Port not DMM SMTP 25

Similar Questions

• Pix 501 problem, I can not receive smtp messages

  Currently, I can send messages but cannot receive the mail from the Internet, if I remove the Pix and connect directly to the Modem/router then I can SMTP on port 25 and SMTP mail works fine both in & out.

  All what we want this Pix to allow at present is:

  (a) access to Internet to all clients on the network internal

  (b) allow the customers to pop mail web e-mail accounts

  (c) we want to use Exchange & Outlook and accommodate our own email via the SMTP Protocol

  Please find attached two documents: -.

  1. a current edited config of my Pix 501 running

  2. a PowerPoint of my network diagram.

  I appreciate a lot of help.

  Vinny.

  I finally found the problem.

  On the ADSL router, you have configured the same 192.168.0.0/24 network you use behind the post office

  Server. This configuration will not work because it leads to a duplicate IP address range and you have routing

  problems.

  Change the configuration to another range of IP between the ADSL router and PIX firewall and everthing will be

  work.

  Note the address unique public IP that is configured, received is on the router Netgear ADSL uses all other interfaces

  public IP addresses.

  Recovery of the networks and the IPs:

  80.x.y.z/255.255.255.x = Netgear outside intellectual property

  192.168.2.0/255.255.255.0 = network between the internal Netgear and the PIX outside interface

  192.168.1.0/255.255.255.0 = network between the PIX inside and the external interface of the mail server

  192.168.0.0/255.255.255.0 = network between the internal interface of mail server and mail clients.

  Use 192.168.2.0 255.255.255.0 for this network, and then set it 192.168.2.1 for your ADSL router inside

  interface, use a static IP 192.168.2.2 255.255.255.0 on the PIX firewall outside interface.

  ADSL installation:

  You can choose on the Netgear between all public traffic of the 80.x.y.z IP to 192.168.2.2 transmission which is NAT or

  You can transfer to forward the http, pop3 and smtp, didn't really matter, it's just important that you NAT or PAT it

  for the PIX firewall.

  PIX installation example:

  All traffic received on the PIX outside interface for http, pop3 and smtp is then transmitted by 192.168.2.2 to mail

  the server 192.168.1.2 external IP address.

  outdoor IP 192.168.2.2 address 255.255.255.0

  IP address inside 192.168.1.1 255.255.255.0

  acl_out list access permit tcp any host 192.168.2.2 eq http

  acl_out list access permit tcp any host 192.168.2.2 pop eq

  acl_out list access permit tcp any host 192.168.2.2 eq smtp

  Access-group acl_out in interface outside

  static (inside, outside) tcp 192.168.2.2 80 192.168.1.2 80 netmask 255.255.255.255 0 0

  static (inside, outside) tcp 192.168.2.2 110 192.168.1.2 110 netmask 255.255.255.255 0 0

  static (inside, outside) tcp 192.168.2.2 25 192.168.1.2 25 netmask 255.255.255.255 0 0

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Route outside 0.0.0.0 0.0.0.0 192.168.2.1

  Installation of mail server:

  The mail server has a default route to the PIX firewall.

  Default gateway on the mail server = 192.168.1.1

  Do you have NAt or PAT on the mail server internal clients to the Internet in the direction of the PIX? If not, you need to add another road on the PIX, so know the PIX the 192.168.0.0/24 network is behind the e-mail server, as this unit is the routing for this network.

  Add a route on the PIX inside interface:

  Route inside 192.168.0.0 255.255.255.0 192.168.1.2

  E-mail clients:

  All mail clients have the internal IP address of mail as default gateway server.

  Default gateway = 192.168.0.3

  This configuration will work 100%

  Sorry if I you confused.

  sincerely

  Patrick

• USB ports not working do not. Pavilion dm4-3090se

  USB ports not working do not.

  Thanks for your reply.

  no ports were working, so I went into Device Manager, uninstalled them, re-started... and... iola!

  they were back!

  Thank you again for your answer...

  Louise

• Satellite P10-304: USB Ports not recognize anything

  I have a Satellite P10-304 and the USB ports not recognize anything that are attached to them. Device Manager tells me that they are enbaled and works correctly. What can be wrong with them or what can I do?

