Printer HP Deskjet 3070 all-in-One - the IP address will not save

Similar Questions

• HP Deskjet 3070 (All-in-one/Wireless) install problem Win 7 64

  Hello world

  I wonder if others have had similar problems or ideas on the underside, surely I can't be the only one to use this installation/suffering with this problem.

  Printers: HP Deskjet 3070 All in One (USB/Wifi)

  Operating systems: Windows 7 64-bit (installed absolutely fine on Win 7 32 bit laptop computer connected via wifi).

  Setup: - a Homehub BT, providing WiFi for laptop (Win7 32 bit), a desktop computer (WinXP SP3), the printer has an IP address, which is visible on the home network map - it has a MAC address also. My PC: connected by Ethernet to the homehub which is currently running wifi for all of the foregoing.

  Drivers using downloaded: -.

  + Computer laptop Win 7 32 bits connected via WiFi to the Homehub - installed fine, found printer - this is the stage where the printer receives a configuration intial IP address / completed.

  + WinXP SP3 connected through WiFi to Homhub - as above, correct, opportunity driver found the printer (which, at this time already, there).

  If the printer exists within the network, other computers can see / use it.

  ++ My PC: Win 7 64 bit connected by ETHERNET to Homehub (she does not and will not have a wireless option).

  Downloaded the drivers to install HP. (later tried "Run as Administrator"), select the software components (i.e. Remove feedback/coupons etc), installs OK applications, next step is the configuration of the printer. Add a new printer. "Check network" window appears with the message "Checking network environment" bar and the State. The status bar springs upward but stops dead at the filled Stadium. No possibility to choose whatever it, pressing Cancel has no effect. End of task here generates an error of 'work '. 'devicesetup.exe' stopped The installer never ends, applications are installed, but at no time, it shows the printer/selection.

  I tried many things: complete uninstall "engines", which in this case seem to be the only applications, ensure that all non-essential startup items are disabled, make sure that the firewall is DISABLED (just to be sure), ensure that the anti-virus is disabled there is, in fact, no other printer installed (this computer never had a printer attached to it) make sure file sharing and printing are powered, ensure that there is no TCP/IP/ports printers mapped etc... Still the same error, old or new drivers, always the same - installation does not complete.

  All the doctor diagnostic tools/printing tell me I have to install the driver software (I agree) but direct me to the HP site to download the ones I already have.

  I can't enter the Server Web integrated (the PC where I can't install the drivers, or one of the 2 PC's who have installed correctly). One of them if I click on networking or wireless or advanced it warns a HTTPS connection and then fails with "internal server error".

  My questions to someone kind enough to read this wall of text: -.

  + Anyone has any ideas please? I would prefer not to return the printer as defective because it seems to be a good all-rounder and it works for 2 other PCs in the House, its just mine which does not connect! Sad...

  I'll try the USB installation and then removing the USB-> wireless to see if that can help. I had previously seen articles where people offer to buy a router to 3rd party like that is basically a wifi pass through broadcaster. It is not for me thanks

  Thank you all for reading at least, it's now corrected with slightly reduced functionality.

  Install the USB printer, then DO NOT convert into wireless via HP drivers/installation.

  Change the USB to a TCP/IP port port newly created under the control panel of the printer (windows 7), enter the IP manually to the printer - you want an IP address that will change not in order to make this work - forcing the Home Hub to never provide that the same IP unique to this particular device was the easiest way for me. This connected but showed as offline printer constantly, others may have different experiences.

  To fix that (for me): -.

  Installing the printer in Control Panel Goto, force reinstall drivers HP ("via the drive"). Make sure that all the old files are overwritten. Turn the printer and then turn on (power button - twice if in mode "standby" to disable). Wait until the wireless light will stop flashing and become solid blue. Check in Control Panel if the status is online, if so you are good to go

  As a result of this sabotage, you lose the feature advanced scan for PC etc etc, but the real impression seems to be absolutely perfect. The printer is always available to everyone on the network, etc.

  Good luck to all.

  Alex

• My iPad and iPhone will be printed using AirPrint on my printer HP Deskjet 2540 for about 40 minutes and then will not be able to find all of the available air printers. No idea why.  The deskjet printer shows that there is a wireless connection.

  My iPad and iPhone will be printed using AirPrint on my printer HP Deskjet 2540 for about 40 minutes and then will not be able to find all of the available air printers. No idea why.  The deskjet printer shows that there is a wireless connection.

  Hi Mpsfeldt,

  Thank you for using communities Support from Apple!

  Your question, it looks like you are only able to use AirPrint sporadically. We know that situations of this kind can be frustrating, but we are here to help.

  To begin the process of solving problems, I suggest you to read about the section If you can not print on your printer AirPrint in the following article.

  On AirPrint - Apple Support

  Best!

