problem by ejecting the modem

Similar Questions

• Problem: Error 633: the modem (or other connecting device) is already in use or is not configured correctly.

  While I am connected to internet using Reliance Netconnect Huawei 1260, the connection disconnects after 10 to 15 minutes. Shows as connected Netconnect but does not work. I try to disconnect the connection, but it gives an error.

  Reconnect to always remove the modem and then re - login again.

  Please provede me a permanent solution to this. I use Windows 7 Enterprise

  Hello

  1. If it works well before?

  2. what version of Modem drivers do you use? Do you have any other device connected to the computer?

  First of all, I suggest you to check if the modem is compatible with Windows 7.

  Check out the link:

  Windows 7 Compatibility Center:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  I would also recommend to connect the modem to a different computer and check if it detects there. If it does not work on another computer also, then the problem is with the modem and I would ask you to contact the manufacturer of the modem for any further assistance.

  Error 633 indicates that the port is already in use or is not configured for remote access dial out. You may need to check if the VPN and the connection connection try to use the same port that is causing the problem. You may need to check the settings of the modem and change the port for your needs.

  To work around this problem, use one of the following methods:

  Method 1:

  Reserves explicitly the TCP port that is used for the VPN connection. To do this, follow these steps:

  a. click Start, click run, type regedit.exe in the Open box and then click OK.

  b. in the registry editor, find and then click the following registry subkey:

  HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Tcpip\Parameters

  (c) in the Edit menu, point tonewand then click multi-string value.

  d. rename the multi-string value as 'ReservedPorts' and then double-clickReservedPorts.

  e. in the value data box, type1723-1723, and then click OK.

  f. exit the registry editor.

  Registry warning: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://support.microsoft.com/kb/322756/

  .

  Method 2:

  Use the netstat command to find the program that is using port 1723. Then, end the process for this program. To do this, follow these steps:

  a. click Start, click run, type cmd.exe in the Open box and then click OK.

  b. at the command prompt, type the following command and press ENTER:

  NETSTAT - aon

  c. in the result which appears, identify the process ID for the program, if any, who is using the TCP port 1723.

  d. at the command prompt, type the following command and press ENTER:taskkill/pid PID/f

  Note: The taskkill command terminates the process that corresponds to the ID of the process. The/F option is used forcefully to complete the process.

  e. at the command prompt, typeexitand press ENTER to quit the command prompt.

  Restart your computer. This may cause the program that uses the TCP 1723 port to use a different port.

  I hope that helps!

• Error 633: The Modem already in use or not configured properly

  Hello

  I use a Windows7 Home Premium 64 bit PC.
  When I am trying to connect to the internet via 3 g USB modem, I get error 633: Modem is in use or not properly configured.
  The software and drivers have been installed correctly.  I uninstalled and re installed several times without success. I tried the same thing in safe mode without success.

  Any help is appreciated.
  Thank you

  Hello

  I suggest you to check if the modem is compatible with Windows 7.

  Check out the link:

  Windows 7 Compatibility Center:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  I would also recommend to connect the modem to a different computer and check if it detects there. If it does not work on another computer also, then the problem is with the modem and I would ask you to contact the manufacturer of the modem for any further assistance.

• Problem with TC loss of connection to the modem cable

  I have a TC of 2 TB which is connected to my ISP provided by cable modem. It worked fine for 3 months after the installation in December, but now all of a sudden it will lose its connection to the modem and we lose our wireless internet. We have replaced the modem cable and it does not solve the problem. I have to reset the TC 2 - 3 times a day. Nothing else has changed recently with regard to the network set up. that only changes were to specific devices that use the wifi connection, and this was always something changing, depending on the devices we use. Any thoughts? I'm not a savvy person tech, BTW.

  We need to ask a few questions in order to learn more on what the possible cause of the problem might be.  Please be patient with this. Thank you.

  What is the number and the model of the modem you are using right now?  We ask because some modems work better than others with Apple routers, and even if you have changed the modem, it could still be a model who does not get along well with the Apple router... or... you could say that the router from Apple does not get along well with the modem.

  How old is the TC? We ask because the life expectancy, on average, a time capsule is about 3 years.  After that, they tend to start losing connections to an ever-increasing rate.

  Who is your provider of Internet (ISP) Service?  We ask because most suppliers are in the active process of implementation of a new type of connection called IPv6 in their systems... and despite ISPS claiming that their system changes should cause no difficulties connection or interruptions system... which doesn't seem to be the case at all.

  We have seen an unusual number of reports from users who suddenly have problems with their ISP connection, when things were very well for many months before. That points directly to the IPv6 changes that ISPS are doing as the culprit. In some cases, there could be way to work around the problem, and in some cases, there is nothing to do but wait as the ISP to complete their changes and be everything to speed.

• Sound problems and the modem EA60-155

  3 weeks ago I received my laptop EA60-155 and have experienced ongoing problems with the sound and modem on the laptop. I bought the laptop from currys so am sure that they are an authorized dealer.