  Hello

  One of my friends has the same unit on the work and everything works perfectly. It uses the USB hub too and have many external devices connected to the unit.

  By the way: something like who can occur if the external device is not removed correctly use safely remove hardware option. If you try to connect any other device after that in most cases it is not recognized at all. In this case, you can restart the device or remove ports from the Device Manager and use the hardware detection to find them again.

  Good bye

• COM not showing ports not after XP re - install

  I just finished a complete re-installation of Windows XP and cannot connect to the internet (via broadband). Convenience store said to check my COM ports in Device Manager because they "appear to be disabled. But they are not listed in the Device Manager. Follow the instructions in this thread:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/ports-not-listed-in-Device-Manager/f5e1dabe-df1c-4262-A912-688c40f75ddd

  Results:

  Method 1 - Ports still do even with active hidden view. However, I have seen "serial.sys" (listed under non plug-and-play devices), with a yellow exclamation mark-after internet research, found a post suggesting to uninstall it and reboot. I did, but now it is gone for good and I don't know how to get it back.

  Method 2 - cannot find the drivers of the 'COM' on the Dell Web site, nor on their resource CD (not even sure, there such a thing as a 'COM' driver - that's what I'm looking for?)

  Method 3 - I went through all my BIOS settings and couldn't find something called "COM." the closest thing I found and the only thing that was weird was "SATA-2 - Port SATA does not exist" (the same is indicated for SATA-3). But there seems to be no way to change/fix it.

  Nothing happens to my Dell Diagnostic tool.

  Controller Ethernet PCI VEN_8086 & DEV_10C0 & SUBSYS_020D1028 & REV_02\3 & 2411E6FE & 0 & C8 the drivers for this device are not installed.

  http://www.PCIDatabase.com/ reveals that the Intel network device in your office, probably on the motherboard. The driver should be on your CD, but if not you can download it here...
  http://www.Dell.com/support/drivers/us/en/19/DriverDetails/product/Inspiron-530?driverId=719HJ&osCode=WW1&FILEID=2731097675

  Controller Bus SM PCI VEN_8086 & DEV_ & SUBSYS_020D1028 & REV_02\3 & 2411E6FE & 0 & FB the drivers for this device are not installed.

  It's not installed the chipset drivers. Again, these should be on the CD but if not bring here...

  http://www.Dell.com/support/drivers/us/en/19/DriverDetails/product/Inspiron-530?driverId=M6R7T&osCode=WW1&FILEID=2731098689

  I suspect that the first item above will give you a broadband connection, but something else you said might indicate otherwise. If please reply with the brand and model of the device that you call a "modem" for more assistance.

  When you installed these drivers check again msinfo32 and check device manager...

  • Click Start
  • Click on run
  • Type devmgmt.msc and press enter

  Is there anything that is listed in the other peripheral topic or anything with an exclamation point (!)?

  Tricky

• USB port not to pick up when it is connected

  USB PORT NOT TO PICK UP WHEN IT IS CONNECTED

  Himanshu salvation,

  ·         How long have you been faced with this problem?

  ·         Did you make any changes before the show?

  Refer to the following Microsoft Fix It solution and click run now , and follow the steps to solve the problem:

  Hardware devices do not work or are not detected in Windows:

  http://support.Microsoft.com/mats/hardware_device_problems/

  Hope this information helps.

• Windows 7, handspring visor says COM1 port not available to sync

  running windows 7, old handspring visor will not not sync... says COM1 port not available

  Reference: http://forums.palm.com/t5/Windows-HotSync/Windows-7-and-Vista-hotsync-instructions-here/m-p/251755

• Color LaserJet MFP M476nw: Could not resolve SMTP for the scanning functionality of e-mail

  Help, please!

  I tried for days to get the scan to E-mail feautre to work and continue to get an error "Cannot resolve the SMTP server". I tried to use both @gmail.com and addresses @hotmail.com as a result of indications on each single post, that I could find related to this topic on the forums of HP, making sure to try every possible combination of SMTP/SSL/Port according to the parameters indicated by each email provider (including this special setting "app not secure", that I need to activate it for Gmail) and NOTHING.

