Print head and Officejet 6500 ink system failure problems

Similar Questions

• OfficeJet 7612: Ink system failure HP Officejet 7612

  My printer is just over a year and it stopped printing. I went through all the steps suggested when this happens with the exception of the driver/software update, the printer will not accept as he says he is busy. Closing he took off and turing back on does not change the result. There is something practical to do rather than running the window of the printer and not to buy HP printer again?

  I managed to solve the problem using a PIN. Best I could conclude, was plugged the hole in the ink of the cartridge to the print head, and all that was needed was to push a PIN into the hole. I had hoped for such a practical solution of HP, but nothing has been documented or provided. It would be a crime to throw an essentially new printer for a light socket!

• HP Officejet 6600 e-all-in-one printer - H711a/H711g 'Ink system failure', will not print computer

  At first, it was just a problem with do not print from the computer.  Error messages had to do with the failure of the print head or do not find print head, etc..  After going through several different controls online, download the scans, etc., it does not at all, print showing an error message "ink system failure".  I tried to remove and reinsert the 4 printheads (black 932, 933 colors) and turning market and check the caps and unplug the power.  Since this is a wireless network, I can't unplug the USB.  It was the OK signal.  Now, with this error message, I don't see the home screen printer controls.  It just says: put it on and then contact HP.  Help, please.  Very frustrated (it didn't happen all at once - a first he wouldn't print from the computer sometimes, other times.)

  Wildrat58,

  If you get ink system failure and you've been through the steps that are listed in the article above the printer may require troubleshooting. You can reach support - 800-474-6836. If you do not live in the United States / Canada region please click the link below to get help from your region number. http://www.hp.com/cgi-bin/hpsupport/index.pl - for the maintenance options.

  Good luck!

• My HP printer has an ink system failure, what can I do to fix this?

  Hello

  I'll do a tutorial on how to solve the error message ink system failure.

  Now, in general this error can occur when the ink cartridges are bad, the printhead is damaged or the sensors are indicating that the ink system has failed to the printer.

  

  Step 1:

  The first step we take with an ink system failure problem is a hard reset with the printer. A hard reset Resets the sensors inside the unit causing the sensors reading if the print head or ink cartridges are healthy or not.

  Hard Reset:

  Unplug the power cord from the printer and the wall

  Wait for 30 seconds

  Plug the power cord into the printer, and then on the wall (do not plug power cord into a surge protector)

  
  Step 2:

  Now, if the hard reset doesn't fix the problem there are a few available documents to follow which will guide you through a few steps to try to resolve the printer.

  I will list a couple of them here:

  If your printer does not appear please go to HP support and drivers and search for your printer and your document.

  Photosmart C7280

  OfficeJet Pro 8600

  OfficeJet 6500 Wireless

  Step 3:

  If none of these documents allows to solve the issue, I would call HP @8004746836. They should be able to help you replace or repair the unit. This could result in the replacement of the printhead, if so please be aware that if you are out of warranty, it will cost you.

  Remember if you find one of my post useful or want to say thanks don't forget to click the White Star under my name to give me congratulations.
  I really appreciate it!

  Thank you!

  I hope it's useful!

  Remember if you find one of my post useful or want to say thanks don't forget to click the White Star under my name to give me congratulations.
  I really appreciate it!

  Thank you!

• I get the 0xc19a0042 ink system failure on my HP Photosmart B210 printer

  I followed the instructions for disassembly and cleaning the printhead twice, as well as to disconnect and reconnect and the 0xc19a0042 ink system failure message continues to show and I can't print or scan with my B210 printer. I now seek to replace the print head, but could not find the info on all the links from HP that I have searchded. Any help suggestions greatly appreciated.

  And if you are in the United States and want to order it from the hp online store: http://www.shopping.hp.com/en_US/home-office/-/search-Browse?SearchParameter=%26%40QueryTerm%3DPhotosmart%2BB210%2Bprinthead%26prodsubgrp%3DPrintheads&PageSize=15&SearchTerm=Photosmart+B210+printhead

• ink system failure 0xc19a0022 7500 e910

  I order this printer online thanks to Hp and I just got this week.  I am a system admin, and I install that several printers and ink cartridges but I have not encountered this error before.  I buy 7500 e910 and East 0xc19a0022 ink system failure.  I need to know what to do with this error.  Thank you.

  I'm sorry you have a problem with your 7500 printer ink system failure.

  This happens usually when the cartridges are damaged, or needs to be cleaned. Sometimes the print head is clogged or it is bad.

  Try to take the printhead on the own contacts with water and lint.

  Here is a link that can also help you with this problem.

  http://support.HP.com/us-en/document/c03081973

  Let me know if it helps.

