Problem connecting USB 34410

Similar Questions

• Problem connecting USB of Lenovo S890

  Hi, I just bought S890 a few days...

  and I wanted to connect to the computer with the help of the USB

  but it always show it me

  

  and I tried this also

  http://forums.Lenovo.com/T5/Lenovo-phones/S890-ideatool-connection-problem/TD-p/1083109

  but it still works no not for me...

  any solution for this?

  BTW when I simply search a file in my phone, I discovered that there is a file name is "Ideatool."

  and then inside got 2 .exe file with a picture of a question mark on the left side of the file.

  The file name is: ideatool_1.1.8_os.exe and LenovoUsbDriver_1.0.1.exe

  This file cannot be opened...

  My fixed only works if you have turned off all other drivers. You must uninstall all drivers Lenovo that comes with the phone, then follow the steps.

  HOWEVER, you must first try to use the drivers included in the phone itself. The drivers work under Windows. Therefore, transfer it to your computer to make it work. I had the same problem before, and I transfer the drivers by copying SD card, remove the SD card and copy it to the computer with the card reader. Then, run the file in Windows.

  If the included drivers do not work, so what you try my methods.

• Problem connecting USB to install HP Photosmart 5510 all-in-one inkjet

  Photosmart 5510 all-in-one inkjet

  Windows XP Pro x 86 (32-bit) service pack 3

  Software installs fine until he asking for the type of connection. The computer does not have wireless so I select USB connection and it fails every time. If I select to connect to PC later and plug in the USB, Windows detects new hardware (HP 5510) and asks where to look for drivers. When directed to the installation CD "Invalid data" error when copying files. In the Device Manager in the USB section it lists the Photosmart 5510 with a yellow! Selection of reinstall the driver results in an "impossible to install error.

  There is no other printer currently installed on the computer and the 5510 Photosmart is set as default printer. So far I have;

  tried different usb ports

  tried running the installer from the installation CD

  I tried to download updated drivers

  tried to install with disabled firewall and antivirus

  tried to install it in safe mode

  Same problem occurs every time. Any solutions or suggestions would be greatly appreciated!

  Thank you.

  Finally solved the problem. Had an old Pentium 3 machine around the pose and decided to try to change the disk hard on and see if I could install the printer with a different material.

  It turns out that the mup.sys file, which has something to do with PnP devices, has been damaged and Windows wouldn't start in the other Tower. Then, I took out the HARD drive and put it back in the Dell can reformat Windows XP and guess what, printer installed without a hitch the first time I tried! Now I have to reinstall everything on the computer * sigh *.

  In any case, the printer problem fixed!

• Problem connecting USB of blackBerry Smartphones

  I have a Curve 8330. Using Windows XP with the latest version of Blackberry Desktop (4.7).

  Neither the computer or the software BB, see the curve connected. No error message, just no connection. Good ports, cable and also installed the latest drivers USB of Blackberry Web site.

  Any ideas, please?

  Hello.

  Check the 8330 for debris or dirt in the USB port.

  If it's clean, it may be a hardware problem. Take it to the carrier and have then try

  to access via the USB port.

  Thank you

  Bifocals

  Don't forget to adjust your thread.

  Put the check mark in the green box containing your answer! Thank you

• Problem does not occur when it is not connected USB so that it looks like some sort of communication problem. The L355 worked perfectly.

  Hello

  I recently installed an Epson L555 instead of my Epson L355, which worked well with my software windows 7 and my BACK program based. However, whenever the L555 turned the printer just keeps ejecting the hopper pages until it is empty. On the menu screen, it says "printing", but there is nothing in the print queue and I didn't send anything to be printed. Sometimes it reads "Fax set auto answer. By pressing the Stop/Reset button stops the ejection pages and "Cancel" is displayed on the screen. This continues for about 2-3 minutes, then the pages start ejected again. Problem does not occur when it is not connected USB so that it looks like some sort of communication problem. The L355 worked perfectly.

  Hello

  Thanks for posting your query in the Microsoft community.

  I understand that print jobs are getting cancelled and I will be happy to answer your query. There could be several reasons for this cause and to diagnose the problem, initially, I ask you to refer to the suggestions in the article below and check.