  The problem is different, sometimes I turn on the laptop to find out, there is no sond and the modem does not work, sometimes the sound works and makes the modem for about 15 minutes before the problem arises again. I bought the machine to the dealer authorized to Bahrain twice now, twice they said them that the problem was resolved when he doesn't. I called the center of appeal twice, but I still have the problem. Any advice would be greatly appretiated.

  Hello

  If you have this problem permanently, you can try to reinstall the modem and sound card. If the unit is pre-installed with recovery DVDs, it should work fine. As a first step, you can try and remove the sound card and the modem from Device Manager, then restart the device. The two hardware components must be recognized and installed again.

  If there is no success I recommend you backup your data and reinstall the OS using recovery DVDs. On this way the unit will be clean installed and there should not be any problem. Every problem that happens after that can be some hardware malfunction and you must contact the Service partner again.

  Good luck!

• Problems with the modem Toshiba G450

  Hello

  We faced a problem. We have installed a software and drivers of Toshiba g450 on different laptops to use it as a modem for a mobile phone network. When we have logged in as administrators all fine, when we have logged on as a normal user in the field, the software will search the modem without success. We do not have such a problem with other USB modems.

  Thank you

  André

  Sorry Andrew, but this forum is explicitly designed to discuss with the portable mobile computer.
  G450 laptop, desktop, PDA, or cell phone is?

• Problems with the modem with XP Pro

  I upgraded to XP Pro and cannot create a dial-up connection because this option is not available for me. I checked the Microsoft support pages and enabled dial-up as suggested by using regedit.
  Still no difference. So I guess that the modem or the modem settings are the problem.

  In Control Panel, if I go to phone options and modem, I see "Toshiba Software modem AMR COM4" but, if I go into the settings of the Modem in Control Panel, I get the message that the modem is not installed correctly and I have to uninstall and reinstall. I did this several times without success.

  He drives me crazy - can anyone help?

  Hey,.

  What operating system you have, what is the model of the computer?

• Anyone having problems with the modem from Cox and Time Capsule

  Hello

  Lately my internet falls down every day or every two days with Cox. I have reset the modem, the time capsule, the routers extreme apple, etc. shut down and restart my whole network. I called Cox every two days to refresh the modem.

  I heard that I may need to reconfigure my Time Capsule (acts as a router) to avoid this problem.

  No one knows what to do here?

  Thank you

  Please, try the following:

  Open the AirPort on your Mac utility (Finder > Applications > utilities > AirPort Utility)

  Click on the image of the time Capsule

  Click on edit in the window that appears

  Click on the Internet tab at the top of the next window

  Click the Internet Options button at the bottom of the window

  Make sure that the IPv6 configuration is set to Local link only

  Click on save, if you make changes, then click Update at the bottom right of the window

  When Cox fully implements IPv6 (they are not), you may be able to return to the automatic configuration.

• Satellite A200 - 13 M - XP x 64 - problems with the modem drivers and webcam

  Hello!
  I recently installed Windows XP x 64 on my laptop.
  I have two devices that do not work properly.

  (1) does anyone know how to get the driver for the built-in modem? There is no version the x 64 required for download.

  (2) the webcam does not work. I had a problem of 'Windows Image Acquisition': error telling me to put this service to activate the webcam. The problem is that this service is, by default, already activated.

  Thank you for your help.

  Hello

  You are right. 64-bit drivers are not available. Unfortunately, 64-bit version is not supported. To be honest, I'm sure that the modem is not so important for you and you can turn off this feature.

  I can't say much because I use the 32-bit operating system only on webcam.

• BEFSR41 Ver 3 connection to the modem Motorola 2210 problem

  I have a simple (I hope) home office network configuration.  I have a router Linksys BEFSR41 Ver 3, a Vonage phone device, a couple of computers and printers all hooked into the router.  The problem appeared when my old modem is dead.  I replaced the old modem with the Motorola 2210 (from AT & T) and configure the modem, so now the internet works if I plug the line directly into my computer.  When I try to run it through the Linksys router, the signal comes through.  I've turned off and rebooted twice and the second time I did it in a particular order, but still no signal through the router.

  I see that the IP address of the router is 192.168.1.1 and 192.168.1.254 is the modem.  It seems that something needs to be reset somewhere, but since I'm no computer, I don't know what to reset where...  I read the other posts and they speak to reset a PPPoE on the BEF, but where do you do that?  And is there something different about my router 3 worm?    Any help is appreciated... I'm pretty frustrated and miss me phone calls from my device Vonage is not connected...

  Thank you very much in advance...

  Leslie

  You the problem is that you try to use the same subnet 192.168.1.x into the WAN (Internet) port and the LAN of your BEFSR41 ports.  You can't do that.

  Your modem is apparently made your PPPoE connection for you.  So you should NOT repeat this PPPoE connection in the BEFSR41.

  Setting network, follow these steps:

  (1) put your entire network.

  (2) disconnect all other devices BEFSR41.

  (3) connect your computer to one of the four ports LAN on the BEFSR41.

  (4) turn on the BEFSR41 and your computer.

  (5) point your browser to 192.168.1.1 and connect to your BEFSR41.