• I tried to connect my printer HP Deskjet 2540 all-in-One Series to my Dell Inspiron 15

  Separated from this thread.

  Hi Bill,

  I tried to connect my HP Deskjet 2540 all-in-One Series printer to my Dell Inspiron 15 for two days without success.  Can you help me?

  Lenora,

  I have a HP DeskJet 2540 on my Dell Inspiron 1545.

  The instructions from HP work so you should be fine if you follow them.  The CD contains a ReadMe file that describes the installation procedure.

  You must install the software first, and only then connect the printer.  Note that you will first need to install it on a USB connection.  You can change this later if, like me, you intend to use it with WiFi.

• The cutting tool will not save anything

  Original title: Snipping Tool will not "Save as."

  The cutting tool is not going to save anything. If I press the icon Save, nothing happens and when I close and he invites me to save anything as soon as I click Yes, it just closes. I checked the registry and file my pictures, that's where it should be. I also ran some scans and nothing has come so far. Someone already had this problem before?

  Hello

  I understand the inconvenience you encountered.

  According to the description, Snipping Tool is not save something.

  I would be grateful if you can provide us with the following information to help us better understand the issue.

  1. Did you do any change important before this problem?

  2. Do you receive an error code\ error message?

  I suggest you to scan SFC and check.

  System File Checker.

  You can run the System File Checker tool and check if it helps. SFC scan will scan system files corrupted on your computer. You can read the following article to use the appropriate System File Checker tool.

  Use the System File Checker tool to repair missing or corrupted system files.

  http://support.Microsoft.com/kb/929833/en-us

  In addition, refer to the article below:

  Cutting tool

  The cutting tool: frequently asked questions

  Hope this information is useful. Please let us know if you need help with Windows.

  Thank you

• DeskJet 1510 all-in-One: the installation of the software has failed after the USB connection and remain unfinihed. Work for printer and Scanner

  My PC Dell XPS401L has been updated to Win 7 Win 10.  Then, the HP DJ1510_188 software has been installed.

  The task was ok until the bond required of the Dekjet to the USB port.

  Heard the noise of the acknowledgement of receipt, but there screen remains unchanged despite I wait several minutes. So the installation remains unfinished. However, the printer and scanner are both of the device but are not available important "Solution Center" screen.  I already have the solutions of the error indicated by HP support withot success.

  The system indicates that the problems appear in the USBsetup.exe

  Can someone help on this subject?

  Horacio

  Hi @Horacio_B,

  Thanks for joining the Forums of HP Support for a solution to your installation problem.

  I understand that you try to use an all-in-one printer HP Deskjet 1510 with a PC that has been upgraded from Windows 7 to Windows 10 but does not complete the installation of the USB and the HP Solution Center is not available. I would like to help.

  I would like to start by disconnecting the USB cable and uninstall all software related to printers. Here is a support document which can be used if necessary reference - uninstalling the software of the printer (Windows).

  Once it's over try to use the HP printer installation wizard for installation. This tool will get the software and installation help.

  Please let me know if that solves the problem, or if you need assistance.

  Indeed, if this help you to achieve a solution please click the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!

• DeskJet F2280 all-in-one with Windows 7, does not analyze, was working fine

  I have an all-in-one Deskjet F2280 my operating system is Windows 7, everything was perfectly working until recently I went to scan a document and nothing happened, the power button blinks for about 30 seconds then stops. I deleted the driver and downloaded the driver date several times but always the same problem - full while downloading I get a fatal error Code 2203, I tried the solutions proposed on the HP troubleshooting page but always end upward with the same problem. I can print & copy perfectly. Please can someone help?

  Hello swallowsretreat

  When you mention that you have tried the HP troubleshooting page you were talking about article "fatal error" error 2203' (MSI 2203) displayed for HP Software Installation in Windows? ' " Otherwise I have suggestion follows first to try to resolve the first fatal error.

  Fatal error MSI message relates to the Microsoft Software install (MSI). As such they problem may be related to more that the software you are trying to install and be linked to the operating system.

  Let me know if you continue to receive the error when installing even after the rest of the article for fatal error 2203. Also have you tried to install the printer on another computer?

• ALL-IN-ONE PHOTOSMART HP 5510 WILL NOT PRINT AFTER GO 'SLEEP' MODE

  My printer model:

  HP PHOTOSMART ALL-IN-ONE 5510 B111A

  Problem:

  Printer goes into sleep mode. After 25-30 minutes breaks the connection between the PC and the printer wireless. Beacon wireless is the same fashionable "sleep" and I see that the printer is connected to my router and there is internet connection. HP Print and Scan doctor sees the printer, but I can't wake the printer unless I restart it.

  What I've tried so far:

  I tried all the solutions offered hp.com; Reinstall driver, updating the printer software, setting static IP on the printer, static DNS servers, using HP print and Scan doctor.

