Printer HP Deskjet 3050 has prayer after installing new cartridge HP

Similar Questions

• Office Pro 8000: Cannot Print/Out of ink error even after installing new cartridge.

  When I tried to use my printer a few days ago, I received an error message "can't Print Can: ink" on the magenta cartridge.  I had used the printer a few days before and had not received a low ink warning.  It seemed suspicious to me that I would have received an empty cartridge error message without having previously received a low cartridge warning.  The cartridges yellow and cyan read 70% complete - all 3 were original cartridges.

  I bought a new cartridge 940XL magenta and installed according to the instructions.  Now, I get a message that the new 940XL cartridge is empty.  I can shake the old cartridge 940 and hear liquid inside.  Obviously, the new cartridge is also complete.  I tried to electric bike, reinstall the software, etc., without change of status.  If I swap back between the 940 old and new cartridge 940XL, they are correctly identified by type on my screen as the 940 or 940XL.  Because of the way the problem is presented, I don't think it is a cartridge problem.

  Of course, problem first awaken on May 8, and my warranty expired on 26 April.  Any suggestions?

  I solved my problem, what was obviously a lack of factory Assembly.  I looked inside my printer with a flashlight in the area where the ink cartridges are installed and found sprayed inside the printer magenta ink.  I disassembled the printer and found that the magenta line had been damaged during installation.  There are four tubes of ink that out by behind the ink cartridges, can do a U turn back toward the front of the printer.  Just after the bend, they do an another elbow top neighborhoods.  It is at this point that I found the damaged magenta line, directly above a screw on the right side of the housing of the ink cartridge.  The lines are in a very narrow passage and are held in place by several guards, moulded plastic.  It seems that the lines have been in place in the guardians, then the screws inserted from the top.  As I said, there is a tight passage, and it would be very easy to damage the line of ink right here if the lines have not been carefully selected to insert the screws when mounting.

  To solve the problem, I removed about 1/4 inch line damaged magenta ink.  I cut the line with a sharp razor, carefully to avoid collapsing the line or causing burrs to the hose.  I then placed approximately 3/4 "heat self-sealing tube on one end of the line of ink heat shrink.  Then I connected to the line with a small piece of plastic tube rigid of the handle with a swab of cotton, which was a perfect fit and comfortable on the line of ink.  Making sure not to cut the tube of ink or cause other damage, gently twisted the line of ink back until the ends have butted up inside the splice of cotton swab.  I then positioned the shrink tube over splice and it shrunk with a hair dryer.  Heat shrink tube, I used a hot melt glue applied to the Interior, which has helped more away making a watertight splice.  Again, it is not a lot of space, so the splice should remain small.

  I reassembled the printer, reinstalled ink cartridges and powered by the printer.  After the normal, long time running, I printed full color sheets and everything was fine.  Already that I had installed the cartridge magenta watch now that it is complete, and the remaining cartridges also read the levels they had before disassembly.

• DeskJet f4180: always E error message and empty cartridge light flashing after installing new cartridge

  I always get the error message E and empty flashing cartridge light after installing new black cartridge.

  Welcome to the @vinylzappaforum!

  I read on the 'E' and the empty cartridge light blinks after I installed a new black ink cartridge. If you have tried the guides that I suggested in our other thread here, so the next step would be to call phone support at HP to discuss your printer options coming with them. I let the info below.

  Please click the "accept as Solution" if we reached a solution and the "thumbs up" to say thank you for my help.

  Contact HP:
  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  File number and phone number appear

• After installing new cartridges, printer icon says printer is off line. Tried to go in the passage of the off-line online, without any change.

  The printer itself doesn't seem to be the problem. Have disconnected the cables, and the message is offline, offline. Reconnect and he said just in offline mode. This makes me think that it is a software that I'm not waking up switching.

  I did the online diagnostics and he thinks that the printer is turned off. But it's not. Were do form here?

  "After installing new ink jet cartridges.

  The problem began after you opened the printer.

  I suggest you contact the manufacturer of the printer.

  See you soon.

  Mick Murphy - Microsoft partner

• 10 the desire: desire 10 cannot adjust the print size after installing new cartridge

  After installing the new print cartridge (60XL) print size is very large: so far, I have unplugged the usb connection and power, reinstalled the cartridge a few times and run tests... I also went to control panel and looked at all the parameters, but find no way to adjust the size of printing... can anyone offer a solution... Thank you

  the solution: problem was with Firefox, when I switched to Chrome it prints perfectly!

