PowerConnect M6220 switch cannot set port speed

Similar Questions

• Router Wifi Smart AC1750 cannot set the full 100 WAN port

  I connect to a static IP address.

  After putting in the IP (static IP) settings the router does not receive speeds defined by internet provider (Logix Communications).

  After consultation with Logix, told me that the WAN should be set to 'Full 100' and I could not find this setting on the device.

  From now instead of a 50mbps down I get 10 Mbps download and upload 50mbps, so I guess the current WAN settings are 'Auto' on the AC1750 router WAN and cannot be changed?

  So now I'm getting data collisions and slower than expected internet.

  I need to know if it's fixable or to return this product for refund. I've updated the firmware for more later, still no dice.

  I confirmed that my internet provider has no problem with a much older Linksys router with WAN set to 'Full 100'.
  Thank you.

  jjbraunius wrote:

  I connect to a static IP address.

  After putting in the IP (static IP) settings the router does not receive speeds defined by internet provider (Logix Communications).

  After consultation with Logix, told me that the WAN should be set to 'Full 100' and I could not find this setting on the device.

  From now instead of a 50mbps down I get 10 Mbps download and upload 50mbps, so I guess the current WAN settings are 'Auto' on the AC1750 router WAN and cannot be changed?

  So now I'm getting data collisions and slower than expected internet.

  I need to know if it's fixable or to return this product for refund. I've updated the firmware for more later, still no dice.

  I confirmed that my internet provider has no problem with a much older Linksys router with WAN set to 'Full 100'.
  Thank you.

  Just a heads-up... No domestic router vendors provide ports that you configure manually, they use all the settings of auto-negotiation. So, your ISP will have to adjust their speed of port auto, or provide you a taking router support port speed settings...

• I'm doing slideshows to music with an opening, I would switch to LR, but you cannot set the duration of each slide (in my case the score) based on listening to the music. (In the opening by clicking on the "stopwatch" and pressing enter at each change of

  I'm doing slideshows to music with an opening, I would switch to LR, but you cannot set the duration of each slide (in my case the score) based on listening to the music. (In the opening by clicking on the "stopwatch" and pressing enter at each change of image). Adobe staff question: can I expect to find this option in a future release?

  Hi Pcaubi,

  There is no such updates for the same from now.

  I suggest you to please put in a feature request to: Photoshop community customer family

  Kind regards

  Tanuj

• PowerConnect M6220 problem without tag switch of VLAN

  Good afternoon.
  I do not have much knowledge of networks and need help.
  M6220 have this connected to a HP ProCurve switch switch connected by a trunk.
  My problem is that I can not pass the 10 untagged procurve VLAN to the M6220 switch, can you help me?
  M6220 has firmware version 1.
  Thank you

  On a network connection VLAN native is the VLAN used to send and receive packets not marked. Here is an example of the configuration.

  Console (config-if-article gi1/0/1) #interface item in gi1/0/24
  trunk mode console (config-if-article gi1/0/24) #switchport
  Console (config-if-article gi1/0/24) #switchport trunk vlan 10 native
  trunk allowed vlan #switchport console (config-if-article gi1/0/24) add 10,11,12,13

  If trunk mode does not work, you can also try to use the general mode.

  Console (config-if-article gi1/0/1) #interface item in gi1/0/24
  mode console (config-if-article gi1/0/24) general #switchport
  Console (config-if-article gi1/0/24) #switchport general pvid 10
  Console (config-if-article gi1/0/24) #switchport general allowed vlan add 10 untagged
  Console (config-if-article gi1/0/24) #switchport general allowed vlan add 11,12,13 tag

  Hope this helps

• connect the m6220 switches stacked to existing Lan infrastructure

  I need to connect two powerconnect M6220 to LAN infrastructure existing.

  The switch of two are configured in the stack.

  Which is the best way to uplink the new switch to the other two powerconnect 5548.

  The old switch are not stacked and bound together by two 10GB Ethernet cable (one of the links is disabled).

  I need to implement the network tolerant to failures, maybe I need to configure the tree covering weight on the two links of 10 GB.

  I use Spanning tree to configure the uplink between the old and the new, too?

  Is there a better alternative? There is another way to prevent the loop network?