  I've seen people questioned on this issue before and there is no solution. I really need help from HP!

  After days of research, the problem was finally solved! I applied the following steps below. Some steps may be unnecessary, I didn't waste my time knowing who.

  1. find your PC's DNS servers by typing ipconfig/all in CMD.
  2. assign a static IP address outside your DHCP range. For my Linksys router him between 192.168.1.100 to 192.168.1.150. So I put my static IP address as 192.168.1.20.

  To do this, click the button on your printer wireless. This will show the IP address of your printer. This type of your browser. Go/network/network address. Choose manual IP and write 192.168.1.20

  3 now come to section of the manual DNS server, and then type your DNS servers, you found before.

  4. open your HP printer program that must be installed with your driver. Utilities hit and update the IP address. Update your address with your static IP address.

  5. now go to your router settings. Find the wireless settings and change your not automatic standard 20 MHz radio band.

  6. change your standard channel to 6.

  7 find the wireless security and replace your WPA-personal security mode.

  8 disable UPnP

  9. This is the part of the KEY. Change the renewal of your key to 36000 seconds. (10 hours)

  10 go to the Windows Advanced Firewall. Enable all the disabled printer and share, entrants and outbond rules.
  I believe that the most important parts are affecting a static IP address outside your DHCP-range and change the key renewal time. I hope this works for you too

• L7580: HP All In One L7580 - Scans but will not print or copy

  Last problem with the L7580: this machine will scan but not print or copy.  All four color cartridges are good, remaining.  He machine is not used as often as it should be, but copied and printed a few weeks ago.  Any suggestions?  Thanks for any help.

  Hi @kkpb,

  Welcome to the Forums of HP Support!

• OfficeJet Pro 6978 all-in-one: OfficeJet Pro 6978 / will not download drivers

  I just bought this printer Office Jet Pro 6978, All In One Printer.  It won't let me download the driver listed in the steps to implement, it fails every time.  I tried to use the CD that came with it, it gave me a message "this computer's operating system is not supported."   So this printer will not work on my 64-bit?  Or elsewhere?  My computer is a HP.  Where can I find a download driver for this printer for my operating system?  When it prints, it prints a nonsense.  % beginprolog % beginresource: file and so on with such things.  I am at a loss... Any help would be great.

  Hello

  Sorry, but the printer is not supported on Windows Vista 64-bit.

  64-bit support is only available in Windows 7 or later operating systems.

  You can find the printer specs below:

  Vista 64-bit is not supported.

  http://support.HP.com/us-en/product/HP-OfficeJet-Pro-6970-all-in-one-printer-series/8289585/model/11161264/document/c05061732/

  You must upgrade your operating system to a later version to use instead an OS 64 - bit, Windows Vista 32 - bit to insall or replace it with another printer, compatible with your operating system.

  Respect,

  Shlomi

• How to open the queue for the printer HP Deskjet F2120 all-in-one printing?

  My OS is Windows 7 Home Premium. I had a problem with being stuck in the print queue, print jobs what has caused the printer become inoperative.

  The print queue is now disabled, but I had to download a diagnostic tool from HP which has scanned the printer and cleared the queue. That fixed the problem, but in the past when I had this same problem, I just access the leading printing and deleted stuck jobs. I couldn't find a way to get to the queue print this time and I hope someone out there can tell me what I did right.

  Hello

  • Click Start
  • Click on devices and printers
  • Right-click your printer and choose "see what's printing.

  Tricky

• software and star driver hp psc 1315xi all-in-One extracts full but will not load on xp sp3

  Can not find a way to get this to install. After extracting I finally found it in running %Temp%. Searching through all files and folders, trying to find the exe file. to get it to autorun, but was unsuccessful. I tried to install this on 2 different PC with xp pro sp3 but no luck.

  The solution below is from michael323 here in the Forums of HP's Support.  Make sure that you send Bravo!

  I think I have solved this problem.

  I have a PC Windows XP Pro (SP3) who has been affected by this problem.

  Immediately after that the window of 'extraction' went to 100% and closed, nothing happened.  The windows install/never display software.

  Whenever I tried it creates a log file that started with this:

  "Parsed command line: «.\Setup.exe".

  Using datfile: C:\DOCUME~1\xxxxx\LOCALS~1\Temp\7zS1293\autorun.inf

  # GetValueByLang (f-> c_str(), _T (Version), _T (LanguagesInthisCD) failed "

  System LangID = 1033.  mapped to ENU

  # The system language is ENU, but is not on our CD!

  There was other error messages after that, but they all come from lines 3 and 5.

  Something she prevented the installation program to recognize the language ENU files ARE present in this download.