  I use the web server HPs to set up the configuration.

  I'm desperate and start a new post on the forums is my last resource before you put this printer to sleep.

  Thanks in advance for the help!

  Hello @jerefle

  Try to do the following

  Upgrade the operating system on the printer (Firmware)

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=6457978&lang=en&cc=us#Z7_3054ICK0K8UDA0AQC11TA930O2

  Select the operating system and to choose the option fimware run the application and send the upgrade

  Go to the printer and go the following changes after the upgrade

  Implement > network > network services > IPV6 > Off

  Implement > network > link speed > complete 100TX

  Now of course at this stage you want to try to use the function

  His chest that we review a few moments so the way tea set up was made, I thin

  (The following information as its dummy data has just develop my point)

  

  For gmail, you can test with port 465, as well

  For hotmail that you want to use smtp.live.com port 25 or 465

  After this quick settings review if it does not then you want to do this

  On this Web page with the ip address that you're on go to network > identification identification network, save your primary and secondary DNS information, and then change to primary to 8.8.8.8 and 8.8.4.4 secondary and test again

• Requiring authentication for SMTPS, but not for SMTP

  Hi all
  
  On a cluster hive, beehive.domain.com, we created 2 endpoints for each SMTP and IMAP, a safe and the other normal, like this, users can connect to two ports (25 + 465 and 143 + 993).
  
  Endpoint on the secure ports were created to allow direct access from the outside to redirect the only secure ports (465 (smtp) and 993 (imap) through the firewall to the cluster of the hive.) I don't massively secure and that there is an instance of hive DMZ for this effect, but that is for later.
  
  Question: Is is possible to require authentication to use only secure SMTP port and not the normal? The idea being, inside the LAN users port 25 to send all the emails that Beehive will relay all emails coming from domain.com, authentication is not required it would disrupt some applications that need to send email. However, we want to prevent Mr. spammer to send his stuff from external identity spoofing the this address is @domain.com
  
  Any suggestions? I read in another post that one idea is to create an additional for the SMTP Protocol Secure alone, VMS as it is possible to have the identification required at the level of the virtual machines. who is?
  
  
  
  Kind regards
  
  David

  Hi David,

  fix, create a new VMS recvssl endpoint:

  beectl add_configuration_object - type 'oracle.ocs.management.model.EmailService.SMTPProperties.VMSProperties '.

  CONFIG_OBJECT_ID = da9444a0-2e3e-45e7-b5f2-98945514c6de

  name the component modify_property beectl VMSName - value SmtpSslVMS da9444a0-2e3e-45e7-b5f2-98945514c6de

  append_value - name of the component _EmailService:SMTPProperties VMSPropertiesList value da9444a0-2e3e-45e7-b5f2-98945514c6de beectl

  There was a BUG in 1.4.X beekeeper. So I post you the command line procedure. After that configures "Require AUTH" for this endpoint. This you can configure beekeeper.

  See you soon,.
  Sven

• Zbook G3 HP: HP Zbook Thunderbolt 3 Dock USB ports not working not

  I have a HP Zbook Thunderbolt 3 dock on my HPZbook G3.  I've recently updated the BIOS and the firmware to the latest version to solve other problems 'dock '.  Am now at the latest for both.  The two monitors and ethernet on the work of lightning 3, but none of the USB ports are active.

  I am sure that the USB ports work, because they used to work before the update BIOS and firmware.  Keyboard, mouse, or USB memory on the dock work.

  I tried to go to the HP support and install the updates with the USB in it, but it didn't work.  I have a workaround - just connect the laptop directly, but I'd like to get my fully functioning dock.

  Device Manager does not display devices with questions.  I'll try to update, but I don't know which one to look at.

  

  Hey people,

  HP is dedicated to providing quality products to meet the needs of our customers. We listen to the customer feedback on our recent Thunderbolt Dock for use with the latest products ZBooks, and Elite Notebook. We continue to work with our customers to solve problems.

  Please find tips and updates to improve your use of the HP Thunderbolt docking station.