  Thanks, Francesco

  You have a few options.

  1. you can simply connect the cables between the M6220 switch stack and the 5548.  Set up a trunk connection which allows for VLAN needed overall.  Tree covering weight until it is enabled on the switch and not off on specific ports connecting the default switches prevent loops and allow the most profitable link to be active, leaving the second connection as an alternative link in a blocking state.

  2. you can configure LAG (aggregation of links).  This is where you configure the individual physical ports in a virtual port channel.  This indicates a covering tree to treat multiple physical ports as a single link aggregated to the other switch.  You will need to have the port at each end of the connection channel mapping. (On each switch).  This allows the same speed but more flow.  To move traffic more.

• PowerConnect M6220 ACL issues

  Hi, received a pair of blade switches PowerConnect M6220, pretty much the same as 6224

  I try to apply ACLs in interface, and I'm unable to do so.
  Here's what I'm trying to do:

  coresw (config) #access - internet-out list deny ip any 10.0.0.0 255.0.0.0
  coresw (config) #access - list on the internet permit each

  coresw (config-if-article gi1/0/17) #ip group-access internet-output

  Error when processing the ACL.

  coresw(Config-if-Gi1/0/17) #.

  <190>MAR 25 00:37:12 10.128.101.1 - 1 DRIVER [126512544]: broad_acl.c (1611) 4% ACL not applied to 134217728 port

  In this switch or on any interface on the switch, there is no other ACL.
  As you can see, it is a LCD 2 lines in the 90s, who refuses to work. Basically, what I'm trying to do is filter all local ip traffic.
  I'm doing something wrong here? According to www.dell.com/.../pwcnt_IP_ACLs.pdf , I can filter output destination.

  Any help is appreciated, thanks.

  I was able to test this on a M6220 and I can confirm the behavior you're seeing is a hardware limitation. IP based ACL cannot be applied evacuation. You should have no problem in applying the penetration.

• reset the password on a Dell PowerConnect M6220

  Hello, I'm trying to reset the password on a Dell PowerConnect M6220.  Can connect to the CMC via the https Web page, I don't see how to do it from there.

  Then I'll try to plug a USB serial cable into the console port and reset the password via a console session using teraterm but when I do that all I get is a white screen.

  Parameters of the series are:

  Cable: The Null Modem

  Bits per second: 115200

  Data bits: 8

  Parity: None

  Stop bits: 1

  Flow control: no

  Any ideas on how I can access telnet access to the device to reset the DDT successfully

  Thank you

  Kevin

  You can connect to the console port internal to the switch via the CLI of CMC

  Telnet to the CMC, then connect switch-a1 (a2 or b1 etc. etc.)

  This will give you the > invites, so either delet the startupconfig and recharge it, or put into you own username and password - remember that you can set on the schema of the interface of the band or band in slecting the appropriate interface

• Satellite A30 - cannot set up the binding wireless modem

  Hello
  I have a satellite a30. I just upgraded to broadband and cannot configure the WiFi wizzard. the modem is working perfectly thanks to threads, but cannot set up wireless despite my efforts! Please can someone help?
  see you soon
  Claire

  Hello

  What's the problem?
  You are not able to see the thread or what?

  Are you sure of the laptop and built-in wireless network card?

  Remember that the WiFi card is optional on the Satellite A30 and not all models includes the Wlan miniPCI card
  Thanks for posting more details!

  PS; If the laptop supports a WLan card internal, you should check only that steps;

  -Check if the WLan adapter is enabled on the laptop. Activate the switch on the side of the laptop and the FN + F8 key combination!
  -Check if the windows own WLan configuration is marked
  -Be sure that you use the right WLan encryption and whether encryption is supported by WLan modem (router) and wireless network card
  -Check if the standard 802.11 WiFi, B or G is accompanied by WLan modem (router) and wireless network card
  -Make sure that the router MAC filtering option has been disabled!

  As you can see all of these options are important to connect to the wireless LAN.

• RN314 cannot set up alerts

  Just I have an open for this support ticket and I'm getting nowhere fast at the moment, while the community has been so useful until now I was wondering if someone here could help/advise.

