SLM2024 port trunking

Similar Questions

• LGS308 Port Trunking Switch Cisco 3650

  I have a Cisco 3650 switch I need to connect my Linksys LGS308 again. I have the port trunking install everything on the side of Cisco, however, I'm not very familiar with trunking on the side of Linksys. What should the configuration looks like on the side of Linksys? Currently, I installed port no. 1 port trunking, and all VLAN belong them to this port. Once I have save the configuration, I can access is no longer the switch. Any ideas?

  The series of LGS Linksys has the same methodology VLAN that Cisco switches series SG.

  Which means a Port marked as port VLAN Trunk will be no marked member (PVID) of a single VLAN and can have several VLAN Tag assigned.

  Example:

  Cisco 3650: Port 1 set as a VLAN Trunk; PVID = 1 and tag VLAN 2,3,4

  LGS308: Port 1 set as a VLAN Trunk; PVID = 1 and tag VLAN 2,3,4; Management VLAN = 1,

  The IP address of the subnet IP of VLAN1

• IPS inline & port interface port trunk Switch

  Hello

  Is it possible to configure the IP addresses as the topology below? SW1 and SW2 SPI connection ports is in trunk mode. I would like to configure the IPS in inline mode pairing interface. (not the vlan pairing mode)

  SW1 - IPS - SW2

  Kind regards.

  Yes, this method is fully supported.

  If you want to control all the VLANS with a single virtual sensor, then assign the pair inline interface to the virtual sensor.

  If you want to monitor the VLANS with different virtual sensors, we support groups vlan on this pair of inline interface.

  Do not confuse "inline-pair of vlan" with the "groups of vlan inline on a pair of inline interface.

  The "pair of vlan inline" will pair 2 VLANS on the same interface. When a package arrives in the sensor it will be sent back the same interface with its header vlan has changed.

  The "groups of vlan" on a pair of inline interface don't change headers for VLANs.

  They are only used for virtual local networks, so that the Group of VLAN can then be assigned to a specific virtual sensor.

  You could then take a group of VLANs for your office network employees and assign them to vs0 and take a second group of VLAN for your DMZ and assign them to vs1.

  You can place a vlan unique within each vlan, or you can place several VLANs within each group vlan.

  But it only made sense to have 4 groups of vlan, because you have only 4 virtual sensors on most devices (a bit like the 4215 have 1 virutal sensor so you can make groups of vlan on the 4215).

  I also recommend that you change your virtual sensor and set the Inline TCP Session tracking mode on "Interface and Vlan. In this way the sensor will separately monitor connections on each vlan. This is necessary if a router can route traffic between several VLANs. Without this setting, the sensor will become confused if it sees the same connection of multiple VLANs.

• Port Trunk on Vmware EXSi 5?

  Hello

  We have vShpere Essentials more here with EXSi 5. I want to trunk 4 times of the network ports for each host. Then on Vmware, we can choose what VLAN belongs to the Virtual Machine.

  I think I know how to configure the Cisco switch. Series 4 ports in a trunk and puts all 4 ports in a channel group. I don't know how to configure Vmware. Someone has links to blogs with guides step by step please?

  Thank you

  QantasA380 wrote:

  Thanks for your help. I'll test this tomorrow (if I have time). I guess it's just a trunk mode standard switchport - nothing special on the cisco switch otherwise?

  Thank you

  Yes, that's correct.

  It is recommended to configure the portfast too.

• Network of twinning with Port trunks to support the host ESX VShere 4 with several NIC for load balancing across a HP ProCurve 2810 - 24 G

  We are trying to increase production of our ESX host.

  ESX4 with 6 NIC connected to HP Procurve 2810 - 24G 2 ports; 4; 6; 8; 10 and 12.

  The

  grouping of parameters on ESX is rather easy to activate, however, we do not know

  How to configure the HP switch to support above connections.

  Pourrait

  someone please help with a few examples on how to seup the HP switch.

  Help will be greatly appreciated as we continue to lose tru RDP sessions

  disconnects.

  Best regards, Hendrik

  Disabling protocols spanning-tree on the Procurve ports connected to the ESX host is going to promote a recovery more rapid port. Similarly, running global spanning tree is not recommended if you mix some VLAN iSCSI and data in the same fabric (i.. e. you do not want a STP process to hang storage IO). Spanning tree on your switches, look PVST (or Procurve BPMH) to isolate the STP VLANs unique events.

