Port Trunk on Vmware EXSi 5?

Similar Questions

• LGS308 Port Trunking Switch Cisco 3650

  I have a Cisco 3650 switch I need to connect my Linksys LGS308 again. I have the port trunking install everything on the side of Cisco, however, I'm not very familiar with trunking on the side of Linksys. What should the configuration looks like on the side of Linksys? Currently, I installed port no. 1 port trunking, and all VLAN belong them to this port. Once I have save the configuration, I can access is no longer the switch. Any ideas?

  The series of LGS Linksys has the same methodology VLAN that Cisco switches series SG.

  Which means a Port marked as port VLAN Trunk will be no marked member (PVID) of a single VLAN and can have several VLAN Tag assigned.

  Example:

  Cisco 3650: Port 1 set as a VLAN Trunk; PVID = 1 and tag VLAN 2,3,4

  LGS308: Port 1 set as a VLAN Trunk; PVID = 1 and tag VLAN 2,3,4; Management VLAN = 1,

  The IP address of the subnet IP of VLAN1

• SLM2024 port trunking

  I have a few SLM2024s that I need to configure it with a few VIRTUAL local networks that allow communication between the VLAN specific.  I think I understand how to do this, with the exception of the connection to the router.  It is my understanding that I need to configure the port on the router as a Trunk port.  However, I can't understand how to do this in the SLM2024.  Not support port trunking?

  Edit: Or I'm completely wrong to think that I have to configure the port on the router as a trunk?  I can set up communication between the VLANS without trunking port?

  WebEx sounds good. Our number here is 866.606.1866. You will need to have two things, your Cisco.com (aka CCOID) login ID and serial number. You can ask for me directly if you wish.

  Kind regards

  Christopher

• Channel Port LACP with VMWare ESXi IP hash Message: % SW_MATM-4-MACFLAP_NOTIF: < MAC > host in the vlan 1 is flapping between port

  Hello

  Currently I have a VMWare ESXi host with 2 network including 6 cards (3 of each) ports are connected to a X 3750.  I configured LACP on the switch and the Port of vDS group road based on IP Hash (802.3ad), my looks of config as follows:-

  src-dst-ip port-channel load-balance

  Interface Port-channel15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  !

  interface GigabitEthernet1/0/15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/16

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/17

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/18

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/19

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/20

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  Currently I see many MAC beat in the log of the switch.  From my understanding, I expect the MAC address out all ports, because that's what'd ESXi when you use 'route based on the hash of the IP.  I'm worried about the impact this might have on the CPU / switch.

  August 6, 09:42:05.700 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  August 6, 09:42:16.479 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.28e4 to host in the vlan 1 is flapping between port gi1/0/20 and 0/article gi1/17

  August 6, 09:42:18.719 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.7f6a to host in the vlan 1 is flapping between port gi1/0/19 and article gi1/0/20

  August 6, 09:42:20.766 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  Is it by design, if so can I disable the message?  If this isn't the case, please can you advise where I can check/change the configuration?

  Thank you

  Peter

  It is really gud who... .you mentioned your solution here.

  Can you please mark this question as answered, thatâ so it can help the other guys.

  Concerning

  Please rate if this can help.

• Catch 22 - Port Trunk Configurations: how to combine identifiers VLAN native with DHCP (but allows traffic of VM)

  Catch 22 - Port Network Configurations: how to combine identifiers VLAN native with DHCP (but allow the virtual computer)

  I came across a Catch 22.  Maybe someone can restore the directly here.  I found a "witch hunt" for sure.

  It comes with the Ports of junction on the side of the switch of the ESX host network.

  Context:

  Ok. The Setup is a HP Blade C7000 enclosure.  I try to configure ports for switching to the blades.  ESX 3.5 U4 will be installed the BL460cs.  Installation is preferred method: revive unattended.  No problem with the syntax of Kick-Start,

  I am here, it's the side network.

  The problem:

  I find a major complication in that the switch ports must be configured for both traffic Service Console and VMkernel, more Virtual Machine since only two NICs by blade. Not best practices, but we have only two switches Cisco 3020 inside.  The two uplink physical NIC is paired in the same vSwitch.  (No iSCSI does fortunately).