  (6) change the "Internet Connection Type" to «DHCP - auto»

  (7) change "local IP address" 192.168.2.1

  8) click the 'Save Settings' button, and then wait the screen refresh (3-60 seconds).  You will be disconnected from the BEFSR41.  Don't worry about this.

  (9) turn off the BEFSR41 and your computer.

  (10) wire the ethernet port of your modem to the Internet (WAN) on the BEFSR41 port.  Leave your computer connected to the BEFSR41.

  (11) power of your network.  It should work.

  BEFSR41 using you now on its LAN ports 192.168.2.x subnet.  You can now connect to the BEFSR41 facility to 192.168.2.1

• INTERNET CONNECTION PROBLEM - laptop computer connects is the DNS through the modem to broadband gateway to resolve the address of Web site

  Regardless of the browser that I use on my VISTA laptop, navigation stops... which means the laptop connects is no longer the DNS through the modem to broadband gateway to resolve the address of the Web site.

  However internet is on and some applications that Act on the internet are connected and okay. for example: Skype

  Hello

  Try this process.

  WinSock and TCP/IP

  When parasites get installed on your computer, they might create hooks in the system computer activities related to the program "Junk" files  When you get rid of the 'Junk' hooks could remain in the system, in the absence of target files (they cleaned) problems are created in the network and Internet related activities.

  If after uninstalling the "Junk", the Internet connection does not work as it should, you will need to restart the operating system parts which get trashed by the process.

  WinSock and TCP/IP update.

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  Do the same process to refresh the TCP/IP just replace the command typed with.

  netsh int reset

  And the sam to do this.

  ipconfig/flushdns

  Restart your computer.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Connectivity problem - problem with the modem or the router of network

  I had a network with 2 computers.  The main computer was a Windows XP operating system and the secondary is a Windows Vista operating system.  There was a modem connection and the router. Due to a storm and a leak in my ceiling in my main computer got wet and I couldn't use it.  I have connected the modem without the router directly to the secondary computer, but it is not recognize the modem.  "Internet Explorer cannot display the webpage." So I ran the diagnostics and received a message that there could be a problem with the modem or the network router.  I did the thing 'ipconfig' and there is no gateway.  Is there anything I should do to make this secondary computer main computer?

  Hello

  If you use a router there is no primary and secondary, all the computers connected to the router are equal.

  Many Internet service providers allow you to control some form of autehtication (ID, PW) online journal.

  Your router and the computer humid probably were installed to authenticate.

  If the router does not use it.

  Otherwise, contact your ISP and ask for the help of authentication.

  Jack MVP-networking. EZLAN.NET

• Windows removes the internet conntction system. Connected directly to the modem. Have tried to go through just wifi. the same problem. Only happened for several weeks.

  Windows deletes internet conntction after a few minutes. The netgear and control panel says I'm always connected. Must reboot to get reconnected to the windows system. Connected directly to the modem. Have tried to go through just wifi. The same problem. Only happened for several weeks.

  Hi Sailortdt,

  Welcome to Microsoft Community where you can find the answers related to Windows.

  According to the description, it looks like you are facing a problem with network connectivity.

  It would be awesome if you could answers to these questions in order to help you further.

  1. have you made changes on the computer before this problem?

  2. you receive an error message or error code?

  I suggest you to see the steps in the following Microsoft article and check if it helps.

  Problems in Windows wireless and wired network connection: http://windows.microsoft.com/en-US/windows/help/wired-and-wireless-network-connection-problems-in-windows

  If you need Windows guru, do not hesitate to post your questions and we will be happy to help you.

• Problem with the Modem devices: Modem already used or not properly configured

  I use windows 8. Until last night, my laptop was working fine, but now it rejects all the modem devices, I try to plug it. I tried to connect to internet via Auntie photon and reliance netconnect +, but this message "Modem already in use or not properly configured" keeps on appearing two modem devices? Is there a problem with my OS or my laptop? Help, please

  Thanks for the solution.
  Well, my problem was similar but different too. The method to uninstall the modem device is correct. I tried, but still it did not work.
  My problem was that I have 3 different modems installed on my pc, but I used one of them. So I would uninstall only one I used. It turns out that we have to uninstall all modems. Its pretty simple, but its not so obvious. I thought about it later in like 2 days. I hope that people reading this don't have to wait 2 days to fix this problem.

• Problems with the modem on L40 (Vista)

  Hi guys,.

  I am trying to help a friend out with his new laptop computer, as she dosen't have DSL and needs must use dial-up. I'm new to Vista so please tell me if I'm missing something obvious.

  Right... I use the same cable modem and telephone line that also works on another PC, and before ask you I pluged it in the modem port and not the ethernet port. I can query the modem ok by Device Manager / modem properties. I noticed that the modem is configured for some software of Toshiba and not a comm port, is this correct? When you look at the software Toshiba itself it looks like the comm3

  When I try to create a dial-up connection / use dialer I get the error that it cannot get dial tone, I also tried to change the setting so that he always tries to dial without tone, nothing helps. If it works on another PC ok, I'd say it was the cable modem or phone line.

  Any ideas?

  See you soon

  Hello

  Are you if that cell phone is properly connected to the telephone line in the wall?