PowerConnect m6220 cable console

Similar Questions

• reset the password on a Dell PowerConnect M6220

  Hello, I'm trying to reset the password on a Dell PowerConnect M6220.  Can connect to the CMC via the https Web page, I don't see how to do it from there.

  Then I'll try to plug a USB serial cable into the console port and reset the password via a console session using teraterm but when I do that all I get is a white screen.

  Parameters of the series are:

  Cable: The Null Modem

  Bits per second: 115200

  Data bits: 8

  Parity: None

  Stop bits: 1

  Flow control: no

  Any ideas on how I can access telnet access to the device to reset the DDT successfully

  Thank you

  Kevin

  You can connect to the console port internal to the switch via the CLI of CMC

  Telnet to the CMC, then connect switch-a1 (a2 or b1 etc. etc.)

  This will give you the > invites, so either delet the startupconfig and recharge it, or put into you own username and password - remember that you can set on the schema of the interface of the band or band in slecting the appropriate interface

• PowerConnect M6220 ACL issues

  Hi, received a pair of blade switches PowerConnect M6220, pretty much the same as 6224

  I try to apply ACLs in interface, and I'm unable to do so.
  Here's what I'm trying to do:

  coresw (config) #access - internet-out list deny ip any 10.0.0.0 255.0.0.0
  coresw (config) #access - list on the internet permit each

  coresw (config-if-article gi1/0/17) #ip group-access internet-output

  Error when processing the ACL.

  coresw(Config-if-Gi1/0/17) #.

  <190>MAR 25 00:37:12 10.128.101.1 - 1 DRIVER [126512544]: broad_acl.c (1611) 4% ACL not applied to 134217728 port

  In this switch or on any interface on the switch, there is no other ACL.
  As you can see, it is a LCD 2 lines in the 90s, who refuses to work. Basically, what I'm trying to do is filter all local ip traffic.
  I'm doing something wrong here? According to www.dell.com/.../pwcnt_IP_ACLs.pdf , I can filter output destination.

  Any help is appreciated, thanks.

  I was able to test this on a M6220 and I can confirm the behavior you're seeing is a hardware limitation. IP based ACL cannot be applied evacuation. You should have no problem in applying the penetration.

• PowerConnect M6220 problem without tag switch of VLAN

  Good afternoon.
  I do not have much knowledge of networks and need help.
  M6220 have this connected to a HP ProCurve switch switch connected by a trunk.
  My problem is that I can not pass the 10 untagged procurve VLAN to the M6220 switch, can you help me?
  M6220 has firmware version 1.
  Thank you

  On a network connection VLAN native is the VLAN used to send and receive packets not marked. Here is an example of the configuration.

  Console (config-if-article gi1/0/1) #interface item in gi1/0/24
  trunk mode console (config-if-article gi1/0/24) #switchport
  Console (config-if-article gi1/0/24) #switchport trunk vlan 10 native
  trunk allowed vlan #switchport console (config-if-article gi1/0/24) add 10,11,12,13

  If trunk mode does not work, you can also try to use the general mode.

  Console (config-if-article gi1/0/1) #interface item in gi1/0/24
  mode console (config-if-article gi1/0/24) general #switchport
  Console (config-if-article gi1/0/24) #switchport general pvid 10
  Console (config-if-article gi1/0/24) #switchport general allowed vlan add 10 untagged
  Console (config-if-article gi1/0/24) #switchport general allowed vlan add 11,12,13 tag

  Hope this helps

• E20 cable console does not

  I recently created a console cable to connect in series to an E20 by the document

  https://supportforums.Cisco.com/docs/doc-24305, however it does not advice?

  The RJ45 pinout for cable I use is:

  

  The adapter series (by the above document):

  

  The connections that I use is based on the pinout RJ45 and document:

  GND - Brown

  RX - brown stripe

  TX - orange

  VCC - orange band

  All I get trying to connect to TeraTerm is a blank window.  How long should it take for the connection, or is there something on the E20 that needs to be done?  I've disconnected handset RJ45 jack and plugged the cable to the console instead.

  

  Thanks, Patrick

  Hello

  Have you tried to restart the E20?  Probably taste as follows:

  GND - orange band

  RX - orange

  TX - Brown band

  VCC - Brown

  No special settings on E20.

• PowerConnect M6220 switch cannot set port speed

  I'm trying to define a port speed to 100 instead of the default value of 1000 using the following command:

  1 the Interface Configuration mode enter to port 1.