  -For the NASs x RN31400 2 I am owner and you have registered with you I am unable to setup e-mail alerts. I tried to use 3 e-mail addresses of 3 service providers: Yahoo, Hotmail/Outlook and also my own ISP TalkTalk email providers. No matter what settings I use for all 3 e-mail providers, I get the following error message: check the settings of the smtp server cannot send a code error message 5008010002 msmtp test e-mail alert on my 3 x NV + s very well using my Yahoo e-mail address work. On one of the RN31400s using Yahoo worked initially and the alert section would say that it has been configured correctly and I'd get emails to my 2 hotmail addresses, it was on 1 of my RN31400s on the other RN31400 the settings would save not and always say, there was a problem but I had managed through test messages. Now, no matter what settings I use, which email provider I use, etc. I can't e-mail job alerts! Please help because this is obviously a problem with the NASs and the software on devices, the version of the firmware on two is 6.4.1 Ive set up the addresses of 3 E-mail on an e-mail within my network client and all 3 work well, the 3 x NV + s do not have a problem using my Yahoo account to send alerts check my routers and firewalls there is no blocked traffic and I can't telnet to Server 3 Messaging without problems. Please advise/help, thanks.

  And...

  OK the update of the firmware did not work, I have one of the update firmware version 6.4.2 RN31400 and after 2 reboots, I am still unable to receive job alerts.

  The I am using SMTP servers are:

  Yahoo =
  ------------------------
  Email provider: Custom
  User: [email protected]
  Password: xxxxxxx
  SMTP server: smtp.mail.yahoo.com
  SMTP port: I've tried 25, 465, and 587
  From: [email protected]
  Use TLS: I tried checked and unchecked

  Hotmail/Outlook.com =
  ------------------------
  Email provider: Custom
  User: [email protected]
  Password: xxxxxxx
  SMTP server: smtp - mail.outlook.com
  SMTP port: I've tried 25, 465, and 587
  From: [email protected]
  Use TLS: I tried checked and unchecked

  TalkTalk = it's the ISP I use!
  ------------------------
  Email provider: Custom
  User: xxxxxxx@TalkTalk,net
  Password: xxxxxxx
  SMTP server: smtp.talktalk.net
  SMTP port: I've tried 25, 465, and 587
  From: xxxxxxx@TalkTalk,net
  Use TLS: I tried checked and unchecked

  Ref: browser, I used Firefox and Internet Explorer, not that it should make no difference whatsoever.

  Ref: screen captures, don't need the parameters are listed above for the two RN31400.

  Ref: parameters for the NV 3 x + an are as follows:

  Yahoo =
  ------------------------
  Email provider: Custom
  User: [email protected]
  Password: xxxxxxx
  SMTP server: smtp.mail.yahoo.com
  SMTP port: 465
  From: [email protected]
  Use TLS: Is checked and

  Test of the emails for the configuration of alerts on the NV + s are still working fine, DO NOT WORK for the RN314.

  Please tell us what can be done to solve this problem, thank you.

  And...

  Full error message =

  Unable to send a test message.

  Unable to send a test message. Check the settings of the SMTP server. Code: 5008010002 error msmtp

  DateTime: 05:02:09 04/02/2016

  And...

  Hello

  Just right now I can read the KB article - which does not help somehow:
  KB.Netgear.com/app/Answers/Detail/A_ID/23066

  There is nothing wrong with the configurations that I use.

  All 3 servers SMTP and the above settings work very well on my NAS NV +.

  All 3 servers SMTP and the above settings work fine on Outlook or Mozilla Thunderbird's within my network.

  All servers SMTP 3 and address listed above work fine when I Telnet to them within my network.

  First settings of Yahoo SMTP worked well on one of the RN314 and seemed saved and ok.

  Also...

  At the beginning of Yahoo SMTP settings worked well on one of the RN314 but not record or say that it has been configured correctly.

  Then obviously there is something wrong with the SMTP service/server on these NAS RN314 2 bed.

  I am not willing to allow you access as it will provide no benefit whatsoever.

  For the course of 20 years, so it's nothing that can be done with you giving remote access with the exception of confirm you what I have already said previously, I have worked in it.

  And...

  So please advise what Netgear will do then or advise what other other confirming my settings allow remote access?

  Your forums to research it seems that problems with mail like this are apparently quite common, so what has already been done to solve the problem?

