using Windows Firewall, see http://windows.microsoft.com/en-US/windows-vista/Open-a-port-in-Windows-Firewall (well that article is on Vista, it applies as well to the firewall of Windows XP sp3, except instead of step 2, just click the 'Exceptions' tab - and don't forget to uncheck the box in the "General" tab that says "don't allow exceptions").

• opening ports 2077 and 2078 to use web disk

  Hello, I can't see my web files with webdisk and I would like to know how to manually open ports 2077 and 2078. I already read an article on the Microsoft Web site, but form a certain point the indication does not match what I see on my screen. Thank you

  Which firewall do you use?  If the built-in Windows Firewall, open the Security Center in Control Panel and select the Windows Firewall applet.  Select the Exceptions tab, and then click Add Port.  Specify your port.  Use the button change the scope to restrict the port to the correct network or IP addresses is not wide open to the Internet (unless that's what you need). Brian Tillman [MVP-Outlook]
  ------------------------------
  If a response may help, please vote it as useful. If a response to the problem, please mark it as an answer.

• WRT320N - loss of internet connection after redirect port 80 and 443

  Hello

  I have a problem with my new WRT320N. When I activate the port forwarding on my local server (ports 80 and 443), after a while I completely lose internet connection on all my computers connected to the router (wifi and lan computers). The router itself can ping and trace any Internet site through diagnostics to Web administration. When I turn off and click on save changes button, my internet connection works immediately again. I have the latest firmware installed and I tried to reset the router several times and set it manually since the beginning.

  My previously detained WRP400 has been configured to redirect these exactly the same ports and everything worked perfectly. Could someone advise me where could be a mistake? Thank you.

  I solved it. There was a problem with the combination of the service 'DHCP Reservation"of the router and client DHCP of Ubuntu. I disabled "Booking DHCP" and set the IP settings manually in the Ubuntu computer and now it works perfectly

• Hung up on the bad test page port (LPT1) and tail blocks to HP C4200 w/USB connect... will not erase

  Hanging test page to the wrong port (LPT1) and tail blocks to HP C4200 w/USB connect... don't delete.__How cancel?  Pls help.  TKS Ron Moore
  

  Ideas page: hanging in wrongly Test prt (LPT1) and tail blocks to HP C4280 w/USB connect... will not erase.

  How to cancel?  Pls help.   TKS, Ron Moore

  Hi Ron,

  1. how many printers is connected to the computer?

  2. did you of recent changes on the computer?

  3. what happens when you try to change printer (LPT1) port

  Method 1

  See the link below and run them the fixit tool available, check if it helps.

  Problems printing and printing errors

  http://support.Microsoft.com/mats/printing_problems/en-us?EntryPoint=lightbox

  Method 2

  If the previous step fails, then I suggest that you restart the computer the print spooler service and check if it works.

  A print spooler is a system service that temporarily stores the disk printing hard or in memory until the printer is ready to print.

  To change or restart the print spooler service

  You must be logged on as administrator to perform these steps.

  (a) open administrative tools by clicking the Start button, click Control Panel, clicking system and Maintenance, and then clicking Administrative Tools.

  (b) double click Services. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  (c) right click on the print spooler service, and then click Properties.

  (d) under the tab general , next to Startup type, make sure thatAutomatic is selected.

  (e) if the service is not already running, under Service status, click pie Sand then clickOK. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error 0 x 80070035 "[name of the PC] is not configured to establish a connection on Port"File and Printer sharing (SMB)"on this computer".

  Original title: "home network".

  0 x 80070035 "[name of the PC] is not configured to establish a connection on Port"File and Printer sharing (SMB)"on this computer".

  That's what I get on my ThinkPad when I try to do the networking. I placed all the parameters correctly: all 3 of my computers are set the same. 2 workstations work perfectly. They can even see the laptop but not to open all files. The laptop can, open same network t itself file. But he can see the whole of the network (including a printer, is told by the way). I, ve gone through all parameters twice. I've even set the C drives to share via the menus of context on each computer. I have visited many forums with none even come close to this problem (they all will tell you how to set the network parameters or they get very technical and over my head).

  I tried with & without a firewall.

  No password.

  I use a wired network.

  Laptop & 1 desktop computer running vista - 1 desktop computer running xp.

  They have all the latest service packs ms & udates.

  Any help will be appreciated.

  These files can be opened by norton or lenovo network setting apps. The settings do not work only in the application of network of vista. Nor can I work norton or lenovo from other computers.

  PS how can I ensure these settings effect may just lan and do not extend to the internet?

  Thank you bb

  I tried new drivers & returned through sharing & permissions, according to Jack, but he was not good. At the level of experience of my computer I can miss something obvious, but I doubt it because I've been very careful in following the instructions. I am experencing other problems with this laptop as well and I'll just get all. I am planing to get back anyway, that's why I needed network. I wanted to Exchange files over the network to avoid having to ' wait & swap "usb drives. Thanks anyway. Thank you BB bb

• probably caused by the settings of the firewall on your computer. Check the settings for HTTP port (80), HTTPS port (443) and FTP.

  Change the title: internet connection.

  Unable to connect to the internet, suddenly, message that I can't connect to the internet using HTTP<>< or="" ftp.="" thios="" is="" probably="" caused="" by="" firewall="" settings="" on="" your="" computer.="" check="" settings="" for="" http="" port(80),="" https="" port(443)="" and="" ftp.="" funny="" i="" was="" just="" on="" the="" net="" not="" more="" than="" 10="" minutes="" prior="" to="" this.="" checked="" all="" conections-="" good.="" what's="" my="" next="">

  Try a system restore to a Date before the problem began:

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  See you soon.

  Mick Murphy - Microsoft partner

• Port security and DHCP

  Hi all.

  I have configured the port security in some ports, and I don't think it handles images as it should. the following settings are

  -max: adds the correct number of MAC

  -permanent safe mode

  -throw

  I connect the legitimate devices to determine the maximum number of MACs, the port must learn and then I connect a device with Mac unsafe. I can get an IP address from the DHCP server, but no traffic is being so forward. I think that no legitimate unit should not be able to get an IP address as port security ignores all frames with an unknown source Mac

  Hi Stelios,

  Your configuration seems to be fine. Mine was connected only with the safety of ports and addresses max I put at 1. I see only 1 MAC address sends bootp all other devices connect via the switch on this port send no bootp.

  You could also make the capture of packets using the capabilities mirror port switch and application of wireshark. Devices are perhaps using old known IP addresses...

  Kind regards

  Aleksandra