Port Replicator Multi Media, sound crackling

Similar Questions

• Portege 3440CT: Question about media port replicator

  Hi, sorry for my English...

  I have a question:
  I'm looking for a multimedia for my laptop port replicator.

  Do not include the port replicator (PA3042E-1DST) I found a driver for cd/dvd...

  Can I install a standard cd or dvd slim in the multimedia duplicator?
  Or he needs a car?

  Thank you.

  Hello

  I think that you need this one: PA3042E-1DST Multi Media Replicator Port, but according to certain specifications, this port replicator can be used with different options. This means that you must PA3014E - 1DVD DVD Drive Kit or PA3015U-1CDD 24 x CD-ROM Drive Kit II.

  That s all I found.

• Advanced Port Replicator PA3474E-7-248 poor sound quality on Tecra A7-248

  Hello

  recently, I bought used Replicator Toshiba Advanced Port PA3474E-1PRP, working nice, but the only problem is audio - output when connecting the speakers to the port replicator - speakers of the laptop still works + there is a significant loss in sound quality.

  Everyone had the same problem, or maybe there's a sollution for this?
  THX in advance

  PS my laptop is Tecra A7-248

  Hello

  To me that sounds like this, out on the port replicator doesn t port works properly if connect you directly to the computer laptop, everything works correctly, or can you notice any problems?

  Have you tested other speakers?

  In this case I would recommend updating the sound card drivers and BIOS. The two you can download on the Toshiba site.
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

• No sound on the Port Replicator port II (Tecra S11 - 12M)

  Hello! Because today, I have no sound on my sound from the Port Replicator II (PA3680E-1PRP) plug to run my external speakers. Instead, the internal speakers are running. On the laptop itself, making works well, only the port replicator appears to be dead.

  It has worked well over 10 months now without any complaint. I've seen a few similar cases in forums but no answer that could help me. I didn't lie all the drivers again.

  I work with WIN7/64-bit Service Pack 1.

  Anyone know how to fix?

  Thank you, christophe

  Hello

  Recommend to check this thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=56460

  * Milo_Tweenie wrote: *.

  + Did not know that the audio 3.5 mm output jack is actually run by a USB hub in the duplicator. +
  + Concluded that the multimedia USB Audio Device was not installed driver for the audio port. Click the button to update the driver, it has found the driver automatically and now I have sound. +

• Tecra M11 - 11L: no sound through Express Port Replicator II

  Hello

  I hope someone can help me.

  I have a Tecra M11 11 L with Windows 7 32-bit and an Express Port Replicator II docking station.

  When I plug my external speakers into the 3.5 mm plug on the laptop side, they work very well and the internal Laptop speakers are correctly muted.
  When I have the laptop dock and connect the external speakers to the Jack on the dock, I hear no external speaker but I get the sound from the internal speakers (i.e. they are is more silent).

  I did some research and some Dell users report the same problem with their docking stations after the upgrade to Windows 7, which suggests that this could be a driver problem Windows 7, rather than a faulty docking station.

  Someone at - it ideas?

  Thank you very much.

  Hello

  I found just the package of Windows Vista for Toshiba Express Port Replicator II drivers
  http://Support1.toshiba-tro.de/Tedd-files2/0/drvpack-20071108133820.zip

  There is no software driver Win 7 for Toshiba Express Port Replicator II.
  But this does not mean that this could be a software problem
  It is also possible that audio jack does not work as it should
  It would be desirable to test the Express Port Replicator II under Vista or Win XP

• X 301 has no sound when connected to the port replicator

  Hello

  We have a x 301 with a port replicator 45 k model 2777-cto 1610.

  We first had the problem with the blue screen and not SA of lenovo or IBM might help. I found the solution here.

  No, I have a new problem. When the port replicator is connected, there is no sound on the computer? Once the port replicator is unplugged, the sound works well?

  Any ideas or advice will be appreciated.

  Eugene

  When you connect to the rep of the port, the audio should be routed to the audio port on the default port rep, not your system. There should be a setting via icon taskbar for rep port driver that returns the audio to make of her.

• Portege Z30-A-12N with Port Replicator Port Hi-Speed USB III problems

  Hi all

  I have a big problem with my new Portege Z30-A-12N and Hi-Speed Port Replicator III.