  Console #configurer
  Console (config) #interface gigabitEthernet 0/1/1
  2. change the speed and duplex settings for the port.
  Console (config-if-article gi1/0/1) #speed 100
  Console (config-if-article gi1/0/1) full #duplex
  Console (config-if-article gi1/0/1) #exit

  But I got an error: "an invalid interface was used for this function." Please refer to

  

  Try to update the speed of the port on the GUI also returned an error:

  

  Could someone advise what I'm doing wrong? Thank you!!

  The user guide says that not all ports support all speeds, even if they are available in the command. And the output of the command is the message you see. What NIC connects to the interface 1/0/8? I think that most adapters for servers are 1 GB or higher.

• Question about Powerconnect M6220 and out-of-band/management 8024-K connection

  I'm sorry if this question belongs to another section, but with regard to the functionality of these switches I thought I would start here.

  My question is, the M6220 and 8024-K out-of-band connection are going through the connections on Board (for example port 18 for example) or through connection of the M1000e CMC?

  The reason for this question. We recently vlaned our network and CMC modules are VLAN 8 (10.100.8.0 255.255.248.0) and management of our switches is supposed to be on the VLAN 1 (10.100.1.0 255.255.255.0). I can't ping on the affected IPS (IE 10.100.1.15), but our CMC modules are fully accessible (IE10.100.9.120). Our blades are fully accessible and can access all the VLANS on them (they are the ESX host).

  Finally, I'm sorry if all necessary information has been provided, I'm not so much a networking guru.

  Thoughts?

  Thanks for your help

  The OOB interface is connected to the chassis management controller by the median plane of the chassis. Traffic on this

  port is separated from network traffic operating on the switch ports and cannot be lit or routed to the operational network.

• connect the m6220 switches stacked to existing Lan infrastructure

  I need to connect two powerconnect M6220 to LAN infrastructure existing.

  The switch of two are configured in the stack.

  Which is the best way to uplink the new switch to the other two powerconnect 5548.

  The old switch are not stacked and bound together by two 10GB Ethernet cable (one of the links is disabled).

  I need to implement the network tolerant to failures, maybe I need to configure the tree covering weight on the two links of 10 GB.

  I use Spanning tree to configure the uplink between the old and the new, too?

  Is there a better alternative? There is another way to prevent the loop network?

  Thanks, Francesco

  You have a few options.

  1. you can simply connect the cables between the M6220 switch stack and the 5548.  Set up a trunk connection which allows for VLAN needed overall.  Tree covering weight until it is enabled on the switch and not off on specific ports connecting the default switches prevent loops and allow the most profitable link to be active, leaving the second connection as an alternative link in a blocking state.

  2. you can configure LAG (aggregation of links).  This is where you configure the individual physical ports in a virtual port channel.  This indicates a covering tree to treat multiple physical ports as a single link aggregated to the other switch.  You will need to have the port at each end of the connection channel mapping. (On each switch).  This allows the same speed but more flow.  To move traffic more.

• Set up multiple paths to EqualLogic PS4000 iSCSI

  I have two Dell PowerEdge M610 in a PowerEdge M1000e that my team was given as units of seeds (thanks Dell) and we ended up buying storage, they sent with it, an EqualLogic PS4000.  The representative of Dell came and helped to get the basic running configuration and how iSCSI worked and showed us a doc (the same doc Configuring_VMware_vSphere_Software_iSCSI_with_Dell_EqualLogic_PS_Series_Storage.pdf noted many threads here) on how get v4.1 ESX (i) running with this storage.  We all stood up and running most of the time before he left, but after going on documentation, again, I have seen that we should be able to establish connections mutable and "Round Robin" to improve performance.  As I see so far in the two vSphere Client and in the management of the EqualLogic console console, I get only one per server (as seen on the attached screenshots).  I've been beating my head on this for the last few days trying to get the connections going.  In fact, I've seen it work once but for other reasons, I had to redo the raid on the host computer and reload and have not been able to get it working again... :'-(

  So, here's how the hardware is configured.  From the module of control PS4000 0, I have eth0 goes 1 Dell PowerConnect M6220 in the slot C2 chassis, eth1 goes to another port M6220 in C2.  If the storage is connected directly to the chassis.  And the same configuration on the modal control 1.  These ports connect to the vmnic4 & 5.