  So the Catch 22 question is as follows:

  If the id VLAN native set up on the switch port, DHCP works of course and the VMware boot loader is able to grasp a binary / packets on the network (FTP Site) and install OK.  But after no installation, no communication with SC unless I set the VLAN id of the SC to '0 '.  The value "4" 0 does not communication, but "40" is the VLAN native.

  If id configuring VLAN native retired from the Switch port, DHCP will not work and host does not have IP address during the VMware boot process.  This is as expected as traffic without label is not assigned an eligible

  VLAN, so no comms.

  The Port of the Switch configuration:

  interface GigabitEthernet0/16

  SERVERNAME description

  switchport trunk encapsulation dot1q

  switchport trunk vlan native 40

  switchport trunk allowed vlan 40-254

  switchport mode trunk

  switchport nonegotiate

  Speed 1000

  No cdp enable

  spanning tree portfast trunk

  end

  Summary

  OK, let's summarize where things are and if possible please attach responses to their digital identity.

  (1) is there a way to delete the VLAN tagging altogether side ESX host? Not only the id '0 '. The problem is with clearly with the VLAN native defined as "40".  If "40" IDs specified on the Group of ports for the Service Console, no joy, no comms. If the id of '0' value, capable of ping gateway and communicate on the network.

  (2) what is the problem with the definition of VLAN native as "40" when the config for the switch port is set as VLAN native "40"?  Or if it was a problem?  Both parameters clearly do not work together.

  (3) a switch receiving a unmarked frame it will assign to the VLAN Trunk native. Ok. Trunking bases and why I need a VLAN specified on the port for DHCP native work.  But it seems that since the id VLAN is set manually even as VLAN native, closed communications and no traffic as possible.

  (4) executives made tag 802. 1 q VLAN native?  I think that it is not and this could well be the problem. Since the id VLAN "40" is not labeled, but try to score the side host vSwitch port group.

  Please let me know your thoughts, community and how in general, we are approaching 2 NIC ESX configurations.

  When trunking multiple VLANs, you either have a default VLAN is nothing is tagged, or you don't.  That's what the vlan native to you, it defines which VLAN would be used if no tag is visible on the packets traversing the network.  For servers, if you are marking, then everything has to tag, if you're not marking at the server level, then the port must be either an access port or a VLAN native or default must be set.  I also don't keep your service console the same network as your vm.  Keep this isolated for the security of the network.  If you isolate this VLAN, you can separate and use a single IP address for installation and one for post construction.

  Or, you can provide an IP address during the build.

  -KjB

  VMware vExpert

• IPS inline & port interface port trunk Switch

  Hello

  Is it possible to configure the IP addresses as the topology below? SW1 and SW2 SPI connection ports is in trunk mode. I would like to configure the IPS in inline mode pairing interface. (not the vlan pairing mode)

  SW1 - IPS - SW2

  Kind regards.

  Yes, this method is fully supported.

  If you want to control all the VLANS with a single virtual sensor, then assign the pair inline interface to the virtual sensor.

  If you want to monitor the VLANS with different virtual sensors, we support groups vlan on this pair of inline interface.

  Do not confuse "inline-pair of vlan" with the "groups of vlan inline on a pair of inline interface.

  The "pair of vlan inline" will pair 2 VLANS on the same interface. When a package arrives in the sensor it will be sent back the same interface with its header vlan has changed.

  The "groups of vlan" on a pair of inline interface don't change headers for VLANs.

  They are only used for virtual local networks, so that the Group of VLAN can then be assigned to a specific virtual sensor.

  You could then take a group of VLANs for your office network employees and assign them to vs0 and take a second group of VLAN for your DMZ and assign them to vs1.

  You can place a vlan unique within each vlan, or you can place several VLANs within each group vlan.

  But it only made sense to have 4 groups of vlan, because you have only 4 virtual sensors on most devices (a bit like the 4215 have 1 virutal sensor so you can make groups of vlan on the 4215).