  Also the error code: Code: 5008010002 error msmtp

  Why you are not this survey with your development teams who wrote the OS on the NAS working on what actually the error means?

  There is nothing wrong with the configuration that it works very well on my 3 x NV + NAS, it works very well in e-mail clients, it works very well in Telnet, and it worked very briefly on the 2 x RN314 of for of Yahoo SMTP settings.

  Eron - if you are unable to help further please add this problem to your support line... 3rd line?

  Thank you.

  And...

  I also tried my account GMAIL apps less secure according to this thread the value:

  https://community.NETGEAR.com/T5/using-your-ReadyNAS/cannot-set-up-alerts-on-my-ReadyNAS-RN314/TD-p/...

  GMAIL =

  ------------------------
  Email provider: Custom
  User: [email protected]
  Password: xxxxxxx
  SMTP server: smtp.gmail.com
  SMTP port: I've tried 25, 465, and 587
  From: [email protected]
  Use TLS: I tried checked and unchecked

  If this does not work on the RN314 but it works very well on the NV + of via Telnet and in an email client (x 2)

  Please escalate to your next level of support, thank you.

  Right, I have fixed on one of the RN314 far...

  I backed up all my data on this RN314 and did a factory default.

  I have reproduced the RN314 settings manually then nonworking time for the reset RN314 except for identification data, i.e., name, etc.

  Exactly as it was before... and now the RN314 in default works fine.

  I am currently backing up the data on the RN314 now inactive to perform a Setup factory on that one and see if that solves the problem on this one here.

  Then we can close this and I will refer to it with a new thread if I need if the second RN314 still has problems after the default settings.

• WAG54G2 - port speed

  Hi all

  I have recently buy this router and I need to set the speed of the eth port (a cable is very long you have to fix at 10 Mbps...) but can't find any method of web interfaces.

  I need address dhcp reserved also for question natting and firewalls, but I read that is not yet supported.

  Is there a way of working? I give this store router?

  Thanks for the cut & paste support

  but it is not yet an upgrade to this firmware...

  Well, I think it's better to close this thread, rather than be fooled

  u c

• The question of the Uplink port speed

  Hi there guys!

  I want to set my 4 GB uplink port speed, but the UCSM show me only 1/10/20/40 GB. How do I change the port speed trought CLI?

  Greetings.

  Here's our UCS 2.0 running and I am able to adjust the speed of uplink FC

  ucsfi-01-A / CF-uplink/fabric/port-channel # show in detail

  Port channel:
  Channel port Id: 255
  Name: ucs-n5k-pc255
  Admin State: enabled
  Oper State: to the top
  Admin speed: Auto
  Oper speed (Gbps): 32

  ucsfi-01-A / CF-uplink/fabric/port-channel # set adminspeed
  1 Gbps 1 Gbps
  2 Gbps 2 Gbps
  4 Gbps 4 Gbps
  8 Gbps 8 Gbps
  Auto Auto

• ADFC-10004: cannot set property managed bean "autoquery.

  Hello
  
  I'm trying to deploy and run an ADJ application that was built with JHeadstart. Initially, I came across the question which the application appears to hang in the browser when I first tried to see. The URL change the request parameter and a reload triggered JavaScript happens constantly - page content is empty. I could solve this problem by using the suggestion offered in this thread:
  
  Re: JDeveloper 11.1.1.2 group patch
  
  After the page is loaded (Yes!), but when I tried to load the next page making connections to database tables, I get this stacktrace and the page remains empty:
  
