Problem of PowerEdge 850-> 6 GB 2 GB memory upgrade

Similar Questions

• ESX 3.5 u4 RAID 1 on PowerEdge 850

  Hi all

  I have a small question, I used to have an ESX Server 3.5 to u4 mode RAID 0 on a Dell PowerEdge 850. Finally, the system crashed, the RAID array will be more found.

  I decided to re - install ESX 3.5 u4 but with RAID 1 instead. During the installation process and after the installation are finished, I heard a plaintive high-pitch noise when the array is initialize, now it does not when I put the RAID 0 configuration and install ESX. I also tried with ESXi 3.5 u4 but get the same results with RAID 1.

  I checked on the VMWare Web site, with the compatibility tool and the PowerEdge 850 is not listed in the compatible Dell servers to ESX 3.5 u4, but as I have explained before use to run ESX on this same PowerEdge without problems.

  I am trying to pin-point the source of the problem and I would like to know if any of you correctly installed ESXi or ESX on a PowerEdge 850 with RAID 1?

  BTW, I ran tons of diagnosis on the system, and the HARD drive and all the components are healthy. That's why I wonder if the problem is not with the software and hardware.

  Thanks to you all!

  Any input is appreciated

  Hello

  I also had these problems with ESXi 3.5 u4 - but only if I installed immediately after creating the RAID1 array. The high pitched noise is the "RAID degraded" alarm on the CERC SATA 1.5/6 controller that comes with this system. My solution was to allow the RAID to build entirely during the night before installing u4, which allowed me to install, and I've been running for a month now without any problems. From one day to the next, I say only because they were 500 GB disks and took some time to build completely.

  Furthermore, I have now decided to return to u3 u4 disables many management utilities I was going to use (using the "unsupported" and RCLI). After the RAID reset, I tried to install u3 immediately (during the process of RECONSTRUCTION/VERIFY) and managed without a building during the night.

  A warning on the u4: even if he can be downloaded version of Dell (with the CIMs Dell preinstalled for use with OpenManage), the CIMs are missing the most critical readings on the State of the RAID. The other hardware monitoring is pretty irrelevant compared to know when your RAID array is degraded and must be repaired.

  If anyone has solutions to get the controller CERC report thorugh either OpenMaanage or SNMP so please point me in the right direction.

  Good luck.

• Ventole Rumorose DELL PowerEdge 850

  Buongiorno,

  avrei need di UN preventivo relativamente all'intervento di a vostro tecnico per sostituzione del corpo che sono diventate ventole molto rumorose knew a Dell powerEdge 850 service tag 93F5F2J.

  In attesa di a vostro riscontro Patu speaking saluti

  Marco

  Buongiorno, OTS will in privato a ' manage the request email.

  Grazie

  Marco

• HP Envy 850-065SE: memory upgrade problem

  HP computer: Envy 850-065SE (memory 4 locations)

  Memory: G.SKILL RIPJAWS V F4-2133C15D-32GVR DDR4-2133 CL 15-15-15-36 v 1.2 2 * 16GB

  I just bought 32 GB (2 * 16) G.SKILL RIPJAWS V F4-2133C15D-32GVR DDR4-2133 CL 15-15-15-36 v 1.2 memory to upgrade my HP desktop computer (model 850-065SE of envy). My office has a HP mother 2B3A and i7 - 5820 k and HaswellE chipset. The memory of the plant is of Samsung brand with configuration DDR4-2133.

  When I replaced the memory of samsung (trademark) with G.SKILL ones, the computer cannot start with black screen. When I've switched back to factory memory, the computer is back to normal.

  That means G.SKILL RIPJAWS V 16 GB memoryis is not compatible with this HP computer motherboard? or upgrade the BIOS can solve this problem? or do I return these memory and get 8 GB * 2 instead? Your comments are much appreciated.

  This model is limited to only 4 GB and 8 GB modules in the slot.

  B21 HP

  CL15 - DIMMs, 4 GB, PC4-17000, 798033-001, DDR4 COMPLY_2.07

  CL15 memory - DIMM, 8 GB, PC4-17000, 798034-001, DDR4 COMPLY_2.07

  You can buy online modules of 8GB.  Look at the technical on this point.

  https://www.CDW.com/shop/products/Kingston-DDR4-8-GB-DIMM-288-pin/3912220.aspx#Po

• PROBLEMA SU POWEREDGE T310

  Buongiorno, ho a sul problema server.