  Switch name Num used Ports configured Ports MTU rising ports

  vSwitch0 128 4 128 1500 vmnic0, vmnic1

  Name PortGroup VLAN ID used rising Ports

  The VM network 0 0 vmnic0, vmnic1

  Management network 0 1 vmnic0, vmnic1

  Switch name Num used Ports configured Ports MTU rising ports

  vSwitch2 128 6 128 9000 vmnic4, vmnic5

  Name PortGroup VLAN ID used rising Ports

  iSCSIMgnt 1 0 vmnic5, vmnic4

  0 1 vmnic5 iSCSI2

  0 1 vmnic4 iSCSI1

  ~ # esxcfg - vmknic - l

  Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

  Managing IPv4 10.131.172.74 network vmk0 255.255.255.0 10.131.172.255 00:26:b9:31:d6:a9 1500 65535 true STATIC

  vmk1 iSCSI1 IPv4 192.168.1.21 255.255.255.0 192.168.1.255 true 9000 65535 STATIC 00:50:56:71:e7:f5

  vmk2 iSCSI2 IPv4 192.168.1.22 255.255.255.0 192.168.1.255 true 9000 65535 STATIC 00:50:56:75:92:76

  ~ # esxcfg - NICS - l

  Name PCI Driver link speed Duplex MAC address MTU Description

  vmnic0 0000:01:00.00 bnx2 up to 1000Mbps Full 00:26:b9:31:d6:a9 1500 Broadcom Corporation of Broadcom NetXtreme II BCM5709 1000Base-SX

  vmnic1 0000:01:00.01 bnx2 up to 1000Mbps Full 00:26:b9:31:d6:ab 1500 Broadcom Corporation of Broadcom NetXtreme II BCM5709 1000Base-SX

  vmnic2 0000:03:00.00 bnx2 up to 1000Mbps Full 00:26:b9:31:d6:ad 1500 Broadcom Corporation of Broadcom NetXtreme II BCM5709 1000Base-SX

  vmnic3 0000:03:00.01 bnx2 up to 1000Mbps Full 00:26:b9:31:d6:af 1500 Broadcom Corporation of Broadcom NetXtreme II BCM5709 1000Base-SX

  vmnic4 0000:05:00.00 bnx2 up to 1000Mbps Full 00:26:b9:31:d6:b1 9000 Broadcom Corporation of Broadcom NetXtreme II BCM5709 1000Base-SX

  vmnic5 0000:05:00.01 bnx2 up to 1000Mbps Full 00:26:b9:31:d6:b3 9000 Broadcom Corporation of Broadcom NetXtreme II BCM5709 1000Base-SX

  ... OK, after all that, here's another conclusion after tinkering with the network settings for vSwitch2.  If I change:

  0 1 vmnic5 iSCSI2

  0 1 vmnic4 iSCSI1

  ... à...

  iSCSI2 1 0 vmnic4

  0 1 vmnic5 iSCSI1

  The connection to the storage is lost... for a while.  About 5 min later I see the connection on the EqualLogic, but on the other port (eth0 to eth1).  So I don't know the connection MAY work, but just does not do both at the same time.

  So what I am doing wrong?  I tried to read on other threads, but haven't read the answer to this question.  Thanks for your help.

  There is a step in this configuration guide where you link all of your VMkernel ports to the iSCSI initiator.  You will remember to do this step?

  What looks like the output of the following control air: esxcli swiscsi nic list vmhba39 d

  You should see the vmk1 and vmk2 in there.

  Matt

  My blog: http://www.thelowercasew.com

• M620 IO CARDS

  Hello

  We have a client and that he wants to buy two new servers M620 blade with the following configuration:
  Fabric A - Broadcom 57810S NDC
  Fabric B - Broadcom 57810S NIC
  Fabric C - Qlogic QME2572

  In the meantime, he has the following configuration of the i/o Modules:
  Fabric A - PowerConnect M6220 x 2
  Fabric B - PowerConnect M6220 x 2
  Fabric C - Brocade M5424 x 2

  Question: New M620 blades are compatible with the current configuration of Modules e/s?

  The following message by DELL - Kevin Ho has been proposed as a response to "Re: M620 i/o CARDS:

  Quick response - YES, the M620 are compatible with your current configuration of the i/o Module.

  Long answer - Broadcom network you have installed are 10GbE, but they will work with 1GbE switches, you have fabric A and B.  The HBA Qlogic that you have will work as long as you have a fabric fiber c/o module.  Your list of configurations of the currently listed I/O module a Qlogic HBA, so assuming that it is actually a fiber I/O module, you should be fine.