  I connected the power, DVI, LAN, mouse and keyboard to the Port Replicator.
  Power, DVI and LAN are okay, but none will be found if I connect something to the USB Ports 2.0 or 3.0.
  No mouse, no keyboard, and no USB key.

  When I start my Portege I must enter a password after you press the power button.
  These password, I could enter with the external keyboard, but in windows, no keyboard has been found.

  If I connect the keyboard and mouse to the USB Ports of the Portege instead of Port Replicator, the two has been found.

  I ran Windows 7 Enterprise on the Portege.
  BIOS version is 3.30

  Do you have a solution for me?

  Hello

  The HI-SPEED PORT REPLICATOR III PA5116E-1PRP supports 2 x USB 2.0 and 4 x USB 3.0 ports.
  You n t special need Win 7 drivers in order to be able to use the USB ports or other interfaces such as VGA, DVI, audio, etc.

  Sound problems, make sure that the audio device has been selected in the right panel-> sound-> playback tab

  By the way: Win 7 needs USB driver 3.0 which is preinstalled when the laptop was equipped with USB 3.0 ports. My knowledge if your mobile phone does not support USB 3.0, you will be able to use the port replicator USB 3.0 ports.

  Finally and above all devices must be connected before you start the computer. The decision supported and compatible specifications: Portégé R30 - A, Tecra Z40 - A, Tecra Z50 - A, Portégé Z30-A/Z30t-A, Tecra A50 - has

• No audio output speakers Z50 - A Port Replicator PA5116A - PRI or Tecra

  I just got a new Tecra Z50A Toshiba with a port replicator Port-PRI PA5116A, when I first put it in the doc, he began to load the drivers.
  But during this process, the connection to the local network of abandonment and an error came stating that only four of the eight drivers have been installed.

  Now, the problem I have is that no sound / music out laptop speakers when in the RFSO or replicators offline to the speakers.
  I checked the playback settings that seem to be corrected.
  No mute setting.

  Any suggestions?

  I just got a new Tecra Z50A Toshiba with a PA5116A-PRI port replicator, when I first put it in the doc, he began to load the drivers.
  But during this process, the connection to the local network of abandonment and an error came showing that only four of the eight drivers have been installed.

  Now, the problem I have is that no sound / music out laptop speakers when in the RFSO or replicators offline to the speakers.
  I checked the playback settings that seem to be corrected.

  No mute setting.

  Any suggestions?

  Hello

  you have tested an update of the audio driver and install displaylink?

• Portege M400: Display appears on the side to the Port Replicator

  Hi all

  M400 laptop when starting at the port replicator will display the screen on the side. I must then, open the laptop screen and set the display in normal mode. When I'm correct display turn the laptop off and back on the display appears again on the side... Turning on a laptop without port replicator, portable computers the display is correct. What is going on. How to set the default display when in normal port replicator?

  Thank you

  These sound like the laptop would turn to Tablet mode after connection to the raplicator port.
  I think it has a bad setting in the utility of rotation.
  You must enter this utility and check the PC mode and the Tablet PC settings.
  I think that the parameters must be defined on primary landscape

  In addition, I would recommend checking the Toshiba mobile extension tool that is placed in the control panel.
  There is a tab to display change. Here you can activate the service of display change

• Tecra M9 longer works with the Advanced Port Replicator III

  Hello

  I have the Advanced Port Replicator III Plus (PA3474E-1PRP), and it works very well with my M5 (M3 and M200). For example I connect my laptop through it to my monitor/mouse/keyboard/external DVD/hard drives, sound, webcam etc...

  Now, I'm to assess what should I buy as my next laptop and the M9 (PTM91E-03000MEN) seems good.

  Question: * the M9 will work with my plu III advanced port replicator? *

  Otherwise, * y at - it another docking station option that will allow me to connect a M5 and an M9 * please? (of course not at the same time).

  If there is no solution that allows a single docking station for the M5 and M9, then I might as well choose a laptop from another supplier... Main reason to stick to Toshiba all these years is the docking station compatibility that I move older models to the newest...

  All thoughts welcome...

  See you soon
  Daniel
  --

  Tecra M9 and Tecra M5 do not have the same docking connector.
  This means Tecra M5 is the APR III +, Tecra M9 has Express Port Replicator.
  You need the correct docker for each system.