  In regard to the load balancing is, by default (route based port ID) value algorithm requires less overhead on the ESX hosts.  You may not use LACP on the Provurve the lack of facilities LACP ESX. You must use "route based on the IP hash" sideways ESX and 'static trunks' on the side of Procurve. Unless you have specific reasons why your network need loads this configuration, I'd caution against it for the following reasons:

  (1) IP hash requires thorough inspection of packages by the ESX host, increasing CPU load as load package increases;

  (2) the static configuration puts switch physics rigid and critical ESX host port mapping. Similarly, groups of ports all will fail as the Procurve batteries for management only and won't be on switches 802.3ad circuits Group (i.e. all ports of a group of circuits must be linked to a single switch) - this isn't a limitation of the port ID routing;

  (3) K.I.S.S. love port ID mix of port ID, beacon probe and failover on the port assignments you will get segregation of the raw traffic without sacrificing redundancy - even through switches.

  I hope this helps!

  -Collin C. MacMillan

  SOLORI - Oriented Solution, LLC

  http://blog.Solori.NET

  If you find this information useful, please give points to "correct" or "useful".

• Catch 22 - Port Trunk Configurations: how to combine identifiers VLAN native with DHCP (but allows traffic of VM)

  Catch 22 - Port Network Configurations: how to combine identifiers VLAN native with DHCP (but allow the virtual computer)

  I came across a Catch 22.  Maybe someone can restore the directly here.  I found a "witch hunt" for sure.

  It comes with the Ports of junction on the side of the switch of the ESX host network.

  Context:

  Ok. The Setup is a HP Blade C7000 enclosure.  I try to configure ports for switching to the blades.  ESX 3.5 U4 will be installed the BL460cs.  Installation is preferred method: revive unattended.  No problem with the syntax of Kick-Start,

  I am here, it's the side network.

  The problem:

  I find a major complication in that the switch ports must be configured for both traffic Service Console and VMkernel, more Virtual Machine since only two NICs by blade. Not best practices, but we have only two switches Cisco 3020 inside.  The two uplink physical NIC is paired in the same vSwitch.  (No iSCSI does fortunately).

  So the Catch 22 question is as follows:

  If the id VLAN native set up on the switch port, DHCP works of course and the VMware boot loader is able to grasp a binary / packets on the network (FTP Site) and install OK.  But after no installation, no communication with SC unless I set the VLAN id of the SC to '0 '.  The value "4" 0 does not communication, but "40" is the VLAN native.

  If id configuring VLAN native retired from the Switch port, DHCP will not work and host does not have IP address during the VMware boot process.  This is as expected as traffic without label is not assigned an eligible

  VLAN, so no comms.

  The Port of the Switch configuration:

  interface GigabitEthernet0/16

  SERVERNAME description

  switchport trunk encapsulation dot1q

  switchport trunk vlan native 40

  switchport trunk allowed vlan 40-254

  switchport mode trunk

  switchport nonegotiate

  Speed 1000

  No cdp enable

  spanning tree portfast trunk

  end

  Summary

  OK, let's summarize where things are and if possible please attach responses to their digital identity.

  (1) is there a way to delete the VLAN tagging altogether side ESX host? Not only the id '0 '. The problem is with clearly with the VLAN native defined as "40".  If "40" IDs specified on the Group of ports for the Service Console, no joy, no comms. If the id of '0' value, capable of ping gateway and communicate on the network.

  (2) what is the problem with the definition of VLAN native as "40" when the config for the switch port is set as VLAN native "40"?  Or if it was a problem?  Both parameters clearly do not work together.

  (3) a switch receiving a unmarked frame it will assign to the VLAN Trunk native. Ok. Trunking bases and why I need a VLAN specified on the port for DHCP native work.  But it seems that since the id VLAN is set manually even as VLAN native, closed communications and no traffic as possible.

  (4) executives made tag 802. 1 q VLAN native?  I think that it is not and this could well be the problem. Since the id VLAN "40" is not labeled, but try to score the side host vSwitch port group.

  Please let me know your thoughts, community and how in general, we are approaching 2 NIC ESX configurations.