  Caused by: oracle.adf.controller.ControllerException: ADFC-10004: cannot set property managed bean "autoquery.
  at oracle.adfinternal.controller.util.Utils.createAndLogFacesException(Utils.java:184)
  at oracle.adfinternal.controller.beans.ManagedBeanFactory.setSimpleProperty(ManagedBeanFactory.java:316)
  at oracle.adfinternal.controller.beans.ManagedBeanFactory.setManagedProperties(ManagedBeanFactory.java:262)
  at oracle.adfinternal.controller.beans.ManagedBeanFactory.newInstance(ManagedBeanFactory.java:203)
  at oracle.adfinternal.controller.beans.ManagedBeanFactory.instantiateBean(ManagedBeanFactory.java:860)
  at oracle.adfinternal.controller.state.ScopeMap.get(ScopeMap.java:82)
  at javax.el.MapELResolver.getValue(MapELResolver.java:164)
  at javax.el.CompositeELResolver.getValue(CompositeELResolver.java:143)
  at com.sun.faces.el.FacesCompositeELResolver.getValue(FacesCompositeELResolver.java:72)
  at com.sun.el.parser.AstValue.getValue(AstValue.java:118)
  at com.sun.el.parser.AstNot.getValue(AstNot.java:46)
  [snip]
  Caused by: java.lang.NoSuchMethodException: unknown property 'autoquery.
  at org.apache.commons.beanutils.PropertyUtilsBean.setSimpleProperty(PropertyUtilsBean.java:1741)
  at org.apache.commons.beanutils.PropertyUtils.setSimpleProperty(PropertyUtils.java:577)
  at oracle.adfinternal.controller.beans.ManagedBeanFactory.setSimpleProperty(ManagedBeanFactory.java:308)
  ... more than 232
  
  I checked in JDeveloper properties JHeadstart ask "Change the JHeadstart Application definition". Looking at my details group values, I see that the "automatic query" is checked in all cases. I tried to remove the check mark and redeployed, but the same error happens again.
  
  At the moment I don't know how to debug this more. The last error is possibly caused by the fix that I applied (removal of the filter to ADF faces)? Any ideas how to proceed are welcome. :)
  
  Environment:
  JDeveloper Studio Edition Version 11.1.1.2.0
  JHeadstart 11.1.1.2.37
  WebLogic 10.3.2.0, running locally on my Windows XP machine

  To start, can you still run the application within JDeveloper?
  Second, switch to a later version of JHeadstart recently?

  In the past, the JhsSearchBean used to have an autoquery property. If your managed bean definition still contains this property, you get the error you mentioned.
  You must remove this property of any beans that are controlled using the JhsSearchBean class.

  Steven Davelaar,
  Jheadstart team.

• Satellite M100: Cannot set the resolution 1368 x 768 on external LCD screen

  Satellite M100-179
  Graphics - ATI x 1400 card.
  Cannot set the resolution 1368 x 768 on connected usung Sub - D LCD TV Samsung 32R72
  There is no resolution 1368 x 768 in the available resolution list.

  The graphics card hardware support different screen resolutions, but if the driver doesn't contain this resolution of the screen so that you cannot choose it.
  I think so you re not able to choose this special resolution on the external display.

  In my opinion it has nothing to do with the graphics card or with the screen, but only with the graphics driver.

• Tecra A4: Cannot set the resolution of 1280 x 800

  Hi all.

  I have a Tecra A4, and for the last 2 days I am trying set up the screen at native resolution of 1280 x 800, without sucssess.

  I try a lot of things, like updating drivers, use the restoration of the system, the value 'stretch' in the BIOS, etc, but this resolution do not appear on the display settings (I use XP SP2). I've only 800 x 600 and 1024 x 768.

  In any of these resolutions, a wide black border appear to the right of the screen. A small border appears on the bottom, too.

  Please, how can I solve this problem? I don't want to use the Toshiba restore, some programs I use are very difficult to find and install.

  Thank you.

  You cannot set this resolution if this resolution of 1280 x 800 is not part of the display driver.
  The graphics card driver contains all available resolutions and if one is missing, I mean not rated, it s not able to select

  Nothing to buddy

• Cannot set up eprint

  Cannot set up eprint.

  My printer was working with eprint very well until I got a new router. Since I can't not to use or setup eprint.

  It is connected to the home network wireless and it works fine for printing documents.

  I have reset the factory for Web services settings, but still no luck. Continue to flock to the top that I'm not connected to a network and wants a proxy

  Can anyone help

  Thank you

  Hello

  The valid IP address would start by 192.168 if the IP address starts with 169 or something else is not a valid IP address.

  If the address of your router is 192.168.1.1 then the IP of the printer should be something like 192.168.X.X

  OR

  If your laptop is connected to multiple networks, this problem may occur. Please connect your laptop to only if the wireless network to which the printer is connected, try anything again.

  Kind regards

  Olilloyd