Pro M30 satellite cpu fan works not

on two occasions, I replaced a system on a satellite pro m30 card so that the cpu cooling fan no longer works. This is the case even after recovering the OS from the disk.

is there any other known this.

I talked to others who say that I need to improve the DMI

any help please

Hello

Well, I put t know if the DMI update will solve it, but as far as I know the service partner should upgrade the DMI. After the replacement of the motherboard it is also important to start the diagnostic program and special test, because without this procedure, the CPU can t works with a maximum return. This can be done by the service partner. The update of the BIOS is also a possibility

Tags: Toshiba

Similar Questions

  • «the cpu fan works not.» Check the fan connections and call for service. »

    I was wondering if a failure of different from 'CPU fan has failed... system in a few seconds will stop. " I have an office of DX - 2000 P4 under XP SP3 that I just changed the motherboard and CPU fan on. All the fans are running at about the same speed. (P/S, chassis and CPU). Not very fast but cannot see the fins. Computer sat for several years. I was wondering what is the real test and how the fan speed is controlled. I suppose that temperature sensors built into the cpu, somehow, there must be a variable voltage applied to the fans to change their speed and/or a measuring device to see what is their RPM. This must be controlled by the BIOS as is any pass/fail test. My next step is to replace the old fan and see what happens. I have a new p/s to install should be here today. Actually used, but cleaned up and tested. Economy of cleanup. Not sure if my older diet could be the cause of the issue with low Volt.

    If the fan is slower than the factory fan, you will have this problem.

  • Satellite A10 S203: the CPU fan does not work properly?

    I have toshiba satellite a10 s203 and the cpu fan does not work correctly. What can I do about it?

    Hi SACRIFICE them.

    Here are some possible solutions to this problem of fan.

    1. When you have installed a base installation of MS (not the Toshiba Recovery CD) you need to install the Toshiba Power Saver and others utilities from the CD tools & utilities. The energy saver is responsible for the control of the fan.

    2. If you have a recovery based OS, you can update the energy saver of http://eu.computers.toshiba-europe.com site Web Toshiba under Support & Downloads - Download Driver

    If please check this and an answer then follow the next step!

    CAMPino

  • The CPU fan does not work on Satellite A60

    Hello world

    I have a little problem with my laptop.
    I noticed my cpu fan does not work. only the second fan are working fine. (general fan)

    my PC is a satellite A60
    You have a solution to find why my fan does not work?
    THX

    Hello

    I put t know what fan you mean because I saw only a single fan at the bottom of the unit. However, perhaps the second fan is hidden.
    It's not easy to say why the fan doesn't work. Maybe dust clog up the fan and cooling module may not work correctly. You can try to use the vacuum cleaner to clean the fan.
    If it doesn t work so I guess there must be something wrong with the material and to fix this, replace this part. But in this case I recommend to contact the after-sales Service of Toshiba partner. He has much more experience in such cases.

  • Dell Inspiron N5110 CPU fan does not work

    Hello world

    I have a problem with a DELL Inspiron N5110.

    When I turn on the laptop, the fan runs for 15 seconds then it turns off by itself... but the Windows starts correctly, and other components work fine.

    I know that I can't use my laptop if the CPU fan does not work because it will overheat the cpu and the motherboard so...

    Could you please give me an advice?

    Thank you

    The fan will run at powerup self test time, and then won't turn on (or run at full speed) up to a set temperature is reached.

    Function that replaces the motherboard, check that the thermal pads have been replaced when the radiator has been removed from the system.  If this part was not replaced, the system will run very hot.

  • Satellite Pro L40 PSL4BE starts no - HDD + CPU fan is not

    Hello

    I own a Satellite Pro L40 - 17F (PSL4BE-00R005EN).
    I've been running the system on the current for a while now.
    I decided to remove the battery to avoid damage.
    Last night, I accidentally pulled the addapter at the back of the laptop. Since then; the machine won't start.

    I noticed that the HARD drive was not making the usual noises. Then I realized was not the CPU fan is spinning.
    Nothing appears on the screen, not even the start menu.

    The only things that do not seem to work are the DVD player & power light!
    I had the back of the machine off; I didn't see any obvious reason for the problem.

    I'm looking for a second opinion on what is happening with it, and if it can be fixed without having to buy a new motherboard.

    Thank you. Dan.

    Hmm. possibly, there is nothing wrong with your motherboard.
    Try this common workaround that has helped me in such cases.

    Remove the battery and unplug the AC adapter. Leave the laptop for about 30 min and after this short break, put the battery in the laptop and connects to the AC adapter.

    This short procedure helped me to sort a similar g and strange question.

    I hope that you will succeed if you please post some results.