• Misalignment cartridge after installing new cartridge

  On my J6480, the black print cartridge ink level was very low, so that impressions and copies were very poor. I do most of my copy in black, while during printing I use color. So I ordered another cartridge 74xl black and just to have a backup of color also decided to order another cartridge three-color 75xl. The current tricolor cartridge ink level went made just for the cartridge was still about 85% or more, then the black cartridge was approximately 15% or more before I replaced it.

  After getting my new black cartridge, I took the old one and put in the new. Then the printer ran on the new cartrdige alignment and alignment does not! After trying a few times I have replaced the old cartridge Habs, even if the Panel showed it to about 85%, the with a new and now alignment succeeded.

  Why would be to have an alignment to fail completely new black print cartridge, even with a tricolor cartrdige always at a fairly high level? The former Habs is still usable? Should I try to clean it and reuse it? I looked at my old tricolor cartridge contacts and they seemed fine. No idea why put in a new black cartridge fails with an old tricolor cartridge alignment, even if the control panel command shows the level of the Tricolor cartridge is high enough, would be appreciated.

  The alignment will fail if the colour and black cartridges will not print correctly.  I suggest you put the old cartridge in and then print a page of diagnosis as on the Six Solution of the document here.  If the color bars do not print correctly the steps described in this document can help solve the problem.

  Do not replace the Ribbon on regardless of the color cartridge, you let the printer, as this would cause a color mixture that will ruin the cartridge.  If you don't have a cartridge door, then store it as described in this document.

• Printer HP Deskjet 3050 a: decrease the size of the font in Deskjet 5030

  I'm changing the font size to a smaller size on a printer HP Deskjet 3050 has J611g.  My printer was printing to the appropriate size.  Suddenly, on a project he printed normall until it came to the last page, the date on which the font size became so great that only 1 or 2 letters would take on the page.  The next time I tried, each page was so great that only a few letters were on the page.  I don't know if I accidentally hit something or changed a setting that I should not have done, but I have no idea how to make to make it smaller.

  I tried Googling with the search term: how to change the size of the font on the printer HP Deskjet 305 a.  Almost all terms had to do with the increase in the size of the font.  I have quoted me a procedure on the eHow site, but it does not seem to apply to this particular model.

  I also tried to search the HP website problems.  Again, it would either mean that no search term

  has been found or each question had to do with the increase in font size.

  Any help would be greatly appreciated.  I have an important document to print, and I already spent two hours trying to solve this problem.  With my luck, it will prove to be something simple!

  Sorry only you know which software you use to print. When you select PRINT, this is the printer control software. You need to know how to find the font size and decrease and make sure that you are not in any type of "zoom" mode.

• Printer HP Deskjet 3050 a hesitate because long after command to print

  Printer HP Deskjet 3050 a hesitate because long after command to print.  How to fix this?

  Hello

  As OEM HP is responsible for the good operation of the printer and their
  drivers provided. Check with HP support, their documentation online and
  drivers and ask in their forums.

  Good luck, you need to update or reinstall the latest driver.

  HP support/troubleshooting & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  =============================================

  The main issue is probably the drivers, but these can help:

  Add or remove a printer
  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-printer

  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Open the printer Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Find the manufacturer's Web site
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-a-printer-manufacturers-website

  Find and install printer drivers in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• DeskJet 3050 has J611 all-in-one: Mac cannot connect to the printer using the wireless configuration

  My printer is connected to the same network as my Mac. When you complete the Setup wireless using a USB in system (HP Utility) preferences, a message says: "wireless network settings have been successfully downloaded to your device. However your Mac could not locate the device on the network. »

  I did everything I could: restart the printer. Unplug the printer and reconnected on the network and configuration of try again several times.

  Help?

  Hey @benjaminllim,

  Welcome to the Forums of HP Support!

  I understand that you have some problems with the connection of your Deskjet 3050 has e-all-in-one printer to your computer Mac OSX 10.11. I can help you with that.

  To start, make sure that the printer is plugged directly into a wall outlet, not a surge protector. Once done:

  1. Turn the printer off:
  2. While the printer is turned off, disconnect the power cable from the back of the router for a minute.
  3. When the lights come back on the router, turn on the printer.
  4. Disable any antivirus, firewall or security of your Mac software.
  5. Try to run the installer.

  Please let me know the results after following the above. If you are able to print to the printer, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• Why can not install HP DESKJET 3050 has in a series of J611 on my new computor windows 8

  What can I do to make my existing HP DESKJET 3050 has all in one printer to work on my new computer windows J611 series 8 when I put in the disk says it is not compatible in some way?

  Get the updated drivers from HP for Win8:
  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-109013-2&cc=us&DLC=en&LC=en&OS=4132&product=5298986&sw_lang=>

  As with all HP printers, the software must be installed before connecting the printer. Installation will then ask you to connect via USB. If you have installed all previous versions, uninstall them first.