  When trunking multiple VLANs, you either have a default VLAN is nothing is tagged, or you don't.  That's what the vlan native to you, it defines which VLAN would be used if no tag is visible on the packets traversing the network.  For servers, if you are marking, then everything has to tag, if you're not marking at the server level, then the port must be either an access port or a VLAN native or default must be set.  I also don't keep your service console the same network as your vm.  Keep this isolated for the security of the network.  If you isolate this VLAN, you can separate and use a single IP address for installation and one for post construction.

  Or, you can provide an IP address during the build.

  -KjB

  VMware vExpert

• trunk port creation!

  Hi all

  How to convert the physical interface Port Trunking 802. 1 q!

  I have VM Machines and I want to put on different VLANS.

  "the physical switch support trunking.

  Thank you

  For this option, you can see the example in the article knowledge base that I have provided. Simply configure the VLANS allowed according to your needs and add the tag VLAN appropriate to each of the groups of port.

  André

• 6248P VOIP and issue of trunk

  Hello

  I am swapping on an old Linksys switch which has our phones to VLAN our phones and computers on the 6248P switch.

  I installed the 6248P for VLAN1 as PC and VLAN101 voice. Tagged 101 on the 40 port I test and left VLAN1 as not identified.

  I have enabled voice VLAN and assigned the VLAN ID to 101 then on port settings change mode VLAN general and assigned PVID to 101.

  47 port is port trunking and I put this as the trunk of port but the phone does not get an IP address from the Cisco 800.  I'm simply by changing the link to the Linksys to dell to test, but it doesn't work.

  Can you advise me on the parameters of the Trunk and if this is true about what I've done.

  I'm a newb on a network, but I hope it makes sense above

  On the phone, you will need to check and make sure that the LDDP-MED is enabled. Then on the VLAN, and together the VLAN ID on the phone for VLAN 101. Here is a link on how to obtain these settings.

  http://bit.LY/1MG4x2h

  Once those setting are updated the phone will announce the switch and should be on the voice VLAN. If the phone does not a recognition in return, he will then send executives marked for VLAN 101. Whether the end result will be that the phone is on VLAN 101.

  Let us know if it works.

  See you soon

• LAG, VLANS and Trunking Force10

  I'm with vSphere and I a vSwitch with several groups of ports configured, including 2 assigned to VLAN ID and a network of management with no Vlan ID.  This vSwitch will use physical NIC grouped to route this traffic to a physical Dell Force10 MXL switch.  My understanding of the standard networking, a trunk port must be configured and VLAN must be added to this as labeled trunk port, while the traffic that has no Vlan ID is left unidentified and by default is the vlan by default (usually Vlan 1).  The attached picture is the topology I and I need to make this work, but do not have a lot of experience with Force10 switches and so far, it looks very different.  In addition, if it is relevant, the external switch in the diagram is actually 2 Force10 switches separated stacked, and there are two connections to the other switch (currently a 6224 not managed) between the firewall and F10s, which is a separate issue - those must be configured as an OFFSET on the F10s and the 6224? One or the other?  Or?  If anyone can help with the configuration for this topology?  Please help me out here.  Thank you!

  

  Currently, the best method to get assistance and recommendations with Force10 equipment, is through the Force10 support group. They will be more quickly and accurately help you with this inquiry.

  www.force10networks.com/.../ContactSupportGen.aspx

  Watching a white Force10 pages looks like a trunk can be configured with these commands.

  Configure VLANs tagged for an Interface of Port Trunk

  #configurer MXL2 MXL2 vlan (conf) #interface 11

  MXL2 (conf-if-vl-11) #tagged tengigabitethernet 0/1

  MXL2 (conf-if-vl-11) #no shutdown

  MXL2 (conf-if-vl-11) #exit

  MXL2 (conf) #interface vlan 12

  MXL2 (conf-if-vl-12) #tagged tengigabitethernet 0/1

  MXL2 (conf-if-vl-12) #no shutdown

  MXL2 (conf-if-vl-12) #exit

  MXL2 (conf) #exit MXL2 #.

  en.Community.Dell.com/.../download.aspx

  Thank you.