  Solve printer problems

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• Problem with USB auto connect with clients that connect through the Security server...

  Lack of VMware View 5.0.1 with 2 servers connection and a security server. When the clients connect directly to the server connection, USB connection works very well... users can use their USB drives and other devices with their VM. The problem occurs when they attempt to use their USB devices when negotiated through the Security server.

  I know that port 32111 (TCP) must be open between the server security and the connection to the server, but even after doing so it does not always work... customers just to get the scrolling message of office in the USB menu initialization.

  Our current facility is:

  External IP address-> DMZ (Security Server)-> connect to server

  Entrust us our firewall config through our ISP (we are not overloaded with scientists here, it's just me, so things like little help my work load). They are certainly not incompetent (or at least were not in the past). I had to open the external 32111 IP port to the DMZ, then of the DMZ to our connection server that is used for external connections. Everything about VMware View works perfectly for the clients that connect this way, but not USB devices.

  One thing I give is if our having a configuration of VLAN dedicated for customers views influence what either. I'm trying to keep an eye on what ports are open that for our firewall for my records, but I do not see where I openly opened ports on the internal side of security server to our internal network. He must have the port opened directly from the internal face of security server of vmware 32111 discovers clients?

  The firewall Guys tell me that they checked over and over that port 32111 is open throughout the. They also said that they tried to telnet 32111 to our security server port and have nothing back (should have gotten garbage at least according to them).

  An idea of the next steps to take? It is obviously a blocked port, I just have no idea why at this stage.

  I know that port 32111 (TCP) must be open between the server security and the connection to the server, but even after doing it still does not work

  This is not what it takes. The agent is listening on the port 32111, you must open the firewall to allow connections to the Security server for the desktop on port 32111 (same thing you must allow RDP and PCoIP).

  Mike

• Check error: there was a problem connecting to the server Apple ID

  When I try to connect to my iTunes on my Windows laptop account it is said there is a problem connecting to the Apple ID server. This problem did not begin until 2 days. I have the latest version of iTunes and Windows.

  What is the number of the version of iTunes?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  Start by missing error MSI.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  Leave a post by: turingtest2

  On the PC, when connecting each device, it loads a separate driver. You can try this trick when you want to get iTunes recognizes the iPhone 6. Thanks to the user of the CSA turingtest2 for the tip.

  Try the following:

  Open Control Panel > Device Manager

  Plug in your device

  Locate Bus USB Controllers > Apple Mobile Device USB Driver.
  It is also possible that the device may appear under imaging devices, portable devices or other devices or as a device USB of MTB.

  Right-click and select software update of the driver...

  Click Browse my computer for driver software

  Go to C:\Program Files\Common Apple Mobile Device Support\Drivers or
  C:\Program Files (x 86) \Common Files\Apple\Mobile Device Support\Drivers

  Click on let me pick from a list of drivers for devices on my computer

  Click on Apple Mobile Device USB Driver

  Click Next, then close and exit the Device Manager

  Leave a post by: ChrisJ4203

• Connect USB hard drive to the SD2010KY DVD player

  Hi there Aussieland...

  * More about SD2010KY DVD player + * bought on a month back...

  Any kind dbo know the answer to:

  Could it be caused damage to run a USB connection external 3 1/2 "HD (160 g) - say a .avi movie - into the USB port on the front of the unit?

  That is to say, power supply of the unit will be responsible for the extra bit Ok?

  Or is this the wrong forum to ask this detail? :)

  Thank you - everything you need to know about would of course be appreciated...

  See you soon

  To be honest, it is Toshiba forum created for calculation problems.
  In any case, check the drive specification to see if the USB port has enough power for external HARD disk. I had old DVD player and I could only use USB keys.

  You can try to connect USB HDD to see if the drive will be recognized correctly. You won't damage anything.

• problem mouse USB

  Hello

  I bought Tohsiba satellite a50-106.

  for this model, I bought the optical mouse A4 Tech AK-5, but after you have connected to comp, it doesn't.
  technicly mouse it's ok, I checked on my desk.

  After connection to the optical sensor usb in the mouse does not light, but there is new message device to find, then comes another message, which is device may not work correctly. Does not install the mouse drivers.

  When I get out the slot usb mouse comes another problem. USB slot is inactive (not see). When I connect diferent peripheral (floppy drive) system not to see too.