  I also recommend that you change your virtual sensor and set the Inline TCP Session tracking mode on "Interface and Vlan. In this way the sensor will separately monitor connections on each vlan. This is necessary if a router can route traffic between several VLANs. Without this setting, the sensor will become confused if it sees the same connection of multiple VLANs.

• How to configure Intel X 520 Dual Port card on VMware

  Hello

  I'm Hyeonjin.

  I'm configuration use VMware5.5.

  I want to use Intel X 520 Dual Port SFP + 10 GB as LOM (onboard NIC 1 G TX),

  but is not show the card MMIC Port and NIC set VMware

  How to set up the problem?

  Server: UCS C220 M4

  CPU: 2.4GZ * 2, Mem: 32 GB, HARD disk: 300 GB * 6

  On board NIC * 2, Intel X 520 SFP + Dual Port 10 GB

  x520.PNG

  

  Those who appear to be 3rd party and are not optical Intel.  Even Cisco SR optics do not work with this card.

  http://www.Intel.com/content/www/us/en/Ethernet-products/optics-cables/Ethernet-SFP-optics-brief.html

  Above link: "Note: other brands of optical modules SFP + will not work with the Intel® Ethernet Server Adapter X 520 series.»

  I recommend you get the specific ones screaming in the technical guide, that those who have been tested and work. (Intel SFP nde2-SFP-1WLR or nde2-SFP-1WSR).

  Thank you

  Kirk...

• Port forwarding in vmware workstation 9 (how to transfer all traffic to a virtual machine)

  You are looking for here: Advanced Configuration of NAT

  I can see how to redirect ports via in a particular host vmware NAT service, but my question is how can I transfer ALL traffic to a host? I found no info on how to do that.

  Is there any way I can forward all traffic incoming on a virtual machine?

  The syntax is = : and as such it is singular in all references, so I don't know of a way around it.

• port used by vmware view

  I'm looking for what ports are used to connect between the login server and the virtual machines that have the agent view them.  Thank you

  See this article for information, http://kb.vmware.com/kb/1027217.

• Drive a VMware EXSi

  Hello, I would like to know if it is possible to remotely control a virtual server EXSi?

  I want to perform actions such as start/stop/resume and especially back to a snapshot.

  The idea is to integrate this action in a continuous integration environment. It is necessary to provide for a procedure to compile, test, build software. At the end I should restore the snapshot of the virtual server to its original state.

  Does anyone know if there is a MAVEN plugin for this job?

  Thanks in advance.

  Luiz Felipe Maximiano

  Software development

  PowerCLI is the way to go. Take a look @ http://communities.vmware.com/community/vmtn/vsphere/automationtools/powercli?view=overview

• Network of twinning with Port trunks to support the host ESX VShere 4 with several NIC for load balancing across a HP ProCurve 2810 - 24 G

  We are trying to increase production of our ESX host.

  ESX4 with 6 NIC connected to HP Procurve 2810 - 24G 2 ports; 4; 6; 8; 10 and 12.

  The

  grouping of parameters on ESX is rather easy to activate, however, we do not know

  How to configure the HP switch to support above connections.

  Pourrait

  someone please help with a few examples on how to seup the HP switch.

  Help will be greatly appreciated as we continue to lose tru RDP sessions

  disconnects.

  Best regards, Hendrik

  Disabling protocols spanning-tree on the Procurve ports connected to the ESX host is going to promote a recovery more rapid port. Similarly, running global spanning tree is not recommended if you mix some VLAN iSCSI and data in the same fabric (i.. e. you do not want a STP process to hang storage IO). Spanning tree on your switches, look PVST (or Procurve BPMH) to isolate the STP VLANs unique events.

  In regard to the load balancing is, by default (route based port ID) value algorithm requires less overhead on the ESX hosts.  You may not use LACP on the Provurve the lack of facilities LACP ESX. You must use "route based on the IP hash" sideways ESX and 'static trunks' on the side of Procurve. Unless you have specific reasons why your network need loads this configuration, I'd caution against it for the following reasons:

  (1) IP hash requires thorough inspection of packages by the ESX host, increasing CPU load as load package increases;

  (2) the static configuration puts switch physics rigid and critical ESX host port mapping. Similarly, groups of ports all will fail as the Procurve batteries for management only and won't be on switches 802.3ad circuits Group (i.e. all ports of a group of circuits must be linked to a single switch) - this isn't a limitation of the port ID routing;

  (3) K.I.S.S. love port ID mix of port ID, beacon probe and failover on the port assignments you will get segregation of the raw traffic without sacrificing redundancy - even through switches.