  • Satellite Pro M30 Win 7 - webcam does not work on msn messenger

    Hi all

    I have a Satellite Pro M30 Modell Nr.: PSM35E and just changed to Windows 7. But put him Nvidia card NVIDIA GeForceTM FX Go5200 Grafik 64 MB of RAM is not working properly.

    I could find a Vista driver and installed, have Aero + photos on the desktop, but my webcam does not work on msn messenger and this is the only way for me to see my family.

    Can someone help me?

    Thanks for your help

    Hello

    I m a bit confused; you have some problems with the graphics card or with the webcam?

    I assume you mean on external webcam connected to the USB port? Right?
    What happens if you connect the webcam to the laptop? Can win 7 recognize the device? Have you installed additional drivers for this webcam?
    Most of the time it s necessary to do so because I think that it s not Plug & Play device.

  • Re: Satellite A300 - fan does not work after installing Win7

    Hello.

    I did a new install of Win 7 pro 64-bit, and after it does not my fan, not at the start or in Windows. To check if it the fan itself was broken I re-installed Vista instead and the fan worked again!
    Installed new Win 7 but now it's silent :( I checked in the BIOS (latest version 1.80) but I couldn't find any option here. Am I missing a driver or something?

    My Satellite canned extinguishing because of this, so I would really appreciate help :)

    Best regards / Ocke

    Post edited by: Ocke

    Hmmmm... really strange. I use Win7 32 bit on my Satellite A300-1LI and it works perfectly.
    Maybe a stupid question now, but have you tried to use the 32 bit version?

    You have also installed all the Toshiba drivers Toshiba value added package (includes the Toshiba power saver tool)?

  • Satellite M30: cold - no fan work

    Hello, I used my recovery Cd, and since then my satellite is not cool. I don't hear the fan operation. What should I do?

    Hello

    The fans do not work or you do not hear only fans work?
    If the cooling module works not the CPU can damage.
    In this case, you should not work on the laptop if the CPU can't be cool and you should contact Toshiba service partner in your country for the control of the laptop.

  • Satellite P100 - 387 CPU fan works like crazy

    Hi all
    I have a laptop Toshiba Satellite P100-387. I bought it with 2 friends. The same model.

    The problem exists only in 2 of the 3 laptops. It looks like this. When I start the machine everything is ok. While windows starts cpu cooler (or video card cooler if it exists) starts to work. If the fan starts to work the low speed at the highest. And did it for 5 - 10 times. Then a few minutes break and again. It's really noisy. It seems that when you insert a CD or a DVD.

    It goes like this also when windows is started. No high consumption of CPU, the fan works like crazy. Start at full speed for 2-3 seconds, then for 1 second and still the same.

    Everyone has the same 'characteristic '?
    What is this Toshiba Power Saver software works with p100-387?

    Hello

    I P100-109 close to me and I noticed the same thing. There is no difference between preinstalled WXP or Vista and because of this, I assume that this is a normal behavior. I know it's sometimes troubling, but unfortunately you have to live with it.

  • I can check a message that my CPU fan is not working?

    A few days ago I got a message that my CPU cooling fan not working properly and I should check it out. but the next time I logged in that I have no message of second check of my first message. I can interogate my computer to check the first message and if so, how?

    Hi DavidDudley,

    You may need to contact the manufacturer of the system or consult the manual supplied with the computer to test if the CPU (central processing unit) cooling fan does not work correctly or not.

  • Satellite A200 - fan works too

    Hello

    I will present my problem briefly to you in the hope that I can find a solution.

    I work with recording music. My Satellite A200 can handle the processor high and all the rest. I'm really very happy.

    But the fan works just too well even when CPU is not used much. I installed The Ultimate Troubleshooter (excellent software) in order to eliminate unnecessary software or process. My RAM is 73% free, low 0-10% CPU and my fan speed is measured at 47 degrees Celsius. My hard drive is 33 degrees Celsius. Very low.

    The boring bit, is that my fan is behaving intermittently, but even when nothing is really happening, and the temperature is still very low. I have another laptop to compare to, which is quiet and peaceful in the other corner of the room and only takes action when I activate several operations at once. I wish my Satellite to behave in a similar way.

    I cleaned the fans today, and a lot of dust came out. But still the fan curve. I tried to take control using SpeedFan 4.43, but it does not work. I don't see anywhere in the BIOS how I could control the speed of the fan.

    I need to find a solution, ideally one that doesn't involve buying a new fan, or disassemble the computer. Since the temperature is right at all times, I guess it's just the BIOS programming for constant speed activity that must change. Any suggestions? It would be appreciated.

    All the best, Shlomi.

    Hi shlumaan_1,

    > I cleaned the fans today
    How did you do that? Did you follow the instructions?
    How to clean a Toshiba laptop cooling system?