  I need to uninstall & then install the drivers for the usb hub.

  If any 1 know whwt 2 so that the work of memo please help me.

  Hello

  Do you have a few with this mouse driver CD? You have the same problem with all three USB ports? Can you also check the BIOS settings if there is option called the pointing device settings. There are a few options. You can change it with the space bar. I don't know, but there must be option called simultaneous or something like that.

• Big problems with USB devices

  Since I upgraded to El Capitan I have several, serious problems with USB devices:

  1 USB hard drive: everything by watching a video from an external hard drive, the hard drive will be to disassemble all the minutes, the video will be of course hang and it takes 45-60 seconds until the drive reconnects. I also can not boot from any external hard drive more. Booting from a USB key works fine.

  2. I can't transfer my Sunny BT11 of beam data more. The Sunny Beam is a device that records the data of my photovoltaic plant. The overview of the system he sees when connected via USB, however he is not recognized and so I can't transfer data files. Also, it makes not a difference if it is connected via a USB hub or directly, the two versions do NOT work. In the Finder preferences, all devices are controlled to display on the desktop.

  The two scenarios always perfectly work with my Mac mini that has not been updated and uses Mac OS X 10.10.

  Hello Gulliver,

  It seems that if you live with loss of connection of your USB devices since the installation of Mac OS X 10.11 El Capitan, is that correct?

  I suggest that you are troubleshooting by following the steps in this article - OS X El Capitan: If a USB device does not work

  Thank you for using communities of Apple Support.

  Sincerely.

• HP Photosmart B110: Solutions Center installs - problems of usb - only wanted to scan - how to install the scanner part

  -With the help of HP Photosmart B110

  -Use of Tower/Desktop computer running Windows 7 64 bit

  Printer/Scanner connected via WiFi to router

  -Printer part works, I can print to this device

  -Scanner is accessible via the device Web page.

  I want the software of the scanner Solutions Center.

  I can't install the Solutions Center on Windows 7 64 bit. Setup stops and says that I have USB hardware and driver problems. USB on my Tower is USB2 and USB3 ports. Everything works perfectly and the Windows Device Manager has no problem with USB drivers/devices.

  How can I install the scanner software (or all of the Solutions Center software)?

  Tried to look in the folder for the files of instsaller scanner, nothing seems to work. (pulled other positions where it not install Solutions Center). Computer is working very well, so my only option at the moment is to look through the device's Web page, but it is not the best. And I would like to use the software. Also one third of the software "fax and scan" software and windows does not see the connected B110 (probably because it is on a network and not directly plugged into a usb port), so these two options came out.

  HP forum, help please. Is there a way to bypass the usb part? I use this device on a network. Windows 7 sees (even if only as a printer), so also want windows to consider it as a scanner as well.

  Thank you

  Hi @jedi11csa,

  Thank you very much to get back again.

  I just talked with a few colleagues in this regard, and this problem seems to be more a matter of Windows operating system, if the computer displays that USB related errors as well as the installation had not yet reached the point where it asks you to select your connection type.

  Maybe it's an investigation that is best suited for community Microsoft Forums as my resources have been exhausted in this respect.

  I hope that you are able to find the solution you need.

  Thank you.

• problem ejecting usb mass storage device

  After the synchronization when you try to eject the ipod's message problem ejecting usb mass storage device

  Are eject you using the eject of the iPod in iTunes?

  If you do not have the case, restart the computer with the always-connected iPod.  After reboot, this problem persists?

• Device USB not recognized - device connected USB has malfunctioned and Windows does not recognize it

  I have a HP Pavilion dv4 laptop running Windows 7 Home Edition Premium and the USB ports worked well for a HP deskjet printer and an older Casio digital camera. Then one day, the laptop decided not to recognize the Casio digital camera and gave the error message "USB device not recognized" and also indicated that the device connected to the computer has malfunctioned. This prompted me to buy a new digital camera Canon. Well, a new camera has not fixed the problem. Now, anything that is connected to one of the 2 ports USB will not be recognized by my laptop. Help!  I am at a loss to understand this.  I tried using Microsoft suggested below:

  Suggestion 1: the problem with USB devices, uninstall and reinstall all USB controllers. This allows controllers to recover the port USB of his condition does not respond.
  USB controllers represent the USB ports in Device Manager.

  a. Click Start, type Manager of devices in the search box of start and press ENTER.
  b. expand Bus USB controllers.
  Note: you may scroll through the list to find this point.
  c. the first USB controller under Bus USB controllers right click and then click on uninstall to remove it.
  d. Repeat steps above for each controller USB is listed under Bus USB controllers.
  e. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.
  f. check the USB device to see if it works.