• MDS configuration for port channel

  I tried to put in place the new download FC port channel to a pair of 9124 s MDS, but as I don't know enough on the side MDS, I can't the link to come. Are there references available anywhere say you blow by blow exactly how to set up the side MDS of the channel of the port? Or maybe an example of configuration work?

  Thank you

  I don't think it's possible to configure the fabric of interconnections, FC switch mode that only VAN is based on those. The only mode of switch that is taken in charge and possible to configure is the local network Ethernet switching mode.

  I have configured the week last on a pair of 9124 s MDS and needed to activate the F port trunking and channeling Protocol feature by using this command

  "feature fport-channel-trunk.

  After that, I had to run SAN Port Channeling. Here's a snipit of my configuration:

  npiv functionality
  fport-channel-trunk feature

  interface port-channel 11
  active channel mode
  rate switchport dedicated mode

  interface fc1/1
  port-license purchase
  Channel-Group 11
  no downtime

  interface fc1/2
  port-license purchase
  Channel-Group 11
  no downtime

• SG200 SG200 VLAN Trunk does not

  I have 2 switches SG200-8 and I'm trying to cross the two switches of trunking VLAN, I configured IG1 article on both switches as a port trunk with native VLAN1 and VLAN2 tag.  VLAN 1 and 2 exist on both switches.

  Traffic on VLAN 1 passes without problem, but traffic on VLAN2 does not at all.  I confirmed that changing the trunk to tagged VLAN1 and VLAN2 native allows traffic then on VLAN2 flow through the switch but not so traffic on VLAN1.

  I also tried this as a SHIFT and a general port with the same results, everyone knows about this problem?

  Hi Ultrique01,

  I thank very you much for all the tests. This isn't very common hardware problem, but we might need to consider specifically your switches.

  At this point I suggest you to contact our Small Business Support Center and open the ticket:

  http://www.Cisco.com/c/en/us/support/Web/TSD-Cisco-small-business-suppor...

  Kind regards

  Aleksandra

• change of access port blocking another port

  Hello

  This is my first post here. I recently branch for a laboratory at home switch a sg300-10. I enabled couche3 routing on it and have encountered a strange problem. The switch is the default gw on this network, and in front of the switch, it is a cable modem)

  IP route 0.0.0.0 0.0.0.0 192.168.0.7).

  This is my config:

  config-file-header

  switch5ed948

  v1.2.7.76 / R750_NIK_1_2_584_002

  CLI v1.0

  SSD of encrypted file indicator

  @

  SSD-control-start

  config of SSD

  control of password file unrestricted SSD

  no control of the integrity of the file ssd

  SSD-control-end cb0a3fdb1f3a1af4e4430033719968c0

  !

  database of VLAN

  VLAN 10

  output

  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___

  Add a voice vlan Yes-table 00036 b Cisco_phone___

  Add a voice vlan Yes-table 00096e Avaya___

  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___

  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone

  Add a voice vlan Yes-table 00d01e Pingtel_phone___

  VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075

  Add a voice vlan Yes-table 00e0bb 3Com_phone___

  IP address of 192.168.0.120 dhcp relay

  activate a dhcp IP Relay

  Info IP dhcp option

  No Hello activation

  hostname switch5ed948

  No complexity of passwords allow

  ID password cisco

  Server SNMP Server

  clock timezone "" 1

  summer time clock web recurring EU

  unicast SNTP client enable

  unicast SNTP client survey

  192.168.0.120 SNTP server

  The telnet server IP

  !

  interface vlan 1

  no ip address dhcp

  activate a dhcp IP Relay

  !

  interface vlan 10

  name of LOM

  IP address 192.168.10.254 255.255.255.0

  activate a dhcp IP Relay

  !

  interface gigabitethernet7

  switchport mode access

  !

  interface gigabitethernet8

  switchport mode access

  switchport access vlan 10

  !

  IP route 0.0.0.0 0.0.0.0 192.168.0.7

  Pretty simple. About gi7 gi8 I want to configure 2 interfaces (lights out management) of LOM 2 devices in vlan 10.

  When I enable the vlan 10 on gi7, I lose network connectivity to devices behind IG5 which is a trunk port vlan 1. Very strange

  So, I just want to use 2 ports such as access on a non-standard VLAN ports. These ports should not be ports trunk/general, simple access to the ports.

  What I'm doing wrong here?