    There are different reasons for activity high fan and dust that blocks the fan, the thermal paste should be renewed, etc..

    Fact is that the fan will be controlled automatically to protect the equipment from overheating. What you can do is chancing the cooling method in Windows power management. I put t know what operating system you use but on Vista and Windows 7, open the power management options, change the parameters of the plan, cooling method. You can change between maximum performance and battery optimized. I would recommend setting the optimised battery.

    Also, check the BIOS version. If you have an older version, probably thermal management has been changed with a new version of the BIOS. Update the BIOS that you find on the official website of Toshiba.

    Finally, and especially if your laptop probably has a few years, that the thermal compound must be renewed. This is why I would contact an authorized service provider that will apply the correct thermal grease and also the laptop must be disassembled. Not so easy

  • Satellite A500D - fan does not stop

    Hello

    Two days ago I updated the Bios to version 1.20 win, and since then, the fan is constantly at 72% and the temperature of the CPU at 36 º.

    At Toshiba, I say it is normal, but the fan does not stop at any time and the noise is annoying.

    Anteriormento updated the BIOS, the fan stopped and started and never surpassed 54%.

    Looks like a vergueza by the care service, they have given me, I tried to deceive, as is normal for a portable fan that keeps 72%.

    Please I need someone to tell me where I can download before my Bios and how to install it.

    PS: My processor ens Turion Rm-77.

    A welcome message

    Hello

    You mean the cooling module fan didn't run all the time with the previous BIOS version?

    Well, in this case you must downgrade BIOS to the previous version.
    The problem is that you can download the latest version of the BIOS from the Toshiba page.

    But maybe a Toshiba ASP might help you and may downgrade the BIOS to the previous version

    But have you tried to change the settings in Win 7 power option?
    You can find it in the control panel-> power options

    There you can change modes of single power supply.
    In the power settings advanced, you'll find settings Toshiba energy saver and there you can change the method of cooling while the laptop is running on battery or power.

  • Satellite L20 fan does not stop

    Hello!

    I have a problem with my Toshiba laptop fan:

    It starts to spin and cools the system but doesn't stop until I stop the system and restart.
    The temperature is 37 ° C at the disk and 47 ° C for the CPU.
    I have no idea why the fan stops not more and its very annoying...

    Thank you for your answers

    Hello

    You have installed the Toshiba power saver on your device? Generally, all Toshiba laptops preinstalled energy saver. This program is responsible for the performance of the processor and the fan. You must enter the energy saver and check settings that control the cooling.

  • IdeaPad Y570 fan works not properly

    Hello

    The fan on my IdeaPad Y570 suddenly stopped marketing. It does not spin regardless of the temperature, and therefore, the temperatures reach 90 C +. Mode of dust collection works very well, the fan turns as expected for the cycle and seems normal. If the fan is not physically broken or clogged. I also installed 3rd party software CPUID HWMonitor to check if temperature sensors work, and they all show temperatures at levels expected and more than high enough to warrant coming fan.

    I don't think that I have installed a new software that might interfere with it. I tried to reinstall the Lenovo Energy Management software, but that did not help. I also tried from the laptop in safe mode, without result.

    Thanks in advance for any help you can provide.

    HWMonitor screenshot:

    Applied Windows updates and this problem is solved. Hope this helps others in the future.

Maybe you are looking for

  • Satellite Pro M30: Where to find the Vista drivers?

    Hello everyone, Please I need to know how to find toshiba updates drivers for windows Vista, my computer model is Satellite Pro M30. Please guys, I found it very difficult to not be updated. I've already updated my Rams to 1 GB. PS: It is a sequel to

  • Skype for web has local storage?

    Hello I have to answer this question and didn't know what to say. Maybe someone knows if Skype for web stores offline conversations, or updates the server all the time?

  • Satellite Pro A100 - cannot update driver ATI

    Hello! I have a problem with my graphics ATI Mobility Radeon x 1600 card card. I can't update to the latest driver from the ATI. The program says that it can not install on my system - contact company for the most recent driver. But the one that is p

  • Recent firmware for R8500 translates into automatic channel permanent 2.4 GHz

    After update to the last couple of updates of firmware, for example 1.0.2.64, 2, 4 GHz does not accept the selection of channel 1, 6 or 11. Instead, a wifi scan will show something random like 4 or 7 transmitting it as in mode auto-canal, in contradi

  • How to add the external library in NDK?

    Hello! I have problems adding the libhuapi library. It is not available in the Add Library Wizard. And if the libhuapi.so file is added as an external lib newspapers of the device: Unknown symbol: hu_ECDSAWAPINoHashVerify Unknown symbol: hu_ECDSAWAPI