  1. The Thunderbolt dock uses the latest technology thunderbolt. To be fully functional, it takes the latest firmware, BIOS, and drivers to work properly. Please follow the step by step process as described below in "The process of updating your device".
  2. Here are links to the user, technical white paper guide helps and guides troubleshooting. Please, use them to help when you have problems after you have fully updated your device and platform by following the instructions above. Please note that you may copy and paste the links in your browser.
  3. If you still have any questions, please call HP support. We're here and eager to help succeed you using the HP docking station new Thunderbolt.

  Useful links

  User Guide: http://h20565.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=11122586 & docLocale = en_US & docId = emr_na-c05141189

  Technical white paper: http://www8.hp.com/h20195/v2/GetPDF.aspx/4AA6-5088EEW.pdf

  Help & troubleshooting the Dock: www.hp.com \support\thunderbolt3dock

  Process to update your device

  NOTE: Instructions below is found in the User Guide "Getting Started" to "Implementation of the dock" to "step 2: update your computer.

  Before connecting the dock to your computer, update the BIOS, software and drivers on your computer.

  NOTE: If you do not, the wharf may not work. For best performance, keep all software and drivers on your computer up to date. (See table 1)

  Update the BIOS and the software and drivers:

  1. Go to http://www.hp.com/support. Select the drivers and Get software, enter your model of computer (on the computer service tag) number, and then select search for my product.
  2. Click the link for your specific computer, select your operating system and then download the latest version

  BIOS, software and drivers as follows: Intel® Thunderbolt Firmware Update Utility, Intel's Thunderbolt

  Secure Connect Driver, graphics drivers, ASMedia eXtensible Host Controller Driver, Broadcom Ethernet

  Controller and driver Conexant USB driver.

  1. Install the latest version of the BIOS.
  2. Restart the computer.
  3. Install the last stroke of lightning Secure Connect driver Intel.
  4. Restart the computer.
  5. Install the latest Intel Thunderbolt Firmware Update Utility
  6. Restart the computer.
  7. Install any remaining updates in any order. Restart the computer after each update.

  Table 1

  For the products supported Thunderbolt Dock all HP
  Name of the component	Category on the Support Page on hp.com	Where to check (this applies to all laptops)
  BIOS	(BIOS)	BIOS F10 Setup to information system
  Intel's Thunderbolt course connect driver	(Pilot - controller)	Right click on tray icon Thunderbolt to settings for details.

  The Thunderbolt of Intel® firmware update utility

  (Firmware)

  Right click on tray icon Thunderbolt to settings for details. Note that the numbers on the left will not directly reflected. NVM Firmware Version: 16 PD Firmware Version: 1.07.03

  Intel Graphics Driver

  (Driver - graphics)

  Right click on the desktop to graphic properties (icon intel) Options & Information Center Support.

  NVIDIA graphics driver

  (- Graphics - Nvidia driver)

  Right-click on the desktop to NVIDIA control panel to information system at the bottom left.

  AMD graphics driver

  (Driver - graphics)

  Right-click on the desktop to graphic properties (top) to Information to software.

  ASMedia eXtensible Host Controller Driver

  (Driver - Chipset)

  Programs & features or the Device Manager to Universal Serial Bus Controllers (dock of needs to be connected).

  Of Broadcom Ethernet controller driver

  (Driver - network)

  The Device Manager to network adapters (dock of needs to be connected).

  Conexant Audio Driver USB

  (Audio - driver)

  The Manager of devices to sound, video and game controllers (dock of needs to be connected).

  BPPSQ-

  I work on behalf of HP

• HP 15-r248nf: hdmi port not recognized on HP laptop after windows 10 update

  Need help! My laptop HP HDMI port does not work, apparently, that the HDMI is not recognized after the last windows 10 updated.

  Hi Lyn11,

  Thank you very much for your quick response. Yes, there are ways to find the product # and the n ° of the device.