  TIA,

  Natxo

  Natxo, that's how it takes work.

  interface vlan 1

  IP 192.168.0.254 255.255.255.0

  interface vlan 10

  IP address 192.168.10.254 255.255.255.0

  --------------------------

  Host A is located in a port which is a member of the vlan 1. A NIC host configuration should be--

  IP 192.168.0.x

  Mask 255.255.255.0

  Gateway 192.168.0.254

  Host B is located in a port which is a member of the vlan 10. B NIC host configuration should be--

  192.168.10.x intellectual property

  Mask 255.255.255.0

  Gateway 192.168.10.254

  ----------------------------

  Now, if the host A and B are both capable to respond to ICMP, while there should be no problem to ping any direction. Also, make sure that if either of these computers have access to turn off wireless.

  -Tom
  Please mark replied messages useful

• trunk VSAN 6248 uplink interface

  Hi all

  I'm new to the UCS platform,

  I want to master multiple VSANs in FI 6248 on the single interface / portchannel. to 5548 upstream switch. Since the location of different heterogeneous storage 2.

  Ask let me know opportunities, configurations or any recommendations are available for configuring it.

  Hello Christine,.

  You can enable port FC port trunking and create port channels for FI of UCSM CF (SAN tab > SAN clouod).

  On N5K, you must enable fport-channel-trunk feature and create CF port-channel.

  Padma

• Pass the trunk between catalyst and PIX

  Hello

  Yesterday I had very good response on the forum how to create the VLAN on PIX, I created the subinterfaces and VLAN which their responsibilities. I configured the IP addresses as well. Did the same on the switch of Cat - created SVI and assined their IP add back. Cat shows switch port trunking is correctly but I can't ping from PIX to the switch and vice versa. Help, please.

  RVR

  Is it possible for you to view the configuration of the PIX? At least the configuration of the interface?

  And configuration of the trunk on the switch interface?

  Concerning

  Farrukh

• Problem of BladeCenter ESX Server Vlan trunking

  VLAN for the ESX BladeCenter server problem

  ESX, Bladecenter, VLAN

  Hello

  The bladecenter was initially setup by a company and only allows me

  create a VM from Vlan 2. The problem is that I'm out of intellectual property that

  VLAN and I wanted the ability to use another address space for the

  VM I have already created a new vlan 20.

  This is the current configuration of the switch.  Everything I have added to these configurations to before was sw trunk allowed vlan add 20

  Switch CISCO 4500

  Interface Port - Channel 1

  switchport

  switchport trunk encapsulation dot1q

  switchport vlan trunk native 3

  switchport trunk allowed vlan 3: 1-20

  !

  !

  interface GigabitEthernet5/39

  Description Port Trunk BLADECENTER-sw2-p17

  switchport trunk encapsulation dot1q

  switchport vlan trunk native 3

  switchport trunk allowed vlan 3: 1-20

  channel-group mode 1 on

  !

  interface GigabitEthernet6/2

  Truck BLADECENTER-sw2-p17 Port Description

  switchport trunk encapsulation dot1q

  switchport vlan trunk native 3

  switchport trunk allowed vlan 3: 1-20

  channel-group mode 1 on

  !

  Config - sw1 Bladecenter switch

  VLAN 2

  Server

  VLAN 3

  WAN

  VLAN 20

  Server2

  Interface Port - Channel 1

  switchport vlan trunk native 3

  switchport trunk allowed vlan 3: 1-20

  interface GigabitEthernet0/17

  switchport vlan trunk native 3

  switchport trunk allowed vlan 3: 1-20

  Cisco-switch macro description

  channel-group mode 1 on

  !

  interface GigabitEthernet0/18

  switchport vlan trunk native 3

  switchport trunk allowed vlan 3: 1-20

  Cisco-switch macro description

  channel-group mode 1 on

  Blade switchport where the host is contained

  interface GigabitEthernet0/9

  Description blade9

  switchport vlan trunk native 2

  switchport trunk allowed vlan 2.20

  switchport mode trunk.

  The host ESX IP is in Vlan 2

  End result is that I can't use any VLANS in this new range.  There is no Vlan ID or installation marking.

  Thanks in advance.

  Grand...

  Don't forget to assign points for correct or helpful answers