  Spero schermata in hoist possa essere di aiuto.

  avrei need di avere un preventivo by the riparazione.

  per ora grazie

  Buongiorno, the sto contattando by mail.

• Dell Poweredge 850

  Good so I had to deal with a perc 4/SC for a day or two to find that it is not compatible with 2008 r2.

  I need to upgrade 4e/DC I think. Is their any conflict of hardware I need to know?

  Is their a process for the replacement of a raid controller I need to know? Where is the best place to buy a 4th/DC?

  so I understand this system is old and replace the system would be easier but I was handed the project to get this upgrade and I do not disaapoint.

  any information that you consider, I got useful would be appreciated.

  No, the two controllers are fully supported in the 850. I updated the firmware of the system before installation if (BIOS and ESM first, then another firmware or system).

• Problema launch Poweredge 2800 [MS]

  Ointment in fase di boot message Poweredge2800:

  incompatibility of configuration unresolved between the drives and the NVRAM on the adapter. Allégo Foto

  Come e possibile risolvere he problema senza perdere I dati contenuti negli hdd?

  Configurazione current 2 HDD(id0 id1) in raid 1 e tutto it restaurant in raid 5

  Bene cosi! Probabilmente it server TR e spento di botto a seguito di caduta side.

  Speaking saluti

  Manual

• [EC |] Solved] Problema Server PowerEdge T110 II

  Buongiono, Devo re-installare he operating system, my sommergibili TR blocca perched not are rilevati gli on hard drive.

  Credo di dover download driver I del RAID, not if quali sono quelli giusti.

  I would UN aiuto su come poter procedere. Grazie

  Perfetto! to ha siamo need that.

  EC

• Problem in mapping partition VMFS of iSCSI (MON) after upgrade to ESXi 4.0

  Hi all

  I've got 2 x Dell PowerEdge 2950 III linked directly with Dell MD3000i iSCSI-SAN and today I had once hard to improve my production ESXi 3.5 u 4 ESXi 4.0,.

  First is that the upgrade is failed miserably after following this thread: http://communities.vmware.com/thread/211413;jsessionid=47217F9BCCA2DF1325DBE7A266D48A8D?tstart=0

  with the following error: ERROR: boot disk not supported

  The layout of boot device on the host computer does not support the upgrade.

  and second is that after reinstalling clean and lost all unique settings on my ESXi host, I am now stuck in SAN iSCSI partition mapping after following the guide from: support.dell.com/support/edocs/software/eslvmwre/AdditionalDocs/cnfigrtn* guide/storage* _guide.pdf

  See the following attachment.

  I wonder how do people in the production system running ESXi 3.5 u 4 filled with hundreds of VM?

  any idea and suggestion would be welcomed gladly.

  Thank you.

  Kind regards

  AWT

  Same thread: Re: ESXi 3.5 4 problem to upgrade by adding the VMFS partition existing on iSCSI SAN

  Have you solved the problem by using the new analysis?

  André

  * If you found this device or any other answer useful please consider awarding points for correct or helpful answers

• Problems of ' 09 Time Capsule to the Airport Extreme upgrade

  I with success the setup a new Airport Extreme (AE) and I want to continue to use my Time Capsule (TC) 2009 as a backup drive. However, I have questions. What is the right way to implement these devices to play nice?

  I have currently the modem ethernet fall on the AE WAN ethernet. Then I have another ethernet cable connecting the AE LAN ethernet in the TC WAN.

  In addition, I have the TC Network Mode as 'OFF' and his router Mode as 'Off (Bridge Mode).

  Is everything is OK?

  All correct so far.  Also check the Internet tab to ensure that the TC is to connect using DHCP = AirPort Utility.

  

  At this point, what other problems are live you?

• Satellite A660 - 11 M - Memory Upgrade - problem

  Hello world!

  I'm having a problem with upgrading my RAm 4 GB to 8 GB memory ([link crucial 8 GB Kit | http://www.crucial.com/eu/store/mpartspecs.aspx?mtbpoid=28543EEAA5CA7304]) which should be compatible.