  • On the desktop, (first screen of windows with all programs closed) Please press this key combination to bring up the system information which will also give the product # of the unit. Please, note it and n ° of the series unit. Don't post not your n ° of set of information on HP forums. Press the fn key (function key) and press "ESC" on the keyboard at the same time to bring up this information.
  • You may also locate in the bios. Please turn the unit off.  Wait a few seconds and as soon as you put it towards the up keep pressing the "Esc" key immediately, gently several times.
  • It will bring up the start menu. Then press the F10 key to go into the bios. The bios will also give the serial number information and product.
  • A third way to locate the product # would be to power down the device. Unplug the charger and remove the battery.  Then use a flashlight to look inside the compartment to locate the product #.

  Please visit these links which may provide more useful information.

  Link1: http://h30434.www3.hp.com/t5/Notebook-Audio/AMD-HDMI-port-on-dv7-laptop-is-lost-after-Win10-free-trial/m-p/5813013#M78967

  Link2: http://h30434.www3.hp.com/t5/Notebook-Video-Display-and-Touch/Boot-Device-Not-Found-Error-When-using-HDMI-cable-only/m-p/5803624#M139030

  I hope this helps. I would like to know how this happens. I hope the problem is solved without hassle and the unit works very well. Please keep me in the loop.

  Just to say thank youPlease click the ' Thumbs Up 'button to give a Kudos to appreciate my efforts to help me. If it helps, Please mark this "accepted Solution" because it will help many other people with the same problem to get it resolved without hassle.

  Now carefully and have a wonderful week ahead.

• Satellite Pro L10-103 - USB ports not working not

  Hi, my Satellite Pro L10 - 103 USB Ports do not work. I tried different things and finally my Advisor rubbed my computer clean of all programs and operating system. After reloading of the set up disc and having lost my dear some programs I am no further forward. It still does not.

  Anyone know if this means that it is a mechanical problem with the computer? (I use Windows XP). Your help would be greatly appreciated.

  Hey Buddy,

  As wrote Akuma did you use the Toshiba Recovery disk or the Microsoft Windows disk?

  After installing XP, make sure that Service Pack 3 is installed. It contains important updates and can be downloaded on the official page of Toshiba.

  In addition, try to remove all the USB ports on the Device Manager, restart the computer. Ports will still be recognized and ready to use once.

• USB ports not working not not on Satellite Pro C650 - 18 d

  Hello
  I have a Satellite Pro C650 - 18 d on which USB ports are dead.
  So far, I've updated the chipset and BIOS - but they stay dead. It doesn't seem to be a power either. I have a USB key with LED and it does not light.

  Any ideas? It's under warranty and so unable to try something wild!

  Thanks for any help
  Jim

  Hi Jim

  I recommend you to reinstall the OS and test the feature with the factory settings. Please, test it with several different USB devices. If none of them works, you must contact the Toshiba service provider in your country and leave check s portable.

  Do you know how to find the addresses and phone numbers?

• Dynadock USB Ports not working not

  I have a Toshiba Dynadock (unfortunately I do not know the model number I can't). It is less than a year and has two USB ports in the front, with 2 Sockets (I guess that one of the earphones and a microphone), has 4 ports usb at the back and probably a DVI/HDMI port as well.

  The problem is that none of the USB ports work on it, you plug a USB device into one of the ports and Windows 7 does not detect something that is attached. It was working fine until recently, and then the printer started to play up by printing only a few lines in a document that you asked to print, and then after that nothing worked (I don't think that the printer is at the origin).

  When I reassembled the eject button on the dock, Windows recongonises ejection and hot flashes with the software Dynadock saying "Dynadock has been ejected" or similar.

  The computer is a Toshiba. I reinstalled the drivers, made a restore to a date when I heard he was working and have restarted the dock, but nothing worked so far. Any suggestion would be appreciated.

  Thank you

  Hello

  Try it please use this driver - http://www.displaylink.com/support/downloads.php

• H8-1455 Bureau has three audio ports not in the specification

  I have two RCA audio ports and what appears to be a S-video port on the back of my computer that do not appear in the specifications.  Does anyone know if these would be inputs or outputs?

  You have an inside tv tuner card:
  http://support.HP.com/us-en/document/c03517384
  
  and where they are announced as inputs.
  
  C.