  Comparing two PCs, a problem, and one that works perfectly, I saw that one who was not was AutoRun disabled through a registry setting.  I temporarily deleted this registry on the PC that wasn't and Setup launched and ran like he was supposed to.  Here are the first of this log from the same PC, a few minutes later, where the only difference was that I had removed the registry setting criminalized:

  "Parsed command line: «.\Setup.exe".

  Using datfile: C:\DOCUME~1\xxxxx\LOCALS~1\Temp\7zS1293\autorun.inf

  System LangID = 1033.  mapped to ENU

  We use the system of language = FRA, which is located on our CD!

  As you can see, the message "(LanguagesInthisCD) failed" (line 3) disappeared, and the line 5 (now line 4) shows that it has to recognize that the language ENU installation files are present.

  So if you encounter this problem, and you are comfortable with the system registry, here is how I got it to work on my PC:

  Start regedit
  Navigate to the bottom of this tree
  -HKEY_LOCAL_MACHINE
  -SOFTWARE
  -Microsoft
  -Windows NT
  -CurrentVersion
  -IniFileMapping
  Below, find out if there is a key named "Autorun.inf".
  On my PC (the one with this problem) the value of this key has been "@SYS: nexistepas".
  If your registry database also has this, it may be the cause of your problem.
  In the left pane of regedit, do a right click on Autorun.inf and select "Rename" from the context menu.
  Change the name to something like "Autorun.inf.hold".
  Close regedit
  At this point, I restarted my PC, but I don't know if it is really necessary.
  I ran the downloaded driver file.  It extracted, and the Installer started out as it was supposed to.

  When it was done, I returned in regedit and renamed "Autorun.inf.hold" to "Autorun.inf".

  It is extremely frustrating for me, and (if you need it), I hope that this solution works for you.

• HP PSC 2355 all-in-one: HP PSC 2355 will not recognize Windows Vista Home Basic

  I bought this product in 2005. I'm just out of the box yesterday. The printer works fine. The software CD was made before Windows Vista Home Basic Edition. He acknowledges only 98, Me, 2000 and XP. He calls a Unknown600 to Vista. Is there a driver or other update I can use? Thank you.

  Hi @Mc_Cool,

  Welcome to the HP Forums!

  I noticed that you are looking for a basic Windows Vista Home Edition driver for your HP PSC 2355. I'm happy to help you!

  You can download the driver directly using this link, HP full feature software and drivers.

  Hope this is what you are looking for and have a great day!

  "Please click the Thumbs up icon below to thank me for having responded."

• Two BIG problems: Firefox clears the tabs and will not save preferences

  Long story:
  I'm on a 2009 15 "Macbook Pro Intel Core 2 Duo with OS X 10.6.8. A few weeks ago I started suddenly problems with some features in Gmail... but only in Firefox. Specifically, I was no longer able to preview attachments in the new Gmail attachment viewer. After a long back-and-forth on the Gmail forum with no results, I turned to Firefox. After having poking around in Firefox Help, I decided to reset Firefox. This solved the problem with Gmail, but in turn created two new more serious problems with Firefox: (1) I can't save my history settings in the privacy of the preferences tab (I want to use the custom settings; whenever I have this option in the menu drop down and close prefs., as soon as I open Pref once again, the history of setting is default return "remember history"; (2) even more serious and obviously related: whenever I quit Firefox, all my tabs and groups of tabs went to the re-opening. I can restore the previous session, but this obviously isn't the solution.

  I basically tried everything suggested in the articles referred to in the help of Firefox, reset Firefox again, trashing the prefs.js file in my profile folder (I have no other pref files - that is to say without "prefs - n.js or 'prefs.js.moztmp' or 'Invalidprefs.js'... I don't see not a user.js file in my profile folder either). I even used the disk utility to repair permissions on my Mac HD... for all that is worth it.

  I'm so sick of everything that I am seriously considering ditching Firefox altogether. There, can someone help me understand what is happening?

  Accidemic13

  Choose "Use the custom settings for history" allows you to see current history and cookies settings, but select this is not make changes to the parameters of the history and cookies.

  Firefox displays "Use the custom settings for history" as an indication that at least one story and cookie settings is not the default to make you aware that the changes have been made.

  If all the parameters of the history and cookies are by default, the custom settings are hidden and see you "conservation rules: (never) don't forget history."

• has got HP Photosmart C4180.when I scan more than 1 page of the document, it will not save pages as 1 file

  I have HP Photosmart C4180 printer and when I scan 1 page of a document, it will save all the pages into a single file? I wonder why?

  ozzyuk,

  Thanks for the information. I would like you to go ahead and start here: how Scan: Windows 7, remember that you must have the full feature software and drivers installed and use the HP Solution Center. Once on this page, please select the way to scan with HP software and select the multi documents page.

  I hope this helps!

  Thanks again,