  When I turn on the laptop after mounting of the modules to all first all seem to be right and the Bios start, but then it will not load windows and stucks on a black screen.

  Could someone help?

  Thank you!

  Hello

  What to say: it looks like it s a problem with new RAM modules.
  The RAM modules aren t fully compatible or they malfunction.
  You must use other modules I made good experiences with modules from Kingston.

• Satellite L10-117 and memory upgrade problem.

  I installed the module of ram kingston 512 MB dedicated for my laptop and my system does not start. Laptop does not see its partition with windows. I tried to salvage the dvd system and he does ' t help. Recovery is going ok but after restart problem is the same. I also tried to install this memory module 256 MB (factory installed), and then my black LCD screen and the computer won't shut down. Akku only delete help to extinguish.
  I tried all combinations of this module in the memory 1 and 2 location.
  I use 1.8 BIOS and there I see almost empty memory.

  Hello

  If you start the unit with the original just module becomes so everything ok?

• Satellite 2140cds MEMORY UPGRADE PROBLEMS

  I currently own a 2140CDS satellite with 32 MB of ram standard.

  I bought a module of memory of 128 MB (128 MB 144pin SODIMM PC100 3.3V CL = 2) of technology crucial to take my ram up to the maximum of 160 MB.

  When I install the RAM, the computer doesn't recognize it, and I get no error while starting the system, the system shows still 32 MB

  I had verified memory module and it works well, I had my slot memory computers checked to see if he had any problem with it. The computer and the module of memory seem to have no failure.

  Can anyone give me a hint or help to solve this problem.
  If I need to use memory from another provider IE KINGSTON

  Concerning

  Scott Bremner

  Hi Scott,.

  I suggest these two modules autour swapping or just use the new 128 MB module to the main location.

  Also, make sure that the modules of memory are firmly and correctly locked in place.

  The normal recommendation is to use only authentic RAM Toshiba modules, but personally, I use the RAM modules that I got from ORCA, so I don't think that there should be no problem with your crucial.

  HTH

• Satellite C75-A-144 - Kingston memory upgrade problem

  Hello

  I recently bought a laptop C75-A-144 and wanted to do an upgrade with the bar of memory KINGSTON 4 GB (4GB 1600 Mhz DDR3 Non - ECC CL11 SODIMM SRx 8).
  Unfortunately, the laptop does not start with this module installed. I checked the module in the other laptop (differrent manufacturer) and it works well.
  Then... there at - it some compatibility problem with Kingston memory modules and model C75-A-144?

  In addition, because I really want to do this upgrade, can someone give me a list of the modules that will work with this laptop?

  Thanks in advance for your help.

  According to specification for laptop, that your computer can be upgraded up to 32 GB of RAM.
  Compatible RAM modules (verified by Toshiba) followed part numbers:
  2 GB DDR3L-1600-PA5104U-1M2G
  4 GB DDR3L-1600-PA5104U-1M4G
  8 GB DDR3L-1600-PA5104U-1M8G

  Check it please these part numbers and use them to order of RAM.

  In the past I ve used memory modules RAM Kingston for upgrade and there is no problem at all. Maybe you're trying to use Rams with different specifications.

• HP Envy Notebook m6-1125dx: no problems with the HP Envy m6 at 10 Windows upgrade?

  I plan the upgrade of Windows 10 of my HP ENVY m6-1125dx Notebook PC (Intel Core i5 - 3210M CPU) and need to know if this computer will be compatible with Windows 10. Because the HP support Web site now requires a scanning system to report on the drivers available, I have no way of knowing if there are any drivers Windows 10 available (or if they are still required). I thought that maybe I could send an e-mail or chat with HP to see what they have to say, but they want $60 to answer a question!

  Please let know us if anyone has experience (good or bad) with 10 of Windows upgrade for th want m6.

  Hüffer,

  Just an update... I followed your advice and installed upgrading on-site instead of clean, and everything seems to work fine. The only real glitch, I met was the trackpad settings have been changed which because of many problems, but I could attack while going in the Synaptics Control Panel and reset everything to the way I like them.

  Thanks again for the help and I'll review it "resolved".