  May it is a solution to be able to use the Toshiba Dynadock. It's USB based:
  http://www.dynadock.com

• Express Port Replicator II and Tecra A10 - 12Z - only the power and LAN

  Since my Toshiba T3600CT I received with docking station, I discovered that I have a docking station. In the meantime, I had a small Sony who had no docking station, for which I got one of the first USB docking station and since then I've seen always to get laptops with docking station.

  But this time something went really wrong, the Toshiba Express Port Replicator II PA3680E-2PRP provides only power and LAN. There is no power in the USB ports, so no serial port or the sound, and DVI and VGA are also disabled.

  All these ports work fine on the Tecra A10, but not on the docking station.

  Of course, it is nice to have the power and LAN, but not when I expected too much of everything.
  So I was wondering if anyone has had a similar problem, it is like upgrading the BIOS for me who have not installed all the necessary software, or is it a fuse or something I could fix myself or is it a faulty docking that shouldn't have left the factory?

  Hello

  What's your Tecra pre-installed with original recovery image?

  When the laptop is preinstalled with recovery image simply connect compatible laptop Toshiba docking station and all the devices connected to the docking station will be recognized correctly and all available ports should work fine.
  Is that a Port Replicator basically "replica" ports on the laptop.

  On this virtual path, we cannot say that this port is 100% OK. What can you say about it? you bought is used a?

• Portege 3480CT - DVD player in those Port Replicator errors

  I have a Toshiba Portege 3480CT with an external media Port Replicator.
  The MPR has a DVD player, but I can't get the laptop to recognize DVD.
  He can see and read CDs, but I get the following error when I try to watch a DVD.
  "ASPI for Windows is not available...
  Only 32 bits supported CD rom drive... »
  The MPR recognizes that the drive is there.
  Laptop is running Windows XP SP2
  Have the BIOS update update and installed all the drivers Toshiba known.
  Can anyone help? Thank you.

  Hello

  In my opinion you need driver ASPI Google everywhere. Maybe you will find the solution for your problem. You can start with this one http://www.ncf.carleton.ca/~aa571/aspi.htm

• Tecra A11 - USB is not loan Express Port Replicator II

  Hey people,

  I'm absolutely fed up with this, so I hope you can help me with this: Iam using a Tecra A11 with Express Port Replicator II. There are three problems:

  1 USB mouse and USB keyboard are not ready to use so that until that Windows7 is fully loaded (BIOS Mode)

  2. There are USB devices such as USB-HDD, TV Tuner, telephone mobile-station host connected to the port replicator. Laptop remains in the Boot Logo screen and does not start until I have disconnect all devices. So I have to disconnect it, restart it and anchor it again. quite annoying.

  3. using the 64 bit version of WIndows 7 and playback sound stops regularly for 2-3 seconds when I use the speaker plug from the docking station. Using the plug in the laptop itself - no problem.

  I am absolutely fed up with it. Anyone have any idea?

  Thank you!

  Hey Buddy,

  With regard to the problem of USB:
  You have enabled USB legacy support in the BIOS? As far as I know, there is always such an option in the BIOS and it must be allowed, if you want to use USB devices before Windows starts.

  And using his most recent drivers for your laptop? You can check it on the Web from Toshiba site if a newer version is available:
  http://EU.computers.Toshiba-Europe.com

• Tecra A8 and Adv Port Replicator III - no audio output from the port replicator

  I have a Tecra A8 anchored on an Advanced Port Replicator III. All ports (network, USB, video) with the exception of the AUDIO ports seem to work well. I can get sound from the headphone jack on the front of the A8, but nothing since the station docking ports. Is there a docking station driver or something I need to install to get the sound from the docking station not the laptop?

  Hello

  The Advanced Port Replicator III supports the line and line port left.
  As already suggested by user above; Check if you are using the command-line output port!

  Welcome them

• III Plus driver/Frimware Advanced Port Replicator

  Hello

  I'm having some trouble with my M300 Poretege on Advanced Port Replicator III Plus. Some Fn keys do not work, and I'm not able to get proper display on my external monitor.

  Question: are there drivers for the Port Replicator? I don't have a CD or other installation media.

  Thank you, Richard

  Hello Richard

  Give us details please! These FN keys work without portreplicator? Don t FN keys work correctly?

  Check if the graphics card supports display resolution you have to put on the external screen.