• Console port (serial) on Powerconnect 6248 switch

  Hi all

  I have two powerconnect 6248 s. The first I've had for several months. The second, I just ordered recently.

  I can't go to the console in to the second switch. I use the same settings (minicom) and cable that I use regularly to connect to the first switch.

  Any thoughts on how to solve this problem? I don't see any startup dialog after resetting the switch 2.

  Thank you

  Looks like you have experienced just about everything that you can. You checked restarted cable, the emulator settings, confirmed working on the other switch, switch, and the default value and it still does not work. It sounds more like it could be a hardware problem with this port. Is the unit still under warranty?

• Need to buy a cable from the console to a SRW248G4

  I have a client with an installed SRW248G4.  We are unable to determine the IP address assigned to the switch and we need configure ports.  The client cannot find the cable from the console provided with the unit and I succumbed to find where I can buy one.  Anyone have any ideas?

  Thank you!

  the srw248g4 uses a regular db9 console cable. You can buy at any hardware store, just to check if the device uses a female or male.

• EqualLogic PS series console RJ45 cable pinout

  Hello world

  I have an Equallogic storage array to use for the test which I believe is a ps100e, with two controllers blue sata ports having back series RJ45. Nothing I've used so far has had any kind of traffic from them, then someone can help me with a pinout of the console cable that was included with the devices? (I got was the machine itself). I saw a few summaries puts online buy them, but I'm a bit of a hurry and don't have much of a budget, so I was hoping to do so they are considered non-standard.

  Thank you!

  Here is the pinout settings and baud.   Make sure that this flowcontrol is disabled on the serial port.

  We find this info on the site Web of Equallogic.

  The title of the solution

  Cable to the serial Console, identifying Type I, II controllers, the RJ-45 connector pinout

  Details of the solution

  Type 1:

  FRU PN IS 95-0444. Cable 'dongle' will have a white label with 51-0003-02 marked top. It is 10 inches long, black, with DB - 9 (M) money and a micro DB-9 at the other end.

  You can order the dongle as a Molex 83421-9052 reference number to search on google. You will also need to a modem cable Null to go with it, if you don't have one, easy to find, even the most Radio Shack has them.

  Type 2:

  FRU PN 95-0517. Cable will have a white label with 51-0008 marked top. It is 10 feet long, black with the RJ-45 at the other end and a DB-9 (F)

  Here is the pinout of the connector RJ-45 series of EqualLogic Type-2 (SATA 2 command Module):

  1 - DTR (out)

  2 - CTS (en)

  3 - chassis Gnd

  4 - RxD (in)

  5 - TxD (out)

  6 Sig Gnd

  7 - RTS (out)

  8 - DSR (en)

  In the current firmware versions we do not deliberately set, or answer, the control signals (DTR, CTS, DSR, RTS), then you must either configure the device you connect so that it ignores them, or provide telesignalisations the according to the needs.

  The series settings are: 9600 baud, 8 bits, 1 stop bit, no parity, no flow control.

• How to repair or replace the cable from the monitor on console 15fp

  We bought a KVM rack and keyboard with our Dell 4210 support about 2 years ago.  We have received "No Signal" for a while on the screen, and I finally had time to open the side of the basket and take a look.

  I see that the insulation of the monitor cable that is built into the console monitor was rubbed through and some of the money i wire mesh has been broken.  It is to the first bend of the cable guide and must have been rubbing.  I guess that's the cause of the error 'no signal '.

  I would like to replace the cable, but releasing the anchor on the middle of the back of the monitor seems impossible after removing all the hexagonal bolts around the perimeter.  I cut the label above the dimple found in the center of the screen back but found that there is not a fastener which can be manipulated.

  1. Is it possible to open this beast, if I can replace the cable?  I don't really have the budget for a new console.
  2. If it cannot be opened and closed and then after working on it, everyone is aware it is possible to connect with success a RGB cable?

  Thanks in advance for any advice on this.  Mike

  
  

• Not functional CONSOLE port - PowerConnect 6248

  Hello, I have a problem, it is impossible to connect to the switch through the console port 6248, could someone help me? In addition, how to reset the switch with the "reset" button on the front of the 6248 switch, please? (I don't know the IP address of the switch.) Thank you in advance for your help. Best regards, NeedHelpGFF

  Hello

  The request is resolved. For more information, we found another cable that was connected to a DELL device. The connection from the console port is now functional.

  Thank you very much for your help.

  / ! -To help other people, take the cable supplied with the device.