• Ink system failure Officejet 6500 (no error code specified)

  Ink system failure Officejet 6500 (no error code specified)

  I have turned off the machine on again (and it doesn't)

  I turned off the computer and unplug the unit (and it does not fix it)

  Without specific error code I'm not sure what to do

  Hi CHCA. Your Officejet 6500 must be out of warranty? You can doublecheck the warranty status of your printer here: http://h10025.www1.hp.com/ewfrf/wc/weInput?cc=ie & lc = on -if it is still under warranty, you should not pay for a new printheaad.

  But if your printer is no longer under warranty, you buy one a. The part that you really need to order an Officejet 6500, is CN643A. If you are in the United States, here are the HP part store page where you can order the new print head Assembly: http://h20141.www2.hp.com/HPPARTS/Search_Results.aspx?mscssid=C580393F30964EDD82B16A5C641BEC41 & Searchin' PartNumber = & SearchPN = CN643A

  If you are not in the United States, start from this page: http://welcome.hp.com/country/us/en/wwhowtobuy.html , specify your country and search for CN643A.

  Also, here is a support document that should help you with the replacement of the print head: http://support.hp.com/us-en/document/c01643079

  I work with HP but my messages and responses are mine.

• ink system failure officejet 6500

  make system failure ink on officejet 6500, changed the cartridges, activated and deactivated

  I am writing to everyone affected by a FAILURE of the SYSTEM of INK message.  I use a 6500 and my wife has a wide 7500 a carrige. The 7500 had an ink system failure. I tried everthing recommended with no luck.  My wife needs a printer to work more than I do, I went to get out them.  Given that the power supplies are the same I have left in place.  Guess what?  The 6500 came with an ink SYSTEM FAILURE as soon as it was powered by the power of 7500.  I changed the power supply and everything works fine.  I tested the 7500 on feeding of 6500 and no ink system failure more.   I have not measured the voltage on the power supply that seems to cause the ink system failure, but I recommend you try a new power supply before you buy a new print head.  Check ebay and amazon for a nice price.

  Hope this helps someone else.

• HP Officejet 6500 E709n: HP Officejet 6500 E709n - ink system failure error message.

  I have a printer HP Officejet 6500 E709n.  I get the following error message when I turn on the printer:

  'Ink system failure.  "Please turn printer off, then on.

  I then do as instructed and turn the printer off, but then the whenever I re - turn on the printer, I get the same error again.  The printer is now fixed to the top and none of the buttons on the printer works except the Power button on / off.

  Any suggestions on how to proceed?

  Hi @recooke,

  Welcome to the Forums of HP Support! I see that you can not use your HP Officejet 6500 Wireless. You get a printer fault to "turn printer off and then on again" you did without success.

  Please perform a hard reset:

  1. disconnect all cables and cards of memory in the printer.  Unplug the power cord, directly from the back of the printer when the printer is still on.

  2. unplug the other end of the power cord.

  3. If there is a power supply on the power cord, disconnect one end and reconnect it.
      
  4. at the end of 60 seconds, plug it directly into a wall outlet (not a surge protector or battery backup).
      
  5. connect the power cord to the back of the printer.
      
  6. the printer should automatically power back upward.  If not, turn it on with the power button.

  7. try to make a photocopy (if your printer is an all-in one) before you connect the cables from the printer.

  8. connect the other cables needed to the printer.

  It is recommended that the printer is plugged directly into a wall socket to ensure a uniform level of power.  Sometimes, when plugged into a surge protector or battery backup, the quantity of electricity is not received by the printer.  Power problems can cause printing problems.  It is particularly important to be plugged directly into a wall outlet with wireless connectivity problems, "sleep mode" and other power problems.

  Any change?

  If you still see the error, please check your Inbox. I sent you a private message on the Forums.

  Response with the result. I hope this helps.

  Just say thank you, please click the ' Thumbs Up ' button.

• Ink system failure error Code 0xc19a0013 HP Officejet 6500 has

  Printer has stopped printing in black ink: get a gray tone or no impression.  Get higher up the ink system failure error.

  Reviewed the help pages and have installed new black ink cartridge, check the squares of all the cartridges, clean the print head menu Tools, removed the print head and cleaned manually, unplug the power supply etc. Considered the responses on the forum pages. A ran HP print and Scan doctor.  I consider when buying a new print head or a new printer, any other suggestions? It's only black ink.  I ran a test page and the black box of the ink is interesting: instead of going from the darkest to the lightest he's going from light to dark to light again.  Thank you, Sue S.-S.