  This has not fixed the problem.  Then the Device Manager, I tried to update the drivers on all the USB controllers and root hubs. While some may have received software updates downloaded, it still has not corrected the problem of unrecognized USB device after the computer is restarted.  I hope that someone knows the solution to this situation and can pass it on to me. Thanks for reading and any help display.

  Read previous messages revealed the solution for USB devices not recognized on my HP Pavilion as well as several other laptop models.  Shut down the computer and remove the battery and wait for about 15 minutes. Reinstall the battery and restart the computer.  USB ports are working to download pictures from my digital camera from Canon and charging a cell phone, etc...   I hope it helps others with this problem!

• Application that created on another computer will not connect usb-camera

  Hello, friends!

  I have a problem:

  My application that was created on my computer does not connect usb-camera on the other computer. I installed the LabView run-time engine and the runtime of vision on this computer but it is not useful :-(application is open, but the usb device not running.

  I'll be thanked for any help with this problem!

  Thank you very much!

  It's the solution to the problem:

  Solution:
  To run an exe containing NEITHER-IMAQ for USB functions, follow these steps on the computer that is running the EXE file:

  1. Install the following execution engines:
     • LabVIEW Run - time Engine (same version that was used to develop the VI)
     • Execution of vision engine (same version that was used to develop the VI)
       • One Vision single-seater deployment license is required for each computer target on which you install the runtime of the Vision. See all the related links for more details.
  2. Copy the following dll files to the directory on your development computer system, usually C:\Windows\system32 directory of your target machine system.
     • ImaqDirectShowDll.dll
     • ImaqDirectShowExport.dll
  3. Register at ImaqDirectShowExport.dll by the Windows Start Menu , click run. Type regsvr32 C:\WINDOWS\system32\ImaqDirectShowExport.dll, and then click OK to register the DLL.

     If you are on a different operating system or if the system folder is different and that you want to copy the path instead of typing all the way, you can drag the file to the command line at the prompt to run it, highlight the path, right-click and select it copy.  Paste in the command prompt by right-clicking and selecting window block.

     The ImaqDirectShowDll doesn't have to be registered.

  Once these steps are completed, and the DLL is registered successfully, your EXE will work.  Vision Acquisition software or Vision Development Module must be installed on the target computer.

• HP Pavilion 15-n203sx: problem of usb 3.0 of 15-n203sx HP Pavilion with Windows 10

  I managed to install all the Windows 10 and some drivers Windows 8.1 left.

  My problem is when I connect my external usb3.0 HARD drive to the USB 2.0 on the right, it connects successfully, but when I connect it to two ports usb3.0 on the left, the HARD drive lights, but it does not appear in windows. I suspect that the ports are not fed enough current (amperage).

  I suspect that the reason is the generic driver from Microsoft for the eXtensible Host Controller:

  

  I tried to install the driver Windows 8.1:

  HP 3005pr USB 3.0 Port Replicator driver 7.6.56275.0 Rev.A

  or https://downloadcenter.intel.com/download/22824

  or http://h20566.www2.hp.com/hpsc/swd/public/detail?sp4ts.oid=5405424&idx=&swEnvOID=4059&action=driverD...

  But all have failed to install.

  Help, please!

  Hi @ahmedz_1991,

  Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!

  I stumbled upon your post on the laptop and wanted to help you! I looked in your question about your HP Pavilion Notebook 15-n203sx and problems with USB 3.0 does not properly. Here is a download that I found for Windows 10 and HP 3005pr USB 3.0 Port Replicator which should solve your problems. You need to uninstall both Intel that are listed, and then install the Windows 10 we. Once the installation is complete, restart your laptop and check the drivers.

  I hope it suits it.

  Please let me know how it goes.

  Thank you.