  I have this same AIO, and new long pilots work fine.

  SC Tom

• DeskJet 3050 a: hp deskjet 3050 has not not red print

  I recently replaced both my cartridges on my Deskjet 3050 has. He had already printed perfectly for the past 2 years.  I checked that they are correct cartridges of real HP purchased from HP.

  I'm on Macbook Pro with OS X Yosemite 10.10.5 version and wireless connection.

  Please can anyone help because it's so frustrating?

  Thanks in advance.

  Martin

  Hi Martin,

  Try to print a self-test report by selecting settings > reports > Self Test.

  You see the magenta color printed correctly by the equipment?

• Example: HP Deskjet 3050 has J11n: my printer Hp3050n used to scan to my applemac

  Until recently my HPDeskjet 3050 has scanned on my mac automatically j11n. It will not now and message scanner is not found. I am completely ignorant about computers. Help, please! Thanks.I could have disabled and now don't know how to connect.

  Hi @Valerie35,

  Welcome to the Forums of HP Support! I see that you are running into some problems of printing and scanning to your HP Deskjet 3050 has, when you try to scan, you get an error message 'not found computer '.

  If you have recently lost the connection between the printer and your network wireless, you have to reconnect using the USB key to the wireless configuration.

  Please go ahead and start troubleshooting here: printer does not maintain the wireless connection

  I hope this helps, let me know the result!

  Thank you

• Cannot get deskjet 3050 has in a j611 series print

  my printer does not print

  Hello

  Thanks for posting the question on Microsoft community forums. Looks like you can not print using HP Deskjet 3050 has.  Please answer a few questions to refine the question.

  1. do you get an error message?

  2. are you aware of changes to the computer before the show?

  3. what happens when you try to print?

  I suggest you perform the steps described in the article:

  Solve printer problems
  http://Windows.Microsoft.com/en-in/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information helps. Please reply with the status so that we can help you.

• Cannot print to Deskjet 3050 a photo

  DeskJet 3050 has with Win 7 64 bit. Computer Nonnetd to the router via the wire and the router next to the printer.

  Can not print photo via print or windows photo viewer. He said printing but the printer does nothing.

  Can print word and web pages.

  Trouble shotting attempts did not work:

  Restarted printer and PC

  Re-installed driver.

  Checked McAfee wirewall setting does not block the printer

  Need help as soon as POSSIBLE (my PC has only USB 3.0 ports with cable is out of the question)

  Looks like you may have a driver conflict.  Try a different printer driver.

  Another printer driver

  Let me know how it goes.

• HP Deskjet 3050 has All - in - One J610 series is not compatible with mac os x 10.8 mountain lion. need help.

  Hi I have a HP Deskjet 3050 all-in-One J610 Series a as indicated in the title, and I have the operating system Mac OS x 10.8 Mountain Lion. I need help to get or install the software hp for printing wireless setup in my dorm. Any help is very appreciated.

  Hello

  I'm not not clear with your exact printer model, it is the printer Deskjet 3050 a (J611) or model 3050 (J610) ?

  For the Deskjet 3050 J610- a complete software not available at this time.

  As there is no comprehensive software available for Mountain Lion, you will need to set up a temporary ad hoc connection and then use the EWS printer to connect the printer to your router.

  • Press the button on the control panel wireless to display the options menu on the screen of the printer wireless.
  • Select on the screen of the printer's wireless settings, then Netowrk default settings.
  • Under the same wireless and select Radio wireless and make sure to put it on.
  • From your Mac, click the WiFi icon and then click on join another network.
  • Click view networks, select the printer SSID, it will include 3050 or J610 in its name, then click on join.
  • Allow 2-3 minutes to establish the connection.
  • Open Safari and click on the favorite icon ().
  • Hello-click and then click on the name of the printer, the EWS page appears.
  • Enter the network tab.
  • Less wireless (802.11) click Wireless Setup Wizard and then click Start the wizard and follow the steps on the screen to configure the wireless connection.
    Note: If you must provide the type of security for your wireless network, you can click the WiFi icon, click Network Preferences and select the Wi - Fi network. Click Advanced, and you will find the type of security for your network in the Wi - Fi tab.
  • Once the wizard of wireless via the integrated Web server configuration is complete, click the Wi - Fi of your Mac and you connect to your router again.

  Finally, go to System Preferences > print & Scan and add the printer. confirm all calls to get the drivers from Apple servers

  For the Deskjet 3050 has (J611), be sure to connect the printer with a USB port and follow the installation below:
  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-107372-1&cc=us&DLC=en&LC=en&OS=219&product=5061082&sw_lang=

  Please let me know of any problems,

  Shlomi