  You're welcome Sue

  See post below on Bob soak the printhead...

  http://h30434.www3.HP.com/T5/other-printing-questions/Photosmart-premium-C309a-black-prints-out-green-on-photo-paper/m-p/449245/highlight/true#M28673

  (1) get a pan and put 1/2 "of very hot (not boiling) water in the bottom.
  (2) remove all ink cartridges, then remove the print head Assembly.
  (3) gently put the printhead nozzles down in water and soak for 5 minutes.
  (4) remove the print head and gently dry the electrical contacts.
  (5) replace the print head in the printer and then reinstall the ink cartridges.

• brand new officejet pro 8600 e - all - in - one, ink system failure msg, msg lack cartridge...

  told to turn off the printer after ink system failure msg, but then gives a cartridge can fail to msg and said that the printer can be damaged if turned off.

  The printer is brand new. I print a dozen test pages fine... haven't touched inks since installed first. When I open the cartridge access door, inks/heads move to the opening, so I can't reinstall the cartridges. Help!

  The document here can help.  You'll need temporarily ignore the message about not to turn off the printer...

• HP Office Jet 6500 E709a Series says ink system failure

  my HP Office Jet 6500 E709a Series says ink system failure. Turn the printer off of the ndo. does not resolve made 3 times. Have unplugged the device and removed and reinstalled ink cartridges. nothing works

  Original title: printer print

  Please take a look at

  http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01458034&cc=us&lc=en&dlc=en&product=3795314&tmp_track_link=ot_search#N99 .

• The message on printer ink system failure

  Spoiler (Highlight to read)

   

   

  Have a message to get HP Office jet 6500 on printer ink system failure

  Anyone?  Thank you

  Peebles

  There is a document for ink system, for the Officejet 6500 failure, found here.

  Hope it will help Peebles.

• Printer HP Photosmart Plus Plus shows continuously "ink system failure - 0x19a003e.

  I bought my computer Mac and HP Photosmart together, as it was advised the best printer for Mac.

  Since I get the above error message. Can get 1 week of printing, before the error message appears.

  Had replaced print head, printer sent replacement, another print head has published and now waiting on my 2nd replacement printer.

  I followed the HP guides when I receive messages error, but without success.

  My children have a HP Deskjet which I use without any problems on my Mac?

  Because the printer is not so old and still under warranty, HP replaces it, but I'm sick of not having a printer that works every time and duty wait for replacements...

  Any suggestion from anyone that I could get hurt?

  Or what I can try?

  I get to the stage where I can request a full refund

  Hi Truckiem,

  If I'm not wrong you use: HP Photosmart Plus e-All-in-One Printer (B210a) and you get an error message 'Ink SYSTEM FAILURE' on the screen touch printer.

  You will see the small icon home and U turn the arrow on the touch screen of the printer which is invisible

  Please complete step on touch screen of the printer and, if you are below the following step, make sure that both buttons are invisible.

  Tap the Panel to order 4 times in that order

  Tap the inverted arrow / U turn key lower left (BL)
  Then press the small icon of home top left (TL)
  Tap the inverted arrow / U turn key left lower BL
  Then, once more to touch the opposite arrow / U turn key lower left (BL)

  You will see Menu Support displayed on the touch screen of the printer, and then press OK

  Support touch - Touch OK, use the button to the right and select Menu Reset - Touch OK, use the ScrollBar or the right arrow to select Reset SEMIFULL - the printer turns off automatically.

  Then turn on the printer manually

  Select the language: English

  Country: USA

  If you get the same ink system failure error message, it seems to be a problem with the printhead Assembly.
  Or you can replace the printer of the store where you buy or contact HP Chat support or voice and have it replaced.

• OfficeJet 7500 has E910, "ink system failure".

  I have 2 Office jet 7500 a E910; I get 'ink system failure', the other works well; I take the printhead that is OK, I put it in the other: 'ink system failure '; I just got back from the other unit and no problem. I tried to unplug and reconect, same error. I tried to reset the printer, the same mistake; I cleaned with cleaning paper for lenses from contacts inside the print head holder, same error. What more is needed?

  Hey there!

  Thanks for getting back to me!

  I understand that the question much better now thank you for the clarification. So the problem is with the 1 printer, you take the printhead of the printer to work and put in the printer broke and he always says that there is a "ink system failure".

  These steps you have done certainly point to the printer in question. I highly recommend that you call Support technique Hp for help with this problem because they have more options for you I do. For a uniform 'ink system' on 1 unit you know has a printhead working in could be a clear sign of a fatal error.

  If you are in the Canada, U.S. dial 800-474-6836 or you can Contact HP worldwide.

  HP printers usually have a warranty of 1 year from the date of purchase, you can check the warranty using the following if you wish; guarantee cheque.

  I hope this helps. Please let me know the results. Have a wonderful day!