  I hope this helps!

  -Collin C. MacMillan

  SOLORI - Oriented Solution, LLC

  http://blog.Solori.NET

  If you find this information useful, please give points to "correct" or "useful".

• List of Ports TCP UDP VMware Converter 4.0.1 P2V DMZ servers?

  Can someone list all TCP/UDP ports required to run VMware converter through a firewall? This is so that we can P2V Windows DMZ servers specific to both ESX in our DMZ servers.

  How about you use this instead?

  VMware vCenter converter required ports

  http://KB.VMware.com/kb/1010056/

  Kind regards

  EvilOne

  VMware vExpert 2009

  NOTE: If your question or problem has been resolved, please mark this thread as answered and awarded points accordingly.

• WLC CISCO - VMWare and additional network ports

  Hello world

  Hardware wise, I managed a 8540 and a CISCO 5508 wireless lan controllers, so know around the GUI.

  With the release of the VMWare Cisco WLC, it is ideal for a development and test lab environment. However anyone who has used will know it out of the box it does support 2 network cards (one for service and the other for management / data).

  The question:

  How to add additional network ports? In VMWare, it's easy, but how do you get the CISCO config to recognize? I have searched the forums and other areas, but can't seem to find someone who did this.

  See you soon

  Christian

  Hello

  Yes you are right, you can use only 2 network cards on VmWLC. never tried adding other network cards.

  But what you want to do? Is to add a virtual interface on your WLC?

  If so, you can configure your VmWare interface as a trunk and then create all your WLC virtual interface by defining the id vlan. Which makes sense for you?

  Thank you

  PS: Please don't forget to rate and score as correct answer if this answered your question.

• trunk port creation!

  Hi all

  How to convert the physical interface Port Trunking 802. 1 q!

  I have VM Machines and I want to put on different VLANS.

  "the physical switch support trunking.

  Thank you

  For this option, you can see the example in the article knowledge base that I have provided. Simply configure the VLANS allowed according to your needs and add the tag VLAN appropriate to each of the groups of port.

  André

• VMware Fusion Version 2.0.5 (173382) Serial Port config.

  I do some tests with some of our products and I struck a death sentence.  I have a few products that I need virtulize however, the ONLY way to configure (after Virtualization) is on the serial port.

  VMware Server (windows) will allow you to log in from a virtual machine to another virtual machine throughout the series. for example using named pipes, I do the following, but I can't use Vmware server, I need to know if fusion can do.  Even with the manual files if possible editing.

  
  customer .\pipe\com_1
  Server .\pipe\com_1

  VM-Windows XP (Client) -series virtualProduct (Server) - VM-internal

  I found that parallels offers this, but some of my images of BONES are designed to use vmware lsi logic and the installation fails for other reasons.

  Anyone has any ideas on this?

  Using

  Serial0.present = 'TRUE '.
  Serial0.filetype = 'pipe '.
  Serial0.filename = "/ tmp/series.
  Serial0.noLock = 'TRUE '.
  Serial0.yieldOnMsrRead = 'TRUE '.
  Serial0.pipe.endpoint = 'customer '.
  Serial0.tryNoRxLoss = 'TRUE '.
  Serial0.AutoDetect = "false".

  one side and

  Serial0.present = 'TRUE '.
  Serial0.filetype = 'pipe '.
  Serial0.filename = "/ tmp/series.
  Serial0.noLock = 'TRUE '.
  Serial0.yieldOnMsrRead = 'TRUE '.
  Serial0.pipe.endpoint = 'server '.
  Serial0.tryNoRxLoss = 'TRUE '.
  Serial0.AutoDetect = "false".

  on the other hand should work. Or, use the type of endpoint 'server' with different filenames from both sides and run 'socat' to couple the pipes.